TOPO化学修饰碳糊电极阴极伏安法测定金

本文研究了TOPO—化学修饰碳糊电极测定金。在不加电压情况下于0.1～1.0mol·L-~1HCl介质中进行化学富集,+0.6V～-0.1V范围阴极扫描,+0.20V出现的还原峰高与金浓度0.4～1000ng.ml~(-1)范围内成线性关系。改换底液溶出时,铁允许量可达10000倍而不干扰金的测定。用于合金样品中金的测定,结果满意。并讨论了电极反应的机理。     

槲皮素化学修饰碳糊电极吸附溶出伏安法测定痕量铅

建立了用槲皮素修饰碳糊电极测定痕量铅的新方法 ,在 0 .1 0mol L甲酸盐缓冲液 (pH 4.3 )中 ,于 -0 .1 0V(vs.SCE)搅拌富集 ,再在 -0 .70V静止还原 40s后 ,阳极化扫描 ,于 -0 .42V左右获得一灵敏的铅阳极溶出峰。在最佳条件下 ,富集不同时间 ,其二次导数峰电流与Pb2 + 在 1 .0× 1 0 - 8～ 8.0× 1 0 - 7mol L和 2 .0× 1 0 - 9～ 6.0× 1 0 - 8mol L两个范围内呈线性关系 ,检出限为 8.0× 1 0 - 1 0 mol L(S N =3 )。同时初步探讨了电极反应机理。     

丁二酮肟化学修饰碳糊电极测定微量钯

报道了丁二酮肟化学修饰碳糊电极用于测定微量钯的研究。实验表明，Pd（Ⅱ）浓度在1×10－4～5×10－7mol·L－1范围内呈良好的线性关系。对模拟样进行了测定。     

微分脉冲伏安法测定生物素

用微分脉冲阳极伏安法研究了生物素的电化学行为，用金电极作工作电极，在ｐＨ３．５９的ＨＡｃ－ＮａＡｃ介质中，生物素的峰电位为０．４６Ｖ，生物素浓度在１．０×１０－６～２．０×１０－５ｍｏｌ／Ｌ范围内与峰高呈线性关系。本法应用于含生物素样品的分析，可以不经分离，直接测定。此外，还用循环伏安法研究了电极反应的可逆性。     

纳米CeO2修饰碳糊电极微分脉冲伏安法对盐酸克伦特罗的测定

研究了盐酸克伦特罗(CLB)在纳米CeO2修饰碳糊电极上的电化学行为.结果表明:在0.10 mol·L-1的HClO4溶液中,CLB于+0.40 V(vs SCE)左右处产生1对准可逆的氧化还原峰.与裸碳糊电极相比,CLB在修饰电极上的电流响应明显增大,据此建立了尿样中CLB的微分脉冲伏安测定方法.线性范围为5.0×10-9 ～6.0×10-6 mol·L-1(r=0.998 2,n=7),检出限为2.5×10-9 mol·L-1(3sb),加标回收率为96% ～104%.     

二茂铁修饰碳糊电极示差脉冲伏安法测定槲皮素

制备了二茂铁修饰碳糊电极,并采用循环伏安法研究了槲皮素在该修饰电极上的电化学行为。研究发现:在pH 6.2磷酸盐缓冲溶液中,修饰电极对槲皮素有良好的电催化作用,得到了一对氧化还原峰,其氧化反应是受吸附控制的两电子、两质子电极过程。并在此基础上提出了一种测定槲皮素的示差脉冲伏安法。试验结果表明:槲皮素的氧化峰电流与其浓度在8×10-4～2×10-6 mol.L-1范围内呈线性关系,检出限(3S/N)为7×10-6 mol.L-1。     

阳极微分脉冲伏安法测定麦迪霉素

探讨了不同pH溶液中,麦迪霉素在玻碳电极上的伏安行为。在pH=7.0的NH_4Ac溶液中,麦迪霉素有一个灵敏的氧化峰,阳极微分脉冲扫描峰电位为 0.81V(vs·SCE)。其浓度在10×10~(-7)～1.5×10~(-5)mol/L范围内与微分脉冲伏安峰电流呈线性关系,检测限为5×10~(-8)mol/L。     

微分脉冲阴极溶出伏安法测定呋喃唑酮

研究了呋喃唑酮在玻碳电极上的伏安行为。在 1mol LHCl底液中 ,用微分脉冲阴极溶出伏安法得到一灵敏的呋喃唑酮还原峰 ,峰电位为 0 .0 38V(vs.Ag AgCl)。峰电流与呋喃唑酮浓度在 8× 1 0 -6～ 1× 1 0 -4 mol L范围内呈线性关系 (r=0 .9984) ,检出限为 8× 1 0 -8mol L。该法已用于片剂与合成血清样品中呋喃唑酮含量的测定     

胆红素的伏安特性及其微分脉冲伏安法测定

建立中成药中胆红素定量测定的微分脉冲伏安法。在多种介质中研究胆红素在玻碳电极上的电化学行为 ,全面优化条件后 ,采用标准加入法对中成药中胆红素进行测定 ,并通过与药典中标准方法对照和干扰实验及回收率实验对本方法进行评价。在 0 .2mol·L-1HAc NaAc 5 0 %EtOH和 1 1 5mol·L-1KH2 PO4 Na2 HPO4 溶液中 ,峰电流与胆红素浓度分别在 6.2 5× 1 0 -7～ 1 .0 0× 1 0 -5mol·L-1(r=0 .9976)和 5 .0 0× 1 0 -8～ 3.0 0× 1 0 -6mol·L-1(r=0 .9939)范围内呈良好的线性关系 ,检测下限分别为 5 .0× 1 0 -8mol·L-1和 5 .0× 1 0 -9mol·L-1。众生丸和牛黄解毒片中胆红素的质量分数分别为 0 .0 86%和 0 .1 0 9% ,RSD分别为 3 4%和 3.0 % ,回收率为 96.6%～ 1 0 4 .1 % ,其结果与药典中标准方法测定结果基本一致。     

碳纳米纤维修饰碳糊电极用于双酚A的电化学检测

制备了碳纳米纤维修饰碳糊电极,并用于双酚A的高灵敏和高选择性电化学检测。碳纳米纤维材料经静电纺丝和碳化过程相结合制备而成,采用滴涂的方法修饰于碳糊电极表面制成电化学传感器。利用循环伏安法、交流阻抗法以及微分脉冲伏安法考察了传感器的性质及双酚A的电化学行为。结果表明,双酚A的峰电流响应与其浓度在0.8~50μmol/L之间呈良好的线性关系,检测限为0.1μmol/L。构建的电化学传感器用于环境水样中双酚A的检测具有较高的回收率。     

Voltammetric Determination of Selected Aminoquinolines Using Carbon Paste Electrode

Optimum conditions have been found for voltammetric determination of mutagenic 5‐aminoquinoline, 6‐aminoquinoline and 3‐aminoquinoline by differential pulse voltammetry and adsorptive stripping differential pulse voltammetry on carbon paste electrode. The lowest limits of determination were found for adsorptive stripping differential pulse voltammetry in 0.1 mol dm^?3 H₃PO₄ (5×10^?7 mol dm^?3 , 1×10^?7 mol dm^?3, and 1×10^?7 mol dm^?3 for 5‐aminoquinoline, 6‐aminoquinoline and 3‐aminoquinoline, respectively). The possibility to determine mixtures of 8‐aminoquinoline with 3‐aminoquinoline or 5‐aminoquinoline or 6‐aminoquinoline, and mixtures of 5‐aminoquinoline with 3‐aminoquinoline or 6‐aminoquinoline by differential pulse voltammetry was verified. Binary mixtures of 8‐aminoquinoline with 3‐aminoquinoline or 6‐aminoquinoline, and of 3‐aminoquinoline with 5‐aminoquinoline could be successfully analyzed.     

Electrochemical Analysis of D‐Penicillamine Using a Carbon Paste Electrode Modified with Ferrocene Carboxylic Acid

The electrochemical behavior of D ‐penicillamine (D ‐PA) studied at the surface of ferrocene carboxylic acid modified carbon paste electrode (FCAMCPE) in aqueous media using cyclic voltammetry and double step potential chronoamperometry. It has been found that under optimum condition (pH 7.00), the oxidation of D ‐PA at surface of such an electrode is occurred about 420 mV less positive than that an unmodified carbon paste electrode (CPE). The catalytic oxidation peak current was linearly dependent on the D ‐PA concentration and a linear calibration curve was obtained in the ranges 7.5×10^?5 M – 1.0×10^?3 M and 6.5×10^?6 M?1.0×10^?4 M of D ‐PA with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 6.04×10^?5 M and 6.15×10^?6 M. This method was also used for the determination of D ‐PA in pharmaceutical preparation (capsules) by standard addition method.     

Carbon Paste Electrode Modified by Surfactant for Anodic Stripping Voltammetric Determination of Sulphadiazine

ＣａｒｂｏｎＰａｓｔｅＥｌｅｃｔｒｏｄｅＭｏｄｉｆｉｅｄｂｙＳｕｒｆａｃｔａｎｔｆｏｒＡｎｏｄｉｃＳｔｒｉｐｐｉｎｇＶｏｌｔａｍｍｅｔｒｉｃＤｅｔｅｒｍｉｎａｔｉｏｎｏｆＳｕｌｐｈａｄｉａｚｉｎｅＺｈａｎｇＺｈｅｎｇ－ｑｉ；ＣｈｅｎＺｈａｎ－ｇｕａｎ...     

Lead Determination by Anodic Stripping Voltammetry Using a p‐Phenylenediamine Modified Carbon Paste Electrode

Carbon paste electrodes were modified by mixing appropriate amounts of the monomers o‐phenylendiamine, p‐phenylendiamine and m‐phenylendiamine (o‐PD, p‐PD and m‐PD) into a graphite powder‐paraffin oil matrix. The electropolymerization of the incorporated phenylendiamine was then carried out in a carbon paste electrode in acidic medium by cyclic voltammetry between ?0.30 V and +0.90 or under constant potential. The modified carbon paste electrodes (MCPEs) obtained by this electropolymerization method were found to be useful for trace determination of Pb²⁺ in aqueous solutions. Lead(II) was first preconcentrated on the modified electrodes by complexation with the modifier, and the electrode was then transferred to an electrochemical cell. The best results in terms of sensitivity and detection limit were obtained with poly p‐phenylenediamine (poly (p‐PD)). For a 10‐min preconcentration time, the calibration plot was linear from 5×10^?8 mol L^?1 to 10^?5 mol L^?1, with r²=0.999 and relative standard deviation equal to 5%. However, the lowest lead concentration that could be detected was 10^?9 mol L^?1. Interference from metal ions like Cd(II), Hg(II), Zn(II), Fe(II) and Cu(II) was also studied.     

碳糊电极阳极吸附伏安法测定大黄酸

在pH4.2的HAc-NaAc底液中,大黄酸在碳糊电极(CPE)上有一灵敏的吸附氧化峰,峰电位为1.14V(vs.SCE)。该氧化峰的二阶导数峰电流与大黄酸的浓度在8.0×10-9~8.0×10-7mol/L(富集120s)范围内呈良好的线性关系(r=0.998),检出限为2×10-9mol/L(S/N=3,富集180s)。探讨了大黄酸在CPE上的伏安性质和电极反应机理,并将本法应用于中药大黄中的大黄酸的测定,结果良好。     

Determination of Trace Copper by Adsorptive Voltammetry Using a Multiwalled Carbon Nanotube Modified Carbon Paste Electrode

A new method for the determination of trace copper was described. A multiwalled carbon nanotube modified carbon paste electrode was prepared and the adsorptive voltammetric behavior of copper‐alizarin red S (ARS) complex at the modified electrode was investigated. By use of the second‐order derivative linear sweep voltammetry, it was found that in 0.04 mol/L acetate buffer solution (pH 4.2) containing 4×10^?6 mol/L ARS, when accumulation potential is 0 mV, accumulation time is 60 s and scan rate is 100 mV/s, the complex can be adsorbed on the surface of the electrode, yielding one sensitive reduction peak at ?172 mV (vs. SCE). The peak current of the complex is proportional to the concentration of Cu(II) in the range of 2.0×10^?11–4.0×10^?7 mol L^?1 with a detection limit (S/N=3) of 8.0×10^?12 mol/L (4 min accumulation). The proposed method was successfully applied to the determination of copper in biological samples with satisfactory results, the recoveries were found to be 96%–102%.     

奥美拉唑在碳糊电极上的吸附伏安测定法研究

研究了奥美拉唑在碳糊电极上的电化学行为及检测方法 ;在1.2mol·L -1H2SO4 底液中 ,通过富集用碳糊电极吸附伏安法测定奥美拉唑 ;阴极峰电位为0.403V(vsSCE) ,峰电流与奥美拉唑的浓度在7.8×10-8～3.7×10-5 mol·L-1 范围内呈良好的线性关系 ;该法的检出限为1.43×10-8 mol·L-1;用标准加入法测得回收率范围为94 %～102 % ;对奥美拉唑胶囊用该法进行了测定 ,获得了满意的结果 ;该法的优点是成本低 ,操作方便 ,重复性好及检出限较低 ;对电极响应机理进行了探讨 ,奥美拉唑的电极过程是一个两电子两质子的准可逆过程     

掺杂硒修饰碳糊电极伏安法测定对乙酰氨基酚

采用循环伏安法制备了掺杂硒修饰碳糊电极,用循环伏安法和差分脉冲伏安法研究了对乙酰氨基酚在掺杂硒修饰碳糊电极上的电化学行为,建立了掺杂硒修饰碳糊电极测定对乙酰氨基酚的电化学方法。在pH 4.6的0.1mol·L-1乙酸-乙酸钠缓冲溶液中,对乙酰氨基酚在+0.61V呈现一个灵敏的氧化峰。对乙酰氨基酚的浓度在6.0×10-7~1.5×10-4 mol·L-1范围内与其氧化峰电流呈线性关系,检出限(3s/k)为2.8×10-7 mol·L-1。方法用于药品中对乙酰氨基酚的测定,测定结果与药典法测定值相符,测定值的相对标准偏差(n=5)在2.1%~2.5%之间。