Dual electrochemical microsensor for simultaneous measurements of nitric oxide and oxygen: Fabrication and characterization

A planar-type amperometric dual microsensor was developed for the simultaneous measurement of the nitric oxide (NO) and oxygen (O₂) concentrations. The sensor (overall diameter = 500 μm) consisted of a dual working electrode (WE) containing two platinized platinum microdisks (25 μm diameter, WE1, WE2, distance between two disks > 330 μm) and a Ag/AgCl wire reference electrode covered with an expanded poly(tetrafluoroethylene) gas-permeable membrane. The differentiation and concurrent measurements of NO and O₂ were obtained successfully using two sensing WEs with different applied potentials (+0.75 V for WE1 and −0.4 V for WE2). Cross-talk between WE1 and WE2 was eliminated with an optimized internal solution composition. Linear dynamic range, selectivity, sensitivity, detection limit (<5 nM for NO; <500 nM for O₂), and stability (>50 h) were evaluated.     

Isoconversional kinetics of degradation of polyvinylpyrrolidone used as a matrix for ammonium nitrate stabilization

Thermogravimetric analyzer (TGA) has been applied to measure the kinetics of the thermal degradation of virgin polyvinylpyrrolidone (PVP) and a phase stabilized PVP–ammonium nitrate (AN) material. The PVP–AN samples have been prepared by using 20 wt.% of AN and PVP of three different molecular weights. Virgin PVP undergoes a major mass loss in the region 380–550 °C leaving a small amount of nonvolatile residue. The application of an advanced isoconversional method to the respective degradation process demonstrates that its effective activation energy increases from 70 kJ mol⁻¹ to a plateau value at 250–300 kJ mol⁻¹, which is independent of the molecular weight. The PVP–AN materials lose spontaneously 20% of their mass on heating above the glass transition temperature of the PVP matrix (160–180 °C). After the escape of AN, the remaining PVP matrix degrades in the same temperature region as virgin PVP, however, the effective activation energy of this degradation is 150–200 kJ mol⁻¹.     

Simultaneous determination of chloride, nitrate and sulphate in vegetable samples by single-column ion chromatography

A new ion chromatography method is described for the simultaneous determination of Cl⁻, NO₃⁻ and SO₄²⁻, using a selected eluent 1.3-mM sodium gluconate/1.3-mM borax (pH 8.5). The extraction methods of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables are studied. The determination limits of Cl⁻, NO₃⁻, SO₄²⁻ are 0.17 μg/ml, 0.63 μg/ml and 0.81 μg/ml. The linear ranges are 060 μg/ml, 090 μg/ml and 090 μg/ml. The relative S.D. are <2.5%. The mean recoveries of Cl⁻, NO₃⁻, SO₄²⁻ in vegetables range from 97.0 to 104%.     

Enhanced sensitivity for Cu(II) by a salicylidine-functionalized polysiloxane carbon paste electrode

A new approach for decreasing the detection limit for a copper(II) ion-selective electrode (ISE) is presented. The ISE is designed using salicylidine-functionalized polysiloxane in carbon paste. This work describes the attempts to develop the electrode and measurements of its characteristics. The new type of renewable three-dimensional chemically modified electrode could be used in a pH range of 2.3–5.4, and its detection limit is 2.7 × 10⁻⁸ mol L⁻¹ (1.2 μg L⁻¹). This sensor exhibits a good Nernstian slope of 29.4 ± 0.5 mV/decade in a wide linear concentration range of 2.3 × 10⁻⁷ to 1.0 × 10⁻³ mol L⁻¹ of Cu(II). It has a short response time (8 s) and noticeably high selectivity over other Cu(II) selective electrodes. Finally, it was satisfactorily used as an indicator electrode in complexometric titration with EDTA and determination of copper(II) in miscellaneous samples such as urine and various water samples.     

Electrochemical properties of polyaniline in p-toluene sulfonic acid solution

Polyaniline was deposited potentiodynamically on a stainless steel substrate in the presence of an inorganic acids (sulfuric acid). The electrochemical characterization of the electrode was carried out by means of cyclic voltammetry and electrochemical impedance spectroscopy in the organic acids (p-toluene sulfonic acid) solution. The results show that polyaniline has a high specific capacitance of 431.8 F g⁻¹ at 1 mV s⁻¹, high coulombic efficiency of 95.6% at 20 mV s⁻¹, and exhibits a high reversibility. This indicates the promising feasibility of the polyaniline used as an electrochemical capacitor material in the electrolyte of p-toluene sulfonic acid solution especially at high charge–discharge process.     

Infrared and infrared emission spectroscopy of gallium oxide α-GaO(OH) nanostructures

Infrared spectroscopy has been used to study nano- to micro-sized gallium oxyhydroxide α-GaO(OH), prepared using a low temperature hydrothermal route. Rod-like α-GaO(OH) crystals with average length of 2.5 μm and width of 1.5 μm were prepared when the initial molar ratio of Ga to OH was 1:3. β-Ga₂O₃ nano and micro-rods were prepared through the calcination of α-GaO(OH). The initial morphology of α-GaO(OH) is retained in the β-Ga₂O₃ nanorods.The combination of infrared and infrared emission spectroscopy complimented with dynamic thermal analysis were used to characterise the α-GaO(OH) nanotubes and the formation of β-Ga₂O₃ nanorods. Bands at around 2903 and 2836 cm⁻¹ are assigned to the –OH stretching vibration of α-GaO(OH) nanorods. Infrared bands at around 952 and 1026 cm⁻¹ are assigned to the Ga–OH deformation modes of α-GaO(OH). A significant number of bands are observed in the 620–725 cm⁻¹ region and are assigned to GaO stretching vibrations.     

Cathodic electrophoretic deposition of manganese dioxide films

Cathodic electrophoretic deposition (EPD) method has been developed for the deposition of manganese dioxide films. It was shown that phosphate ester (PE) is an effective charging additive, which provides stabilization of manganese dioxide nanoparticles in suspensions. The influence of PE concentration and deposition voltage on the deposition efficiency has been studied. EPD has been utilized for the fabrication of porous nanostructured films with thickness in the range of 0.5–20 μm for application in electrochemical supercapacitors (ES). Cyclic voltammetry and chronopotentiometry data for the films tested in the 0.1 M Na₂SO₄ solutions showed capacitive behavior in the voltage window of 1 V. The highest specific capacitance (SC) of 377 F g⁻¹ was obtained at a scan rate of 2 mV s⁻¹. The SC decreased with increasing film thickness and increasing scan rate in the range of 2–100 mV s⁻¹. The deposition mechanism, kinetics of deposition and charge storage properties of the films are discussed.     

Characterization of a 10.3-μm pulsed DFB quantum cascade laser

We have measured the output parameters of a 10.3-μm pulsed distributed-feedback (DFB) quantum cascade (QC) laser manufactured by Alpes Lasers and intended for high-sensitivity detection of ammonia and ethylene. The laser beam was collimated with an AR-coated aspheric ZnSe lens with focal length of 11.6 mm and clear aperture of 16.5 mm. Near- and far-field distributions of the laser emission were recorded with an infrared imaging camera. The fast-and slow-axis laser beam divergences were measured to be 1.2 and 1.4 mrad (FWHM), respectively. The divergence was found to be increasing with injection current. An air-spaced Fabry–Perot interferometer with free spectral range of 0.05 cm⁻¹ was used to measure the frequency tuning rates of the laser. The laser was tuned by either heat sink temperature, injection current or pulse repetition rate with rates of −8 × 10⁻² cm⁻¹ K⁻¹, −7 × 10⁻² cm⁻¹ A⁻¹ and −9 × 10⁻⁴ cm⁻¹ kHz⁻¹, respectively. The laser frequency decreased linearly with a rate of 10⁻² cm⁻¹ ns⁻¹ (300 MHz ns⁻¹) for laser pulses varied from 10 to 50 ns, and the frequency chirp rate was found to decrease for longer laser pulses.     

A rapid approach for assessment of arsenic exposure by elemental analysis of single strand of hair using laser ablation-inductively coupled plasma-mass spectrometry

Application of laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) as a method for identification of arsenic in a single hair strand was investigated. Using a single point ablation method detectability of ⁷⁵As and other two elements (²⁰⁸Pb and ⁶⁴Zn) were evaluated. Arsenic (⁷⁵As) signal is improved with enhanced laser ablation conditions. For the arsenic determination in hair single spots or single linear scans with enhanced laser ablation conditions described in the paper are satisfactory although  800 μm linear scans may be preferable. Arsenic levels in a single strand of hair from individuals who were chronically exposed to arsenic contaminated drinking water from a village in the Atacama Desert in northern Chile were determined by LA-ICP-MS. These results were satisfactorily correlated with total As concentration previously measured by hydride generation (HG)-ICP-MS. The sample throughput is high and it takes  3 min per each hair sample including mounting, focusing and analysis. LA-ICP-MS method can be used for the rapid identification and screening of toxic and nutritionally important elements in hair.     

Photoacoustic infrared spectroscopy of polymer beads

Photoacoustic (PA) spectra of four types of polymer resin beads, ranging in size from 35 to 150 μm, were acquired using a Fourier transform infrared spectrometer capable of both rapid- and step-scan mirror movement. Thermal diffusion lengths were on the order of the particle sizes of the beads. The PA magnitude spectra were similar to absorption spectra; both positive- and negative-going features occurred in the phase spectra. The frequency dependences of the total PA intensities of the polymer resins and carbon black differed by a factor of about f^−0.30. The intensities of the weak bands in the ratioed spectra (resin beads/carbon black) displayed a similar dependence. Partial saturation caused a more gradual variation for the stronger bands, where the intensity is proportional to f^−0.1–f^−0.2.     

Efficient hydrogen peroxide generation from organic matter in a bioelectrochemical system

Hydrogen peroxide (H₂O₂) is an important industrial chemical, but its current production methods are highly energy-intensive. This study presents a novel process for the production of H₂O₂ based on the bioelectrochemical oxidation of wastewater organics at an anode coupled to the cathodic reduction of oxygen to H₂O₂. At an applied voltage of 0.5 V, this system was capable of producing 1.9 ± 0.2 kg H₂O₂/m³/day from acetate at an overall efficiency of 83.1 ± 4.8%. As most of the required energy was derived from the acetate, the system had a low energy requirement of 0.93 kWh/kg H₂O₂.     

Correlation between properties of a solid sample and laser-induced plasma parameters

To investigate the influence of mechanical properties of a solid sample on the laser-induced plasma parameters (temperature and mass ablated) a number of aluminum–lithium alloys and lithium ferrites with different microstructure and composition have been studied. The specific approach to estimate excitation temperature for low-resolution emission spectra has been developed. The main limitations of this approach were discussed on the basis of comparison with the energy width of several multiplets. Overall uncertainties for temperature calculation were evaluated by taking into account the accuracy of Einstein's coefficients and errors of the proposed multiplets method. The temporal evolution of laser plasma during the evaporation of these materials was studied. Extremely high value of the Li I excitation temperature has been estimated to be T > 10⁵ K for the annealed ferrite ablation, in contrast to the temperature T  1.5 · 10⁴ K for non-annealed ferrite. Only for ablation of annealed ferrite the Li II emission line at 548.4 nm was observed. It means that this laser-induced plasma was the hottest. In the case of alloys, the temperature calculated by using Li I transitions was proportional to the microhardness of the solid samples. The negative correlation between crater volume/opto-acoustic signal and alloy microhardness was observed. At the first pulses the mechanical properties of the alloys didn't correlate with the ablated mass, while the maximal correlation coefficients were observed after ablation by 10 or 50 consequent laser pulses.     

Charge transport modulation of silicon nanowire by O2 plasma

The modification of the electrical characteristics of field-effect transistors (FETs) with channels composed of n- or p-type silicon nanowires (SiNWs) by oxygen plasma treatment is investigated in this study. The SiNWs obtained from silicon bulk wafers are <111> surface-oriented and their doping concentrations are 10²¹ and 10¹⁷ cm⁻³ for the n- and p-type SiNWs, respectively. After the back-gate SiNWFETs were subjected to oxygen plasma treatment, the magnitude of the drain current of the n-type SiNWs was decreased, whereas that of the p-type SiNWs was increased, while the gate-dependent characteristics of both of types of SiNWs were improved. The changes in the electrical characteristics are due to the adsorption of oxygen ions on the surface of the SiNWs. To verify the effect of the oxygen ions, the SiNWFETs were kept in a vacuum for 24 h whereupon their electrical characteristics tended to revert to their inherent state.     

Rayleigh's distillation law and linear hypothesis of isotope fractionation in thermal ionization mass spectrometry

The relationship which exists between Rayleigh's distillation law and linear models of instrumental isotopic fractionation in thermal ionization mass spectrometry is shown. If the process of isotope fractionation in the mass spectrometer source occurs in terms of a Rayleigh's distillation, and, within the range of mass of isotopes of the element, the vapor/residue distribution coefficient is a linear function of mass with a slope which is sufficiently small in absolute value, then the linear hypothesis of isotope fractionation is fulfilled.The model shows that the fractionation factor per amu, defined as the instantaneous difference between the measured and true values of the isotope ratio, per unit of measured/true value and per unit of mass difference between the two isotopes which define the ratio, can be interpreted as a function of two parameters: the residual mass fraction of the sample on the filament, and the rate of change of the distribution coefficient with mass. These two parameters can be calculated and, in particular, the value of the residual mass fraction of the sample when the measured values of the isotopic ratios coincide with the actual values can be calculated as a function of the rate of change with mass of the distribution coefficient.A linear model of instrumental isotopic fractionation can be derived from the exponential hypothesis of fractionation, which can be also interpreted in terms of a Rayleigh's distillation process, but where mass is an exponential function of the distribution coefficient.Experimental results of instrumental isotopic fractionation (up to 1% amu⁻¹) of strontium in NIST standard reference material 987, loaded as a nitrate on a single tungsten filament, can be interpreted in terms of the linear models of isotope fractionation (and therefore of Rayleigh's distillation law) within experimental error. They show: (i) changes in the vapor/residue distribution coefficient with mass in the range −0.006 to −0.004 amu⁻¹; (ii) approximately constant rates of sample consumption in the range of residual mass fraction from 1 to 0.3–0.25, which are between 0.05 and 0.13% min⁻¹; (iii) values of the residual mass fraction of the sample, when the measured values of the isotopic ratios coincide with the true ones, between 0.3668 and 0.3671, which correspond to sample consumption of 63.3%.Since the linear hypothesis of fractionation is fulfilled, the values of isotopic ratios of strontium in the standard material can be determined. The global weighted averages of the weighted averages of the results obtained in eleven runs in which ⁸⁶Sr, ⁸⁷Sr and ⁸⁸Sr peaks were sampled are as follows: ⁸⁶Sr/⁸⁸Sr = 0.119445 ± 0.000053, ⁸⁷Sr/⁸⁶Sr = 0.71016 ± 0.00019, and ⁸⁷Sr/⁸⁸Sr = 0.084826 ± 0.000040.     

Interaction and photodynamic activity of cationic porphyrin derivatives bearing different patterns of charge distribution with GMP and DNA

The interaction of amphiphilic cationic porphyrins, containing different patterns of meso-substitution by 4-(3-N,N,N-trimethylammoniumpropoxy)phenyl (A) and 4-(trifluoromethyl)phenyl (B) groups, with guanosine 5′-monophosphate (GMP) and calf thymus DNA have been studied by optical methods in phosphate buffer solution. The properties of these synthetic porphyrins were compared with those of representative standard of anionic 5,10,15,20-tetra(4-sulphonatophenyl)porphyrin (TPPS₄⁴⁻) and cationic 5,10,15,20-tetra(4-N,N,N-trimethylammonium phenyl)porphyrin (TMAP⁴⁺). Stable complexes with GMP were found for cationic porphyrins, except for monocationic AB₃⁺. The binding constant (K_GMP  10⁴ M⁻¹) follows the order: A₃B³⁺  ABAB²⁺ > A₄⁴⁺  TMAP⁴⁺. Also, interaction with DNA was observed for all evaluated cationic porphyrins. For these related cationic porphyrins, the binding constant (K_DNA  10⁵ M⁻¹) increases with the number of cationic charges. On the other hand, the photodynamic activity of porphyrins was analyzed in solution of GMP and DNA. Monocationic AB₃⁺ is a less effective sensitizer to oxidize GMP in comparison with the other cationic porphyrins, in agreement with the lack of detected interaction with this nucleotide. The electrophoretic analysis of DNA indicates that photocleavage takes place when the samples are exposed to photoexcited tricationic and tetracationic porphyrins. In the presence of sodium azide the DNA decomposition was diminished. Also, reduction in the DNA photocleavage was observed under anoxic condition, indicating that oxygen is essential for DNA photocleavage sensitized by these cationic porphyrins. In addition, an increase in DNA degradation was not observed in deuteriated water. Therefore, an important contribution of type I photoreaction processes could be occurring in the DNA photodamage sensitized by these cationic porphyrins. These results provide a better understanding of the characteristics needed for sensitizers to produce efficient DNA photocleavage.     

Ultrafast dynamics of heat flow across molecules

An ultrafast flash thermal conductance apparatus is used to study heat flow through aliphatic and aromatic molecules arranged in self-assembled monolayers (SAMs). The apparatus consists of a thin metal film which can be flash-heated by many hundreds of degrees in 1 ps using a femtosecond pulse. Heat flow from the metal surface into the SAM molecules is detected using vibrational sum-frequency generation (SFG) spectroscopy. The SAMs studied were alkanethiolates (AT) ranging from C6 to C24, benzenethiolate (BT) and benzylmercaptide (BMT). SFG in the CH-stretch region selectively probes transitions of the terminal methyl groups of AT and the CH moiety at the 4-position of the phenyl ring of BT and BMT (opposite the thiolate-surface bond). The SFG signal is sensitive to temperature-jump induced thermal disorder of the SAM and also to vibrational frequency shifts induced by the changing intramolecular vibrational populations. The SFG probe functions as a thermometer, and this thermometer is 1.5 Å thick with a response time of 1 ps. In the AT chains, a study of the length dependence is used to determine the rate heat flows across the metal–SAM interface and the rate of heat flow through the AT chains. The interface thermal conductance is 220 GW m⁻² s⁻¹. The AT molecular conductance is 50 pW K⁻¹ or 0.3 eV s⁻¹ K⁻¹. Heat flow through the AT chains is ballistic with a velocity of 1 km/s. Heat flow into BMT is slower than in BT because BMT has one additional methylene linker group. The BT and BMT structures evidence a thermally-initiated surface rearrangement occurring in a few tens of picoseconds. These SAMs are strained and the phenyl rings cannot adopt the most stable staggered herringbone structure. After the T-jump, the SAM molecules have enough freedom to relax into more favorable configurations.     

Reduced N-methyl-pyridylethynyl porphyrins exhibit strong near-IR absorptions

Porphines bearing two N-methyl-4-pyridylethynyl substituent reversibly undergo two one-electron reductions at room temperature. The anion radicals and di-anions show diminished visible bands (450 nm and 600–700 nm) and intense absorptions in the 800-nm and 1100-nm region, respectively. Some of the near-IR bands have extinction coefficients greater than 1.5 × 10⁵ M⁻¹ cm⁻¹.     

Molecular fine structure and transition dipole moment of NO2 using an external cavity quantum cascade laser

Rotational vibrational fine structure and transition dipole moment of NO₂ is measured using Doppler free saturation spectroscopy with an external grating cavity quantum cascade laser (QCL). The QCL wavelength is calibrated using a 310 cm long internally coupled Fabry–Perot interferometer. We obtain a frequency splitting of 139.68 ± 0.06 MHz (0.0047 cm⁻¹) between the spin doublets (17) of 000 → 001 transition of NO₂. The resolution of the QCL based saturation spectrometer is limited by the QCL linewidth of 3.99 MHz ( 0.00013 cm⁻¹) deduced from the half width of the Lamb dips. The Lamb dip spectroscopy is utilized to obtain a vibrational dipole moment of 0.37 Debye for the (17) transitions.     

Enhanced tungstate electrochromism via formation of transparent conductive networks

Indium tin oxide (ITO) nanopowder was added to a polymer film containing WO₃ · H₂O particles to enhance electron conductivity and complimentary Li ion kinetics in an electrochromic device. Film conductivity increased dramatically with ITO content, suggesting the formation of conductive ITO networks in the film. The improved electron conductivity leads to a substantial increase of the effective Li⁺ ion diffusion coefficient in the composite film, from 10⁻¹¹ to 10⁻⁹ cm²/s. Electrochromic contrast studies revealed that the presence of the ITO networks leads to enhanced blue/green color contrast.