Optimization of L-Lactic acid production from glucose by Rhizopus oryzae ATCC 52311

The effect of nutrients on L(+)-lactic acid production from glucose was investigated using Rhizopus oryzae ATCC 523 11. From the shake-flask experiments, the optimal medium composition was defined for improved lactic-acid production. In order to enhance lactic-acid production rate and product yield, controlled aeration in a bubble column was conducted under optimal conditions. Results showed a maximum lactic-acid production rate of 2.58 g/L/h was obtained with an initial glucose concentration of 94 g/L. Finallactic-acid concentration of 83 g/L was achieved after 32 h of fermentation with a weight of 0.88 glactic acid/g glucose consumed.     

Characterization of a high-productivity recombinant strain of Zymomonas mobilis for ethanol production from glucose/xylose mixtures

The fermentation characteristics of a recombinant strain of Zymomonas mobilis ZM4(pZB5) capable of converting both glucose and xylose to ethanol have been further investigated. Previous studies have shown that the strain ZM4(pZB5) was capable of converting a mixture o 65 g/L of glucose and 65 g/L of xylose to 62 g/L of ethanol in 48 h with an overall yield of 0.46 g/g. Higher sugar concentrations (e.g., 75/75 g/L) resulted in incomplete xylose utilization (80 h). In the present study, further kinetic evaluations at high sugar levels are reported. Acetate inhibition studies and evaluation of temperature and pH effects indicated increased maximum specific uptake rates of glucose and xylose under stressed conditions with increased metabolic uncoupling. A high-productivity system was developed that involved a membrane bioreactor with cell recycling. At sugar concentrations of approx 50/50 g/L of glucose/xylose, an ethanol concentration of 50 g/L, an ethanol productivity of approx 5 g/(L·h), and a yield (Y _p/s) of 0.50 g/g were achieved. Decreases in cell viability were found in this system after attainment of an initial steady state (40–60 h); a slow bleed of concentrated cells may be required to overcome this problem.     

Activity of xylose reductase from Candida mogii grown in media containing different concentrations of rice straw hydrolysate

Xylose reductase (XR) activity was evaluated in extracts of Candida mogii grown in media containing different concentrations of rice straw hydrolysate. Results of X Ractivity were compared to xylitol production and a similar behavior was observed for these parameters. Highest values of specific production and productivity were found for xylose reductase (35 U/g of cell and 0.97 U/[g of cell·h], respectively) and for xylitol (5.63 g/g of cell and 0.13 g/[g of cell·h]) in fermentation conducted in medium containing 49.2 g of xylose/L. The maximum value of XR:XD ratio (1.82) was also calculated under this initial xylose concentration with 60 h of fermentation.     

Ethanol production in immobilized-cell bioreactors from mixed sugar syrups and enzymatic hydrolysates of steam-exploded biomass

We investigated ethanol production from mixed sugar syrups. Hydrolysates were prepared from enzymatic saccharification of steam-pretreated aspen chips. Syrups containing 45 g/L of glucose and 12 g/L of xylose were detoxified through two ion-exchange resins and then fermented with Pichia stipitis and Saccharomyces cerevisiae immobilized in Ca-alginate gel beads. Combinations of different gel fractions in the fermentation volume, amount of yeast cells, and ratios of P. stipitis vs S. cerevisiae within each bead were compared. In the best conditions, by using a total beads volume corresponding to 25% of the working volume, we obtained a yield of 0.39 g_ethanol/g_{initial sugars}. This amount of gel entrapped an initial cell concentration of 6×10¹²cells/L with ratio of S. cerevisiae/P. stipitis of 0.25 g/g. Modified stirredtank reactors were obtained either by adding marbles or by inserting a perforated metal cylinder, which reduced considerably the rupture of beads while visibly improving oxygenation of the medium.     

Production of biosurfactant from a new and promising strain of Pseudomonas aeruginosa PA1

The Pseudomonas aeruginosa PA1 strain, isolated from the water of oil production in Sergipe, Northeast Brazil, wasevaluated as a potential rhamnolipid type of biosurfactant producer. The production of biosurfactants was investigated using different carbon sources (n-hexadecane, paraffin oil, glycerol, and babassu oil) and inoculum concentrations (0.0016–0.008 g/L) The best results were obtained with glycerol as the substrate and an initial cell concentration of 0.004 g/L. AC:N ratio of 22.8 led to the greatest production of rhamnolipids (1700 mg/L) and efficiency (1.18 g of rhamnolipid/g of dry wt).     

Xylose reductase production by candida guilliermondii

The effect of pH, time of fermentation, and xylose and glucose concentration on xylitol production, cell growth, xylose reductase (XR), and xylitol dehydrogenase (XD) activities ofCandida guilliermondii FTI 20037 were determined. For attaining XR and XD activities of 129-2190 U/mg of protein and 24-917 U/mg of protein, respectively, the cited parameters could vary as follows: initial pH: 3.0-5.0; xylose: 15-60 g/L; glucose: 0-5 g/L; and fermentation time: 12-24 h. Moreover, the high XR and XD activities occurred when the xylitol production by the yeast was less than 19.0 g/L.     

Production of propionic acid using a xylose utilizingPropionibacterium

The kinetics ofP. acidipropionici (ATCC25562), a xylose-utilizing rumen microorganism, was studied to assess its use for propionic acid production from wood hydrolyzates. Propionic acid has been shown to have a stronger inhibitory effect than acetic acid, with the undissociated acid form being responsible for the majority of the inhibitory effect. Thus, in batch tests with pH controlled at 6.0, the propionic acid concentration reaches 25 g/L and the acetic acid 7 g/L. Xylose uptake rate is dependent on the specific growth rate and glucose concentration. An immobilized cell columnar reactor at very high product yields (80%) proved adequate for propionic production. At cell concentrations of 95 g/L with high product concentration, volumetric productivities of 2.7 g/L·h were obtained in ultrafiltration cell recycle systems.     

Continuous production of lactic acid in a cell recycle reactor

The production of lactic acid from glucose has been demonstrated using a CSTR (continuous stirred-tank reactor) with cell recycle. Studies were conducted withLactobacillus delbrueckii at a fermentation temperature of 42°C and a pH of 6.25. A cell density of 140 g dry weight/L and a volumetric productivity of 150 g/L.h, with complete glucose consumption, were obtained. It was not possible to obtain a lactic acid concentration above 60 g/L because of product inhibition. A cell purge was not necessary to maintain high viability bacteria culture or to obtain a steady state. At steady state the net cell growth appeared to be negligible. The specific glucose consumption for cell maintenance was 0.33 g glucose/g cells-h.     

Oxygen uptake rate in production of xylitol by Candida guilliermondii with different aeration rates and initial xylose concentrations

The global oxygen uptake rate (OUR) and specific oxygen uptake rates (SOUR) were determined for different values of the volumetric oxygen mass transfer coefficient (15, 43, and 108 h⁻¹), and for varying initial xylose concentrations (50, 100, 150, and 200 g/L) in shaking flasks. The initial cell concentration was 4.0 g/L, and there was only significant growth in the fermentation with the highest oxygen availability. In this condition, OUR increased proportionally to cell growth, reaching maximum values from 2.1 to 2.5 g of O₂/(L·h) in the stationary phase when the initial substrate concentration was raised from 50 to 200 g/L, respectively. SOUR showed different behavior, growing to a maximum value coinciding with the beginning of the exponential growth phase, after which point it decreased. The maximum SOUR values varied from 265 to 370 mg of O₂/(g of cell·h), indicating the interdependence of this parameter and the substrate concentration. Although the volumetric productivity dropped slightly from 1.55 to 1.18 g of xylitol/(L·h), the strain producing capacity (γ _P/X ) rose from 9 to 20.6 g/g when the initial substrate concentration was increased from 50 to 200 g/L. As for the xylitol yield over xylose consumed (γ _P/S ), there was no significant variation, resulting in a mean value of 0.76 g/g. The results are of interest in establishing a strategy for controlling the dynamic oxygen supply to maximize volumetric productivity.     

Production of l-malic acid via biocatalysis employing wild-type and respiratory-deficient yeasts

Succinic acid was produced efficiently from fumaric acid by a recombinantE. coli strain DH5αt/pGC1002 containing multicopy fumarate reductase genes. The effects of initial fumaric acid and glucose concentration on the production of succinic acid were investigated. Succinic acid reached 41 to over 60 g/L in 48.5 h starting with 50 to 64 g/L fumaric acid. Significant substrate inhibition was observed at initial fumaric acid concentration of 90 g/L. L-Malic acid became the major fermentation product under these conditions. Provision of glucose (5-30 g/L) to the fermentation medium stimulated the initial succinic acid production rate over two folds.     

Biosurfactant production by Rhodococcus erythropolis grown on glycerol as sole carbon source

The production of biosurfactant by Rhodococcus erythropolis during the growth on glycerol was investigated. The process was carried out at 28°C in a 1.5-L bioreactor using glycerol as carbon source. The bioprocess was monitored through measurements of biosurfactant concentration and glycerol consumption. After 51 h of cultivation, 1.7 g/L of biosurfactant, surface, and interfacial tensions values (with n-hexadecane) of 43 and 15 mN/m, respectively, 67% of Emulsifying Index (E ₂₄), and 94% of oil removal were obtained. The use of glycerol rather than what happens with hydrophobic carbon source allowed the release of the biosurfactant, originally associated to the cell wall.     

Bioconversion of fumarate to succinate using glycerol as a carbon source

In this study, a facultative bacterium that converts fumarate to succinate at a high yield was isolated. The yield of biocon version was enhanced about 1.2 times by addition of glucose into culture medium at an initial concentration of 6 g/L. When the initial cell density was high (2 g/L), the succinate produced at pH 7.0 for initial fumarate concentrations of 30, 50, 80, and 100 g/L were 29.3, 40.9, 63.6, and 82.5 g/L, respectively, showing an increase with the initial fumarate concentration. The high yield of 96.8%/mole of fumarate in just 4 h was obtained at the initial fumarate concentration of 30 g/L. Comparing these values to those obtained with low cell culture (0.2 g/L), we found that the amount of succinate produced was similar, but the production rate in the high cell culture was about three times higher than was the case in the low cell culture. This strain converted fumarate to succinate at a rate of 3.5 g/L·h under the sparge of CO₂.     

Xanthan gum production from cassava bagasse hydrolysate with Xanthomonas campestris using alternative sources of nitrogen

Cassava bagasse was hydrolyzed using HCl and the hydrolysate was used for the production of xanthan gum using a bacterial culture of Xanthomonas campestris. Cassava bagasse hydrolysate with an initial concentration of approx 20 g of glucose/L proved to be the best substrate concentration for xanthan gum production. Among the organic and inorganic nitrogen sources tested to supplement the medium—urea, yeast extract, peptone, potassium nitrate, and ammonium sulfate—potassium nitrate was most suitable. Ammonium sulfate was the least effective for xanthan gum production, and it affected sugar utilization by the bacterial culture. In media with an initial sugar concentration of 48.6 and 40.4 g/L, at the end of fermentation about 30 g/L of sugars was unused. Maximum xanthan gum (about 14 g/L) was produced when fermentation was carried out with a medium containing 19.8 g/L of initial reducing sugars supplemented with potassium nitrate and fermented for 72 h, and it remained almost the same until the end of fermentation (i.e., 96 h).     

Biosynthesis of poly-β-hydroxybutyrate and exopolysaccharides on azotobacter chroococcum strain 6B utilizing simple and complex carbon sources

Coproduction of poly-β-hydroxybutyrate (PHB) and exopolysaccharides (EPS) was investigated with Azotobacter chroococcum strain 6B isolated from soil samples. The bacterium was cultured using various carbon sources solely or with 0.1 g/L of ammonium sulfate. Ammonium addition resulted in reduced PHB and EPS production with glucose, fructose, and sucrose media, but cellular mass remained constant except for sucrose. Protein was nearly twofold higher in ammonium-grown cultures. Glucose and fructose alone biosynthesized high amounts of EPS (maximum 2.1 and 1.1 g/L, respectively, at 72 h), whereas PHB was accumulated only in glucose-grown cells. Sucrose almost did not produce EPS. Conversely, PHB content was the highest obtained from all experimented conditions (1.1 g/L at 48 h, 40% cell dry wt). When a complex carbon source such as sugar cane molasses was utilized, PHB was accumulated concomitant with EPS production from the initial time to 48 h (0.75 g/L, 37% cell dry wt and 0.6 g/L, respectively), and then PHB decayed at 72 h (0.2 g/L). On the other hand, EPS continued to be biosynthesized (1.1 g/L, 72 h). PHB fractions of total intra- and extracellular biopolymers were calculated. Sucrose-modified Burk’s medium without ammonium addition is suggested as a medium capable of diverting the carbon source for the production of intracellular PHB rather than EPS with A. chroococcum 6B.     

Continuous production of succinic acid by a fumarate-reducing bacterium immobilized in a hollow-fiber bioreactor

Enterococcus faecalis RKY1, a fumarate-reducing bacterium, was immobilized in an asymmetric hollow-fiber bioreactor (HFBR) for the continuous production of succinic acid. The cells were inoculated into the shell side of the HFBR, which was operated in transverse mode. Since the pH values in the HFBR declined during continuous operation to about 5.7, it was necessary to change the feed pH from 7.0 to 8.0 after 24 h of operation in order to enhance production of succinic acid. During continuous operation with a medium containing fumarate and glycerol, the productivity of succinate was 3.0–10.9 g/(L·h) with an initial concentration of 30 g/L of fumarate, 4.9–14.9 g/(L·h) with 50 g/L of fumarate, and 7.2–17.1 g/(L·h) with 80 g/L of fumarate for dilution rates between 0.1 and 0.4 h⁻¹. The maximum productivity of succinate obtained by the HFBR (17.1 g of succinate /[L·h]) was 1.7 times higher than that of the batch bioconversions (9.9 g of succinate /[L·h]) with 80 g/L of fumarate. Furthermore, the long-term stability of the HFBR was demonstrated with a continuously efficient production of succinate for more than 15 d (360 h).     

Improvement of inulin hydrolysis yeast cell reactor by mutants selection

In a previous publication, we described a continuous production ofd-fructose from enzymatic hydrolysis of inulin with immobilized permeabilized cells (1).Kluyveromyces fragilis ATCC 12424 have been shown to possess inulase activity. The half life of the reactor was at least 1300 h, but productivity was relatively low (around 40 g/L/day). A selection of 50 mutants was tested on liquid medium for a possible increase of productivity. In relation to the improvement of the reactor, the most important factor is intracellular inulase activity, and this activity was increased with the KF 28 mutant. Productivity reached 2000 g/L/day with the increase (of the productivity), proportional to the increase of intracellular inulase activity.     

Effect of starting xylose concentration on the microaerobic metabolism of Debaryomyces hansenii: the use of carbon material balances

Xylitol production by Debaryomyces hansenii NRRL Y-7426 was performed on synthetic medium varying the initial xylose concentration between 50 and 300 g/L. The experimental results of these tests were used to investigate the effect of substrate level on xylose consumption by this yeast. Satisfactory values of product yield on substrate (0.74–0.83 g/g) as well as volumetric productivity (0.481–0.694 g/L·h) were obtained over a wide range of xylose levels (90–200 g/L), while a worsening of kinetic parameters took place at higher concentration, likely due to a substrate inhibition phenomenon. The metabolic behavior of D. hansenii was studied, under these conditions, through a carbon material balance to estimate the fractions of xylose consumed by the cell for different activities (xylitol production, biomass growth, and respiration) during the lag, exponential, and stationary phases.     

Lactic acid production through cell-recycle repeated-batch bioreactor

The effect of various nitrogen sources on cell growth and lactic acid production was investigated. The most effective nitrogen source was yeast extract; more yeast extract gave higher cell growth and lactic acid productivity. Yeast extract dosage and cell growth were proportional up to a yeast extract concentration of 30 g/L, and lactic acid productivity was linearly correlated up to a yeast extract dosage of 25 g/L. However, increasing the yeast extract content raises the total production cost of lactic acid. Therefore, we attempted to find the optimum yeast extract dosage for a repeated-batch operation with cell recycling. The results show that when using Enterococcus faecalis RKY1 only 26% of the yeast extract dosage for a conventional batch fermentation was sufficient to produce the same amount of lactic acid, whereas the lactic acid concentration in the product stream (92–94 g/L) and lactic acid productivity (6.03–6.20 g/[L·h]) were similar to those of a batch operation. Furthermore, long-term stability was established.     

High-Cell-Density cultivation of pseudomonas putida IPT 046 and medium-chain-length polyhydroxyalkanoate production from sugarcane carbohydrates

We studied high-density cultures of Pseudomonas putida IPT 046 for the production of medium-chain-length polyhydroxyalkanoates (PHA_MCL) using an equimolar mixture of glucose and fructose as carbon sources. Kinetics studies of P. putida growth resulted in a maximum specific growth rate of 0.65h⁻¹. Limitation and inhibition owing to NH₄ ⁺ ions were observed, respectively, at 400 and 3500 mg of NH₄ ⁺/L. The minimum concentration of dissolved oxygen in the broth must be 15% of saturation. Fed-batch strategies for high-cell-density cultivation were proposed. Pulse feed followed by constant feed produced a cell concentration of 32 g/L in 18 h of fermentation and low PHA_MCL content. Constant feed produced a cell concentration of 35 g/L, obtained in 27 h of fermentation, with up to 15% PHA_MCL. Exponential feed produced a cell concentration of 30 g/L in 20 h of fermentation and low PHA_MCL content. Using the last strategy, 21% PHA_MCL was produced during a period of 34 h of fed-batch operation, with a final cell concentration of 40 g/L and NH₄ ⁺ limitation. Using phosphate limitation, 50 g/L cell concentration, 63% PHA_MCL and a productivity of 0.8 g/(L·h) were obtained in 42 h of fed-batch operation. The PHA_MCL yield factors from consumed carbohydrate for N-limited and P-limited experiments were, respectively, 0.15 and 0.19 g/g.     

Optimization of inulinase production by Kluyveromyces marxianus using factorial design

Factorial design and response surface techniques were used to optimize the culture medium for the production of inulinase by Kluyveromyces marxianus. Sucrose was used as the carbon source instead of inulin. Initially, a fractional factorial design (2^5–1) was used in order to determine the most relevant variables for enzyme production. Five parameters were studied (sucrose, peptone, yeast extract, pH, and K₂HPO₄), and all were shown to be significant. Sucrose concentration and pH had negative effects on inulinase production, whereas peptone, yeast extract, and K₂HPO₄ had positive ones. The pH was shown to be the most significant variable and should be preferentially maintained at 3.5. According to the results from the first factorial design, sucrose, peptone, and yeast extract concentrations were selected to be utilized in a full factorial design. The optimum conditions for a higher enzymatic activity were then determined: 14 g/L of sucrose, 10 g/L of yeast extract, 20 g/L of peptone, 1 g/L of K₂HPO₄. The enzymatic activity in the culture conditions was 127 U/mL, about six times higher than before the optimization.