Molecular electrodes at the exposed edge of metal/insulator/metal trilayer structures

Producing reliable electrical contacts of molecular dimensions has been a critical challenge in the field of molecule-based electronics. Conventional thin film deposition and photolithography techniques have been utilized to construct novel nanometer-sized electrodes on the exposed vertical plane on the edge of a thin film multilayer structure (metal/insulator/metal). Via thiol surface attachment to metal leads, an array of paramagnetic, cyanide-bridged octametal complexes, [(pzTp)FeIII(CN)3]4[NiII(L)]4[O3SCF3]4 (1) [(pzTp) = tetra(pyrazol-1-yl)borate; L = 1-S(acetyl)tris(pyrazolyl)decane], were covalently linked onto the electrodes forming a dominant conduction pathway. A series of molecule-based devices were fabricated using Ni, NiFe, Ta, and Au as metal electrodes separated by insulating Al2O3 spacers, followed by treatment with 1. A series of control experiments were also performed to demonstrate that the conduction path was through tethered metal clusters. The molecular current was analyzed via the Simmons tunnel model, and calculations are consistent with electron tunneling through the alkane ethers to the central metal core. With a Ni/Al2O3/Au molecular electrode, the tether binding was found to be reversible to the top Au layer, allowing for a new class of chemical detection based on the steric bulk of coordinating analytes to disconnect the molecular current path. Simple and economical photolithography/liftoff/self-assembly fabrication techniques afford robust molecular junctions with high reproducibility (>90%) and long operational lifetimes (>1 year).     

Fabrication and characterization of metal-molecule-metal junctions by conducting probe atomic force microscopy

Metal-molecule-metal junctions were fabricated by contacting Au-supported alkyl or benzyl thiol self-assembled monolayers (SAMs) with an Au-coated atomic force microscope (AFM) tip. The tip-SAM microcontact is approximately 15 nm(2), meaning the junction contains approximately 75 molecules. Current-voltage (I-V) characteristics of these junctions were probed as a function of SAM thickness and load applied to the microcontact. The measurements showed: (1) the I-V traces were linear over +/-0.3 V, (2) the junction resistance increased exponentially with alkyl chain length, (3) the junction resistance decreased with increasing load and showed two distinct power law scaling regimes, (4) resistances were a factor of 10 lower for junctions based on benzyl thiol SAMs compared to hexyl thiol SAMs having the same thickness, and (5) the junctions sustained fields up to 2 x 10(7) V/cm before breakdown. I-V characteristics determined for bilayer junctions involving alkane thiol-coated tips in contact with alkane thiol SAMs on Au also showed linear I-Vs over +/-0.3 V and the same exponential dependence on thickness. The I-V behavior and the exponential dependence of resistance on alkyl chain length are consistent with coherent, nonresonant electron tunneling across the SAM. The calculated conductance decay constant (beta) is 1.2 per methylene unit ( approximately 1.1 A(-)(1)) for both monolayer and bilayer junctions, in keeping with previous scanning tunneling microscope and electrochemical measurements of electron transfer through SAMs. These measurements show that conducting probe-AFM is a reliable method for fundamental studies of electron transfer through small numbers of molecules. The ability to vary the load on the microcontact is a unique characteristic of these junctions and opens opportunities for exploring electron transfer as a function of molecular deformation.     

Nanoscale measurements of conducting domains and current-voltage characteristics of chemically deposited polyaniline films

Spatial variations in electric conductivity and evolutions of band structures of polyaniline (PANI) films have been studied by use of a so-called current-sensing atomic force microscope (CS-AFM) or atomic force microscope current image tunneling spectroscopy (AFM-CITS). PANI films were deposited chemically onto indium-tin oxide- (ITO-) glass substrates, and their thickness and doping levels were controlled by polymerization and acid-doping conditions. The conducting uniformity of the PANI films depends on their doping level and thickness. Conducting domains were observed in fully doped PANI film, even when the bias voltage was reduced to as small as 30 mV. High current flowing regions gradually disappeared when conducting PANI films were partially dedoped. The point-contact current-voltage (I-V) characteristics of conducting tip-polymer/ITO systems were investigated on PANI films with different thickness and degree of doping. Various types of I-V curves representing metallic, semiconducting, and insulating states were obtained depending on the aggregation of polymer chains and doping level of the polymer film. The band gap energies (estimated from the I-V or dI/dV-V curves) of emeraldine base (EB) (undoped polyaniline) films are all higher than 3.8 eV, and a wide distribution of the band gap energies (0-1.1 eV and 0.75-1.8 eV for fully and partially doped PANI thin films, respectively) was found in a single polymer film.     

Correlation between HOMO alignment and contact resistance in molecular junctions: aromatic thiols versus aromatic isocyanides

Understanding electron transport in metal-molecule-metal (MMM) junctions is of great importance for the advancement of molecular electronics. Critical factors that determine conductivity in a MMM junction include the nature of metal-molecule contacts and the electronic structure of the molecular backbone. We have studied the electronic transport property and the valence electronic structure on rigid, conjugated oligoacenes of increasing length with either thiol (-S) or isocyanide (-CN) linkers using conducting probe atomic force microscopy (CP-AFM) and ultraviolet photoelectron spectroscopy (UPS). We find that for these conjugated systems the Au-CN contact is more resistive than Au-S. The difference in contact resistance correlates with UPS measurements that show the highest-occupied molecular orbital (HOMO) of the isocyanide series is lower in energy (relative to the Fermi level of Au) than the HOMO of the thiol series, indicating the presence of a higher tunneling barrier at the contact for the isocyanide-linked molecules. By contrast, the difference in the HOMO positions for the two series of molecules does not appear to affect the length dependence of the junction resistance (i.e., the beta value = 0.5 A-1).     

First Principle Study on the Rectification of Molecular Junctions Based on the Thiol-ended Oligosilane

The electron transport properties of various molecular junctions based on the thiol-ended oligosilane are investigated through density functional theory combined with non-equilibrium Green's function formalism. Our calculations show that oligosilanes doped by the phenyl and-C10H6 groups demonstrate better rectifying effect and their rectification ratios are up to 15.41 and 65.13 for their molecular junctions. The current-voltage(I-V) curves of all the Au/ modified oligosilane/Au systems in this work are illustrated by frontier molecular orbitals, transmission spectra and density of states under zero bias. And their rectifying behaviors are analyzed through transmission spectra.     

Electrochemical fabrication of metal/organic/metal junctions for molecular electronics and sensing applications

A simple electrochemical approach was used for fabricating electrode/metal nanowire/(molecule or polymer)/electrode junctions for sensing or molecular electronics applications. The procedure for fabricating these molecule-based devices involves electropolymerization of phenol or chemisorption of alkanethiols on one set of electrodes (E1) and electrodeposition of Ag metal nano/microwires on a second electrode (E2) which is ～5 μm away from E1. Under appropriate deposition conditions, Ag nanowires grow from E2 and cross over to E1, forming a E1/(molecule or polymer)/Ag nanowire (NW)/E2 junction. The junction resistance was controlled by (1) electrodepositing polyphenol of varied densities on E1 and (2) assembling alkanethiols of different chain lengths on E1. Ag NWs at high resistance E1/polyphenol/Ag NW/E2 junctions functionalized with Pd monolayer protected clusters (MPCs) responded fast and reversibly to H(2) concentrations as low as 0.11% in a nitrogen carrier gas by a resistance decrease, likely due to volume expansion of the Pd nanoparticles, demonstrating the use of these electrochemically fabricated junctions for gas sensing applications.     

LEED, STM, and TDS studies of ordered thin films of the rhombus-shaped polycondensed aromatic hydrocarbon C54H22, on MoS2, GeS, and graphite

Low-energy electron diffraction (LEED), scanning tunneling microscopy (STM), and thermal desorption spectroscopy (TDS) are used to study vacuum vapor-deposited molecular thin films of the rhombus-shaped polycondensed aromatic hydrocarbon "rhombus-C54", C54H22, on MoS2 and graphite (0001) and on GeS (010) substrates. It is found that this compound forms well-ordered incommensurate superstructures of the closest packed flat-lying molecules in well-defined azimuthal orientations to the substrate. These films are thermally remarkably stable. By TDS, a monolayer binding energy on graphite of 2.3 eV was derived, whereas the molecules in the second layer were found to be less strongly bound (1.9 eV). This difference allows the preparation of monolayers by desorbing multilayers at the appropriate temperature. Apparently, this molecule is a promising candidate for further studies aiming at applications in organic electronics such as organic field effect transistors or light emitting displays.     

Theoretical studies of electron transport in thiophene dimer: effects of substituent group and heteroatom

The electron-transport properties of various substituted molecules based on the thiol-ended thiophene dimer (2Th1DT) are investigated through density functional theory (DFT) combined with nonequilibrium Green's function (NEGF) method. The current-voltage (I-V) curves of all the Au/2Th1DT/Au systems in this work display similar steplike features, while their equilibrium conductances show a large difference and some of these I-V curves are asymmetric distinctly. The results reveal the dependence of conductance on the energy level of the substituted 2Th1DT molecules. Rectification ratios are computed to examine the asymmetric properties of the I-V curves. The rectifying behavior in the 2Th1DT molecule containing the amino group close to the molecular end is more prominent than that in the other molecules. The rectifying behavior is analyzed through transmission spectra and molecular projected self-consistent Hamiltonian (MPSH) states. Slight negative differential resistance (NDR) can be observed in some of the systems. The electron-transport properties of 2Th1DT molecules containing different heteroatoms are also investigated. The results indicate that the current in heteroatom-containing molecules is larger than that in their pristine analogues, and lighter heteroatoms are more favorable than heavier heteroatoms for electron transport of the thiophene dimer.     

Reflection anisotropy spectroscopy study of the adsorption of sulfur-containing amino acids at the Au(110)/electrolyte interface

Protein interactions with surfaces are key to understanding the behavior of implantable medical devices. The optical technique of reflection anisotropy spectroscopy (RAS) has considerable potential for the study of interactions between important biological molecules and surfaces. This study used RAS to investigate the adsorption of S amino acids onto Au(110) in a liquid environment under different conditions of potential and pH. Certain spectral features can be associated with the Au(110), as reported previously, while other features are assigned to bonds between the amino acids and the Au surface. The RA spectra are shown to be influenced by the structure of the amino acid, the solution pH, and the applied electrode potential. This work has assigned the negative feature at 2.5 eV to the Au-thiolate, bond while the positive feature at 2.5 eV is assigned to the disulfide bond. The broad spectral feature at 3.5 eV is attributed to the Au-amino interaction, while the sharper feature at slightly higher energy is associated with the Au-carboxylate interaction. Sulfur-containing amino acids are frequently found on the outside of protein molecules and could be used to anchor the protein to the surface.     

Effects of polymerization media on the nanoscale conductivity and current-voltage characteristics of chemically synthesized polyaniline films

A current sensing atomic force microscope (CS-AFM) was used to probe the conducting homogeneity and band structures of fully doped polyaniline (PANI) films prepared from in situ chemical polymerization/deposition of aniline on indium tin oxide in various inorganic acids. The charge transport properties of PANI films depend on the film thickness as well as polymerization medium. Fluctuations in conductivity are observed on all acid-doped PANI films and the conducting homogeneity was dependent on the film thickness: the conductivity of thick film is more uniform. The current-voltage (I-V) characteristics of all thick (>200 nm) films displayed a metal-like behavior and conductivity as high as 40 S/cm was detected in high conducting regions of film thicker than 400 nm. Whereas thin (<120 nm) films revealed insulating, semiconducting, and semimetal conducting, wide distribution in conductivity and interband distances (estimated from the I-V ordI/dV-V curves) was found. The interband distances is 0-1.35, 0-1.0, and 0-0.78 eV for thin PANI film prepared from HCl(aq), HClO(4)(aq), and H2SO4(aq), respectively. PANI film (260 nm) prepared from H2SO4(aq) revealed fiberlike morphology, and compared to PANI films prepared from HCl(aq) and HClO4(aq) with similar thickness, it has higher average nanoscale conductivity but lower bulk conductivity. This result could be direct evidence which supports that the bulk conductivity of PANI depended on the carriers hopping between the conducting domains.     

旋涂水溶液前驱体制备氧化锌薄膜及其性质

通过旋涂法, 采用Zn(OAc)2·2H2O和聚环氧乙烷(PEO)的水溶液为前驱体在不同的热处理温度下制备了ZnO薄膜. PEO的加入增加了溶液的成膜性, 其较低的热分解温度有利于制得纯净的ZnO薄膜. 文中考察了在不同热处理温度下制备的ZnO薄膜的形貌、结晶性、带隙(Eg)以及电导性. 原子力显微镜(AFM)测试表明在热处理温度为400、450和500 ℃制备的ZnO薄膜的粗糙度均方根值分别为3.3、2.7和3.6 nm. 采用透射电子显微镜(TEM)测试发现ZnO薄膜中含有大量纳晶粒子. 通过测试ZnO薄膜的UV-Vis吸收光谱, 根据薄膜位于373 nm处的吸收带边计算得到ZnO的带隙为3.3 eV. 通过对薄膜的电流-电压(I-V)曲线的测试计算得到在热处理温度为400、450和500 ℃制备的ZnO薄膜的电阻率分别为3.3×109、2.7×109和6.6×109 Ω·cm. 450 ℃时制备的ZnO薄膜的电阻率最小, 主要是由于较高的热处理温度有利于提高薄膜的纯度、密度和吸附氧. 而纯度较高、密度较大的薄膜电阻率比较小; 吸附氧含量增加, 晶界势垒增大, 电阻率增大. 因此在纯度和吸附氧的双重作用下450 ℃时制备的ZnO薄膜的电阻率最小, 而500 ℃时制备的ZnO薄膜的电阻率最大.     

Linker dependent bond rupture force measurements in single-molecule junctions

We use a modified conducting atomic force microscope to simultaneously probe the conductance of a single-molecule junction and the force required to rupture the junction formed by alkanes terminated with four different chemical link groups which vary in binding strength and mechanism to the gold electrodes. Molecular junctions with amine, methylsulfide, and diphenylphosphine terminated molecules show clear conductance signatures and rupture at a force that is significantly smaller than the measured 1.4 nN force required to rupture the single-atomic gold contact. In contrast, measurements with a thiol terminated alkane which can bind covalently to the gold electrode show conductance and force features unlike those of the other molecules studied. Specifically, the strong Au-S bond can cause structural rearrangements in the electrodes, which are accompanied by substantial conductance changes. Despite the strong Au-S bond and the evidence for disruption of the Au structure, the experiments show that on average these junctions also rupture at a smaller force than that measured for pristine single-atom gold contacts.     

Optical band gap and conductivity measurements of polypyrrole-chitosan composite thin films

Electrical conductivity and optical properties of polypyrrole-chitosan（PPy-CHI） conducting polymer composites have been investigated to determine the optical transition characteristics and energy band gap of composite films.The two electrode method and I-V characteristic technique were used to measure the conductivity of the PPy-CHI thin films,and the optical band gap was obtained from their ultraviolet absorption edges.Depending upon experimental parameter,the optical band gap（E_g） was found within 1.30-2.32 eV as estimated from optical absorption data.The band gap of the composite films decreased as the CHI content increased.The room temperature electrical conductivity of PPy-CHI thin films was found in the range of 5.84×10^-7-15.25×10^-7 S·cm^-1 depending on the chitosan content.The thermogravimetry analysis（TGA） showed that the CHI can improve the thermal stability of PPy-CHI composite films.     

STM study of morphology and electron transport features in cytochrome c and nanocluster molecule monolayers.

The morphology and electron tunneling through single cytochrome c and nanocluster Pt(5)(CO)(7)[P(C(6)H(5))](4) molecules organized as monolayer Langmuir-Blodgett (LB) films on graphite substrate have been studied experimentally using scanning tunneling microscopy (STM) and spectroscopy techniques with sub-nanometer spatial resolution in a double barrier tunnel junction configuration STM tip-monomolecular film-conducting substrate at ambient conditions. STM images of the films revealed globular structures with characteristic diameters (approximately 3.5 nm for the protein molecule and approximately 1.2 nm for the nanocluster). The spectroscopic study by recording the tunneling current-bias voltage (I-V) curves revealed tunneling I-V characteristics with features as steps of different width and heights that are dependent on the STM tip position over the molecule in the monolayer, giving evidence for sequential discrete electron-tunneling effects with the combination of the single electron Coulomb-charging energy and the electronic energy level separation (molecular spectrum) in such immobilized metalloprotein and nanocluster structures that can be of interest for the development of bioelectronic and hybrid functional nanosystems.     

Amperometric Detection and Quantification of 8‐Hydroxy‐2′‐deoxyguanosine (8‐OHdG) Using Dendrimer Modified Electrodes

8‐Hydroxy‐2′‐deoxyguanosine (8‐OHdG) detection by high performance liquid chromatography (HPLC) with amperometric detection was studied using a Au electrode modified with different dendrimer based thin films. Gold electrode is thiol‐modified, forming self‐assembled monolayers on which different generation PAMAM dendrimers with terminal functional groups ? COOH and ? NH₂ have been attached using peptidic bonds. Results obtained in synthetic samples show low limits of detection and quantification for 8‐OHdG (1.2×10^?9 and 3.7×10^?9 M respectively), with matrix interference elimination, thus avoiding sample pretreatment. Best results are obtained with electrodes modified with aliphatic amino thiols and 3.5 and 4.5 generation carboxylated dendrimers (Au/AET/DG^3.5 and Au/AET/DG^4.5), demonstrating that these materials constitute a good alternative for 8‐OHdG determination in biological fluids.     

Ion transport in mesoporous silica SBA-16 thin films with 3D cubic structures

Mesoporous silica SBA-16 thin films with highly ordered 3D cubic structures were synthesized on a Si substrate via the dip-coating method. After these films were filled with KCl aqueous solutions, the ionic current passing through the mesopores was measured by applying dc electric fields. At low ion concentrations, the measured I-V curves were nonlinear and the current increased exponentially with respect to voltage. As the ion concentration increased, the I-V curve approached linear behavior. The nonlinear behavior of I-V curves can be reasonably attributed to the electric potential barrier created in nanopores.     

The influence of electrode metals and its configuration on the response of tin oxide thin film CO sensor

Thin films of tin oxide were deposited by electron beam evaporation. The effects of the electrode materials (Ag, Al, Au and Pt) and different electrode configurations on the CO-sensing of tin oxide thin films were investigated. The Pt and Au electrodes with bottom electrode configuration show much higher response than Ag and Al electrodes. The sensor response and recovery times have also been measured. The films were characterized using X-ray diffraction and X-ray photoelectron spectroscopy. All the films were found to be amorphous. It was found that the CO-sensing properties depend both on the electrode materials and configuration.     

Conformations and charge transport characteristics of biphenyldithiol self-assembled-monolayer molecular electronic devices: a multiscale computational study

We report a computational study of conformations and charge transport characteristics of biphenyldithiol (BPDT) monolayers in the (sqrt.3 x sqrt.3)R30 degrees packing ratio sandwiched between Au(111) electrodes. From force-field molecular-dynamics and annealing simulations of BPDT self-assembled monolayers (SAMs) with up to 100 molecules on a Au(111) substrate, we identify an energetically favorable herringbone-type SAM packing configuration and a less-stable parallel packing configuration. Both SAMs are described by the (2sqrt.3 x sqrt.3)R30 degrees unit cell including two molecules. With subsequent density-functional theory calculations of one unit cell of the (i) herringbone SAM with the molecular tilt angle theta approximately 15 degrees , (ii) herringbone SAM with theta approximately 30 degrees , and (iii) parallel SAM with theta approximately 30 degrees, we confirm that the herringbone packing configuration is more stable than the parallel one but find that the energy variation with respect to the molecule tilting within the herringbone packing is very small. Next, by capping these SAMs with the top Au(111) electrode, we prepare three molecular electronic device models and calculate their coherent charge transport properties within the matrix Green's function approach. Current-voltage (I-V) curves are then obtained via the Landauer-Buttiker formula. We find that at low-bias voltages (|V| < or = 0.2 V) the I-V characteristics of models (ii) and (iii) are similar and the current in model (i) is smaller than that in (ii) and (iii). On the other hand, at higher-bias voltages (|V| > or 0.5 V), the I-V characteristics of the three models show noticeable differences due to different phenyl band structures. We thus conclude that the BPDT SAM I-V characteristics in the low-bias voltage region are mainly determined by the -Au [corrected] interaction within the individual molecule-electrode contact, while both intramolecular conformation and intermolecular interaction can affect the BPDT SAM I-V characteristics in the high-bias voltage region.     

Size-tuneable and micro-patterned iron nanoparticles derived from biomolecules via microcontact printing SAM-modified substrates and controlled-potential electrolyses

Site-selected and size-controlled iron nanoparticles were prepared on coplanar surfaces via microcontact printing of SAM-modified Au/mica electrodes and controlled-potential electrolytic reactions using ferritin biomolecules. Ferritin molecules packed like a full monolayer on 6-amino-1-hexanethiol (AHT)- and 11-amino-1-undecanethiol (AUT)-modified Au/mica surface via electrostatic interactions, which did not depend on the chain length of the amino terminal alkane thiols. After heat-treatment at 400 degrees C for 60 min, iron oxide nanoparticles (ca. 5 nm in diameter) derived from ferritin cores were observed at the Au/mica surface by atomic force microscopy (AFM). On the study on the electrochemistry of ferritin immobilized onto AHT- and AUT-modified Au/mica electrodes, the redox response of the ferritin immobilized AHT-modified electrode was clearly observed. On the other hand, no redox peak for ferritin was obtained at the AUT-modified electrode. The electron transfer between ferritin and the electrode through the AUT membrane could not take place. The difference in the electrochemical response of ferritin immobilized onto AHT- and AUT-modified Au/mica was caused by the chain length of the amino terminal alkane thiols. Uniform patterns of AHT and AUT on the Au/mica electrode surface were performed by use of a poly(dimethylsiloxane) (PDMS) stamp. After the immobilization of ferritin onto both AHT- and AUT-modified electrode surfaces, the modified electrode was applied to a -0.5 V potential for 30 min in a phosphate buffer solution. After this procedure, the PDMS stamp patterning image appeared by scanning electron microscopy (SEM) image. The SEM results induced by the size change of the ferritin core consisting of iron(III) by electrolysis.     

Characterization of Au Nanoparticle Film Electrodes Prepared on Polystyrene

Au nanoparticle films prepared on a polystyrene substrate were studied as a new electrode material. The films were formed from Au particles with different sizes (2–50 nm) and binder molecules (methanethiol, butanethiol, pentanethiol, hexanethiol and heptanethiol) on the substrate with a straightforward procedure. The electrode allows one to monitor reactions occurring only on the nanoparticles, and the catalytic currents resulting from small molecules such as hydrogen peroxide and organic amines were successfully detected in such a manner.