Crystallization kinetics of biaxially stretched natural rubber

The isothermal crystallization of natural rubber was investigated under biaxial stretching. A marked planar orientation of crystals occurs in such a way that the (010) plane orients parallel to the film plane. The rate of crystallization increases with the biaxial stretching ratio, and the Avrami exponent n decreases. At the highest extension, n becomes less than unity. The equilibrium degree of crystallinity decreases with the stretching ratio. The crystallinity was less than 10% for the highest extension. The melting behavior is similar to that in uniaxial stretching.     

Variation of xyloglucan substitution pattern affects the sorption on celluloses with different degrees of crystallinity

The sorption of xyloglucan (XG) on cellulose is a basic feature of the supramolecular assembly of plant cell walls. The binding to cellulose of xyloglucan fractions from Rubus fruticosus suspension-cultured cells with different substitution patterns was assayed on celluloses having various degrees of crystallinity between 20 and 95%. The primary structure of XGs differing in their Xyl/Glc ratio affected their binding to cellulose. The less substituted XGs gave the highest binding yields. Selective removal of the terminal fucosyl residues of XGs differentially affected the binding depending on the crystallinity of cellulose. The results showed large variations on the way cellulose crystallinity affects the binding interaction of XGs. Interestingly, one of the highest binding capacities was exhibited by the primary cell wall cellulose isolated from the actual R. fruticosus cells which also had the lowest crystallinity. Differences in binding to primary wall cellulose appeared to be inversely related to the global substitution of the glucan main chain of XGs.     

Blends of poly(butylene terephthalate) and a polyarylate before and after transesterification

Blends of poly(butylene terephthalate) (PBT) and a copolyester of bisphenol-A with 50% terephthalate-50% isophthalate (PAr), before and after transesterification, have been studied by thermal and dynamic mechanical tests to determine crystallinity and phase behavior. Blends without transesterification, as prepared by solution precipitation, show a single T_g, indicating amorphous miscibility of PBT and PAr. A melting-point depression for PBT crystals is not observed; this means that PBT crystallizes excluding PAr and the entropy of melting is small. The highest fractional crystallinity for PBT is obtained at 20-35% of PAr. Transesterified blends were obtained by holding the physical blends at 250°C for up to 16 h. The transesterified systems show higher T_g's than the corresponding physical blends and also show a marked melting-point depression and lesser PBT crystallinity at the corresponding increased PAr content.     

Determination of crystalline content gradients in cold-drawn poly-L-lactic acid films by DSC

Poly-L-lactic acid (PLLA) is a semi-crystalline, optically active, biodegradable, and biocompatible polymer that has been utilized extensively in biomedical applications as an implantable artificial cell scaffold material. In its crystalline form, PLLA is piezoelectric and it has been implicated in the enhancement of electromechanically induced osteogenesis in vivo. In its amorphous state, however, PLLA does not exhibit piezoelectricity. By uniaxially cold-drawing the polymer, PLLA can be endowed with varying degrees of piezoelectricity. It is important to understand the crystalline architecture of drawn PLLA so that the osteogenic potential imparted by piezoelectricity, if any, can be differentiated from the effects of sample crystallinity. In our work we investigate the induced crystallinity for samples of drawn PLLA at draw ratios between 1.0 and 5.5 by differential scanning calorimetry (DSC). As long-range molecular ordering occurs along the draw axis, we observe an increase in the average percent crystallinity up to a draw ratio of 5.0 and a slight decrease at a draw ratio of 5.5. More importantly, we observe significant heterogeneity in the crystalline content along the draw axis of standard dumbbells cut from PLLA and cold-drawn to representative draw ratios of 2.5 and 4.0. On average, the highest percent crystallinity occurs nearest the dumbbell center, but the maximum crystallinity is independent of draw ratio. Therefore, the draw ratio should not be considered a semi-quantitative estimate of localized PLLA crystallinity and point-to-point analysis of crystallinity in PLLA samples is required for constructing scaffolds with enhanced cell growth properties. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis of zinc glutarates with various morphologies using an amphiphilic template and their catalytic activities in the copolymerization of carbon dioxide and propylene oxide

Various heterogeneous zinc glutarate (ZnGA) catalysts were synthesized in solvent systems of various polarities from zinc acetate dihydrate and glutaric acid with and without the aid of an amphiphilic block copolymer, poly(ethylene glycol‐b‐propylene glycol‐b‐ethylene glycol) (PE6400), as a template. The presence of the PE6400 template and the polarity of the solvent significantly affected the morphology, particle size, surface area, and crystallinity of the resulting catalyst. However, all the catalysts had the same crystal lattice unit cell structure and similar surface compositions. The surface compositions of the catalysts were quite different from those of conventionally prepared ZnGA catalysts, that is, those prepared from zinc oxide and glutaric acid in toluene. All these characteristics of the catalysts influenced the ZnGA‐catalyzed copolymerization of carbon dioxide and propylene oxide. The catalytic activities of the catalysts in this copolymerization depended primarily on their surface area and secondarily on their crystallinity; a larger surface area and a higher crystallinity resulted in higher catalytic activity. Of the catalysts that we prepared, the ZnGA catalyst that was prepared in ethanol containing 5.5 wt % water with the PE6400 template, ZnGA‐PE3, exhibited the highest catalytic activity in the copolymerization. The catalytic activity of ZnGA‐PE3 was attributed to its wrinkled petal bundle morphology, which provided a large surface area and high crystallinity. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4079–4088, 2005     

Calcined Ni—Al layered double hydroxide as a catalyst for total oxidation of volatile organic compounds: Effect of precursor crystallinity

The effect of hydrothermal treatment on properties (crystallinity, porous structure, reducibility, acidity, basicity, and catalytic activity and selectivity in toluene and ethanol total oxidation) of Ni—Al layered double hydroxide precursors and related mixed oxides was examined. The hydrothermal treatment increased considerably both the content of crystalline phase and LDH crystallite size. On the other hand, only a slight effect of the precursor hydrothermal treatment on crystallinity of the related Ni—Al mixed oxides obtained by calcination at 450°C was observed. The reducibility of NiO particles appeared to be hindered considerably compared to the reducibility of pure NiO. Catalytic activity of the Ni—Al mixed oxides prepared from the precursors hydrothermally treated for a short time (4 h) was the highest. The highest amount of acetaldehyde formed during the total oxidation of ethanol, i.e. the worst selectivity was found for the calcined Ni—Al LDH without hydrothermal treatment. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

An Unusual Crystallization Behavior in Polyamide 6/Montmorillonite Nanocomposites

The crystallization behavior and structure of polyamide 6 (PA6) nanocomposites containing 3 wt.‐% montmorillonite (MMT) were investigated for different cooling conditions using differential scanning calorimetry and X‐ray diffraction. In sharp contrast to PA6 and other semicrystalline polymers, increased cooling rates resulted in higher crystallinity of PA6/MMT. The highest crystallinity (60.8%) occurred in the liquid nitrogen‐quenched PA6/MMT film. The results show that the γ‐crystalline form is dominant in the rapidly cooled PA6/MMT.     

Effect of microstructure on hydrolytic degradation studies of poly (l-lactic acid) by FTIR spectroscopy and differential scanning calorimetry

Structural changes during thermally induced crystallization and alkaline hydrolysis of Poly(l-lactic acid) (PLLA) films were investigated using differential scanning calorimetry (DSC), FTIR spectroscopy, weight loss, HPLC and optical microscopy. It was shown that crystallinity (χ_c), glass transition temperature (T_g) and melting temperature (T_m) were found to be strongly annealing temperature (T_a) dependent. The FTIR study of PLLA films suggested that the bands at 921 and 956 cm⁻¹ could be used to monitor the structural changes of PLLA. An independent infrared spectroscopic method was developed for the first time to determine crystallinity of PLLA before degradation and it showed good qualitative correlation with DSC crystallinity. The higher crystallinity values determined by FTIR were attributed to the intermediate phase included in the IR crystallinity. Both the weight loss data and the percentage of lactic acid obtained by HPLC showed that the alkaline hydrolysis of PLLA films increased with increasing crystallinity. The DSC observation showed an increase in T_g and no significant change in T_m and heat of fusion, while IR showed an increase in IR crystallinity with increasing hydrolysis time. The increase in IR crystallinity and T_g with hydrolysis time suggested that degradation progressed from the edges of the crystalline lamellas without decreasing lamellar thickness, but increased the intermediate phase and the short-range order.     

Gas barrier properties of poly(ε‐caprolactone)/clay nanocomposites: Influence of the morphology and polymer/clay interactions

Poly(ε‐caprolactone)/montmorillonite nanocomposites were prepared maintaining a constant inorganic content with three means: melt blending of poly(ε‐caprolactone) with natural or organomodified clays, in situ polymerization of ε‐caprolactone in the presence of organomodified clays, and initiation of ε‐caprolactone polymerization from the silicate layer with appropriate organomodified montmorillonites and activator. In this last case, the polymer chains were grafted to the silicate layers and it was possible to tune up the grafting density. The presence of clays did not modify the polymer crystallinity. It was shown that the in situ polymerization process from the clay surface improved the clay dispersion. The gas barrier properties of the different composite systems were discussed both as a function of the clay dispersion and of the matrix/clay interactions. The highest barrier properties were obtained for an exfoliated morphology and the highest grafting density. Similar evolution of the permeability and the diffusion coefficients was observed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 205–214, 2005     

形貌可控ZnO微纳米结构的水热合成及光催化性能

以乙醇胺为辅助溶剂,采用水热合成法,制备了花状、梭状和剑状的ZnO微纳米结构。采用扫描电镜(SEM)、X射线衍射(XRD)、光致发光光谱(PL)和拉曼光谱等测试手段对样品的形貌、结构、晶相等进行了表征。结果表明所有样品均为六方纤锌矿结构ZnO;其形貌和结晶度可通过改变物质的量的配比nZn2+/nOH-来调控。探讨了反应物配比对产物形貌结构的影响,乙醇胺对不同形貌ZnO的制备起到至关重要作用。以亚甲基蓝为目标降解物,采用紫外-可见吸收光谱(UV-Vis)并结合低温氮吸附-脱附比表面测试(BET),研究了花状、梭状和剑状ZnO的光催化活性。结果表明,与商用ZnO相比,制备的ZnO具有更好的光催化活性;样品催化活性与其比表面积不成正比,具有最小比表面积的花状ZnO拥有最好的光催化活性,这可能是由于其低的结晶度和特殊的花状形貌所致。     

形貌可控ZnO微纳米结构的水热合成及光催化性能

以乙醇胺为辅助溶剂,采用水热合成法,制备了花状、梭状和剑状的ZnO微纳米结构。采用扫描电镜（SEM）、Ｘ射线衍射（XRD）、光致发光光谱（PL）和拉曼光谱等测试手段对样品的形貌、结构、晶相等进行了表征。结果表明所有样品均为六方纤锌矿结构ZnO;其形貌和结晶度可通过改变物质的量的配比n_Zn²⁺/n_OH^-来调控。探讨了反应物配比对产物形貌结构的影响,乙醇胺对不同形貌ZnO的制备起到至关重要作用。以亚甲基蓝为目标降解物,采用紫外-可见吸收光谱（UV-Vis）并结合低温氮吸附-脱附比表面测试（BET）,研究了花状、梭状和剑状ZnO的光催化活性。结果表明,与商用ZnO相比,制备的ZnO具有更好的光催化活性;样品催化活性与其比表面积不成正比,具有最小比表面积的花状ZnO拥有最好的光催化活性,这可能是由于其低的结晶度和特殊的花状形貌所致。     

Some electrical properties of wood pulp treated with sodium hydroxide

The effect of the degree of crystallinity and degree of polymerization on the electrical properties of soda-treated wood pulp has been investigated. The dielectric constant (E′) and the dielectric loss (E″) were measured for the treated samples over a frequency band 0.2–10 MHz at 20°C. Also, the electrical conductivity (σ) was calculated from the measured data of the dielectric constant. From the results obtained we found that the degree of crystallinity and the degree of polymerization decrease with time of oxidation while the number of carboxylic groups increased. E″,E′, and σ were found to increase with the decrease in the degree of crystallinity.     

Drawing of ultrahigh-molecular-weight polyethylene single-crystal mats: The crystallinity

Single-crystal mats of ultrahigh-molecular-weight polyethylene can be drawn uniformly to high draw ratios, more than 20χ at the highest, after the necking process is completed. The dynamic mechanical modulus of the drawn mats increases markedly during the uniform drawing stage. The structural changes induced by the uniform drawing at 100°C have been followed by wide-angle and small-angle x-ray scattering, infrared absorption, differential scanning calorimetry, and birefringence. The crystallinity is estimated from the x-ray amorphous scattering intensity, the IR absorbance of gauche bands, the heat of fusion from DSC, and the density. The estimated crystallinities of the drawn mats are all very high and increase slightly and monotonically with increased drawing after necking, though the values of the crystallinity depend on the method of estimation. IR gauche bands and the SAXS peak due to the long period disappear at a draw ratio of about 80χ. All the results suggest that the uniform drawing after necking destroys the two-phase structure made up of alternately stacked crystalline and amorphous regions and then reorganizes it into a single-phase crystalline structure.     

Crystallinity of fully aromatic thermotropic polyesters of 3,3'-bis(phenyl)-4,4'-biphenol and 1,1'-binaphthyl-4,4'-diol

The degree of crystallinity of as-made fully aromatic, thermotropic polyesters was determined for two different series of polymers, each of which contained a symmetric monomer having either pendant phenyl groups or fused aromatic rings by the WAXD technique. All of the homopolymers had a high degree of crystallinity in spite of bulky substituents attached to the mesogenic moiety. Surprisingly, the homopolymer of 2,6-naphthalenedicarboxylic acid with each of the monomers had a higher degree of crystallinity and T_m than those of the homopolymer of terephthalic acid with each of the respective monomers. As expected, on copolymerization with 30 mol % of either 4-hydroxybenzoic acid or 6-hydroxy-2-naphthoic acid, all of the resulting copolymers had a much lower degree of crystallinity and T_m/T_f values compared to those of the respective homopolymers in each series. © 1994 John Wiley & Sons, Inc.     

Synthesis of novel dithienothiophene‐ and 2,7‐carbazole‐based conjugated polymers and H‐bonded effects on electrochromic and photovoltaic properties

Three kinds of dithienothiophene/carbazole‐based conjugated polymers ( P1–P3 ), which bear acid‐protected and benzoic acid pendants in P2 and P3 , respectively, were synthesized via Suzuki coupling reaction. Interestingly, P1 – P3 exhibited reversible electrochromism during the oxidation processes of cyclic voltammogram studies, and P3 (with H‐bonds) revealed the best electrochromic property with the most noticeable color change. According to powder X‐ray diffraction (XRD) analysis, these polymers exhibited obvious diffraction features indicating bilayered packings between polymer backbones and π‐π stacking between layers in the solid state. Compared with the XRD data of P2 (without H‐bands), H‐bonds of P3 induced a higher crystallinity in the small‐angle region (corresponding to a higher ordered bilayered packings between polymer backbones), but with a similar crystallinity in the wide angle region indicating a comparable π‐π stacking distance between layers. Moreover, based on the preliminary photovoltaic properties of PSC devices ( P1 – P3 blended individually with PCBM acceptor in the weight ratio of 1:1), P3 (with H‐bonds) possessed the highest power conversion efficiency of 0.61% (with J_sc = 2.26 mA/cm², FF = 29.8%, and V_oc = 0.9 V). In contrast to P2 (without H‐bands), the thermal stability, crystallinity, and electrochromic along with photovoltaic properties of P3 were generally enhanced due to its H‐bonded effects. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Effect of crystallization on oxygen‐barrier properties of copolyesters based on ethylene terephthalate

The effect of crystallization from the glassy state (cold crystallization) on the oxygen‐barrier properties of copolyesters based on ethylene terephthalate with up to 10 mol % isophthalate, phthalate, or naphthalate was examined. Generally, crystallization affected diffusivity D more than solubility S; thus, the reduction in permeability P reflected primarily a reduction in D. Systematic changes in crystallinity made it possible to test free‐volume concepts in which permeation of a small gas molecule through a semicrystalline polymer is viewed as proceeding through the amorphous regions with an increased pathway (tortuosity) imposed by plateletlike crystallites. Of the copolymers studied, those with the highest isophthalate or phthalate content (10 mol %) conformed to the simple two‐phase model with constant densities of an impermeable crystalline phase and a permeable amorphous phase. Within the two‐phase model, solubility S correlated linearly with the volume fraction of the amorphous phase, and diffusivity D depended on crystallinity in accordance with the Nielsen model for randomly dispersed platelets with an aspect ratio of 4. The reduction in permeability of the other examined copolyesters could not be described only by the filler effect of crystallites. Data on solubility demonstrated a decrease in amorphous‐phase density upon cold crystallization (de‐densification) like that previously reported for polyethylene terephthalate. Increasing the isophthalate or phthalate content reduced the de‐densification effect, and 10 mol % of these comonomers was sufficient to eliminate the effect altogether. In contrast, 10 mol % naphthalate did not prevent de‐densification. This was attributed to different effects of kinked and linear comonomers on chain packing in the amorphous phase. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1911–1919, 2001     

Effect of Crosslinking Agent on Neem (Azadirachta Indica A. Juss.) Seed Oil (NSO) Encapsulated Microcapsules of κ -Carrageenan and Chitosan Polyelectrolyte Complex

Microencapsulation of neem (Azadirachta Indica A. Juss.) seed oil (NSO) was carried out by polyelectrolyte complexation of κ -carrageenan and chitosan. The microcapsules were crosslinked by using three different crosslinking agents - glutaraldehyde, genipin and tannic acid. The lowest and highest water uptake capacities were exhibited by glutaraldehyde and tannic acid crosslinked matrices, respectively. The release behavior of NSO from encapsulated crosslinked microcapsules followed the order: tannic acid > genipin > glutaraldehyde. Polyelectrolyte complex formation and its interaction with crosslinker was studied. Crosslinking improved thermal stability without affecting crystallinity. Roughness appeared on microcapsule's surface indicated interaction between microcapsules and crosslinker.     

Thermal stability and nonisothermal crystallization of short fiber-reinforced poly(ether ether ketone) composites

The thermal stability of a short carbon-fiber-reinforced PEEK composite was assessed by thermogravimetry and by a Rheometrics dynamic analyzer. The results indicated that holding for 10 min at 380°C was a suitable melting condition to avoid the thermooxidative degradation under air. After proving that the heating rate of 50°C/min can be used to evaluate the crystallinity, a heating stage was used to prepare nonisothermally crystallized specimens using cooling rates from 1 to 100°C/min after melting at 400°C for 3 or 15 min. The degree of crystallinity and the melting behavior of these specimens were investigated by DSC at a heating rate of 50°C/min. The presence of three or four regions indicated that the upper melting temperature, T_m, changed with the crystallization temperature. The first region with the highest T_m, which corresponded to the cooling rate of 1°C/min, can be associated with the crystallization in regime II. There was a second region where T_m decreased as the amount of crystals formed in regime II decreased with increasing cooling rate from 5 to 20°C/min. The third region, a plateau region, corresponded to regime III condition in which the crystals were imperfect. In the fourth region, the cooling was so fast that crystallization was incomplete during the cooling for the melting condition of 400°C for 15 min. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2225–2235, 1998     

Preparation and photocatalytic activity of multi-modally macro/mesoporous titania

Hierarchically disorder sponge-like macro/mesoporous titania was prepared by adding distilled water dropwise to a coating of tetrabutyl titanate. The results reveal that the un-calcined samples show obvious photocatalytic activity and multi-modal pore-size distribution. With increasing calcination temperatures, the photocatalytic activity and crystallinity increase. At 400°C, the calcined sample shows the highest photocatalytic activity. Further increasing the calcination temperatures results in the decrease of photocatalytic activity due to the drastic decrease of specific surface areas. However, the 600°C-calcined sample exhibits the highest specific photocatalytic activity due to high anatase crystallinity.     

Comparison of low crystallinity TiO2 film with nanocrystalline anatase film for dye-sensitized solar cells

Dye adsorption and microstructure of TiO₂ film are important properties when it is used as photoelectrode of dye-sensitized solar cells (DSCs). This study investigated the application of a low crystallinity TiO₂ film in DSCs. The low crystallinity TiO₂ film is composed of interconnected spherical particles with an average size of 20 nm and has homogeneous mesoporous inner structure. A DSC based on the anatase nanocrystalline mesoporous film prepared by P25 was used for comparison purpose. It is shown that although loaded with much less dye, the DSC based on the low crystallinity TiO₂ film generated I_sc (short circuit photocurrent) as much as the one based on the conventional anatase nanocrystalline film does and obtained higher V_oc (open circuit photovoltage) as well as ff (fill factor). The overall light-to-electricity efficiency (η) of the DSC based on the low crystallinity TiO₂ film reached 5.37%, while the η of the DSC based on anatase nanocrystalline film was 4.69% in this work condition. It is suggested that a low crystallinity TiO₂ mesoporous film with a proper microstructure is as efficient as the anatase nanocrystalline mesoporous film when used in DSCs.