Experimental investigation of the impact on nearby solid boundary during laser-generated bubble collapse

Cavitation damage has been considered as being responsible for many effects in hydraulic machinery and biological medicine. In order to better understand the cavity interaction with nearby solid surfaces, the impact loading induced by the high-speed liquid-jet and subsequent jet flow during the final stage of the bubble collapse in a static fluid is investigated by focusing a Q-switched pulsed laser into water. By means of a new method based on a fibre-coupling optical beam deflection technique, a detailed experimental study has been made to clarify the relationship of the impact pressure against a solid boundary as a function of the dimensionless γ that is generally used to describe the bubble dynamics with its definition γ= s/R_{max}(R_{max} being the maximum bubble radius and s denoting the distance of the cavity inception from the boundary). The experimental results are shown that for γ in the range of about 0.67 to 0.95 with a pulsed laser energy 230mJ, the transient pressure applied on the solid surface is maximum; while for γ>1 or γ<0.67, it is gradually decreased. By combination of our experimental results with the other work that detected the acoustic emission during the bubble collapse at different γ, it is concluded that in this range of 0.67－0.95, the destructive effect due to a liquid-jet and the following jet flow impact actually outweighs the well-known effect of shock wave emission and plays a vital role during the cavitation bubble collapse.     

圆锥边界附近激光空泡溃灭行为的研究

为了研究刚性圆锥边界锥角对激光空泡溃灭行为的影响,文章建立了虚拟平面边界模型, 同时采用阴影摄影术、光偏转法以及数值计算的手段对边界附近空泡溃灭过程进行了研究. 结果表明边界的锥角对空泡的形状、溃灭时间以及液体射流形成均有明显影响. 空泡形状偏离球形的程度和溃灭时间均随锥角的增大而增大,且增大锥角度可以促使射流的形成. 空泡溃灭时间的实验值同理论值具有较高的一致性,验证了虚拟平面边界假设及无量纲距离修正的有效性.     

Experimental investigation of the collapse of laser-generated cavitation bubbles near a solid boundary

The oscillation of a laser-generated single cavitation bubble near a solid boundary is investigated by a fiber-optic diagnostic technique based on optical beam deflection (OBD). The maximum bubble radii and collapse time for each oscillation cycle are determined from a sequence of bubble oscillations. Furthermore, by combining the revised Rayleigh theory, the prolongation factor κ at different dimensionless parameter γ (γ=L/R_max, where R_max is the maximum bubble radius and L is the distance of a cavity inception point from a boundary) is obtained. In addition, the prolongation factor of the collapse time versus laser energy is also derived, which are valuable in the fields of hydraulic cavitation, laser lithotripsy and laser ophthalmology.     

表面张力对固壁旁空泡运动特性影响的理论和实验研究

表面张力是影响空泡脉动及空蚀的一个重要因素.对五种不同表面张力液体中空泡脉动（膨胀和收缩）过程进行了研究,并将实验结果与基于空泡生长和溃灭理论的计算结果进行了对比.实验中,用激光作为测试光源,采用光偏转测试系统研究了不同表面张力液体中空泡泡壁运动规律及泡壁速度的变化.结果表明：表面张力对空泡膨胀过程起抑制作用,故液体表面张力愈大,空泡能达到的最大直径越小;表面张力对空泡的收缩过程则起加速作用,液体表面张力愈大,收缩越迅速,空泡泡壁运动速度越大,其所产生的瞬时溃灭压强越大,空化效果越好. 关键词： 表面张力 空泡 光偏转     

Optical investigation of cavitation erosion by laser-induced bubble collapse

By means of a new force sensor based on optical beam deflection (OBD), the mechanical effects of laser-matter interaction underwater at different incident laser energy are investigated in detail. The experimental results show that a target underwater is impacted in turn by laser-plasma ablation force and high-speed liquid-jet impulse induced by bubbles collapse in the vicinity of a solid boundary. Furthermore, the amplitudes of the two forces increase monotonously with laser energy. According to the ablation force detected by the experiment and the theoretical relationship between laser intensity and ablation pressure, the value of liquid-jet impact against a solid boundary can be easily obtained. In addition, based on the model of a collapsing bubble, some characteristic parameters, such as the liquid-jet impact velocity, the maximum bubble radius, the bubble energy can also be obtained at different laser energy, which are valuable in the corresponding research fields.     

激光烧蚀水下金属产生冲击波和空泡效应的研究

采用自行研制的高灵敏度光束偏转测试系统,对脉冲激光烧蚀水下金属产生的等离子体冲击波和空泡效应进行了实验研究。实验得到了激光等离子体冲击波的传播规律、冲击波与激光空泡的分离过程、空泡的脉动特性以及空泡溃灭冲击波的形成机制。结果表明,空泡最大和最小泡径、振荡周期均随着脉动次数的增加呈减小趋势,且减小幅度较大。最小收缩泡径由泡能和腔内含气量共同决定。在同一次脉动过程中,空泡膨胀所需的时间明显大于收缩所需的时间。     

含气量对液体中空泡声波频谱特性的影响

通过压电陶瓷（PZT）水听器获取了液体中激光空泡脉动辐射的声波,并计算了激光空泡在第1次脉动过程中泡内的含气量,结合空泡含气量对空泡最大半径及脉动周期影响的分析,进而分析了含气量对空泡声波频谱特性的影响。分析结果表明:激光空泡第1次脉动过程中泡内的含气量随着作用激光能量的增加而增加,含气量的多少将直接影响空泡运动的剧烈程度;含气量越多,空泡脉动越缓慢,脉动周期越长,空泡脉动辐射声波的峰值频率有向低频移动的趋势。     

含气量对液体中空泡声波频谱特性的影响

通过压电陶瓷（PZT）水听器获取了液体中激光空泡脉动辐射的声波,并计算了激光空泡在第1次脉动过程中泡内的含气量,结合空泡含气量对空泡最大半径及脉动周期影响的分析,进而分析了含气量对空泡声波频谱特性的影响。分析结果表明：激光空泡第1次脉动过程中泡内的含气量随着作用激光能量的增加而增加,含气量的多少将直接影响空泡运动的剧烈程度;含气量越多,空泡脉动越缓慢,脉动周期越长,空泡脉动辐射声波的峰值频率有向低频移动的趋势。     

黏性液体中激光空泡脉动特性的理论和实验研究

通过自行研制的光偏转测试系统对黏性液体中激光空泡脉动特性进行了实验，获得了激光等离子体空泡前两次脉动全过程，从而判定了空泡在脉动过程中对应的最大和最小泡半径；并将不同黏性系数下空泡脉动结果与基于空泡溃灭理论的计算结果进行了对比.结果表明：液体黏性对空泡生存周期、空泡半径，以及泡壁的运动速度等均有影响.受液体黏性影响，空泡膨胀或收缩过程明显变缓，其相应的生存周期也越长.这一研究结果不仅可促进空化研究的深入，也可为合理利用空化现象提供参考. 关键词： 激光泡 脉动特性 黏性 光纤传感器     

Mechanism of laser-induced plasma shock wave evolution in air

A theoretical model is proposed to describe the mechanism of laser-induced plasma shock wave evolution in air. To verify the validity of the theoretical model, an optical beam deflection technique is employed to track the plasma shock wave evolution process. The theoretical model and the experimental signals are found to be in good agreement with each other. It is shown that the laser-induced plasma shock wave undergoes formation, increase and decay processes; the increase and the decay processes of the laser-induced plasma shock wave result from the overlapping of the compression wave and the rarefaction wave, respectively. In addition, the laser-induced plasma shock wave speed and pressure distributions, both a function of distance, are presented.     

Experimental investigation of the effect of ambient pressure on laser-induced bubble dynamics

The effect of ambient pressure on the dynamics of laser-induced bubbles was investigated by a fiber-optic diagnostic technique based on probe beam deflection (PBD). The experimental criterion for judging the maximum bubble radius is modified to the average value of the detecting distances at which the characteristic waveform signals appear. The ambient pressure affects the maximum radius and collapse of bubble strongly. The experimental results indicate that the maximum bubble radius and the collapse time both decrease nonlinearly while the ambient pressure increases linearly, and the decreasing velocities of them are smaller at a larger ambient pressure. The predicted value of collapse time has a good agreement with experiment at larger ambient pressure.     

固壁面附近激光产生空泡脉动过程的实验研究

采用自行研制的光纤传感器研究了激光等离子体空泡在固壁面附近的脉动特性。实验获得了激光空泡三次膨胀到最大位置对应的波形图;并据此判定了激光空泡在脉动过程中对应的最大泡半径和溃灭周期;在此基础上结合空泡溃灭理论,计算了激光泡溃灭周期的延长因子κ。结果表明:随着脉动次数的增加,最大泡半径依次减小;随着作用激光能量的增大,最大泡半径,空泡溃灭周期的延长因子κ均增大;而无量纲参量的增大将导致延长因子的减小。所得到的延长因子同样可用于无限域流场。     

Non-linear behaviour and stability of trapped micron-sized cylindrical gas bubbles in an ultrasonic field

Stable arrays of cylindrical bubbles with diameters 3 and 4 μm were produced by trapping air in the pores of hydrophobic Nuclepore filters. These bubble arrays were irradiated by beams of cw and pulsed ultrasound at carrier frequencies near the resonance frequencies of the trapped bubbles. By examining the frequency spectrum of the field scattered by the arrays it was found that the bubbles may oscillate as non-linear stable cavities of long duration. Using short pulses, the bubbles remain stable up to excitation pressure amplitudes of several bars. Mechanisms for the eventual growth and decay of the bubbles are discussed in light of the observations.     

固体壁面附近激光空泡的动力学特性研究

关键词：     

Production of large size single transient cavitation bubbles with tube arrest method

Large size single transient cavitation bubbles of maximum diameter up to 3 cm with sonoluminescence have been generated in water by the ‘tube arrest' method. A simplified one-dimensional model of bubble growing and water column motion is proposed. The results of numerical simulation are compared with the experimental data of the bubble size and oscillation period as the key parameters.     

Experimental investigations of three laser-induced synchronized bubbles

Herein, we investigated experimentally the dynamics of three laser-induced, same-sized, symmetrically aligned, and synchronized bubbles. Three synchronized laser beams split from the same beam using a Diffractive Optical Element splitter were focused on water, and then we obtained three bubbles. Another nanosecond laser pulse was used to probe the bubbles to obtain shadowgraphs. The exact delay of the excited and detected light was controlled using a delay generator. The results revealed that the maximum volumes of bubbles in arrays decrease as the normalized distance falls, while the lifetimes and translation increase. It was explained by the interaction between the acoustic radiation of bubbles and the surrounding bubbles. The shrinkage of linear bubble arrays exists an anomaly. The center bubbles were stretched, to ellipsoid, stick, even fractured, by the peripheral bubbles. The closer they are, the more distinct is the above phenomenon. However, when the normalized distance was sufficiently small, instead of being stretched, the center bubbles were compressed to disk shape and thus shrank with the whole array. Finally, the dependence of the distance on the energy transfer of the bubble system is also discussed.     

含气量对黏性液体中空泡脉动特性的影响

采用自行研制的高灵敏度光偏转测试系统,研究黏性液体中激光空泡脉动特性.判定了空泡两次脉动对应的最大和最小泡半径,进而计算了激光空泡在前两次脉动过程中泡内的含气量.研究表明：泡内含气量对泡脉动特性有较大影响.随着脉动次数的增加,空泡泡内含气量增大.空泡最大泡半径随含气量的增加而增大.此外,受液体黏性影响,空泡膨胀和收缩过程明显变缓. 关键词： 含气量 黏性 激光空泡 脉动特性     

Study on shock wave-induced cavitation bubbles dissolution process

This study investigated dissolution processes of cavitation bubbles generated during in vivo shock wave(SW)-induced treatments. Both active cavitation detection(ACD) and the B-mode imaging technique were applied to measure the dissolution procedure of bi Spheres contrast agent bubbles by in vitro experiments. Besides, the simulation of SW-induced cavitation bubbles dissolution behaviors detected by the B-mode imaging system during in vivo SW treatments, including extracorporeal shock wave lithotripsy(ESWL) and extracorporeal shock wave therapy(ESWT), were carried out based on calculating the integrated scattering cross-section of dissolving gas bubbles with employing gas bubble dissolution equations and Gaussian bubble size distribution. The results showed that(i) B-mode imaging technology is an effective tool to monitor the temporal evolution of cavitation bubbles dissolution procedures after the SW pulses ceased, which is important for evaluation and controlling the cavitation activity generated during subsequent SW treatments within a treatment period;(ii) the characteristics of the bubbles, such as the bubble size distribution and gas diffusion, can be estimated by simulating the experimental data properly.     

球状泡群内气泡的耦合振动

振动气泡形成辐射场影响其他气泡的运动, 故多气泡体系中气泡处于耦合振动状态. 本文在气泡群振动模型的基础上, 考虑气泡间耦合振动的影响, 得到了均匀球状泡群内振动气泡的动力学方程, 以此为基础分析了气泡的非线性声响应特征. 气泡间的耦合振动增加了系统对每个气泡的约束, 降低了气泡的自然共振频率, 增强了气泡的非线性声响应. 随着气泡数密度的增加, 振动气泡受到的抑制增强; 增加液体静压力同样可抑制泡群内气泡的振动, 且存在静压力敏感区(1–2 atm, 1 atm=1.01325×10⁵ Pa); 驱动声波对气泡振动影响很大, 随着声波频率的增加, 能够形成空化影响的气泡尺度范围变窄. 在同样的声条件、泡群尺寸以及气泡内外环境下, 初始半径小于5 μm 的气泡具有较强的声响应. 气泡耦合振动会削弱单个气泡的空化影响, 但可延长多气泡系统空化泡崩溃发生的时间间隔和增大作用范围, 整体空化效应增强.     

Experimental investigation on dynamic characteristics and strengthening mechanism of laser-induced cavitation bubbles

The dynamic features of nanosecond laser-induced cavitation bubbles near the light alloy boundary were investigated with the high-speed photography. The shock-waves and the dynamic characteristics of the cavitation bubbles generated by the laser were detected using the hydrophone. The dynamic features and strengthening mechanism of cavitation bubbles were studied. The strengthening mechanisms of cavitation bubble were discussed when the relative distance parameter γ was within the range of 0.5–2.5. It showed that the strengthening mechanisms caused by liquid jet or shock-waves depended on γ much. The research results provided a new strengthening method based on laser-induced cavitation shotless peening (CSP).