Photoinitiated,inverse emulsion polymerization of acrylamide: Some mechanistic and kinetic aspects

The kinetics of photoinitiated, inverse emulsion polymerization of acrylamide with 2,2‐dimethoxy‐2‐phenylacetophenone (DMPA) as a photoinitiator was investigated under three different cases. First, in a quartz reactor transparent to full UV light, the polymerization rate (R_p) increased and then decreased with the change of initiator order from 0.27 to a negative value when the DMPA concentration was increased, and it was particularly unusual that monomer orders at different DMPA concentrations were lower than the first. Second, for polymerization without DMPA in a quartz reactor, the dependence of R_p on monomer concentration was similar to that of R_p on initiator concentration in the aforementioned case. Third, when polymerization was carried out in a Pyrex reactor where the far UV light was filtered, a peak rate was also observed, and initiator orders varied from 0.24 to a negative value; however, under this case monomer orders at different initiator concentrations were greater than the first. These results indicated that the effect of absorbance often observed in bulk or solution photopolymerization also existed in this system, and the self‐initiation of monomer had some influence on polymerization, and the role of primary radical termination could not be neglected, as evidenced by kinetic analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 846–852, 2004     

2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑复合光引发体系的光聚合动力学研究

本文研究了对2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑(BMOIM)复合光引发体系引发聚合动力学过程.采用紫外光谱仪对引发剂、供氢体、增感剂在紫外区的吸收谱图进行了表征.利用实时红外光谱仪对复合光引发体系引发聚合动力学过程进行实时监测,考察了不同光强、引发剂浓度以及不同官能度单体对反应速率及最终双键转化率的影响.结果表明,在引发剂浓度为0.6%(质量分数)时,20s内双键转换率达到96%,随着引发剂浓度的提高,聚合速率增大.聚合速率以及最终双键转化率随着光强增大而增大;双官能团单体的最终双键转化率比三官能团单体的最终双键转化率要高.     

Ring‐opening polymerization of 1,4‐dioxan‐2‐one initiated by lanthanum isopropoxide in bulk

Lanthanum isopropoxide (La(OiPr)₃) has been synthesized and employed for ring‐opening polymerization of 1,4‐dioxan‐2‐one in bulk as a single‐component initiator. The influences of reaction conditions such as initiator concentration, reaction time, and reaction temperature on the polymerization were investigated. The kinetics indicated that the polymerization is first‐order with respect to the monomer concentration. The Mechanistic investigations according to ¹H NMR spectrum analysis demonstrated that the polymerization of PDO proceeded through a coordination‐insertion mechanism with a rupture of the acyl‐oxygen bond of the monomer rather than the alkyl‐oxygen bond cleavage. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5214–5222, 2008     

Photoinitiated cationic polymerization of epoxy alcohol monomers

A series of epoxy alcohols were prepared by simple, straightforward methods. These compounds were very reactive monomers that polymerized rapidly on UV irradiation in the presence of cationic photoinitiators. The kinetics of the cationic photopolymerization of these monomers were studied with diaryliodonium salt photoinitiators and real‐time IR spectroscopy. The rate of epoxide ring‐opening polymerization was enhanced markedly by the presence of the hydroxy group. Using model compounds, the monomers were shown to polymerize via an activated monomer mechanism. Simple epoxy alcohols polymerized to give polymers with a hyperbranched structure. The novel monomers also were observed to accelerate the rate of the photopolymerization of mono‐ and multifunctional epoxides. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 389–401, 2000     

Benzotriazole derivatives as long wavelength photosensitizers for diaryliodonium salt initiators

Two benzotriazole derivative dyes 4,7‐bis(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐5‐yl)‐2‐dodecyl‐2H‐benzo[1,2,3]triazole, and 2‐dodecyl‐4,7‐bis(4‐hexylthiophen‐2‐yl)‐2H‐benzo[d][1,2,3]triazole are shown to work as efficient photosensitizers for a diphenyliodonium salt initiator in cationic photopolymerization of epoxide and vinyl monomers. Substituted thienyl groups are attached to benzotriazole backbone to extend conjugation and enhance electron density of the molecules. Thereby, it was possible to initiate polymerizations at room temperature using long wavelength UV and visible light. The progress of photopolymerizations was monitored using optical pyrometry. The photopolymerization of an epoxide monomer using solar irradiation was also demonstrated. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effect of monomer water solubility on cationic microemulsion polymerization of three components (water,surfactant, and monomer)

Here, we present the oil/water (O/W) microemulsion polymerization in three‐component microemulsions of n‐butyl acrylate, ethyl acrylate, and methyl acrylate, monomers with similar chemical structures but different water solubilities using the cationic surfactant dodecyl trimethyl ammonium bromide. The effects of monomer water solubility, initiator type and initial monomer concentration on the polymerization kinetics were studied. Reaction rates were high with final conversions between 70 and 98% depending on the monomer and reaction conditions. The final latexes were bluish, with a particle size ranging between 20 and 50 nm and polymer with molar masses in the order of 10⁶ g mol^?1. Increasing monomer water solubility resulted in a slower reaction rate, larger particles and a lower number density of particles. A higher reaction rate, larger average particle size and higher particle number density were obtained by increasing the monomer concentration. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Sesamin as a co-initiator for UV photopolymerization

Sesamin, a nature compound from sesame seed, which contains two cyclic acetal structures, was used as a co-initiator for UV polymerization initiator system, and 1,6-Hexanedioldiacrylate was used as the photopolymerization monomer. Photopolymerization kinetics was recorded by real-time infrared spectroscopy. For BP/Sesamin initiator system, the double bond conversion increased with the increase of Sesamin concentration and light intensity. Combination of p-chlorobenzophenone and Sesamin had the highest initiating reactivity. The polymerization rate and final double bond conversion of acrylate monomer were higher than that of methacrylate monomer.     

Living radical polymerization of acrylonitrile catalyzed by copper with a high concentration of radical initiator and its application in removal of Ag(I) after modification

In this study, we reported the synthesis of polyacrylonitrile (PAN) via living radical polymerization in N, N‐dimethylformamide using carbon tetrachloride as initiator, copper(II) chloride (CuCl₂)/hexamethylenetetramine as catalyst system, and 2,2‐azobisisobutyronitrile as a high concentration of thermal radical initiator. The polymerization proceeded in controlled/living manner as indicated by first‐order kinetics of the polymerization with respect to the monomer concentration, linear increase of the molecular weight with monomer conversion and narrow polydispersity. Higher polymerization rate and narrower molecular weight distributions were observed with CuCl₂ less than 50 ppm. The rate of polymerization showed a trend of increase along with temperature. The modified PAN containing amidoxime group was used for extraction of Ag(I) ions from aqueous solutions. The adsorption kinetics data indicated that the adsorption process followed pseudo‐second‐order rate model. The isotherm adsorption process could be described by the Freundlich isotherm model. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Atom transfer radical polymerization of ionic liquid 2‐(1‐butylimidazolium‐3‐yl)ethyl methacrylate tetrafluoroborate

Polymeric forms of ionic liquids may have many potential applications because of their high thermal stability and ionic nature. They are generally synthesized by conventional free‐radical polymerization. Here we report a living/controlled free‐radical polymerization of an ionic liquid monomer, 2‐(1‐butylimidazolium‐3‐yl)ethyl methacrylate tetrafluoroborate (BIMT), via atom transfer radical polymerization. Copper bromide/bromide based initiator systems polymerized BIMT very quickly with little control because of fast activation but slow deactivation. With copper chloride as the catalyst and trichloroacetate, CCl₄, or ethyl α‐chlorophenylacetate as the initiator, BIMT was polymerized at 60 °C in acetonitrile with first‐order kinetics with respect to the monomer concentration. The molecular weight was linearly dependent on the conversion. The monomer concentration strongly affected the polymerization: a low monomer concentration caused the polymerization to be incomplete, probably because of catalyst disproportionation in polar solvents. The addition of a small amount of pyridine suppressed such disproportionation, but a further increase in the amount of pyridine greatly slowed the polymerization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5794–5801, 2004     

Cross‐linking photopolymerization of monoacrylate initiated by benzophenone

The chain‐end structure of the photopolymerized acrylate using benzophenone as an initiator was investigated as well as polymerization behavior. Dodecyl acrylate was used as a monomer in this study. Gelation occurred during ultraviolet (UV) irradiation, whereas a cross‐linker was not employed. Conversion‐time profile below gel point gave a linear first‐order plot suggesting that the steady‐state was held throughout polymerization. Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectra of the resultant polymer indicated that most polymers had an acryloyl group at one of the chain‐ends, while some polymers had an acryloyl group at each chain‐end. The cross‐linking reaction leading to gelation would have been caused by the subsequent copolymerization of the residual monomer with the latter polymer having two acryloyl groups. Dissolved oxygen in the monomer solution influenced the polymer structure giving hydroxyl group at chain‐end. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1545–1553     

电荷转移聚合研究——苯肼及其衍生物引发丙烯腈聚合

研究了苯肼(PHZ)及其衍生物引发丙烯腈(AN)聚合以及苯肼作为电子给体与醌作为电子受体形成的电荷转移复合物(CTC)对丙烯腈的引发聚合作用。测定了光聚合时的引发剂、单体指数和聚合活化能分别为0.66、2.1和33.4千焦耳/摩尔。光聚合机理认为是PHZ与AN在光照下形成激基复合物(exciplex),它分解产生自由基引发单体聚合。而暗聚合的机理认为是PHZ与醌形成CTC,CTC再分解引发单体聚合。exciplex与CTC分别已由荧光光谱和紫外吸收光谱检出。     

Photoinitiated polymerization of acrylate,methacrylate, and vinyl ether end‐functional polyisobutylene macromonomers

Polyisobutylene‐based UV cured networks potentially useful as sealants were synthesized by photopolymerization of well‐defined polyisobutylene methacrylate (PIB‐MA), acrylate (PIB‐A) and vinyl ether (PIB‐VE) di‐ and trifunctional macromonomers. The kinetics of photocrosslinking were measured using an optical pyrometer apparatus and optimized with respect to different experimental parameters. PIB‐MA/A macromonomers displayed enhanced reactivity in radical photopolymerization in the presence of a bis(acylphosphine) oxide photoinitator. PIB‐VE macromonomers exhibited a high rates of photopolymerization with (4‐n‐octyloxyphenyl)phenyliodonium hexafluroantimonate as the photoinitiator. The rates as well as the ultimate monomer conversions were increased by increasing the irradiation light intensity. The inherent induction period associated with oxygen inhibition in the photopolymerization of PIB‐MA was significantly reduced by optimizing the choice of photoinitiator. A detailed investigation of the concentration of MA/A/VE end groups revealed the presence of a prominent saturation effect in the photopolymerization of PIB‐A, which was absent with PIB‐MA and PIB‐VE. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

ATRP of MMA under 60Co γ‐irradiation at room temperature

In this work, atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was successfully carried out at room temperature (25 °C) under ⁶⁰Co γ‐irradiation environment. The polymerization proceeded smoothly with high conversion (>90%) within 7 h. The polymerizations kept the features of controlled radical polymerization: first‐order kinetics, well‐predetermined number‐average molecular weights (M_n,GPC), and narrow molecular weight distributions (M_w/M_n < 1.25). ¹H NMR spectroscope and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry confirmed that poly(methyl methacrylate) (PMMA) chain was end‐capped by the initiator moieties. The Cu(II) concentration could reduce to 20 ppm level while keeping good control over molecular weights. This is the first successful example for the ATRP of MMA under ⁶⁰Co γ‐irradiation at room temperature. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Solid‐state polymerization of 2,3,6,7,10,11‐hexa(methacrylate) triphenylene

A new monomer, 2,3,6,7,10,11‐hexa(methacrylate) triphenylene (HMTP), and its crystals have been successfully synthesized, and the solid‐state polymerization under UV irradiation has been investigated. The photo polymerization of HMTP in solid was confirmed by the reduction of vinyl bonds in the FT‐IR and UV spectra of PHMTP in comparison with the corresponding spectra of its precursor. Thus, IR spectroscope was used to follow the polymerization of HMTP crystals under UV irradiation, and kinetic studies show a first‐order reaction with rate constant of 6.12 × 10^?3 min^?1. This value is slightly larger than that measured by the weight method. The polarizing optical microscope and X‐ray diffraction were used to study the crystal structure difference between the polymers and its monomer. The results show that the polymers' crystals obtained from photo polymerization kept the monomer crystal lattice. Because of strong overlap between the π‐electron of the triphenylene, the monomer and polymer crystals showed different fluorescence properties. All these results proved that the photo polymerization of HMTP crystals is governed by the packing structure of monomer molecules; in other words, this reaction is just lattice controlled polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1526–1534, 2005     

Fast copper catalyzed living radical polymerization of acrylonitrile utilizing a high concentration of radical initiator

This article first reports a fast and controlled living radical polymerization (LRP) of acrylonitrile, evidenced by 81.3% monomer conversion within 40 min and well‐defined the polymers with a narrow polydispersity index (PDI) range of 1.14?1.38. This was achieved by utilizing azobis(isobutyronitrile) as radical initiator with a high concentration up to 190 mM and CuBr₂ as catalyst with a very low concentration down to 50 ppm. The polymerization displayed typical LRP characteristics, including pseudo first‐order kinetics of polymerization, the linear increase of number‐average molecular weights (MWs), low PDI values. The influence of various experimental components, radical initiator concentration, catalyst concentration, and reaction temperature, on the polymerization reaction and MW as well as PDI has been investigated in detail. ¹H NMR and gel permeation chromatography analyses as well as chain extension reaction confirmed the very high chain‐end functionality of the resultant polymer. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

The preparation of amphiphilic core‐shell nanospheres by using water‐soluble macrophotoinitiator

The amphiphilic poly(AM‐co‐SA)‐ITXH macrophotoinitiator was synthesized by precipitation photopolymerization under UV irradiation with isopropylthioxanthone (ITX) as free radical photoinitiator. A novel method has been developed to prepare amphiphilic core‐shell polymer nanospheres via photopolymerization of methyl methacrylate (MMA) in aqueous media, with amphiphilic copolymer macrophotoinitiator poly(AM‐co‐SA)‐ITXH. During polymerization, the amphiphilic macroradicals underwent in situ self‐assembly to form polymeric micelles, which promoted the emulsion polymerization of the monomer. Thus, amphiphilic core‐shell nanospheres ranging from 70 to 140 nm in diameter were produced in the absence of surfactant. The conversion of the monomer, number average molecular weights (M_n), and particle size were found to be highly dependent on the macrophotoinitiator and monomer concentration. The macrophotoinitiator and amphiphilic particles were characterized by FTIR, UV‐vis, ¹H NMR, TEM, DSC, and contact angle measurements. The results showed the particles had well‐defined amphiphilic core‐shell structure. This new method is scientifically and technologically significant because it provides a commercially viable route to a wide variety of novel amphiphilic core‐shell nanospheres. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 936–942, 2010     

Synthesis of crosslinked poly(butyl methacrylate‐co‐pentaerythritol triacrylate) gel by single electron transfer‐living radical polymerization and its oil‐absorbing properties

A novel high oil‐absorbing crosslinked gel was synthesized by copolymerization of butyl methacrylate (BMA) with a small amount of pentaerythritol triacrylate (PETA) crosslinker using single electron transfer‐living radical polymerization (SET–LRP) initiated with carbon tetrachloride (CCl₄) and catalyzed by Cu(0)/hexamethylenetetramine (HMTA) in N, N‐dimethylformamide (DMF). The polymerization followed first‐order kinetics as indicated by linear increase of monomer concentration with reaction time. Effects of reaction temperature, crosslinker, initiator, and catalyst on the oil‐absorbing properties of the crosslinked gel were investigated in detail. The oil absorptions of the crosslinked gel to chloroform, toluene could reach 51.9, 34.5 g/g, respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Acrylate nanolatex via self‐initiated photopolymerization

The use of UV light to initiate emulsion polymerization processes is generally overlooked, whilst extensive literature exists on photocuring of monomer films. In this study, the unique potential of UV light to produce at ambient temperature polyacrylate latexes without initiator was exploited. Although radical initiators are utilized at low concentration, their cost, toxicity, and odor provide incentives for finding alternatives. Starting with concentrated (30 wt %) and low scattering acrylate miniemulsions (droplet diameter <100 nm), it was demonstrated that acrylate self‐initiation can promote an efficient and fast photopolymerization in micrometer‐scale reactor (spectrophotometric cell) and lab‐scale photoreactor. Herein, all kinetic, colloidal, and mechanistic aspects involved in the self‐initiation of acrylate miniemulsion were extensively examined to provide a complete picture. In particular, the effects of droplet size, initiating wavelength, optical path, and irradiance on the course of the polymerization were thoroughly discussed. A diradical self‐initiation pathway is the most likely mechanism. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1843–1853     

Polymerization of cyclopentadiene initiated by methylaluminoxane

The polymerization of cyclopentadiene (CPD) was effectively initiated by methylaluminoxane (MAO) to generate poly(cyclopentadiene) (polyCPD). The effects on the polymerization of some reaction parameters such as the monomer concentration, the initiator concentration, and solvents were investigated. The conversion of CPD was monitored with gas chromatography to investigate the reaction kinetics. The polymerization rate was proportional to the concentrations of MAO in the first order and of the CPD monomer in the second order, and a reasonable cationic polymerization mechanism was suggested on the basis of the kinetic study. PolyCPD obtained at a low temperature could be dissolved in toluene or chloroform, and this indicated lower cross‐coupling during the polymerization reaction. ¹H NMR and IR analysis of the polymer indicated that there were almost equal amounts of 1,2‐enchainment and 1,4‐enchainment in the polymer chain. The measurement of polyCPD showed its unique properties as a potential candidate for stable wrappings or electronic packaging materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 264–272, 2006     

Diselenocarbamates,novel initiators in ATRP of styrene

The atom transfer radical polymerizations (ATRPs) of styrene initiated by diselenocarbamates were carried out for the first time. The polymerization showed first‐order kinetic with respect to the monomer concentration, and the molecular weights of the obtained polymers increased linearly with the monomer conversions with narrow molecular weight distributions (as low as 1.16). The results of chain extension, ¹H NMR, UV–vis, and MALDI‐TOF MS confirmed that the resultant polystyrene possessed some degree of living diselenocarbamates terminal. However, significant amounts of dead polymers (about 53%) were also found. This work offered an alternative type of ATRP initiator, and the seleno‐terminated polymers may be useful in biotechnological and biomedical applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1927–1933