Highly branched and high‐molecular‐weight polyethylenes produced by 1‐[2,6‐bis(bis(4‐fluorophenyl)methyl)‐4‐MeOC6H2N]‐2‐aryliminoacenaphthylnickel(II) halides

A series of unsymmetrical 1‐[2,6‐bis(bis(4‐fluorophenyl)methyl)‐4‐MeOC₆H₂N]‐2‐aryliminoacenaphthene‐nickel(II) halides has been synthesized and fully characterized by Fourier transform infrared spectroscopy, proton nuclear magnetic resonance (¹H NMR), ¹³C NMR, and ¹⁹F NMR spectroscopy as well as elemental analysis. The structures of Ni1 and Ni6 have been confirmed by the single‐crystal X‐ray diffraction. On activation with cocatalysts either ethylaluminum sesquichloride or methylaluminoxane, all the title nickel complexes display high activities toward ethylene polymerization up to 16.14 × 10⁶ g polyethylene (PE) mol^?1(Ni) h^?1 at 30 °C, affording PEs with both high branches (up to 103 branches/1000 carbons) and molecular weight (1.12 × 10⁶ g mol^?1) as well as narrow molecular weight distribution. High branching content of PE can be confirmed by high temperature ¹³C NMR spectroscopy and differential scanning calorimetry. In addition, the PE exhibited remarkable property of thermoplastic elastomers (TPEs) with high tensile strength (σ_b = 21.7 MPa) and elongation at break (ε_b = 937%) as well as elastic recovery (up to 85%), indicating a better alternative to commercial TPEs. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 130–145     

Activity and stability spontaneously enhanced toward ethylene polymerization by employing 2‐(1‐(2,4‐dibenzhydrylnaphthylimino)ethyl)‐6‐(1‐(arylimino)ethyl) pyridyliron(II) dichlorides

A series of 2‐(1‐(2,4‐dibenzhydrylnaphthylimino)ethyl)‐6‐(1‐(arylimino)ethyl)pyridyliron(II) complexes ( Fe1 ? Fe5 ) was synthesized and characterized. The molecular structure of the representative Fe2 was determined by single‐crystal X‐ray diffraction, revealing a distorted pseudo‐square‐pyramidal geometry around the iron center. On activation with either methylaluminoxane (MAO) or modified methylaluminoxane (MMAO), all these iron complex precatalysts performed with high activities (up to 1.58 × 10⁷ g (PE) mol^?1 (Fe) h^?1) toward ethylene polymerization, producing highly linear polyethylenes with high molecular weight and bimodal distribution, which was in accordance with high temperature ¹³C NMR, high T _m values (T _m ～130 °C) and the GPC curves of the obtained polyethylenes. Meanwhile, DFT calculation results also showed the good correlation between net charges on iron and experimental activities. Compared with previous bis(imino)pyridyliron analogues, the current iron complexes containing the benzhydrylnaphthyl groups exhibited relatively higher activities and better thermal‐stability at elevated temperatures, especially at 80 °C as the industrial operating temperature, and still showed high activities toward ethylene polymerization up to 8.57 × 10⁶ g (PE) mol^?1 (Fe) h^?1 in the presence of co‐catalyst MMAO. In addition, these iron complex precatalysts all exhibited long lifetimes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 988–996     

Thermo‐stable 2‐(arylimino)benzylidene‐9‐arylimino‐5,6,7,8‐tetrahydro cyclohepta[b]pyridyliron(II) precatalysts toward ethylene polymerization and highly linear polyethylenes

A series of 2‐(arylimino)benzylidene‐9‐arylimino‐5,6,7,8‐tetrahydrocyclohepta[b] pyridyliron(II) chlorides was synthesized and characterized using FT‐IR and elemental analysis, and the molecular structures of complexes Fe3 and Fe4 have been confirmed by the single‐crystal X‐ray diffraction as a pseudo‐square‐pyramidal or distorted trigonal‐bipyramidal geometry around the iron core. On activation with methylaluminoxane (MAO) or modified methylaluminoxane (MMAO), all iron precatalysts exhibited high activities toward ethylene polymerization with a marvelous thermo‐stability and long lifetime. The Fe4 /MAO system showed highest activity of 1.56 × 10⁷ gPE·mol^?1(Fe)·h^?1 at 70 °C, which is one of the highest activities toward ethylene polymerization by iron precatalysts. Even up to 80 °C, Fe3 /MAO system still persist high activity as 6.87 × 10⁶ g(PE)·mol^?1(Fe)·h^?1, demonstrating remarkable thermal stability for industrial polymerizations (80–100 °C). This was mainly attributing to the phenyl modification of the framework of the iron precatalysts. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 830–842     

Poly(hydroxyisobutyrate) by ring‐opening polymerizations of 5,5‐dimethyl‐1,3,2‐dioxithiolan‐4‐one‐2‐oxide

α‐Hydroxyisobutyric acid anhydrosulfate HiBAS (5,5‐dimethyl‐1,3,2‐dioxithiolan‐4‐one‐2‐oxide) was polymerized under various reaction conditions and the solid reaction products were characterized by ¹H NMR spectroscopy, MALDI‐TOF mass spectrometry (MT m.s.), fast atom bombardment mass spectrometry (FAB m.s.), viscosity, and SEC measurements. Thermal polymerizations at 100 °C mainly yielded cyclic oligo polyesters presumably resulting from a zwitterionic polymerization. Cycles were also detected when pyridine was used as catalyst at 20 °C. When triethylamine was used as catalyst traces of H₂O played the role of initiators. Benzyl alcohol initiated the polymerization of HiBAS at 100 °C and yielded a polyester terminated by one benzylester and one OH endgroup. The SEC measurements indicated that all samples possess relatively low molar masses with number–average molecular weights ≤ 10,000 Da (in contrast to the literature data). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6229–6237, 2008     

Reversible addition–fragmentation chain transfer polymerization of glycidyl methacrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

A reversible addition–fragmentation chain transfer (RAFT) agent, 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN), was synthesized and applied to the RAFT polymerization of glycidyl methacrylate (GMA). The polymerization was conducted both in bulk and in a solvent with 2,2′‐azobisisobutyronitrile (AIBN) as the initiator at various temperatures. The results for both types of polymerizations showed that GMA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion up to 96.7% at 60 °C, up to 98.9% at 80 °C in bulk, and up to 64.3% at 60 °C in a benzene solution. The polymerization rate of GMA in bulk was obviously faster than that in a benzene solution. The molecular weights obtained from gel permeation chromatography were close to the theoretical values, and the polydispersities of the polymer were relatively low up to high conversions in all cases. It was confirmed by a chain‐extension reaction that the AIBN‐initiated polymerizations of GMA with CPDN as a RAFT agent were well controlled and were consistent with the RAFT mechanism. The epoxy group remained intact in the polymers after the RAFT polymerization of GMA, as indicated by the ¹H NMR spectrum. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2558–2565, 2004     

Tri‐block copolymers of polyethylene glycol and hyperbranched poly‐3‐ethyl‐3‐(hydroxymethyl)oxetane through cationic ring opening polymerization

Tri‐block copolymers of linear poly(ethylene glycol) (PEG) and hyperbranched poly‐3‐ethyl‐3‐(hydroxymethyl)oxetane (poly‐TMPO) are reported. The novel dumb‐bell shaped polyethers were synthesized in bulk with cationic ringopening polymerization utilizing BF₃OEt₂ as initiator, via drop‐wise addition of the oxetane monomer. The thermal properties of the materials were successfully tuned by varying the amount of poly‐TMPO attached to the PEG‐chains, ranging from a melting point of 54 °C and a degree of crystallinity of 76% for pure PEG, to a melting point of 35 °C and a degree of crystallinity of 12% for the polyether copolymer having an average of 14 TMPO units per PEG chain. The materials are of relatively low polydispersity, with M_n/M_w ranging from 1.2 to 1.4. The materials have been evaluated for usage with the energetic oxidizer ammonium dinitramide. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6191–6200, 2009     

Synthesis of photosensitive and thermosetting poly(phenylene ether) based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol‐co‐2,6‐dimethyl‐phenol] and a photoacid generator

A chemically amplified photosensitive and thermosetting polymer based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol (15 mol %)‐co‐2,6‐dimethylphenol (85 mol %)] ( 3c ) and a photoacid generator [(5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐(2‐methylphenyl)acetonitrile] was developed. Poly[2,6‐bis(3‐methyl‐2‐butenyl)phenol]‐co‐2,6‐dimethylphenol)] ( 3 ) with high molecular weights (number‐average molecular weight ～ 24,000) was prepared by the oxidative coupling copolymerization of 2,6‐di(3‐methyl‐2‐butenyl)phenol with 2,6‐dimethylphenol in the presence of copper(I) chloride and pyridine as the catalyst under a stream of oxygen. The structures of 3 were characterized with IR, ¹H NMR, and ¹³C NMR spectroscopy. 3 was crosslinked by a thermal treatment at 300 °C for 1 h under N₂. The 5% weight loss temperatures and glass‐transition temperatures of the cured copolymers reached around 420 °C in nitrogen and 300 °C, respectively. The average refractive index of the cured copolymer ( 3c ) film was 1.5452, from which the dielectric constant at 1 MHz was estimated to be 2.6. The resist showed a sensitivity of 35 mJ cm^?2 and a contrast of 1.6 when it was exposed to 436‐nm light, postexposure‐baked at 145 °C for 5 min, and developed with toluene at 25 °C. A fine negative image featuring 8‐μm line‐and‐space patterns was obtained on a film exposed to 100 mJ cm^?2 with 436‐nm light in the contact‐printed mode. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 149–156, 2005     

β‐Hydrogen transfer from poly(methyl methacrylate) propagating radicals to the nitroxide SG1: Analysis of the chain‐end and determination of the rate constant

Methyl methacrylate (MMA) was polymerized in bulk at 70 °C in the presence of an alkoxyamine initiator with low dissociation temperature (the so‐called BlocBuilder?) and increasing amounts of free N‐tert‐butyl‐N‐(1‐diethylphosphono‐2,2‐dimethylpropyl) nitroxide (SG1). Low final monomer conversions were reached, indicating a loss in radical activity due to side reactions such as irreversible homoterminations between the propagating radicals and β‐hydrogen transfer (also called disproportionation) from a propagating radical to a free‐SG1 nitroxide. Proton NMR and MALDI‐TOF mass spectrometry were used to analyze the polymer chain‐ends and to clearly identify the main mechanism of irreversible termination. In particular, it was shown that all polymer chains were terminated by an alkene function in the presence of a large excess of free SG1, meaning that β‐hydrogen transfer from PMMA propagating radicals to the nitroxide SG1 was the major chain‐stopping event. On the other hand, for a low excess of free SG1, the two termination modes coexisted. Kinetic modeling was then performed using the PREDICI software, and the rate constant of β‐hydrogen transfer, k_βHtr, was estimated to be 1.69 × 10³ L mol^?1 s^?1 at 70 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6333–6345, 2008     

Copper(0)‐mediated living radical polymerization of acrylonitrile at room temperature

The copper(0)‐catalyzed living radical polymerization of acrylonitrile (AN) was investigated using ethyl 2‐bromoisobutyrate as an initiator and 2,2′‐bipyridine as a ligand. The polymerization proceeded smoothly in dimethyl sulphoxide with higher than 90% conversion in 13 h at 25 °C. The polymerization kept the features of controlled radical polymerization. ¹H NMR spectra proved that the resultant polymer was end‐capped by ethyl 2‐bromoisobutyrate species. Such polymerization technique was also successfully introduced to conduct the copolymerization of styrene (St) and AN to obtain well‐controlled copolymers of St and AN at 25 °C, in which the monomer conversion of St could reach to higher than 90%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Ring‐Opening and polymerization of 1‐[2′‐(heptaphenylcyclotetrasiloxanyl)ethyl]‐1,3,3,5,5‐pentamethylcyclotrisiloxane

1‐[2′‐(Heptaphenylcyclotetrasiloxanyl)ethyl]‐1,3,3,5,5‐pentamethylcyclotetrasiloxane ( II ) was prepared from 1‐[2′‐(methyldichlorosilyl)ethyl]‐1,3,3,5,5,7,7‐heptaphenylcyclotetrasiloxane ( I ) and tetramethyldisiloxane‐1,3‐diol. Acid‐catalyzed ring‐opening of II in the presence of tetramethyldisiloxane gave 1,9‐dihydrido‐5‐[2′‐(heptaphenylcyclotetrasiloxanyl)ethyl]nonamethylpentasiloxane ( III ) and 1,9‐dihydrido‐3‐[2′‐(heptaphenylcyclotetrasiloxanyl)ethyl]nonamethylpentasiloxane ( IV ). Both acid‐ and base‐catalyzed ring‐opening polymerization of II gives highly viscous, transparent polymers. The structures of I – IV and polymers were determined by UV, IR, ¹H, ¹³C, and ²⁹Si NMR spectroscopy. In addition, molecular weights obtained by GPC and NMR end group analysis were confirmed with mass spectrometry. On the basis of ²⁹Si NMR spectroscopy, the polymers appear to result exclusively from ring‐opening of the cyclotrisiloxane ring. No evidence for ring‐opening of the cyclotetrasiloxane ring was observed. Polymer properties were determined by DSC and TGA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 137–146, 2006     

Ring‐opening polymerization of 1,3‐benzoxazines by p‐toluenesulfonates as thermally latent initiators

p‐Toluenesulfonic acid (TsOH) and several alkyl p‐toluenesulfonates, that is, methyl p‐toluenesulfonate (TsOMe), cyclohexyl p‐toluenesulfonate (TsOCH), and neopentyl p‐toluenesulfonate (TsONP), were evaluated as initiators for the ring‐opening polymerization of benzoxazines. TsOH and TsOMe were highly efficient initiators that induced the polymerization at 60 and 80 °C, respectively. In contrast, TsOCH and TsONP did not initiate the polymerization below 100 °C, while they induced the polymerization at elevated temperatures, 120 and 150 °C, respectively. When TsOCH was used as an initiator, the corresponding polymerization rate was comparable to that observed for the polymerization with using TsOH as an initiator. These results suggested that neutral TsOCH and TsONP can be regarded as “thermally latent initiators,” which underwent the thermal dissociation at the elevated temperatures to generate the corresponding alkyl cations and/or TsOH as the initiators of the polymerization. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

1‐(2,6‐dibenzhydryl‐4‐fluorophenylimino)‐2‐aryliminoacenaphthylylnickel halides highly polymerizing ethylene for the polyethylenes with high branches and molecular weights

A series of 1‐(2,6‐dibenzhydryl‐4‐fluorophenylimino)‐ 2‐aryliminoacenaphthylene derivatives ( L1–L5 ) and their halonickel complexes LNiX₂ (X = Br, Ni1–Ni5 ; X = Cl, Ni6–Ni10 ) are synthesized and well characterized. The molecular structures of representative complexes Ni2 and Ni4 are confirmed as the distorted tetrahedron geometry around nickel atom by the single crystal X‐ray diffraction. Upon activation with methylaluminoxane, all nickel complexes show high activities up to 1.49 × 10⁷ g of PE (mol of Ni)^?1 h^?1 toward ethylene polymerization, producing polyethylenes with high branches and molecular weights up to 1.62 × 10⁶ g mol^?1 as well as narrow polydispersity. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1369–1378     

Synthesis of 9,9‐bis(4‐aminophenyl)fluorene‐based benzoxazine and properties of its high‐performance thermoset

A benzoxazine ( P‐bapf ) based on 9,9‐bis(4‐aminophenyl)fluorene (BAPF), phenol, and formaldehyde was successfully prepared using two‐pot and one‐pot procedures. In the two‐pot approach, BAPF initially reacted with 2‐hydroxybenzaldehyde, leading to 9,9‐bis(4‐(2‐hydroxybenzylideneimino)phenyl)fluorene. The imine linkages of 9,9‐bis(4‐(2‐hydroxybenzylideneimino)phenyl)fluorene were then reduced by sodium borohydride, forming 9,9‐bis(4‐(2‐hydroxybenzylamino)phenyl)fluorene. Finally, paraformaldehyde was added to induce ring closure condensation, forming benzoxazine ( P‐bapf ). In the one‐pot approach, P‐bapf was obtained directly by reacting BAPF, phenol, and paraformaldehyde in various solvents. Among the solvents, we found that using toluene/ethanol (2/1, v/v) as a solvent leads to the best purity and yield. No gelation was observed in the preparation. The structure of the resulting benzoxazine was confirmed by ¹H, ¹³C, ¹H? ¹H and ¹H? ¹³C NMR spectra. P‐bapf exhibits a photoluminescent emission at 395 nm under an excitation of 275 nm. After curing, the resulting P‐bapf thermoset exhibits T_g as high as 236 °C, and the T_g can be further increased to 260 °C by copolymerization with an equal equivalent of cresol novolac epoxy. The 5% degradation temperature of the P‐bapf thermoset reaches as high as 413 °C (N₂) and 431 °C (air). The refractive index at 589 nm is as high as 1.70, demonstrating a high refractive index characteristic of fluorene linkage. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Titanium complexes based on aminodiol ligands for the ring‐opening polymerization of ε‐caprolactone,rac‐β‐butyrolactone,and trimethylene carbonate

Several titanium complexes based on aminodiol ligands were tested as initiators for the ring‐opening polymerization (ROP) of ε‐caprolactone under solution and bulk conditions. All complexes were found to be efficient under both conditions. For bulk polymerization at 70 °C, high activities were observed (113.3–156.2 g_poly mmol_cat^?1 h^?1) together with controlled molar mass distribution. Kinetic studies revealed controlled polymerization, and the chain propagation was first order with respect to monomer conversion. One complex was also tested for the ROP of rac‐β‐butyrolactone and the end‐group analysis suggested that ring opening occurs through acyl‐oxygen bond cleavage via coordination–insertion mechanism. The microstructure analysis of polymer by ¹³C NMR indicates atactic polymer. Another complex was also found to be efficient initiator for the ROP of trimethylene carbonate under solution and bulk conditions. Again, end‐group analysis suggests coordination–insertion mechanism. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Ring‐opening copolymerization of ethylene carbonate and ε‐caprolactone catalyzed by neodymium tris(2,6‐di‐tert‐butyl‐4‐methylphenolate): Synthesis,characterization, and dynamic mechanic analysis

The ring‐opening copolymerization of ethylene carbonate (EC) with ε‐caprolactone (CL) was carried out using neodymium tris(2,6‐di‐tert‐butyl‐4‐methylphenolate) as a single‐component catalyst. Copolymers containing up to 22.0% EC contents with high molecular weights (up to 23.97 × 10⁴) and moderate molecular weight distributions (between 1.66 and 2.03) were synthesized at room temperature. Compared with homopoly(ε‐caprolactone), the copolymers with EC units exhibited increased glass transition temperatures (?35.6 °C), reduced melting temperatures (44.5 °C), and greatly enhanced elongation percentage at break (2383%) based on dynamic mechanic analysis. The crystallinities of the copolymers decreased with the increasing EC molar percentage in the products. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4050–4055, 2008     

Acid‐promoted double ring‐opening reaction of bicyclobis (γ‐butyrolactone) with alcohol and its application to polyester synthesis

Bicyclobis(γ‐butyrolactone) (BBL) bearing methyl group 1a reacted with benzyl alcohol (BnOH) in the presence of p‐toluenesulfonic acid (p‐TsOH) through the double ring‐opening of the bislactone structure to afford the corresponding adduct 2a bearing carboxyl group. The resulting carboxyl group underwent condensation with BnOH to afford the corresponding diester 3a . The second step was quite slow at ambient temperature; however, it was efficiently accelerated by elevating temperature to 120 °C or performing under reduced pressure at 80 °C to afford 3a in an excellent yield. Based on these results, the reaction of 1a with xylene‐α,α‐diol (XyD) was carried out in chlorobenzene at 120 °C to obtain the corresponding polyester bearing ketone group in the side chain. The condensation reaction in the second step was effectively promoted by simultaneous removal of water under reduced pressure. BBLs 1b and 1c bearing reactive groups, isopropenyl and chloromethyl, respectively, were also employed as monomers efficiently. Their reactions with XyD gave the corresponding reactive polyesters bearing methacryloyl and chloroacetyl moieties, respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Fluorene‐rich high performance polyesters: Synthesis and characterization of 9,9‐fluorenylidene and 2,7‐fluorenylene‐based polyesters with excellent optical property

Polyesters PEs containing high content of fluorene units in their backbones were synthesized from 9,9‐diarene‐substituted fluorene diols ( 1 ) and fluorene‐based diacid chlorides ( 2 ) by high temperature polycondensation at 185 °C in diphenyl ether. The molecular weights of the polyesters PE1‐PE5 were in a range of M_w 25,000–165,000. The polyesters displayed their high thermostability: the glass transition temperatures (T_g) by differential scanning calorimetry analysis ranged from 109 to 217 °C, while the 10% weight loss temperatures (T_d10) measured by thermogravimetric analysis were over 400 °C in nitrogen and 395 °C in air. The polyesters had good solubility in most common organic solvents such as chloroform and toluene and gave tough, transparent and flexible cast films. The transmittance of the films was over 80% in the wavelength range from 450 to 700 nm in any PEs . The PEs exhibited high refractive index values around 1.65, while they had very low degree of birefringence. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2549–2556, 2008     

Nitroxide‐mediated radical copolymerization of methyl methacrylate controlled with a minimal amount of 9‐(4‐vinylbenzyl)‐9H‐carbazole

The controlled nitroxide‐mediated homopolymerization of 9‐(4‐vinylbenzyl)‐9H‐carbazole (VBK) and the copolymerization of methyl methacrylate (MMA) with varying amounts of VBK were accomplished by using 10 mol % {tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino} nitroxide relative to 2‐({tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino}oxy)‐2‐methylpropionic acid (BlocBuilder?) in dimethylformamide at temperatures from 80 to 125 °C. As little as 1 mol % of VBK in the feed was required to obtain a controlled copolymerization of an MMA/VBK mixture, resulting in a linear increase in molecular weight versus conversion with a narrow molecular weight distribution (M_w /M_n ≈ 1.3). Preferential incorporation of VBK into the copolymer was indicated by the MMA/VBK reactivity ratios determined: r_VBK = 2.7 ± 1.5 and r_MMA = 0.24 ± 0.14. The copolymers were found significantly “living” by performing subsequent chain extensions with a fresh batch of VBK and by ³¹P NMR spectroscopy analysis. VBK was found to be an effective controlling comonomer for NMP of MMA, and such low levels of VBK comonomer ensured transparency in the final copolymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Rigid‐rod polyamides and polyimides prepared from 4,3″‐diamino‐2′,6′‐di(2‐naphthyl)‐p‐terphenyl and 2′,6′,3‴,5‴‐tetra(2‐naphthyl)‐4,4″‐diamino‐p‐quinquephenyl

A series of rigid‐rod polyamides and polyimides containing p‐terphenyl or p‐quinquephenyl moieties in backbone as well as naphthyl pendent groups were synthesized from two new aromatic diamines. The polymers were characterized by inherent viscosity, elemental analysis, FT‐IR, ¹H‐NMR, ¹³C‐NMR, X‐ray, differential scanning calorimetry (DSC), thermomechanical analysis (TMA), thermal gravimetric analysis (TGA), isothermal gravimetric analysis, and moisture absorption. All polymers were amorphous and displayed T_g values at 304–337°C. Polyamides dissolved upon heating in polar aprotic solvents containing LiCl as well as CCl₃COOH, whereas polyimides were partially soluble in these solvents. No weight loss was observed up to 377–422°C in N₂ and 355–397°C in air. The anaerobic char yields were 57–69% at 800°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 15–24, 1999     

Synthesis and application as polymer electrolyte of hyperbranched polyether made by cationic ring‐opening polymerization of 3‐{2‐[2‐(2‐hydroxyethoxy)ethoxy]ethoxymethyl}‐3′‐methyl‐oxetane

A novel cyclic ether monomer 3‐{2‐[2‐(2‐hydroxyethoxy)ethoxy]ethoxy‐methyl}‐3′‐methyloxetane (HEMO) was prepared from the reaction of 3‐hydroxymethyl‐3′‐methyloxetane tosylate with triethylene glycol. The corresponding hyperbranched polyether (PHEMO) was synthesized using BF₃·Et₂O as initiator through cationic ring‐opening polymerization. The evidence from ¹H and ¹³C NMR analyses revealed that the hyperbranched structure is constructed by the competition between two chain propagation mechanisms, i.e. active chain end and activated monomer mechanism. The terminal structure of PHEMO with a cyclic fragment was definitely detected by MALDI‐TOF measurement. A DSC test implied that the resulting polyether has excellent segment motion performance potentially beneficial for the ion transport of polymer electrolytes. Moreover, a TGA assay showed that this hyperbranched polymer possesses high thermostability as compared to its liquid counterpart. The ion conductivity was measured to reach 5.6 × 10^?5 S/cm at room temperature and 6.3 × 10^?4 S/cm at 80 °C after doped with LiTFSI at a ratio of Li:O = 0.05, presenting the promise to meet the practical requirement of lithium ion batteries for polymer electrolytes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3650–3665, 2006