Polymer brushes grafted from graphene via bioinspired polydopamine chemistry and activators regenerated by electron transfer atom transfer radical polymerization

Polymer brushes decorated reduced GO (rGO) with advanced applications have been prepared by bioinspired polydopamine (PDA) chemistry integrated with activators regenerated by electron transfer atom transfer radical polymerization (ARGET‐ATRP) technique. First, rGO/PDA was obtained by the process for graphene oxide (GO) coated with a homogeneous bio‐adhesive PDA layer. Then the initiator 2‐bromoisobutyryl bromide (BIBB) was immobilized on the surface of PDA functionalized rGO. Finally, rGO/PDA‐Br was polymerized with N, N‐diethylaminoethyl methacrylate (DEAEMA) and glycidyl methacrylate (GMA) to obtain rGO/PDA‐g‐polymer brushes by ARGET‐ATRP process. The prepared rGO/PDA‐g‐PGMA brush would be subjected to further functionalization with ethylenediamine (EDA), which would impart the obtained products (rGO/PDA‐g‐PGMA‐NH₂) with good adsorption ability toward cationic dyes. The chemical structures and morphologies of the functionalized GO products have been characterized in detail by Fourier transform infrared spectroscopy (FTIR), X‐ray photoelectron spectroscopy (XPS), Raman spectroscopy, thermal gravimetric analysis (TGA), scanning electron microscope (SEM), transmission electron microscope(TEM), and atomic force microscopy (AFM). The distinctive pH‐responsive character of rGO/PDA‐g‐PDEAEMA and adsorption ability of rGO/PDA‐g‐PGMA‐NH₂ for cationic dyes have been explored by UV–vis spectrophotometer. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 689–698     

Atom transfer radical polymerization using activators regenerated by electron transfer of acrylonitrile in 1‐(1‐ethoxycarbonylethyl)‐3‐methylimidazolium hexafluorophospate

Atom transfer radical polymerization using activators regenerated by electron transfer (ARGET ATRP) of acrylonitrile (AN) was first approached with 1‐(1‐ethoxycarbonylethyl)‐3‐methylimidazolium tetrafluoroborate ([ecemim][BF₄]) as reaction medium and tin(II) bis(2‐ethylhexanoate) (Sn(EH)₂) as reducing agent in the presence of air. When compared with in bulk, an obvious increase of polymer isotacticity was observed for ARGET ATRP of AN in 1‐(1‐ethoxycarbonylethyl)‐3‐methylimidazolium hexafluorophospate ([ecemim][PF₆]), the reaction rate of ARGET ATRP of AN in [ecemim][PF₆] was higher and the polymerization process was better controlled. The block copolymer polyacrylonitrile‐block‐poly(methyl methacrylate) with molecular weight at 69,750, distribution at 1.34, and isotacticity at 0.36 was successfully obtained in [ecemim][PF₆]. [Ecemim][PF₆] and the catalyst system were recycled and reused and had no effect on the living nature of polymerization. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Functionalization of multiwalled carbon nanotube via surface reversible addition fragmentation chain transfer polymerization and as lubricant additives

Polymer‐grafted multiwalled carbon nanotube (MWCNT) hybrid composite which possess a hard backbone of MWCNT and a soft shell of brush‐like polystyrene (PSt) were synthesized. The reversible addition fragmentation chain transfer (RAFT) agents were successfully immobilized onto the surface of MWCNT first, and PSt chains were subsequently grafted from sidewall of MWCNT via RAFT polymerization. Chemical structure of resulting product and the quantities of grafted polymer were determined by Fourier transform infrared, thermal gravimetric analysis, nuclear magnetic resonance, and X‐ray photoelectron spectra. Transmission electron microscopy and field emission scanning electron microscopy images clearly indicate that the nanotubes were coated with a polymer layer. Furthermore, the functionalized MWCNT as additives was added to base lubricant and the tribological property of resultant MWCNT lubricant was investigated with four‐ball machines. The results indicate that the functionalization led to an improvement in the dispersion of MWCNT and as additives it amended the tribological property of base lubricant. The mechanism of the significant improvements on the tribological properties of the functionalized MWCNT as additives was discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3014–3023, 2008     

Synthesis of random polyampholyte brushes by atom transfer radical polymerization

We report the synthesis of random polyampholyte brushes containing 2‐(dimethylamino)ethyl methacrylate (DMAEMA) and methacrylic acid (MAA). The preparation of polyampholyte brushes is performed by the “grafting from” strategy using surface‐initiated atom transfer radical polymerization (ATRP). The first step consists in the formation of the self‐assembled monolayer of the ATRP initiator. Secondly, the chains are grown from the surface by controlled/“living” radical polymerization. The random copolymer brushes and the corresponding homopolymers brushes containing 2‐(dimethylamino)ethyl methacrylate and tert‐butyl methacrylate (^tBuMA) are prepared. The last step is the deprotection of the ^tBuMA form to the MAA segment by in situ hydrolysis reaction. The annealed DMAEMA group can also be converted to the quenched form by in situ quaternization reaction. This results in the formation of “annealed” and “semiannealed” polyampholyte brushes. The “annealed” polyampholyte corresponds to the random copolymer that contains only annealed units, weak acid and weak base. The “semiannealed” polyampholyte consists of the mixture of annealed (weak acid) and quenched (quaternized segment) units. Polyampholyte brushes with various grafting densities are synthesized and carefully characterized using surface techniques such as ellipsometry and FTIR‐ATR. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4305–4319, 2008     

Light‐driven atom transfer radical polymerization on supramolecular complexes of conjugated polymers and single‐walled carbon nanotubes

Previous approaches used to decorate latently reactive conjugated polymer‐coated carbon nanotube complexes have utilized “grafting‐to” strategies. Here, we coat the carbon nanotube surface with a conjugated polymer whose side chains contain the radical initiator, α‐bromoisobutyrate, which enables atom transfer radical polymerization (ATRP) from the polymer–nanotube surface. Using light to generate Cu(I) in situ, ATRP is used to grow narrow dispersity polymer chains from the polymer–nanotube surface. We confirm the successful polymerization of (meth)acrylates from the polymer–nanotube surface using a combination of gel permeation chromatography and infrared spectroscopy. Strikingly, we demonstrate that nanotube optoelectronic properties are preserved after radical‐mediated polymer grafting using Raman spectroscopy and photoluminescence mapping. Overall, this work elucidates a method to grow narrow dispersity polymer chains from the polymer–nanotube surface using light‐driven radical chemistry, with concurrent preservation of nanotube optoelectronic properties. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2015–2020     

Functionalization and patterning of reactive polymer brushes based on surface reversible addition and fragmentation chain transfer polymerization

We present the synthesis of reactive polymer brushes prepared by surface reversible addition–fragmentation chain transfer polymerization of pentafluorophenyl acrylate. The reactive ester moieties can be used to functionalize the polymer brush film with virtually any functionality by simple post‐polymerization modification with amines. Dithiobenzoic acid benzyl‐(4‐ethyltrimethoxylsilyl) ester was used as the surface chain transfer agent (S‐CTA) and the anchoring group onto the silicon substrates. Reactive polymer brushes with adjustable molecular weight, high grafting density, and conformal coverage through the grafting‐from approach were obtained. Subsequently, the reactive polymer brushes were converted with amino‐spiropyrans resulting in reversible light‐responsive polymer brush films. The wetting behavior could be altered by irradiation with ultraviolet (UV) or visible light. Furthermore, a patterned surface of polymer brushes was obtained using a lithography technique. UV irradiation of the S‐CTA‐modified substrates leads to a selective degradation of S‐CTA in the exposed areas and gives patterned activated polymer brushes after a subsequent RAFT polymerization step. Conversion of the patterned polymer brushes with 5‐((2‐aminoethyl)amino)naphthalene‐1‐sulfonic acid resulted in patterned fluorescent polymer brush films. The utilization of reactive polymer brushes offers an easy approach in the fabrication of highly functional brushes, even for functionalities whose introduction is limited by other strategies. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Regulating Gelation Time and Kinetics Analysis Based on the ARGET ATRP Mechanism

A novel activators regenerated by electron transfer (ARGET) atom transfer radical polymerization (ATRP) initiation system composing of an initiator sodium chloroacetate, a catalyst ferric chloride, and a reducing agent ascorbic acid was developed to improve the gelation time of the in situ crosslinked polymer system. The kinetics of polymerization of acrylamide showed features of a living/controlled process in which the concentrations of the growing radicals [P·] are kept constant throughout the polymerization process. Compared with conventional potassium persulfate initiators, the gelation time of the in situ crosslinked polymer system can be improved to 40 h or even longer using the ARGET ATRP initiation system at 80 °C due to the low radical concentration and slow polymerization reaction. Core flooding test showed that the ARGET ATRP initiating system developed could initiate the polymerization reaction of the in situ crosslinked polymer system in the core. However, the gelation time was extended in comparison to that of the result obtained in the bottle, resulting from the dilution and adsorption of ARGET ATRP components during the injection process. The research expands the application field of the ARGET ATRP principle and has a promising prospect on controlling the gelation time of the in situ crosslinked polymer system. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 519–527     

Polymer brushes via surface-initiated polymerizations

Polymer brushes produced by controlled surface-initiated polymerization provide a route to surfaces coated with well-defined thin polymer films that are covalently bound to the substrate. All of the major controlled polymerization techniques have been applied to the synthesis of polymer brushes and examples of each are presented here. Many examples of brush synthesis in the literature have used the living atom transfer radical polymerization (ATRP) system, and in this tutorial review a particular focus is given to examples of this technique.     

Comparison of surface confined ATRP and SET‐LRP syntheses for a series of amino (meth)acrylate polymer brushes on silicon substrates

A series of poly(amino (meth)acrylate) brushes, poly(2‐(dimethylamino)ethyl methacrylate) (PDMAEMA), poly(2‐(diethylamino)ethyl methacrylate) (PDEAEMA), poly(2‐(dimethylamino)ethyl acrylate) (PDMAEA), poly(2‐(tert‐butylamino)ethyl methacrylate) (PTBAEMA), has been synthesized via surface‐confined controlled/living radical polymerizations using surface‐confined initiator from silane self‐assembled monolayers (SAMs) on silicon (Si) wafer substrates. Chemical methods and efficacies for two types of living radical polymerization, atom transfer radical (ATRP) and single electron transfer (SET‐LRP), are described and contrasted for the surface confined polymerization of poly(amino (meth)acrylate)s. Effects of solvent, catalyst/ligand system, and temperature on polymerization success were examined. Chemical compositions after each reaction step were characterized with FTIR spectroscopy, contact angle goniometry, and X‐ray photoelectron spectroscopy while the SAM and polymer brush thicknesses were measured with spectroscopic ellipsometry. For the first time, this study demonstrates successful surface‐confined polymerization of a series of poly(amine (meth)acrylate) brushes from Si‐SAM substrates using a copper metal electron donor catalyst. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6552–6560, 2009     

The synthesis of water‐soluble PHEMA via ARGET ATRP in protic media

2‐Hydroxyethyl methacrylate has been polymerized in methanol using activators regenerated by electron transfer (ARGET) atom transfer radical polymerization (ATRP), to produce water‐soluble poly(2‐hydroxyethyl methacrylate) (PHEMA). The various parameters that determine control of the living polymerization have been explored. Using the Cu(II)/TPMA catalyst system (TPMA = tris(2‐pyridylmethyl)amine), controlled polymerization was achieved with Cu concentrations as low as 50 ppm relative to HEMA, with a [TPMA]/[Cu(II)] ratio of 5. Use of hydrazine as the reducing agent generally gave better control of polymerization than use of ascorbic acid. The polymerization conditions were tolerant of small amounts of air, and colorless polymers were easily isolated by simple precipitation and washing steps. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4084–4092, 2010     

Atom transfer radical polymerization of functional monomers employing Cu‐based catalysts at low concentration: Polymerization of glycidyl methacrylate

Initiators for continuous activator regeneration atom transfer radical polymerization (ICAR ATRP) of an epoxide‐containing monomer, glycidyl methacrylate (GMA), was successfully carried out using low concentration of catalyst (ca. 105 ppm) at 60 °C in anisole. The copper complex of tris(2‐pyridylmethyl)amine was used as the catalyst, diethyl 2‐bromo‐2‐methylmalonate as the initiator, and 2,2′‐azobisisobutyronitrile as the reducing agent. When moderate degrees of polymerization were targeted (up to 200), special purification of the monomer, other than removal of the polymerization inhibitor, was not required to achieve good control. To synthesize well‐defined polymers with higher degrees of polymerization (600), it was essential to use very pure monomer, and polymers of molecular weights exceeding 50,000 g mol^?1 and M_w/M_n = 1.10 were prepared. The developed procedures were used to chain‐extend bromine‐terminated poly(methyl methacrylate) macroinitiator prepared by activators regenerated by electron transfer (ARGET) ATRP. The Sn^II‐mediated ARGET ATRP technique was not suitable for the polymerization of GMA and resulted in polymers with multimodal molecular weight distributions. This was due to the occurrence of epoxide ring‐opening reactions, catalyzed by Sn^II and Sn^IV. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Cytocompatible Polymer Grafting from Individual Living Cells by Atom‐Transfer Radical Polymerization

A cytocompatible method of surface‐initiated, activator regenerated by electron transfer, atom transfer radical polymerization (SI‐ARGET ATRP) is developed for engineering cell surfaces with synthetic polymers. Dopamine‐based ATRP initiators are used for both introducing the ATRP initiator onto chemically complex cell surfaces uniformly (by the material‐independent coating property of polydopamine) and protecting the cells from radical attack during polymerization (by the radical‐scavenging property of polydopamine). Synthetic polymers are grafted onto the surface of individual yeast cells without significant loss of cell viability, and the uniform and dense grafting is confirmed by various characterization methods including agglutination assay and cell‐division studies. This work will provide a strategic approach to the generation of living cell–polymer hybrid structures and open the door to their application in multitude of areas, such as sensor technology, catalysis, theranostics, and cell therapy.     

Synthesis of well‐defined polymer brushes on the surface of zinc antimonate nanoparticles through surface‐initiated atom transfer radical polymerization

Zinc antimonate nanoparticles consisting of antimony and zinc oxide were surface modified in a methanol solvent medium using triethoxysilane‐based atom transfer radical polymerization (ATRP) initiating group (i.e.,) 6‐(2‐bromo‐2‐methyl) propionyloxy hexyl triethoxysilane. Successful grafting of ATRP initiator on the surface of nanoparticles was confirmed by thermogravimetric analysis that shows a significant weight loss at around 250–410 °C. Grafting of ATRP initiator onto the surface was further corroborated using Fourier transform Infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS). The surface‐initiated ATRP of methyl methacrylate (MMA) mediated by a copper complex was carried out with the initiator‐fixed zinc antimonate nanoparticles in the presence of a sacrificial (free) initiator. The polymerization was preceded in a living manner in all examined cases; producing nanoparticles coated with well defined poly(methyl methacrylate) (PMMA) brushes with molecular weight in the range of 35–48K. Furthermore, PMMA‐grafted zinc antimonate nanoparticles were characterized using Thermogravimetric analysis (TGA) that exhibit significant weight loss in the temperature range of 300–410 °C confirming the formation of polymer brushes on the surface with the graft density as high as 0.26–0.27 chains/nm². The improvement in the dispersibility of PMMA‐grafted zinc antimonate nanoparticles was verified using ultraviolet‐visible spectroscopy and transmission electron microscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Stimuli‐responsive diblock copolymer brushes via combination of “click chemistry” and living radical polymerization

pH‐ and temperature‐responsive poly(N‐isopropylacrylamide‐block?4‐vinylbenzoic acid) (poly(NIPAAm‐b‐VBA)) diblock copolymer brushes on silicon wafers have been successfully prepared by combining click reaction, single‐electron transfer‐living radical polymerization (SET‐LRP), and reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. Azide‐terminated poly(NIPAAm) brushes were obtained by SET‐LRP followed by reaction with sodium azide. A click reaction was utilized to exchange the azide end group of a poly(NIPAAm) brushes to form a surface‐immobilized macro‐RAFT agent, which was successfully chain extended via RAFT polymerization to produce poly(NIPAAm‐b‐VBA) brushes. The addition of sacrificial initiator and/or chain‐transfer agent permitted the formation of well‐defined diblock copolymer brushes and free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. Ellipsometry, contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy were used to characterize the immobilization of initiator on the silicon wafer, poly(NIPAAm) brush formation via SET‐LRP, click reaction, and poly(NIPAAm‐b‐VBA) brush formation via RAFT polymerization. The poly(NIPAAm‐b‐VBA) brushes demonstrate stimuli‐responsive behavior with respect to pH and temperature. The swollen brush thickness of poly(NIPAAm‐b‐VBA) brush increases with increasing pH, and decreases with increasing temperature. These results can provide guidance for the design of smart materials based on copolymer brushes. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2677–2685     

Novel UV initiator for functionalization of multiwalled carbon nanotubes by atom transfer radical polymerization applied on two different grades of nanotubes

A novel nonoxidative method for preparation of functionalized multiwalled carbon nanotubes (MWCNT) has been developed based on a UV sensitive initiator for atom transfer radical polymerization (ATRP). The method has been investigated with respect to ligands and polymerization time for the preparation of polystyrene functionalized MWCNT. It was found that pentamethyldiethylenetriamine (PMDETA) gave superior results with higher loading in shorter polymerization time. A comparative study of the method applied on two different grades of nonoxidized MWCNT has been performed, illustrating large differences in reactivity and polymer loading, underlining the importance of the choice of MWCNT starting material. In addition to styrene, also poly(ethylene glycol) methacrylate (PEGMA) was shown to polymerize from the surface of the MWCNT. Finally, initial results from composites of polystyrene or polyphenylenesulfide are presented. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Facile one‐pot method of initiator fixation for surface‐initiated atom transfer radical polymerization on carbon hard spheres

An efficient and novel one‐pot process is developed to immobilize the atom transfer radical polymerization (ATRP) initiators onto the surface of fully pyrolyzed carbon hard spheres (CHSs) via a radical trapping process from the in situ thermal decomposition of bis(bromomethylbenzoyl)peroxide. The CHSs do not require any additional preparative treatment prior to the initiator immobilization. Styrene and methyl methacrylate are polymerized onto initiator‐immobilized CHSs by surface‐initiated atomic transfer radical polymerization (SI‐ATRP). Samples are characterized using Fourier transform infrared, thermogravimetric analysis, scanning electron microscopy, and transmission electron microscopy. These methods of characterization confirmed that all the CHSs are coated with a uniform layer of grafted polymer. This efficient, one‐pot immobilization of ATRP‐initiators represents an exceptionally simple route for the rapid preparation of various polymer‐coated carbon‐based nanomaterials using SI‐ATRP. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3314–3322     

Synthesis and characterization of surface-initiated polymer brush prepared by reverse atom transfer radical polymerization

Surface-initiated reverse atom transfer radical polymerization (reverse ATRP) technique was used to synthesize well-controlled nanostructure of polymer brushes from silicon wafer. Kinetic studies revealed a linear increase in polymer film thickness with reaction time, indicating that chain growth from surface was a controlled process with a “living” characteristic. This technique provides a simple and efficient approach to create various nanostructures of polymer brushes potentially used for designing nanodevices. Analysis of the polymer brush layers was conducted using ellipsometry, XPS, AFM and contact angle measurements, respectively.     

Fuzzy ternary particle systems by surface-initiated atom transfer radical polymerization from layer-by-layer colloidal core-shell macroinitiator particles

We report the synthesis of ternary polymer particle material systems composed of (a) a spherical colloidal particle core, coated with (b) a polyelectrolyte intermediate shell, and followed by (c) a grafted polymer brush prepared by surface-initiated polymerization as the outer shell. The layer-by-layer (LbL) deposition process was utilized to create a functional intermediate shell of poly(diallyl-dimethylammonium chloride)/poly(acrylic acid) multilayers on the colloid template with the final layer containing an atom transfer radical polymerization (ATRP) macroinitiator polyelectrolyte. The intermediate core-shell architecture was analyzed with FT-IR, electrophoretic mobililty (zeta-potential) measurements, atomic force microscopy, and transmission electron microscopy (TEM) techniques. The particles were then utilized as macroinitiators for the surface-initiated ATRP grafting process for poly(methyl methacrylate) polymer brush. The polymer grafting was confirmed with thermo gravimetric analysis, FT-IR, and TEM. The polymer brush formed the outermost shell for a ternary colloidal particle system. By combining the LbL and surface-initiated ATRP methods to produce controllable multidomain core-shell architectures, interesting functional properties should be obtainable based on independent polyelectrolyte and polymer brush behavior.     

Atom transfer radical polymerization directly from poly(vinylidene fluoride): Surface and antifouling properties

The direct preparation of grafting polymer brushes from commercial poly (vinylidene fluoride) (PVDF) films with surface‐initiated atom transfer radical polymerization (ATRP) is demonstrated. The direct initiation of the secondary fluorinated site of PVDF facilitated grafting of the hydrophilic monomers from the PVDF surface. Homopolymer brushes of 2‐(N,N‐dimethylamino)ethyl methacrylate (DMAEMA) and poly (ethylene glycol) monomethacrylate (PEGMA) were prepared by ATRP from the PVDF surface. The chemical composition and surface topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy, attenuated total reflectance/Fourier transform infrared spectroscopy, and atomic force microscopy. A kinetic study revealed a linear increase in the graft concentration of poly[2‐(N,N‐dimethylamino)ethyl methacrylate] (PDMAEMA) and poly[poly(ethylene glycol) monomethacrylate] (PPEGMA) with the reaction time, indicating that the chain growth from the surface was consistent with a controlled or living process. The living chain ends were used as macroinitiators for the synthesis of diblock copolymer brushes. The water contact angles on PVDF films were reduced by the surface grafting of DMAEMA and PEGMA. Protein adsorption experiments revealed a substantial antifouling property of PPEGMA‐grafted PVDF films and PDMAEMA‐grafted PVDF films in comparison with the pristine PVDF surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3434–3443, 2006     

Hydrobromination of residual vinyl groups on divinylbenzene polymer particles followed by atom transfer radical surface graft polymerization

Rigid and monodisperse spherical polymer particles with 2.36 ± 0.18 μm diameter containing residual surface vinyl groups were prepared by photoinitiated precipitation polymerization of divinylbenzene. Anti‐Markovnikov addition of HBr to the surface vinyl groups yielded a 2‐bromoethyl functionality that was used as macroinitiator for atom transfer radical polymerization (ATRP), providing the possibility for further functionalization by controlled “grafting from” processes. This was demonstrated by grafting of glycidyl methacrylate brushes from the particle surface, using an ATRP system based on CuBr and pentamethyl diethylenetriamine. Existence of a methacrylic overlayer was verified by FTIR and XPS measurements, and the grafted particles were easily dispersed in water, confirming conversion of the particle surface from hydrophobic to hydrophilic. Hydrobromination of residual vinyl groups yields a macroinitiator that can be used for grafting of glycidyl methacrylate by ATRP. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1259–1265, 2009