Atom transfer radical polymerization of styrene in toluene/water mixtures

The atom transfer radical polymerization (ATRP) of styrene in water/toluene mixtures was studied. A linear dependence of the molecular weight on conversion was observed, but the initiation efficiency decreased when the catalyst concentration increased. The variation of the amount of water in the system affected the control of the ATRP, indicating that the presence of the aqueous phase influenced the concentration of copper halides in the organic phase. The partitioning of copper halides resulted in almost complete migration of Cu^II into the aqueous phase, which assisted with catalyst removal after polymerization. For example, the amount of residual copper in the organic phase determined by inductively coupled plasma was less than 1 ppm when the polymerization mixture was exposed to air for 30 min. The ATRP of styrene in water/toluene mixtures occurred with the preservation of Br at the polymer chain end, as confirmed by successful block copolymerization. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3153–3160, 2002     

Synthesis of diblock copolymers by combining stable free radical polymerization and atom transfer radical polymerization

A stable nitroxyl radical functionalized with an initiating group for atom transfer radical polymerization (ATRP), 4‐(2‐bromo‐2‐methylpropionyloxy)‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy (Br‐TEMPO), was synthesized by the reaction of 4‐hydroxyl‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy with 2‐bromo‐2‐methylpropionyl bromide. Stable free radical polymerization of styrene was then carried out using a conventional thermal initiator, dibenzoyl peroxide, along with Br‐TEMPO. The obtained polystyrene had an active bromine atom for ATRP at the ω‐end of the chain and was used as the macroinitiator for ATRP of methyl acrylate and ethyl acrylate to prepare block copolymers. The molecular weights of the resulting block copolymers at different monomer conversions shifted to higher molecular weights and increased with monomer conversion. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2468–2475, 2006     

Synthesis and characterization of sulfonated block copolymers by atom transfer radical polymerization

Well‐defined sulfonated polystyrene and block copolymers with n‐butyl acrylate (nBA) were synthesized by CuBr catalyzed living radical polymerization. Neopentyl p‐styrene sulfonate (NSS) was polymerized with ethyl‐2‐bromopropionate initiator and CuBr catalyst with N,N,N′,N′‐pentamethylethyleneamine to give poly(NSS) (PNSS) with a narrow molecular weight distribution (MWD < 1.12). PNSS was then acidified by thermolysis resulting in a polystyrene backbone with 100% sulfonic acid groups. Random copolymers of NSS and styrene with various composition ratios were also synthesized by copolymerization of NSS and styrene with different feed ratios (MWD < 1.11). Well defined block copolymers with nBA were synthesized by sequential polymerization of NSS from a poly(n‐butyl acrylate) (PnBA) precursor using CuBr catalyzed living radical polymerization (MWD < 1.29). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5991–5998, 2008     

Eutectic mixtures as a green alternative for efficient catalyst recycling in atom transfer radical polymerizations

A new solvent mixture, based on ethanol/reline (EM: eutectic mixture), was investigated for the supplemental activator and reducing agent atom transfer radical polymerization (SARA ATRP) of methyl acrylate (MA) near room temperature, for the first time, affording complete catalyst recovery and reuse. The kinetic results revealed that the polymerizations were controlled, with polymers having narrow molecular weight distributions (? < 1.2). The “living” character of the resultant PMA was confirmed by the synthesis of a well‐defined PMA‐b‐PBA block copolymer. Remarkably, it was demonstrated that the Cu(0)/CuBr₂/Me₆TREN (Me₆TREN: tris[2‐(dimethylamino)ethyl]amine) could be recovered from the final reaction mixture and reused for new successful SARA ATRP of MA, suggesting that the reported system could be very attractive from both the economic and environmental perspectives. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 371–381     

Block copolymer preparation by atom transfer radical polymerization under emulsion conditions using a nanoprecipitation technique

Living‐radical polymerization of acrylates were performed under emulsion atom transfer radical polymerization (ATRP) conditions using latexes prepared by a nanoprecipitation technique previously employed and optimized for the polymerization of styrene. A macroinitiator of poly(n‐butyl acrylate) prepared under bulk ATRP was dissolved in acetone and precipitated in an aqueous solution of Brij 98 to preform latex particles, which were then swollen with monomer and heated. Various monomers (i.e. n‐butyl acrylate, styrene, and tert‐butyl acrylate) were used to swell the particles to prepare homo‐ and block copolymers from the poly(n‐butyl acrylate) macroinitiator. Under these conditions latexes with a relatively good colloidal stability were obtained. Furthermore, amphiphilic block copolymers were prepared by hydrolysis of the tert‐butyl groups and the resulting block copolymers were characterized by dynamic light scattering (DLS) and transmission electron microscopy (TEM). The bulk morphologies of the polystyrene‐b‐poly(n‐butyl acrylate) and poly(n‐butyl acrylate)‐b‐poly(acrylic acid) copolymers were investigated by atomic force microscopy (AFM) and small angle X‐ray scattering (SAXS). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 625–635, 2008     

Growth of poly(methyl methacrylate) brushes on silicon surfaces by atom transfer radical polymerization

Poly(methyl methacrylate) (PMMA) brushes are grown by surface‐initiated atom transfer radical polymerization on silicon surfaces at various polymerization temperatures. Kinetic studies show that the layer thickness scales linearly with the degree of polymerization of the polymers under some conditions, indicating a constant graft density of the surface‐attached chains. At high temperatures, the layer growth is a controlled process only for short reaction times, and after a rapid increase, the film growth levels off, and a constant thickness is obtained. At lower reaction temperatures, polymers with a lower polydispersity are obtained, but at the expense of a much slower growth rate. Accordingly, intermediate temperatures yield the highest film thickness on experimentally feasible timescales. The reinitiation of these surface‐grafted PMMA chains at room temperature to either extend the chains or grow a chemically different polyglycidylmethacrylate block demonstrates the presence of active ends and the living nature of the surface‐grafted PMMA chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1758–1769, 2006     

A new tetradentate ligand for atom transfer radical polymerization

The properties of a ligand, including molecular structure and substituents, strongly affect the catalyst activity and control of the polymerization in atom transfer radical polymerization (ATRP). A new tetradentate ligand, N,N′‐bis(pyridin‐2‐ylmethyl‐3‐hexoxo‐3‐oxopropyl)ethane‐1,2‐diamine (BPED) was synthesized and examined as the ligand of copper halide for ATRP of styrene (St), methyl acrylate (MA), and methyl methacrylate (MMA), and compared with other analogous linear tetrdendate ligands. The BPED ligand was found to significantly promote the activation reaction: the CuBr/BPED complex reacted with the initiators so fast that a large amount of Cu(II)Br₂/BPED was produced and thus the polymerizations were slow for all the monomers. The reaction of CuCl/BPED with the initiator was also fast, but by reducing the catalyst concentration or adding CuCl₂, the activation reaction could be slowed to establish the equilibrium of ATRP for a well‐controlled living polymerization of MA. CuCl/BPED was found very active for the polymerization of MA. For example, 10 mol% of the catalyst relatively to the initiator was sufficient to mediate a living polymerization of MA. The CuCl/BPED, however, could not catalyze a living polymerization of MMA because the resulting CuCl₂/BPED could not deactivate the growing radicals. The effects of the ligand structures on the catalysis of ATRP are also discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3553–3562, 2004     

Controlled grafting of ethyl cellulose with azobenzene‐containing polymethacrylates via atom transfer radical polymerization

Graft copolymers of ethyl cellulose with azobenzene‐containing polymethacrylates were synthesized through atom transfer radical polymerization (ATRP). The residual hydroxyl groups on ethyl cellulose were first esterified with 2‐bromoisobutyryl bromide to yield 2‐bromoisobutyryloxy groups, which was then used to initiate the polymerization of 6‐[4‐(4‐methoxyphenylazo)phenoxy]hexyl methacrylate (MMAzo) in the presence of CuBr/N,N,N′,N″,N″‐pentamethylenetriamine (PMDETA) as catalyst and anisole as solvent. The graft copolymers were characterized by gel permeation chromatography (GPC) and ¹H‐NMR. The molecular weights of the graft copolymers increased relatively to the macroinitiator, and the polydispersities were narrow. The thermal and liquid crystalline property of the graft copolymers were investigated by differential scanning calorimeter (DSC) and polarizing optical microscope (POM). Photoresponsive property was studied under the irradiation of UV–vis light in THF solution. The graft copolymers have potential applications, including sensors and optical materials. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1653–1660, 2007     

Synthesis of semifluorinated block copolymers by atom transfer radical polymerization

Two sets of styrene‐based semifluorinated block copolymers, one with a perfluoroether pendant group and another with a perfluoroalkyl group, were synthesized by atom transfer radical polymerization. Microphase separation of the block copolymers was established by small‐angle X‐ray scattering and differential scanning calorimetry (DSC). DSC measurements also showed that the perfluoroether‐based polymer had a low glass‐transition temperature (?44 °C). Contact‐angle measurements indicated that the semifluorinated block copolymers had low surface energies (ca. 13 mJ/m²). These materials hold promise as low‐surface‐energy additives or surfactants for supercritical CO₂ applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 853–861, 2004     

Preparation of polyethylene block copolymers by a combination of postmetallocene catalysis of ethylene polymerization and atom transfer radical polymerization

The synthesis of block copolymers consisting of a polyethylene segment and either a poly(meth)acrylate or polystyrene segment was accomplished through the combination of postmetallocene-mediated ethylene polymerization and subsequent atom transfer radical polymerization. A vinyl-terminated polyethylene (number-average molecular weight = 1800, weight-average molecular weight/number-average molecular weight =1.70) was synthesized by the polymerization of ethylene with a phenoxyimine zirconium complex as a catalyst activated with methylalumoxane (MAO). This polyethylene was efficiently converted into an atom transfer radical polymerization macroinitiator by the addition of α-bromoisobutyric acid to the vinyl chain end, and the polyethylene macroinitiator was used for the atom transfer radical polymerization of n-butyl acrylate, methyl methacrylate, or styrene; this resulted in defined polyethylene-b-poly(n-butyl acrylate), polyethylene-b-poly(methyl methacrylate), and polyethylene-b-polystyrene block copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 496–504, 2004     

Living radical polymerization. II. Improved atom transfer radical polymerization of acrylamide in aqueous glycerol media with a novel pentamethyldiethylenetriamine‐based soluble copper(I) complex catalyst system

An improved atom transfer radical polymerization (ATRP) of acrylamide was achieved in a glycerol/water (1:1 v/v) medium with 2‐halopropionamide initiators, CuX (X = Cl or Br) as catalysts, pentamethyldiethylenetriamine (PMDETA) as a ligand, and CuX₂ (≥20 mol % CuX) and excess alkali halide (ca. 1 mol/dm³) as additives. The first‐order kinetic plots for the disappearance of the monomer at 130 °C were linear; this was a significant improvement over the results obtained earlier with the bipyridine ligand. However, even under such improved situations, about 7 mol % of the polymer chains were estimated to be formed dead. The polydispersity index was approximately 1.5. At a lower temperature (ca. 90 °C), a lower polydispersity index (1.24) was obtained for the bromide‐based initiating system. Chain‐extension experiments proved the living nature of the polymers. The presence of both extra halide ions and the monomer was necessary to take the CuX–PMDETA complex into solution. It was suggested that the soluble Cu(I) complex was formed with one PMDETA molecule acting as a monodentate ligand and with two halide ions and one acrylamide molecule occupying the other three coordination sites. Some support for the involvement of all three ligands (X^?, PMDETA, and acrylamide) in the complex formation was obtained from ultraviolet–visible spectroscopy studies. The better ATRP with the PMDETA ligand was attributed to the better stability and lesser hydrolysis of the 1:1 Cu⁺²/PMDETA complex with respect the corresponding bipyridine complex. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2483–2494, 2004     

Polymer–silicate nanocomposites produced by in situ atom transfer radical polymerization

Polymer–silicate nanocomposites were synthesized with atom transfer radical polymerization (ATRP). An ATRP initiator, consisting of a quaternary ammonium salt moiety and a 2‐bromo‐2‐methyl propionate moiety, was intercalated into the interlayer spacings of the layered silicate. Subsequent ATRP of styrene, methyl methacrylate, or n‐butyl acrylate with Cu(I)X/N,N‐bis(2‐pyridiylmethyl) octadecylamine, Cu(I)X/N,N,N′,N′,N″‐pentamethyldiethylenetriamine, or Cu(I)X/1,1,4,7,10,10‐hexamethyltriethylenetetramine (X = Br or Cl) catalysts with the initiator‐modified silicate afforded homopolymers with predictable molecular weights and low polydispersities, both characteristics of living radical polymerization. The polystyrene nanocomposites contained both intercalated and exfoliated silicate structures, whereas the poly(methyl methacrylate) nanocomposites were significantly exfoliated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 916–924, 2004     

Synthesis and characterization of well‐defined ABC‐type triblock copolymers via atom transfer radical polymerization and stable free‐radical polymerization

An asymmetric difunctional initiator 2‐phenyl‐2‐[(2,2,6,6 tetramethylpiperidino)oxy] ethyl 2‐bromo propanoate ( 1 ) was used for the synthesis of ABC‐type methyl methacrylate (MMA)‐tert‐butylacrylate (tBA)‐styrene (St) triblock copolymers via a combination of atom transfer radical polymerization (ATRP) and stable free‐radical polymerization (SFRP). The ATRP‐ATRP‐SFRP or SFRP‐ATRP‐ATRP route led to ABC‐type triblock copolymers with controlled molecular weight and moderate polydispersity (M_w/M_n < 1.35). The block copolymers were characterized by gel permeation chromatography and ¹H NMR. The retaining chain‐end functionality and the applying halide exchange afforded high blocking efficiency as well as maintained control over entire routes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2025–2032, 2002     

New antibacterial cationic surfactants prepared by atom transfer radical polymerization

Efficient antibacterial surfactants have been prepared by the quaternization of the amino groups of poly(ethylene‐co‐butylene)‐b‐poly[2‐(dimethylamino)ethylmethacrylate] (PEB‐b‐PDMAEMA) diblock copolymers by octyl bromide. The diblock copolymers have been synthesized by ATRP of 2‐(dimethylamino)ethylmethacrylate (DMAEMA) initiated by an activated bromide‐end‐capped poly(ethylene‐co‐butylene). In the presence of CuBr, 1,4,7,10,10‐hexamethyl‐triethylenetetramine (HMTETA), and toluene at 50 °C, the initiation is slow in comparison with propagation. This situation has been improved by the substitution of CuCl for CuBr, all the other conditions being the same. Finally, the addition of an excess of CuCl₂ (deactivator) to the CuCl/HMTETA catalyst is very beneficial in making the agreement between the theoretical and experimental number‐average molecular weights excellent. The antibacterial activity of PEB‐b‐PDMAEMA quaternized by octyl bromide has been assessed against bacteria and is comparable to the activity of a commonly used disinfectant, that is, benzalkonium chloride. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1214‐1224, 2006     

Synthesis of well‐defined macromonomers by the combination of atom transfer radical polymerization and a click reaction

This article presents a new strategy for synthesizing a series of well‐defined macromonomers. Bromine‐terminated polystyrene and poly(t‐butyl acrylate) with predetermined molecular weights and narrow distributions were prepared through the atom transfer radical polymerization of styrene and t‐butyl acrylate initiated with ethyl 2‐bromoisobutyrate. Then, azido‐terminated polymers were obtained through the bromine substitution reaction with sodium azide. Catalyzed by CuBr/N,N,N′,N″,N″‐pentamethyldiethylenetriamine, the azido end group reacted with propargyl methacrylate via a 1,3‐dipolar cycloaddition reaction, and ω‐methacryloyl‐functionalized macromonomers were thus obtained. The end‐group transformation yields were rather high, as characterized by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectra and ¹H NMR analysis. By this effective and facile approach, some novel macromonomers that otherwise are difficult to achieve, such as poly(ethylene oxide)‐block‐polystyrene, were easily prepared. Radical homopolymerizations of these macromonomers were performed, and a series of comb polymers were prepared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6103–6113, 2006     

Coupled atom transfer radical coupling and atom transfer radical polymerization approach for controlled grafting from poly(vinylidene fluoride) backbone

A new “grafting from” strategy for grafting of different monomers (methacrylates, acrylates, and acrylamide) on poly(vinylidene fluoride) (PVDF) backbone is designed using atom transfer radical coupling (ATRC) and atom transfer radical polymerization (ATRP). 4‐Hydroxy TEMPO moieties are anchored on PVDF backbone by ATRC followed by attachment of ATRP initiating sites chosen according to the reactivity of different monomers. High graft conversion is achieved and grafting of poly(methyl methacrylate) (PMMA) exhibits high degree of polymerization (DPn = 770) with a very low graft density (0.18 per hundred VDF units) which has been increased to 0.44 by regenerating the active catalyst with the addition of Cu(0). A significant impact on thermal and stress–strain property of graft copolymers on the graft density and graft length is noted. Higher tensile strain and toughness are observed for PVDF‐g‐PMMA produced from model initiator but graft copolymer from pure PVDF exhibits higher tensile strength and Young's modulus. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 995–1008     

Sequential synthesis of multiblock copolymers by atom transfer radical and cationic polymerization

ABCBA‐type pentablock copolymers of methyl methacrylate (MMA), styrene (S), and isobutylene (IB) were prepared by a three‐step synthesis, which included atom transfer radical polymerization (ATRP) and cationic polymerization: (1) poly(methyl methacrylate) (PMMA) with terminal chlorine atoms was prepared by ATRP initiated with an aromatic difunctional initiator bearing two trichloromethyl groups under CuCl/2,2′‐bipyridine catalysis; (2) PMMA with the same catalyst was used for ATRP of styrene, which produced a poly(S‐b‐MMA‐b‐S) triblock copolymer; and (3) IB was polymerized cationically in the presence of the aforementioned triblock copolymer and BCl₃, and this produced a poly(IB‐b‐S‐b‐MMA‐b‐S‐b‐IB) pentablock copolymer. The reaction temperature, varied from ?78 to ?25 °C, significantly affected the IB content in the product; the highest was obtained at ?25 °C. The formation of a pentablock copolymer with a narrow molecular weight distribution provided direct evidence of the presence of active chlorine at the ends of the poly(S‐b‐MMA‐b‐S) triblock copolymer, capable of the initiation of the cationic polymerization of IB in the presence of BCl₃. A differential scanning calorimetry trace of the pentablock copolymer (20.1 mol % IB) showed the glass‐transition temperatures of three segregated domains, that is, polyisobutylene (?87.4 °C), polystyrene (95.6 °C), and PMMA (103.7 °C) blocks. One glass‐transition temperature (104.5 °C) was observed for the aforementioned triblock copolymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6098–6108, 2004     

Synthesis of a well-defined glycopolymer by atom transfer radical polymerization

Controlled free radical polymerization of sugar-carrying methacrylate, 3-O-methacryloyl-1,2 : 5,6-di-O-isopropylidene-d-glucofuranose (MAIpGlc) was achieved by the atom transfer radical polymerization (ATRP) technique with an alkyl halide/copper-complex system in veratrole at 80°C. The time–conversion first-order plot was linear and the number-average molecular weight increased in direct proportion to the ratio of the monomer conversion to the initial initiator concentration, providing PMAIpGlc with a low polydispersity. The sequential addition of the two monomers styrene (S) and MAIpGlc afforded a block copolymer of the type PS-b-PMAIpGlc. The acidolysis of the homo- and block copolymers gave well-defined glucose-carrying water-soluble polymers PMAGlc and PS-b-PMAGlc, respectively. The amphiphilic PS-b-PMAGlc block copolymer exhibited a microdomain surface morphology with spherical PS domains in a PMAGlc matrix. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2473–2481, 1998     

Synthesis of halogen-free amino-functionalized polymethyl methacrylate by atom transfer radical polymerization (ATRP)

In order to obtain amino-terminated polymethyl methacrylate (PMMA-NH₂) free of halogen we used the atom transfer radical polymerization (ATRP) to polymerize methyl methacrylate (MMA) in presence of an initiator containing an alkyl bromide unit and a protected amine functional group. The use of CuBr / N,N,N′,N′′,N′′-pentamethyldiethylenetriamine (PMDETA) as co-catalyst system results in a polymer free of halogen due to hydrogen transfer from PMDETA to the growing polymer chain. However, side reactions occur affecting the typically “living” character of the ATRP. The measured molecular weights are consistently higher than the theoretical ones and the molecular weight distributions are relatively broad.     

Bulk atom transfer radical polymerization of allyl methacrylate

A detailed investigation of the polymerization of allyl methacrylate, a typical unsymmetrical divinyl compound containing two types of vinyl groups, methacryloyl and allyl, with quite different reactivities, was performed with atom transfer radical polymerization (ATRP). Homopolymerizations were carried out in bulk, with ethyl‐2‐bromoisobutyrate as the initiator and with copper halide (CuX, where X is Cl or Br) with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the catalyst system. Kinetic studies demonstrated that during the early stages of the polymerization, the ATRP process proceeded in a living manner with a low and constant radical concentration. However, as the reaction continued, the increased diffusion resistance restricted the mobility of the catalyst system and interrupted the equilibrium between the growing radicals and dormant species. The obtained poly(allyl methacrylate)s (PAMAs) were characterized with Fourier transform infrared, ¹H NMR, and size exclusion chromatography techniques. The dependence of both the gel point conversion and molecular characteristics of the PAMA prepolymers on different experimental parameters, such as the initiator concentration, polymerization temperature, and type of halide used as the catalyst, was analyzed. These real gel points were compared with the ones calculated according to Gordon's equation under the tentative assumption of equal reactivity for the two types of vinyl groups. Moreover, the microstructure of the prepolymers was the same as that exhibited by those homopolymers prepared by conventional free‐radical polymerization; the fraction of syndiotactic arrangements increased as the reaction temperature was lowered. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2395–2406, 2005