X‐ray spectromicroscopy with the scanning transmission X‐ray microscope at BESSY II

Using the scanning transmission X‐ray microscope at BESSY II, colloidal structures from a Chernozem soil have been studied with a spatial resolution around 60 nm and a spectral resolution of 1700 at the K‐absorption edge of carbon. Elemental mapping has been used to determine the distribution of organic matter within the colloidal structures. Spectra have been extracted from image stacks to obtain information about the chemical state. For the analysis of the latter, principal component analysis and cluster analysis have been applied. It was possible, for example, to discriminate clay particles against organic components.     

High‐accuracy X‐ray absorption spectra from mM solutions of nickel (II) complexes with multiple solutions using transmission XAS

A new approach is introduced for determining X‐ray absorption spectroscopy (XAS) spectra on absolute and relative scales using multiple solutions with different concentrations by the characterization and correction of experimental systematics. This hybrid technique is a development of standard X‐ray absorption fine structure (XAFS) along the lines of the high‐accuracy X‐ray extended range technique (XERT) but with applicability to solutions, dilute systems and cold cell environments. This methodology has been applied to determining absolute XAS of bis(N‐n‐propyl‐salicylaldiminato) nickel(II) and bis(N‐i‐propyl‐salicylaldiminato) nickel(II) complexes with square planar and tetrahedral structures in 15 mM and 1.5 mM dilute solutions. It is demonstrated that transmission XAS from dilute systems can provide excellent X‐ray absorption near‐edge structure (XANES) and XAFS spectra, and that transmission measurements can provide accurate measurement of subtle differences including coordination geometries. For the first time, (transmission) XAS of the isomers have been determined from low‐concentration solutions on an absolute scale with a 1–5% accuracy, and with relative precision of 0.1% to 0.2% in the active XANES and XAFS regions after inclusion of systematic corrections.     

Investigation of the multiplet features of SrTiO3 in X‐ray absorption spectra based on configuration interaction calculations

Synchrotron‐based L_2,3‐edge absorption spectra show strong sensitivities to the local electronic structure and chemical environment. However, detailed physical information cannot be extracted easily without computational aids. Here, using the experimental Ti L_2,3‐edges absorption spectrum of SrTiO₃ as a fingerprint and considering full multiplet effects, calculations yield different energy parameters characterizing local ground state properties. The peak splitting and intensity ratios of the L₃ and L₂ set of peaks are carefully analyzed quantitatively, giving rise to a small hybridization energy around 1.2 eV, and the different hybridization energy values reported in the literature are further addressed. Finally, absorption spectra with different linearly polarized photons under various tetragonal crystal fields are investigated, revealing a non‐linear orbital–lattice interaction, and a theoretical guidance for material engineering of SrTiO₃‐based thin films and heterostructures is offered. Detailed analysis of spectrum shifts with different tetragonal crystal fields suggests that the e_g crystal field splitting is a necessary parameter for a thorough analysis of the spectra, even though it is not relevant for the ground state properties.     

L‐series X‐ray emission spectra of 3d‐metal compounds with various excitation conditions

L‐series emissions of manganese, iron, and zinc oxides were studied using electron beam excitation and highly brilliant synchrotron radiation excitation. We showed that manganese and iron oxides show different Lβ/Lα intensity ratio because of their oxidation states and excitation electron voltages. On the other hand, we could not get any L‐series emissions from those bulk samples when excited by normal incident high‐energy monochromatic X‐rays, while samples of thin films and samples excited by grazing incident monochromatic X‐rays showed clear emissions. It is suggested that the difference of Lβ/Lα intensity ratio due to the oxidized states mainly concerns with the Coster–Kronig transition ratio of the samples, while self‐absorption effects should also deeply contribute the ratio, considering the experimental results. Copyright © 2016 John Wiley & Sons, Ltd.     

Improved charge transfer multiplet method to simulate M‐ and L‐edge X‐ray absorption spectra of metal‐centered excited states

Charge transfer multiplet (CTM) theory is a computationally undemanding and highly mature method for simulating the soft X‐ray spectra of first‐row transition metal complexes. However, CTM theory has seldom been applied to the simulation of excited‐state spectra. In this article, the CTM4XAS software package is extended to simulate M_2,3‐ and L_2,3‐edge spectra for the excited states of first‐row transition metals and also interpret CTM eigenfunctions in terms of Russell–Saunders term symbols. These new programs are used to reinterpret the recently reported excited‐state M_2,3‐edge difference spectra of photogenerated ferrocenium cations and to propose alternative assignments for the electronic state of these cations responsible for the spectroscopic features. These new programs were also used to model the L_2,3‐edge spectra of Fe^II compounds during nuclear relaxation following photoinduced spin crossover and to propose spectroscopic signatures for their vibrationally hot states.     

Measurement of angular distribution of soft X‐ray radiation from thin targets in the tabletop storage ring MIRRORCLE‐20SX

The only available tabletop electron storage rings are the machines from the MIRRORCLE series. The electrons are accelerated in a microtron and injected into the storage ring. During its circulation, each electron passes through a tiny target many times, emitting a photon beam. Both the spectrum and the angular distribution of the radiation depend on the material, the thickness and the shape of the target. In this paper measured angular distributions of the radiation from several different targets in the magnetic field of the 20 MeV storage ring MIRRORCLE‐20SX are presented. The detector comprises a 3 mm × 3 mm × 8.5 µm plastic scintillator (PS) coupled to a photomultiplier by a bundle of optical fibers. The output of the photomultiplier is digitized by an IF converter. This detector is sensitive mostly to soft X‐ray radiation, and its PS is moved by a mechanical system in a plane perpendicular to the radiation axis. The measured angular distributions for Mo and Sn targets contain an annulus which is attributed to transition radiation. The angular distributions for Al, carbon nanotube and diamond‐like carbon (DLC) targets show some suppression of the radiation along the magnetic field. This is the first evidence of observation of the angular distribution of synchrotron Cherenkov radiation, which represents Cherenkov radiation in a magnetic field. The power radiated from the DLC target is estimated.     

Grazing‐incidence X‐ray diffraction study of rubrene epitaxial thin films

The growth of organic semiconductors as thin films with good and controlled electrical performances is nowadays one of the main tasks in the field of organic semiconductor‐based electronic devices. In particular it is often required to grow highly crystalline and precisely oriented thin films. Here, thanks to grazing‐incidence X‐ray diffraction measurements carried out at the ELETTRA synchrotron facility, it is shown that rubrene thin films deposited by organic molecular beam epitaxy on the surface of tetracene single crystals have the structure of the known orthorhombic polymorph, with the (2 0 0) plane parallel to the substrate surface. Moreover, the exact epitaxial relationship between the film and the substrate crystalline structures is determined, demonstrating the presence of a unique in‐plane orientation of the overlayer.     

Effects of organic ligands on Pb absorption and speciation changes in Arabidopsis as determined by micro X‐ray fluorescence and X‐ray absorption near‐edge structure analysis

Pb can pass through the food chain via plants and threaten human health, which has attracted widespread attention. Changes in Pb speciation affect its bioavailability in soils and water. However, whether organic ligands can change the uptake and mobility of Pb in plants and increase or decrease Pb bioavailability remains uncertain. To reveal the roles of organic and inorganic Pb in Pb metabolism in plants, the localization and speciation changes of Pb in Arabidopsis thaliana plants grown in organic and inorganic Pb were characterized by synchrotron radiation micro X‐ray fluorescence and X‐ray absorption near‐edge structure, respectively. These results demonstrated that Arabidopsis absorbed more Pb from Pb(NO₃)₂ than Pb(CH₃COO)₂ at the same exposure concentration. A higher percentage of Pb‐citrate was found in Arabidopsis exposed to inorganic Pb solution, which suggested that Pb‐citrate was the main complex for root‐to‐shoot transportation in Arabidopsis exposed to inorganic Pb solutions. Pb complexed with the organic ligand CH₃COO^? significantly inhibited primary root growth and lateral root development, while, at the same time, Pb was blocked by root hairs, which represented another way to reduce Pb absorption and protect the plant from biotoxicity.     

Soft X‐ray absorption spectroscopy and resonant inelastic X‐ray scattering spectroscopy below 100 eV: probing first‐row transition‐metal M‐edges in chemical complexes

X‐ray absorption and scattering spectroscopies involving the 3d transition‐metal K‐ and L‐edges have a long history in studying inorganic and bioinorganic molecules. However, there have been very few studies using the M‐edges, which are below 100 eV. Synchrotron‐based X‐ray sources can have higher energy resolution at M‐edges. M‐edge X‐ray absorption spectroscopy (XAS) and resonant inelastic X‐ray scattering (RIXS) could therefore provide complementary information to K‐ and L‐edge spectroscopies. In this study, M_2,3‐edge XAS on several Co, Ni and Cu complexes are measured and their spectral information, such as chemical shifts and covalency effects, are analyzed and discussed. In addition, M_2,3‐edge RIXS on NiO, NiF₂ and two other covalent complexes have been performed and different d–d transition patterns have been observed. Although still preliminary, this work on 3d metal complexes demonstrates the potential to use M‐edge XAS and RIXS on more complicated 3d metal complexes in the future. The potential for using high‐sensitivity and high‐resolution superconducting tunnel junction X‐ray detectors below 100 eV is also illustrated and discussed.     

A setup for synchrotron‐radiation‐induced total reflection X‐ray fluorescence and X‐ray absorption near‐edge structure recently commissioned at BESSY II BAMline

An automatic sample changer chamber for total reflection X‐ray fluorescence (TXRF) and X‐ray absorption near‐edge structure (XANES) analysis in TXRF geometry was successfully set up at the BAMline at BESSY II. TXRF and TXRF‐XANES are valuable tools for elemental determination and speciation, especially where sample amounts are limited (<1 mg) and concentrations are low (ng ml^?1 to µg ml^?1). TXRF requires a well defined geometry regarding the reflecting surface of a sample carrier and the synchrotron beam. The newly installed chamber allows for reliable sample positioning, remote sample changing and evacuation of the fluorescence beam path. The chamber was successfully used showing accurate determination of elemental amounts in the certified reference material NIST water 1640. Low limits of detection of less than 100 fg absolute (10 pg ml^?1) for Ni were found. TXRF‐XANES on different Re species was applied. An unknown species of Re was found to be Re in the +7 oxidation state.     

Development of a two‐dimensional imaging system of X‐ray absorption fine structure

A two‐dimensional imaging system of X‐ray absorption fine structure (XAFS) has been developed at beamline BL‐4 of the Synchrotron Radiation Center of Ritsumeikan University. The system mainly consists of an ionization chamber for I₀ measurement, a sample stage, and a two‐dimensional complementary metal oxide semiconductor (CMOS) image sensor for measuring the transmitted X‐ray intensity. The X‐ray energy shift in the vertical direction, which originates from the vertical divergence of the X‐ray beam on the monochromator surface, is corrected by considering the geometrical configuration of the monochromator. This energy correction improves the energy resolution of the XAFS spectrum because each pixel in the CMOS detector has a very small vertical acceptance of ～0.5 µrad. A data analysis system has also been developed to automatically determine the energy of the absorption edge. This allows the chemical species to be mapped based on the XANES feature over a wide area of 4.8 mm (H) × 3.6 mm (V) with a resolution of 10 µm × 10 µm. The system has been applied to the chemical state mapping of the Mn species in a LiMn₂O₄ cathode. The heterogeneous distribution of the Mn oxidation state is demonstrated and is considered to relate to the slow delocalization of Li⁺‐defect sites in the spinel crystal structure. The two‐dimensional‐imaging XAFS system is expected to be a powerful tool for analyzing the spatial distributions of chemical species in many heterogeneous materials such as battery electrodes.     

An attempt to analyze the bark disease in Havea brasiliensis using X‐ray absorption near‐edge spectroscopy

The X‐ray absorption near‐edge spectroscopy (XANES) technique has been used to determine the chemical change of elements induced by bark diseases in Havea brasiliensis (rubber latex tree). The results show the good sensitivity of in situ XANES for characterizing the chemical structure of phosphorus, sulfur, potassium and calcium in healthy and diseased Havea brasiliensis. Important information for understanding the bark disease involved in the sulfur metabolism of plants was also obtained from XANES.     

Finite lifetime broadening of calculated X‐ray absorption spectra: possible artefacts close to the edge

X‐ray absorption spectra calculated within an effective one‐electron approach have to be broadened to account for the finite lifetime of the core hole. For methods based on Green's function this can be achieved either by adding a small imaginary part to the energy or by convoluting the spectra on the real axis with a Lorentzian. By analyzing the Fe K‐ and L_2,3‐edge spectra it is demonstrated that these procedures lead to identical results only for energies higher than a few core‐level widths above the absorption edge. For energies close to the edge, spurious spectral features may appear if too much weight is put on broadening via the imaginary energy component. Special care should be taken for dichroic spectra at edges which comprise several exchange‐split core levels, such as the L₃‐edge of 3d transition metals.     

X‐ray absorption and x‐ray fluorescence for the characterization of titanium oxide‐modified HPLC silicas

Titanium oxide grafted on to the surfaces of chromatographic silica was investigated by x‐ray fluorescence (XRF) and x‐ray absorption (XAS) spectroscopy and the latter used before and after the extensive use of this material as a support for reversed‐phase high‐performance liquid chromatography (RP‐HPLC). XRF indicated the formation of a complete 2:1 monolayer whereas XAS suggested the presence of more than one titanium oxide structure. These structures show some slight modification after immobilization of PMOS and use in HPLC. Copyright © 2005 John Wiley & Sons, Ltd.     

Local structure of NiAl compounds investigated by extended X‐ray absorption fine‐structure spectroscopy

The local structures of pure NiAl and Ti‐, Co‐doped NiAl compounds have been obtained utilizing extended X‐ray absorption fine‐structure (EXAFS) spectroscopy. The results provide experimental evidence that Ni antisite defects exist in the Ni‐rich NiAl compounds. The site preference of Ti and Co has been confirmed. Ti occupies the Al sublattice, while Co occupies the Ni sublattice. The structure parameters obtained by EXAFS were consistent with the X‐ray diffraction results. Owing to the precipitation of α‐Cr, the local structure of NiAl‐Cr has not been obtained, making the site preference of Cr unclear.     

X‐ray‐excited optical luminescence and X‐ray absorption fine‐structures studies of CdWO4 scintillator

X‐ray‐excited optical luminescence (XEOL) emission and excitation spectra as well as the EXAFS signal of CdWO₄ were measured in the energy region of the Cd and W absorption edges. From EXAFS refinement, structural parameters such as number of atoms, distance from the absorbing atom and width of coordination shells in the W neighborhood were determined. The role of W–O interactions on the intrinsic luminescence of CdWO₄ is discussed. The efficiencies of conversion, transfer and emission processes involved in the scintillation mechanism showed to be high when self‐trapped excitons are formed locally by direct excitation of W ions. Annihilation of these excitons provides the characteristic scintillation of CdWO₄, a broad band emission with maximum at 500 nm. The presence of two energetically different O positions in the lattice gives rise to the composite structure of the luminescence band, and no influence of extrinsic defects was noticed. A mismatch between the X‐ray absorption coefficient and the zero‐order luminescence curves corroborates that the direct excitation of Cd ions induces secondary electronic excitations not very effective in transferring energy to the luminescent group, WO₆.     

In situ synchrotron X‐ray diffraction analysis of deformation behaviour in Ti–Ni‐based thin films

Deformation mechanisms of as‐deposited and post‐annealed Ti_50.2Ni_49.6, Ti_50.3Ni_46.2Cu_3.5 and Ti_48.5Ni_40.8Cu_7.5 thin films were investigated using the in situ synchrotron X‐ray diffraction technique. Results showed that initial crystalline phases determined the deformation mechanisms of all the films during tensile loading. For the films dominated by monoclinic martensites (B19′), tensile stress induced the detwinning of 〈011〉 type‐II twins and resulted in the preferred orientations of (002)_B19′ parallel to the loading direction (∥ LD) and (020)_B19′ perpendicular to the LD (⊥ LD). For the films dominated by austenite (B2), the austenite directly transformed into martensitic variants (B19′) with preferred orientations of (002)_B19′ ∥ LD and (020)_B19′ ⊥ LD. For the Ti_50.3Ni_46.2Cu_3.5 and Ti_48.1Ni_40.8Cu_7.5 films, martensitic transformation temperatures decreased apparently after post‐annealing because of the large thermal stress generated in the films due to the large differences in thermal expansion coefficients between the film and substrate.     

Pressure study of monoclinic ReO2 up to 1.2 GPa using X‐ray absorption spectroscopy and X‐ray diffraction

The crystal and local atomic structure of monoclinic ReO₂ (α‐ReO₂) under hydrostatic pressure up to 1.2 GPa was investigated for the first time using both X‐ray absorption spectroscopy and high‐resolution synchrotron X‐ray powder diffraction and a home‐built B₄C anvil pressure cell developed for this purpose. Extended X‐ray absorption fine‐structure (EXAFS) data analysis at pressures from ambient up to 1.2 GPa indicates that there are two distinct Re—Re distances and a distorted ReO₆ octahedron in the α‐ReO₂ structure. X‐ray diffraction analysis at ambient pressure revealed an unambiguous solution for the crystal structure of the α‐phase, demonstrating a modulation of the Re—Re distances. The relatively small portion of the diffraction pattern accessed in the pressure‐dependent measurements does not allow for a detailed study of the crystal structure of α‐ReO₂ under pressure. Nonetheless, a shift and reduction in the (011) Bragg peak intensity between 0.4 and 1.2 GPa is observed, with correlation to a decrease in Re—Re distance modulation, as confirmed by EXAFS analysis in the same pressure range. This behavior reveals that α‐ReO₂ is a possible inner pressure gauge for future experiments up to 1.2 GPa.     

On the correlation between the X‐ray absorption chemical shift and the formal valence state in mixed‐valence manganites

Here the correlation between the chemical shift in X‐ray absorption spectroscopy, the geometrical structure and the formal valence state of the Mn atom in mixed‐valence manganites are discussed. It is shown that this empirical correlation can be reliably used to determine the formal valence of Mn, using either X‐ray absorption spectroscopy or resonant X‐ray scattering techniques. The difficulties in obtaining a reliable comparison between experimental XANES spectra and theoretical simulations on an absolute energy scale are revealed. It is concluded that the contributions from the electronic occupation and the local structure to the XANES spectra cannot be separated either experimentally or theoretically. In this way the geometrical and electronic structure of the Mn atom in mixed‐valence manganites cannot be described as a bimodal distribution of the formal integer Mn³⁺ and Mn⁴⁺ valence states corresponding to the undoped references.