BEPCⅡ直线加速器的双脉冲加速研究

 为了将BEPCⅡ直线加速器的正电子注入速率提高到单脉冲运行时的两倍左右, 提出了双脉冲产生和加速的方案。对BEPCⅡ直线加速器双脉冲加速的束流动力学进行了模拟, 首次给出了双脉冲的模拟方法。此外, 还在BEPCⅡ直线加速器上进行了双脉冲加速的初步实验研究, 为以后BEPCⅡ直线加速器的进一步改造提供了参考。     

Progress of the Injector Linac Upgrade for the BEPCⅡ Project

BEPCⅡ—an upgrade project of Beijing Electron Positron Collider (BEPC) is a factory type of e+e- collider. It requires its injector linac to have a higher beam energy (1.89 GeV) for on-energy injection and a higher beam current (40 mA e+ beam) for a higher injection rate ( 50 mA/min). The low beam emittance (1.6π mm·mrad for e+ beam, and 0.2πmm·mrad for 300 mA e- beam) and the low beam energy spread (±0.5%) are also required to meet the storage ring acceptance. Thus the original BEPC injector linac must be upgraded to have a new electron gun with its complete tuning system, a new positron source with a flux concentrator, a new RF power system with its phasing loops and a new beam tuning system with orbit correction and optics tuning devices. These new components have been designed, fabricated, tested and will be installed in their final positions in this spring and summer, which are described in this paper.     

北京正负电子对撞机束团拉伸效应研究

本文叙述了在北京正负电子对撞机(BEPC)上,用条纹相机和频谱分析方法对束团拉伸效应的研究.由测量结果归纳出BEPC束团拉伸效应的标度规律,这一规律与理论分析有相当好的一致关系.     

Design and simulation of the wire scanner for the injector linac of BEPC Ⅱ

BEPC Ⅱ,the upgrade project of Beijing Electron Positron Collider (BEPC),is an accelerator with large beam current and high luminosity,so an efficient and stable injector is required.Several beam diagnostic and monitoring instruments are used.A new diagnostic instrument--wire scanner,has been designed and will be used to nleasure the profile of the linac beam of BEPC Ⅱ.This paper describes the prototype of this system and the cause of heat generating of the wire.Some simulation results of the heat and force by using finite element method software-ANSYS(R),2) are presented and discussed.     

Studies on electron cloud instability in BEPCⅡ

Electron Cloud Instability has been studied in the operation of BEPC. The BEPCⅡ began the commissioning in November 2006 and the positron beam current has reached 500 mA. Because of such a high beam current, some instabilities such as ECI, bunch lengthening et al, have appeared during the operation. The experimental investigation on ECI during the commissioning of BEPCⅡ will be reported in this paper.     

BEPC II直线加速器数字BPM前端调理电路的研制

针对北京正负电子对撞机改造工程（BEPC II）直线加速器束流位置测量电子学系统故障率上升这一现状,结合BEPC II直线加速器束流参数以及BPM电子学ADC芯片带通采样的需求,设计了隔离度高、幅相一致性好的数字BPM射频前端电子学模块。数字BPM电子学系统采用MicroTCA 4.0系统架构,以FPGA作为主控制器,基于EDA软件开发设计。重点介绍了射频前端电子学模块中射频功率放大器、数字可调衰减器、带通滤波器等设计和实验室及在线测试结果。BEPC II对撞模式下,使用正电子束流,完成电子学系统在线测试,x方向位置测量精度约为38.46 μm,y方向位置测量精度约为26.16 μm,其测量精度和系统稳定性优于商用模拟BPM电子学模块,能够满足BEPC II直线加速器束流位置测量需求。     

离子俘获的线性理论及其应用

从线性理论出发,研究了电子束团在储存环里均匀分布和束团串两种情况下离子俘获的条件;在离子系统里引入Twiss参量,推导出电子束团串俘获离子的阈值流强的公式;并以此讨论北京正负电子对撞机(BEPC)在同步辐射专用运行时观察到的电子束流现象,提出采用束团串运行来克服BEPC中的束流寿命下降.     

束流逐圈位置测量在BEPC储存环上的初步应用

介绍了利用合肥同步辐射光源(HLS)的逐束团位置测量系统在北京正负电子对撞机(BEPC)上进行的逐圈位置测量实验. 在不同条件下对束流进行逐圈位置测量, 得到束流的相运动图像并观测了阻尼效应. 利用基频数值分析(NAFF)方法对逐圈位置数据分析得到高精度的束流频谱, 可以由此研究各种效应引起的工作点漂移. 实验中观测到特定工作点下由色品校正六极子引起的束流共振现象, 并对此作了合理解释.     

BEPCⅡ Control System

The BEPCⅡ project is for upgrading the Beijing Electron Positron Collider to reach a higher luminosity.BEPCⅡ is designed as micro-β plus multi-bunches with double rings and has adopted cryogenic superconducting technology. The BEPCⅡ control system is a distributed system based on EPICS. In the past few years, we went through the design stage, R&D stage, development stage and the system will be installated. The BEPCⅡ machine commissioning with beam will start in October 2006. This paper describes the BEPCⅡ~control system and the progress of its development.     

BEPC中的电子云不稳定性研究

多束团正电子储存环中可能发生电子云不稳定性(ECI). 自1996年起, 在北京正负电子对撞机(BEPC)上开展了与这种束流不稳定性相关的系列研究. 文章扼要介绍在BEPC上进行的电子云不稳定性研究, 包括实验观测和模拟计算, 并讨论可能的抑制措施.     

BEPC储存环束流振荡频率测量

在加速器的运行和机器研究过程中,需要经常对束流振荡频率进行测量.BEPC储存环束流振荡频率测量系统包括一台频谱仪,两个条形电极装置,两个电压放大器和一个束流振荡检测器.本文介绍了经过改进的BEPC储存环束流振荡频率测量系统.     

同步加速器中束流能量的修正

叙述了同步加速器中束流能量测量和修正的原理,推导出关于闭合轨道畸变和校正二极子强度的束流能量的修正公式,介绍了这些公式在北京正负电子对撞机（BEPC）上的应用,并对其结果进行了讨论．     

BEPCⅡ横向束流反馈系统样机在BEPC上的实验

为了抑制BEPCⅡ产生的耦合束团不稳定性, 提高储存环中的流强, 研制了一套逐束团横向束流反馈系统的样机并在BEPC上做了实验, 得到了理想的结果. 当束团不稳定时, 频谱仪上可以观察到横向边带, 此时将反馈系统闭环工作于阻尼状态时, 横向边带立即消失. 本文介绍了样机系统的组成、各部分的功能和实验结果.     

The Experiments of Transverse Feedback System on the BEPC

In order to cure the transverse coupled-bunch instabilities of BEPCⅡ and improve the beam current of the rings, a prototype of transverse bunch-by-bunch feedback system was studied and made. The experiment of this prototype on the BEPC storage ring shows that this system can work well. The beam instabilities can be successfully suppressed when the feedback loop is closed. This paper describes the prototype of the transverse feedback system and the preliminary test results.     

BEPCⅡ逐束团测量系统的研制及应用研究

基于北京正负电子对撞机二期工程储存环,研制了一套逐束团束流测量系统。系统包括模拟前端、数据采集处理控制和显示软件三个部分。储存环束流位置探头的四路信号作为逐束团测量系统的输入,该系统宽带模拟前端完成信号幅度相位的调理,并保证束团间无干扰;四路500 MHz模数转换器对信号采样实现逐束团测量;基于现场可编程门阵列的数字信号处理逻辑计算得到每个束团的位置。系统在线实时束流位置测量分辨率优于4.5μm,同时该测量系统可实现实时逐束团振荡幅度和工作点的测量。系统还拥有存储大容量逐束团原始数据的功能,为日常的机器研究提供了有力的测量手段。     

闪烁体瓦片/光纤量能器辐照损伤的进一步研究

研究了由不同闪烁体瓦片/光纤材料组成,或材料相同但构造不同的量能器模型的辐照损伤.用北京正负电子对撞机(BEPC)的电子试验束(1.1或1.3GeV)辐照了十个量能器模型.通过测量在不同累积剂量和在量能器内的不同位置上的光输出,对辐照损伤作出定量分析.还研究了损伤后的恢复及损伤与环境气体的关系.通过数据拟合发展了辐照损伤对剂量及对深度断面的校正方法.     

BEPCⅡ:construction and commissioning

This is a status report of the project on befalf of the BEPC Ⅱ team.BEPC Ⅱ is a major upgrade radiation(SR)source with its outer ring,or SR ring.As a collider,BEPC Ⅱ operates in the beam energy region of 1-2.3 GeV with design luminosity of 1×1033 cm-2s-1 at 1.89 GeV.As a light source.the SR ring operates at 2.5 GeV and 250 mA.Construction of the project started in the beginning of 2004.Installation of the storage ring components was completed in October 2007.Commissioning is in progress.There are still many issues for further studies before reach to 3×1032 cm-2s-1.     

Construction of the Phasing System for BEPCⅡ Linac

In order to get high beam quality, a RF distribution system is required, with minimal phase drifts and errors in the BEPCⅡ linac. The additional installation of phase reference cables and monitoring equipments and stable RF distribution for BEPC linac are finished. The master oscillator is chosen to offer RF signal with low phase noise and a stable phase distribution system is built to deliver RF signal to each klystron. A phase and amplitude detector is constructed to measure the phase precisely and an IΦA unit is used for a phase shifter. Control software based on EPICS is used to connect all the units of the system, and a phasing method based on BPM is adopted to optimize the phase of each klystron. Now the phasing system is installed and tested in the klystron gallery of the BEPCⅡ linac.     

BEPCⅡ零模束流反馈系统研制

 为了抑制BEPCⅡ多束团(93团)、大流强（910 mA）时的纵向振荡（零模）,引入了BEPCⅡ零模束流反馈系统。该系统首次应用于BEPCⅡ储存环上,它包括了束流信号采集、滤波、下变频、鉴相、移相等几个部分。使用该系统后,束流的纵向边带被抑制度大于10 dB,这表明,系统能够抑制束流的纵向振荡。     

4W1磁铁电源控制系统的改造

在北京正负电子对撞机(BEPC)中用于同步辐射~X~光研究的插入件4W1磁铁由主线圈绕组和补偿线圈绕组组成,由两台高精度直流电源(主电源和辅助电源)供电. 2004~年11月, BEPC开机使用的两台主电源和辅助电源是重新设计制造的,采用新的控制接口PSI和控制器PSC进行控制. 这套系统是在~BEPCⅡ磁铁电源控制样机PSC/PSI完成的基础上仅用1个月的时间完成的. 在运行初期经过多次调试和修改后, 安全无故障运行历时4个月,为同步辐射提供两条X光束线,保证了用户顺利地进行实验. 它是第一个投入运行的BEPCⅡ储存环控制系统的一个新系统. 介绍了基于EPICS平台开发的4W1磁铁电源新的控制系统和4W1磁铁 升降流的特点以及控制升降流应用程序的研制.