互补三刺激值光度法用于Ce、Y-CPAmA体系动力学特征研究和钪、钇、铈的同时测定

用互补三刺激值光度法处理Ce、Y-CPAmA体系,揭示配合物组成和相关的动力学特征,研究了影响α型向β型配合物转化的因素。在选定的条件下,以试剂为空白,同时测定了钪、钇和铈。     

高真空强静电场下半熔融态处理压电聚合物--PA11/PVDF共混物晶体结构和显微形态研究

使用ＷＡＸＤ和ＳＥＭ研究了高真空强静电场下半熔融态处理不同共混比例（ＰＡ１１／ＰＶＤＦ＝０／１００、２０／８０、４０／６０、６０／８０、８０／２０、１００／０）的压电聚合的ＰＡ１１／ＰＶＤＦ共混物压片的晶体结构和形态。ＷＡＸＤ分析表明,纯ＰＶＤＦ经不同强度静电场半熔融态处理后晶体结构并没有发生改变,均为β型ＰＶＤＦ;而纯ＰＡ１１经不同强度静电场半熔融态处理后晶体结构发生了改变,随电场强度的增加,部分ＰＡ１１由α型向δ′型转变。ＰＡ１１／ＰＶＤＦ共混物经不同强度静电场半熔融态处理后,当ＰＡ１１含量较小时,其结晶相为由β型ＰＶＤＦ和α型ＰＡ１１组成的混合相,并没有新相产生;而当ＰＡ１１含量较大时,共混物中的部分ＰＡ１１同样由α型向δ′型ＰＡ１１组成的混合相。ＳＥＭ观察表明,在无电场时,纯ＰＡ１１和纯ＰＶＤＦ呈混乱状     

细旦尼龙6纤维加工过程中的晶型转化行为

通过引入富镧稀土化合物等添加剂,成功实现了细旦尼龙6纤维的熔融纺丝．考察了在纺丝卷绕成型以及牵伸过程中尼龙6纤维的晶型变化．借助XRD和FT－IR等研究手段,发现尼龙6在纺丝过程中可以生成亚稳态的B晶型晶体．这种β晶型经过沸水处理后很容易转化为α晶型,而γ晶型尼龙6经沸水处理后不发生相转变．因此可以通过沸水热处理的方法区分尼龙6的β和γ晶型．在纤维的卷绕过程中,当熔体拉伸倍数较高时,尼龙6可能产生β晶型;当熔体拉伸倍数较低时,则以γ晶型为主．在纤维的牵伸过程中,γ晶型经过β晶型中间态向α晶型相转变．上述结果对于指导改进细旦尼龙6纤维的加工工艺以及提高产品性能有指导意义．     

氮酮对鼠角质层角蛋白作用的光谱证据

应用13CNMR和ATR-FTIR为测试手段,探讨角蛋白的分子运动自由度与堆积结构,以及氮酮对鼠角质层角蛋白的作用.经氮酮处理后,角蛋白主侧链碳的自旋晶格弛豫时间t1从7.9,8.2和2.1s分别减小到5.4,3.6和1.6s,表明氮酮作用加快了角蛋白所有碳的运动,获得了氮酮对鼠角质层角蛋白作用的确凿证据.同时,ATR-FTIR结果显示,经氮酮处理后,角蛋白的酰胺吸收峰带的峰位从1544.7cm^-1向低波数位移到1541.4cm^-1.结果表明氮酮可使部分角蛋白从α-螺旋型结构向β-折叠型结构和无规则卷曲型结构转变,导致角蛋白的堆积结构疏松,增大了角蛋白碳运动的自由度     

国内离子交换法处理氰化镉废水的现状及改进意见

本文对国内现行离子交换法处理氰化镀镉废水的工艺进行了探讨，提出了用络合理论将阴树脂由Ｃｌ－１型转变成ＣｄＣｌ４２－型后交换，便可提高对水中游离氰（ＣＮ－）的吸附能力，并能使氰、镉都得到回收利用。     

不同初始结构间规聚丙烯纤维熔融过程中的结晶转变行为

通过熔融纺丝及随后的热处理制备了具有不同初始结构的间规聚丙烯纤维(sPP).采用差示扫描量热仪(DSC)和变温广角X-射线衍射仪详细研究了sPP纤维在升温过程中的结构转变和熔融行为.结果表明,不同初始结构sPP纤维的晶型不同,卷绕纤维和退火处理纤维以Ⅰ型和Ⅱ型晶型为主,牵伸纤维介晶相占优;升高温度导致Ⅰ型和Ⅱ型两种晶型直接熔融,没有出现Ⅱ型向Ⅰ型的晶型转变;初始结构为介晶相的纤维在升温过程中部分介晶相直接转变为Ⅱ型晶型,还有一部分介晶相直接熔融,并在随后的升温过程中,形成Ⅰ型晶型.sPP纤维的多重熔融行为与其初始结构和纤维制备条件密切相关.     

晶种法高效合成低硅铝比LSX型分子筛

分别以工业级的偏铝酸钠和水玻璃为铝源和硅源,氢氧化钠为主要碱源,氢氧化钾为辅助碱源,采用LSX晶种法制备了LSX型分子筛。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线荧光(XRF)、傅里叶变换红外光谱(FTIR)和N2吸附-脱附等表征方式考察了有无晶种、钾钠物质的量之比、晶化条件对合成LSX型分子筛的影响。结果表明,加入LSX晶种不仅能显著缩短晶化时间,提高分子筛的结晶度,还可有效抑制方钠石和A型杂晶的伴生;钾钠比过高或过低均会造成A型或方钠石型杂晶的伴生;直接进行高温晶化会导致亚稳态的LSX型分子筛向热力学稳定相转变;延长老化时间或高温晶化处理降低了产物中的硅铝比;样品的比表面积和N2吸附量随老化时间的延长和高温晶化处理而逐渐下降。     

液晶显示材料

介绍了液晶的结构类型,液晶分子的光电效应,实现液晶显示的偏振片透光原理,包括扭曲向列型（TN）、超扭曲向列型（STN）、薄膜晶体管型（TFT）液晶显示的异同,可用于液晶显示的有机材料,以及液晶显示材料的产业现状及发展趋势。     

分散体系中任意形状的胶粒模型与相互作用能——Ⅲ. 园柱体型颗粒

在分散体系的研究中,也经常遇到园柱体型胶粒,例如蛋白质分子,海泡石和凸凹棒石粘土颗粒,它们都能用带电的园柱体型采近似处理。这种类型的颗粒以往研究不多,其原因大约有二,一是处理这类颗粒时,数学上的困难很大;二是这类颗粒之间的相互作用,和它们之间的取向有关。Sparnaay首先用Derjaguin法得出园柱体型颗粒处于平行和垂直位置时,相互排斥能的近似表达式。Brenner和McQuarrie(BM)对颗粒外的电位分布采     

聚苯乙烯阳离子交换树脂碳化产物的X射线衍射分析

用X射线衍射法分析了聚苯乙烯阳离子交换树脂碳化产物石墨化度和微观结构参数，结果表明聚苯乙烯阳离子交换树脂在1000℃以下碳化处理的样品，石墨化程度都很低，属于在中低温条件下较难石墨化处理的树脂样品；H型树脂碳化产物的晶面层有着碳化处理温度升高而依次减小，并且（002）晶面层间距减小速度快于（100）晶面；H型树脂在低温碳化处理条件下，主要是在二维平面结构上演变成石墨微晶，只有碳化处理温度较高时，平面结构的石墨微晶才相互调整，形成纵向平行有序的微晶体；树脂掺杂金属离子后，有利于树脂在碳化过程中形成的石墨微晶层片纵向有序排列；掺杂不同金属离子的树脂碳化样品，在结构参数方面都明显不同于未掺杂的H型树脂碳化样品。     

Film formation of yogurt under confined condition

The yogurt film confined within a nanogap was investigated by the thin film interferometry between two solid surfaces. Significantly thick film was found even under a low speed, which indicated yogurt might have excellent lubrication performance. The film thickness was much higher than the prediction of elastohydrodynamic lubrication theory. Experiment results indicated that the thick confined film of yogurt can be induced by the adhesion of organic material, which can sustain high pressure without being extruded under low speed. The effect of the rolling speed on film thickness shows that the lubrication under a high rolling speed tends to be the elastohydrodynamic lubrication. Copyright © 2011 John Wiley & Sons, Ltd.     

Humidity responsive asymmetric free-standing multilayered film

A humido-responsive free-standing film has been created using layer-by-layer assembly technique. Polyethylenimine (PEI) at high pH was assembled with poly(acrylic acid) (PAA) at low pH on a Teflon substrate to yield a micro-nanostructured surface that can be made superhydrophobic after being coated with a low surface energy compound. The resulting asymmetric free-standing film with one surface being superhydrophobic while the other is hydrophilic after detachment from the substrate can undergo reversible bending/unbending shape transitions when the environmental humidity is changed. The bending/unbending movement of the free-standing film can be ascribed to the different responses of these two surfaces to humidity.     

Miscibility Studies on cross-linked EVA/LLDPE Blends by TMDSC

Cross-linked polymers have particular rheological responses during reprocessing, e. g. if the material is recycled, special processing conditions are required. Other virgin polymers can be used as a blending component to enhance rheological properties. Bi-layer film of EVA/LLDPE was produced on a blown film line and cross-linked by high-energy radiation. This film was ‘agglomerated’ then reprocessed in a twin-screw extruder with virgin LLDPE and blown into film. The miscibility of the blend components was then studied using a TA Instruments temperature modulated differential scanning calorimeter (TMDSC). It was found that the cross-linked EVA/LLDPE scrap and the LLDPE have a slight miscibility in the liquid state. A bigger portion of LLDPE was miscible (dissolved) in EVA in low LLDPE blends. A positive deviation in the heat capacity of the LLDPE component compared to the additivity rule indicated melting to be more reversible in the first heating cycle. This initial miscibility was attributed to being induced by high shear during processing. A smaller positive deviation also occurred in the second heating cycle. This was attributed to intrinsic miscibility. This revised version was published online in August 2006 with corrections to the Cover Date.     

聚乙烯薄膜中微量羰基的紫外分析法——薄膜中苯腙的生成及其影响因素

<正> 将分析有机物中2,4-二硝基苯脘的紫外光谱法(简称DNPH-UV法)用于固体高分子材料的羰基检测,在70年代才有报道.Kato利用DNPH-UV法和红外光谱法(IR法)跟踪聚乙烯薄膜在光氧化中羰基的生成数据,两者的检测灵敏度几乎相同,而Johnson等用前一方法曾检出聚乙烯薄膜中有极少量羰基存在,但缺少相应的IR数据,其灵敏度难以判断.此外,在应用DNPH-UV法时,所规定的反应条件也不同,对影响反应的各种因素,特别是对检测灵敏度的影响,仍缺乏资料.因此本文以聚乙烯薄膜为对象,对样品的氧化程度、厚度及其反应条件和反应液的组分等进行了研究.     

Reversible wettability of a chemical vapor deposition prepared ZnO film between superhydrophobicity and superhydrophilicity

A superhydrophobic ZnO thin film was fabricated by the Au-catalyzed chemical vapor deposition method. The surface of the film exhibits hierarchical structure with nanostructures on sub-microstructures. The water contact angle (CA) was 164.3 degrees, turning into a superhydrophilic one (CA < 5 degrees) after UV illumination, which can be recovered through being placed in the dark or being heated. The film was attached tightly to the substrate, showing good stability and durability. The surface structures were characterized by scanning electron microscopy and atomic force microscopy.     

电响应聚合物薄膜的表面图案化

由于图案化的功能表面在制备微流体器件和生物芯片等方面具有巨大应用潜力而备受关注,表面图案化的方法很多，如微接触印刷、光刻蚀和电子束刻蚀等等,聚2-丙烯酰胺基-2-甲基丙基磺酸（PAMPS）是一种电响应聚合物，在电场的作用下其体积能发生大幅度的变化，我们曾经报道通过带偏压的原子力针尖对PAMPS薄膜的微观浸润性进行调控,本文采用预先结构化的电极对薄膜施加电场，实现了其表面性质的图案化控制，对制备新型聚合物微器件具有重要意义。     

Quantitative assessment of the enzymatic degradation of amorphous cellulose by using a quartz crystal microbalance with dissipation monitoring

The systematic evaluation of the degradation of an amorphous cellulose film by a monocomponent endoglucanase (EG I) by using a quartz crystal microbalance with dissipation monitoring (QCM-D) identified several important aspects relevant to the study the kinetics of cellulose degradation by enzymes. It was demonstrated that, to properly evaluate the mechanism of action, steady state conditions in the experimental set up need to be reached. Rinsing or diluting the enzyme, as well as concentration of the enzyme, can have a pronounced effect on the hydrolysis. Quantification of the actual hydrolysis was carried out by measuring the film thickness reduction by atomic force microscopy after the enzymatic treatment. The values correlated well with the frequency data obtained by QCM-D measurement for corresponding films. This demonstrated that the evaluation of hydrolysis by QCM-D can be done quantitatively. Tuning of the initial thickness of films enabled variation of the volume of substrate available for hydrolysis which was then utilized in establishing a correlation between substrate volume and hydrolytic activity of EG I as measured by QCM-D. It was shown that, although the amount of substrate affects the absolute rate of hydrolysis, the relative rate of hydrolysis does not depend on the initial amount of substrate in steady state system. With this experimental setup it was also possible to demonstrate the impact of concentration on crowding of enzyme and subsequent hydrolysis efficiency. This effort also shows the action of EG I on a fully amorphous substrate as observed by QCM-D. The enzyme was shown to work uniformly within the whole volume of swollen film, however being unable to fully degrade the amorphous film.     

2,2′-联吡啶荧光探针快速检测纳米TiO2薄膜的光催化活性

紫外光照射浸有纳米TiO2薄膜的溶液,能够产生羟自由基,其中羟自由基又能将荧光微弱的2,2′-联吡啶羟基化,其反应体系的荧光增强.利用2,2′-联吡啶作为荧光探针,通过检测其羟基化产物的生成速率来迅速、准确地评价纳米TiO2薄膜的光催化活性.通过与传统的染料法对比,荧光探针法极大地缩短了检测时间,从180 min减少到8 min,得出2,2′-联吡啶荧光探针法评价纳米TiO2薄膜光催化活性具有可行性.     

Au@Pt纳米粒子单层膜对甲醇氧化的电催化性能及SERS研究

通过种子生长法合成Au@Pt核壳结构纳米粒子,采用两相成膜法制备单层粒子膜,并转移获得Au@Pt核壳纳米粒子单层膜电极,该电极表面纳米粒子分布均匀,具有较大的比表面,对甲醇的氧化具有较好的电催化活性.研究表明,利用内核Au的长程电磁场增强效应,该单层膜表现出均匀且优良的表面增强拉曼散射(SERS)活性,适合作为基底在分子水平上研究表面的吸附和反应.获得了Au@Pt核壳纳米粒子单层膜表面甲醇电催化氧化过程的SERS光谱,为深入分析表面反应机理提供了实验依据.     

Supramolecular Materials Comprising Nucleic Acid Biopolymers

We have generated a supramolecular self-assembling film by exchanging the counter-ions of the phosphate moieties in nucleic acid with those of cationic amphiphiles as didodecyldimethylammonium bromide (or DDAB). SAXS and WAXS data for all film samples showed similar harmonic peaks suggesting a lamellar multilayer structure with layers of nucleic acids being separated by lipid bilayers of DDAB. AFM height images also showed that double stranded nucleic acid film can form the step or plateau type of structure and shorter nucleic acid film showed shorter step feature. Moreover, the length and the molecular structure of DNA and RNA can be used to manipulate the mechanical properties of these self-assembled films.