Generation and application of the twisted beam with orbital angular momentum

The twisted Laguerre-Gaussian beam was generated by transforming of Hermite-Gaussian beams through an optical system consisting of three rotated cylindrical lenses. The intensity distribution and phase structure of the twisted hollow beam were theoretically analyzed by using Collins diffraction integral. By utilizing the method of mode decomposition, the theory of transformation was analyzed. In the experiment, micro particles were trapped and rotated by this twisted beam.     

EXPERIMENTAL STUDY OF DIFFRACTIVE PROPERTIES OF WAVELENGTH-SIZED SINGLE GROOVE IN Si-Si3N4 SUBSTRATE

Experimental results are presented for the diffractive properties of wavelength-sized single groove in Si-Si₃N₄ substrate. The experimental results show that the diffraction of wavelength-sized single grooves in a non-perfectly conducting material is more complex than that of perfectly conducting material. The diffraction intensities change with the change of polarization angle of the incident light. The diffraction intensities for TM polarization light are larger as the groove width is larger. The diffraction intensities of TM polarization light decrease gradually and that of TE polarization light increase gradually when the groove width is close to the wavelength of the incident light. The variations of diffraction intensities are quite different not only for various grooves with different widths but also for different diffraction angles for the same groove. Although the intensity variation of each diffraction order has a very regular sinusoidal dependence on the polarization angles of the incident light, the variation phase of each diffraction order is not all the same.     

Beam steering characteristics in high-power quantum-cascade lasers emitting at∼4.6µm

A beam steering effect of high-power quantum cascade(QC) lasers emitting at 4.6 μm was investigated. The continuous wave(CW) output power of an uncoated, 6-mm-long, 7.5-μm-wide buried-heterostructure QC laser at 25℃ was as high as 854.2 m W. The maximum beam steering angle was offset by ±14.2° from the facet normal(0°) in pulsed mode. The phenomenon was judged explicitly by combining the diffraction limit theory and Fourier transform of the spectra. It was also verified by finite element method software simulation and the calculation of two-dimensional(2 D)effective-index model. The observed steering is consistent with a theory for coherence between the two lowest order lateral modes. Therefore, we have established an intrinsic linkage between the spectral instabilities and the beam steering by using the Fourier transform of the spectra, and further presented an extremely valid method to judge the beam steering. The content of this method includes both three equidistant peak positions in the Fourier transform of the spectra and the beam quality located between once the diffraction limit(DL) and twice the DL.     

Bi-photonic transient gratings in bulk azo-dye containing poly(methyl methacrylate) matrix

Amorphous bulk composites were prepared by doping azo-dye disperse red 1 (DR1) in poly(methyl methacrylate) (PMMA) matrices. Photoinduced anisotropy of such kind of bulk polymer material was investigated experimentally by measuring the dichroism when irradiating with linearly polarized green light with different polarization direction. With the interaction of bi-photonic beams at 514 and 632.8 nm,transient gratings in the bulk composites could be established, which was a kind of population gratings of trans and cis DR1 isomers and was attributed to the weak absorption of cis isomers at 632.8 nm and the positive dichroism of trans isomers at 514 nm. Furthermore, the all-optical switching behavior of the transient holographic gratings was observed repeatedly by turning on and off the writing beams and a response time of ten milliseconds order could be obtained.     

RAMAN SCATTERING OF α-ET3(ReO4)2 CHARGE-TRANSFER SALT

We describe the results of Haman studies on C=C stretch modes in α-ET₃(ReO₄)₂ charge-transfer salt with the incident laser beam polarised perpendicular and parallel to the large flat face of plate-like crystal. We have assigned central C=C stretch mode at 1454 cm^-1 and ring C=C stretch mode at 1470cm^-1. The change in ring C=C stretch vibration was observed at the metal-insulator transition of α-ET₃(ReO₄)₂ on warming due to the distortion of the ET molecules.     

Effects of high-dose Ge ion implantation and post-implantation annealing on ZnO thin films

This paper reports that ion implantation to a dose of 1×10¹⁷ ions/cm² was performed on c-axis-orientated ZnO thin films deposited on (0001) sapphire substrates by the sol-gel technique. After ion implantation, the as-implanted ZnO films were annealed in argon ambient at different temperatures from 600-900℃. The effects of ion implantation and post-implantation annealing on the structural and optical properties of the ZnO films were investigated by x-ray diffraction (XRD), photoluminescence (PL). It was found that the intensities of (002) peak and near band edge (NBE) exitonic ultraviolet emission increased with increasing annealing temperature from 600-900℃. The defect related deep level emission (DLE) firstly increased with increasing annealing temperature from 600- 750℃, and then decreased quickly with increasing annealing temperature. The recovery of the intensities of NBE and DLE occurs at \sim 850℃ and \sim 750℃ respectively. The relative PL intensity ratio of NBE to DLE showed that the quality of ZnO films increased continuously with increasing annealing temperature from 600 - 900℃.     

Identification of Above-Threshold Ionization by Imaging Photoelectrons from Ammonia Molecules in an Intense Femtosecond Laser Field

The above-threshold ionization process of ammonia molecules induced by a femtosecond laser field at 800 nm is studied in the intensity range from 1.6 × 10¹³ to 5.7 × 10¹³ W/cm². Channel switching under different laser intensities is observed and identified in the photoelectron kinetic energy spectra of ammonia. Based on the photoelectron kinetic energy distributions and the photoelectron angular distributions, the characteristic peaks observed are exclusively ass...     

FORMATION OF A BURIED LAYER OF ALUMINIUM NITRIDE BY HIGH DOSE N2+ IMPLANTATION INTO ALUMINIUM

Aluminium films with various thickness between 700 nm and 1μm were deposited on Si (100) substrates, and 400 keV N₂⁺ ions with doses ranging from 4.3×10¹⁷ to 1.8×10¹⁸ N/cm² were implanted into the alu-minium films on silicon, Rutherford Backscattering (RBS) and channeling, secondary ion mass spectroscopy (SIMS), Fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), transmission electron microscopy (TEM) and spreading resistance probes (SRP) were used to characterize the synthesized aluminium nitride. The experiments showed that when the implantation dose was higher than a critical dose N_c, a buried stoichiometric AlN layer with high resistance was formed, while no apparent AlN XRD peaks in the as-implanted samples were observed; however, there was a strong AlN(100) diffraction peak appearing after annealing at 500 ℃ for 1h. The computer program, Implantation of Reactive Ions into Silicon (IRIS), has been modified and used to simulate the formation of the buried AlN layer as N₂⁺ is implanted into aluminium. We find a good agreement between experimental measurements and IRIS simulation.     

Diffraction properties of four-petal Gaussian beams in uniaxially anisotropic crystal

Propagation properties of polarized four-petal Gaussian beams along the optical axis of uniaxially anisotropic crystals were investigated.Based on the paraxially vectorial theory of beam propagation, analytic expressions of the diffraction light field were obtained.The effects of the anisotropy on the po- larization properties of the diffracted four-petal Gaussian beams have also been explained by numerical method,The results elucidate that the linear polarization state and the symmetry of the incident beams cannot be kept during propagation in anisotropic crystals.     

Enhanced field emission characteristics of thin-Au-coated nano-sheet carbon films

This paper reports that the nano-sheet carbon films (NSCFs) were fabricated on Si wafer chips with hydrogen--methane gas mixture by means of quartz-tube-type microwave plasma chemical vapour deposition (MWPCVD). In order to further improve the field emission (FE) characteristics, a 5-nm Au film was prepared on the samples by using electron beam evaporation. The FE properties were obviously improved due to depositing Au thin film on NSCFs. The FE current density at a macroscopic electric field, E, of 9~V/μ m was increased from 12.4~mA/cm² to 27.2~mA/cm² and the threshold field was decreased from 2.6~V/μ m to 2.0~V/μ m for Au-coated carbon films. A modified F-N model considering statistic effects of FE tip structures in the low E region and a space-charge-limited-current effect in the high E region were applied successfully to explain the FE data of the Au-coated NSCF.     

Fragmentation of stable and neutron-rich 12-16C into boron fragments at approximately 240 MeV/nucleon

The elemental fragmentation cross sections of boron fragments produced by stable and neutron-rich^12-16C beams with a carbon target were systematically measured at an incident beam energy of approximately 240 MeV/nucleon.The measured cross sections were found to increase as the projectile mass number increases.The observed feature is explained qualitatively based on the abrasion-ablation two-stage reaction model and is compared quantitatively with predictions from various reaction models,including empirical and statistical models.All models agree with the measured cross sections within a factor of 2.     

Diffraction properties of four-petal Gaussian beams in uniaxially anisotropic crystal

Propagation properties of polarized four-petal Gaussian beams along the optical axis of uniaxially anisotropic crystals were investigated. Based on the paraxially vectorial theory of beam propagation, analytic expressions of the diffraction light field were obtained. The effects of the anisotropy on the polarization properties of the diffracted four-petal Gaussian beams have also been explained by numerical method. The results elucidate that the linear polarization state and the symmetry of the incident beams cannot be kept during propagation in anisotropic crystals.     

Self-polarization emission based on coherent combination of intracavity eigenmodes in Nd:YAG/Cr~(4+):YAG lasers

The behavior of self-polarization emission in Nd∶Y₃Al₅O₁₂(YAG)=Cr⁴⁺∶YAG lasers has been proved in some cases.However,the degree and direction of polarization were often sensitive and unstable.We experimentally observed different beam profiles versus the angle of the polarizer relative to the polarization direction of the laser.In order to explore the polarization mechanism,the dynamics of intracavity polarized eigenmodes was analyzed theoretically.Simulative results were well consistent with our experimental observations.It indicated that the linear self-polarization emission was a composite state rather than an intrinsic state.This study contributed to the improvement of the polarization stability in Nd∶YAG=Cr⁴⁺∶YAG passively Q-switched lasers.     

The research on suspended ZnO nanowire field-effect transistor

This paper reports that a novel type of suspended ZnO nanowire field-effect transistors (FETs) were successfully fabricated using a photolithography process, and their electrical properties were characterized by I--V measurements. Single-crystalline ZnO nanowires were synthesized by a hydrothermal method, they were used as a suspended ZnO nanowire channel of back-gate field-effect transistors (FET). The fabricated suspended nanowire FETs showed a p-channel depletion mode, exhibited high on--off current ratio of ～10⁵. When V_DS=2.5 V, the peak transconductances of the suspended FETs were 0.396 μS, the oxide capacitance was found to be 1.547 fF, the pinch-off voltage V_TH was about 0.6 V, the electron mobility was on average 50.17 cm²/Vs. The resistivity of the ZnO nanowire channel was estimated to be 0.96× 10²Ω cm at V_GS = 0 V. These characteristics revealed that the suspended nanowire FET fabricated by the photolithography process had excellent performance. Better contacts between the ZnO nanowire and metal electrodes could be improved through annealing and metal deposition using a focused ion beam.     

Spatial Splitting and Intensity Suppression of Four-Wave Mixing in V-Type Three-Level Atomic System

We illustrate our experimental observation of coexisting the controllable spatial splitting and intensity suppression of four-wave mixing （FWM） beam in a V-type three-level atomic system. The peak number and separation distance of the FWM beam are controlled by the intensities and frequencies of the laser beams, as well as atomic density.     

A novel orthogonally linearly polarized Nd:YVO4 laser

<正>We presented a novel orthogonally linearly polarized Nd:YVO₄ laser.Two pieces of a-cut grown-together composite YVO₄/Nd:YVO₄ crystals were placed in the resonant cavity with the c-axis of the two crystals orthogonally.The polarization and power performance of the orthogonally polarized laser were investigated.A 26.2-W orthogonally linearly polarized laser was obtained.The power ratio between the two orthogonally polarized lasers was varied with the pump power caused by the polarized mode coupling.The longitudinal modes competition and the corresponding variable optical beats were also observed from the orthogonally polarized laser.We also adjusted the crystals with their c-axis parallele to each other,and a 40.7-W linearly polarized TEMoo laser was obtained,and the beam quality factors were M_x²=1.37 and M_y² =1.25.     

Compact and efficient diode-pumped passively Q-switched Nd:GdVO_4 laser at 1.06μm

Diode-pumped passively Q-switched Nd:GdVO4/Cr4+:YAG lasers with a simple flat-flat cavity were demonstrated. The maximum average output power at 1.06 μm was 1.25 W. The highest peak power and pulse energy were 7.56 kW and 75μJ, respectively, with the pulse repetition rate of 11.1 kHz and pulse width of 10 ns at the incident pump power of 8 W.     

Effect of polarization on efficiency of volume Bragg grating filter

<正>Diffraction efficiency of volume Bragg grating,whose period is in the same order as the incident wavelength, is related to the polarization direction of the incident linear polarized beam.When two linearly polarized recording beams with the same polarization direction are used for recording volume Bragg gratings in a photopolymer with diffusion amplification,the azimuth of polarization of the reconstruction beam influences the diffraction efficiency of the grating.When the probe beam is linearly polarized and oriented orthogonally to the grating vectors,the±1-order diffraction beams are also linearly polarized with polarization direction parallel to that of the probe beam.According to the results,a two-dimensional nonspatial optical filter consisting of the volume Bragg gratings would achieve significantly higher efficiency.     

Longitudinal Schottky spectra of a bunched Ne10+ ion beam at the CSRe

The longitudinal Schottky spectra of a radio-frequency (RF) bunched and electron cooled ²²Ne¹⁰⁺ ion beam at 70 MeV/u have been studied by a newly installed resonant Schottky pick-up at the experimental cooler storage ring (CSRe), at IMP. For an RF-bunched ion beam, a longitudinal momentum spread of Δp/p=1.6×10^-5 has been reached with less than 10⁷ stored ions. The reduction of momentum spread compared with a coasting ion beam was observed from Schottky noise signal of the bunched ion beam. In order to prepare the future laser cooling experiment at the CSRe, the RF-bunching power was modulated at 25^th, 50^th and 75^th harmonic of the revolution frequency, effective bunching amplitudes were extracted from the Schottky spectrum analysis. Applications of Schottky noise for measuring beam lifetime with ultra-low intensity of ion beams are presented, and it is relevant to upcoming experiments on laser cooling of relativistic heavy ion beams and nuclear physics at the CSRe.     

A novel optical beam splitter based on photonic crystal with hybrid lattices

A novel optical beam splitter constructed on the basis of photonic crystal(PC) with hybrid lattices is proposed in this paper.The band gap of square-lattice PC is so designed that the incident light is divided into several branch beams.Triangular-lattice graded-index PCs are combined for focusing each branch.Computational calculations are carried out on the basis of finite-different time-domain algorithm to prove the feasibility of our design.The waveguide is unnecessary in the design.Thus the device has functions of both splitting and focusing beams.Size of the divided beam at site of full-width at half-maximum is of the order of λ/2.The designed splitter has the advantages that it has a small volume and can be integrated by conventional semiconductor manufacturing process.