椭偏透射法测量氢化非晶硅薄膜厚度和光学参数

针对多角度椭偏测量透明基片上薄膜厚度和光学参数时基片背面非相干反射光的影响问题,报道了利用椭偏透射谱测量等离子增强化学气相沉积法(PECVD)制备的a-Si:H薄膜厚度和光学参数的方法,分析了基片温度T_s和辉光放电前气体温度T_g的影响.研究表明,用椭偏透射法测量的a-Si:H薄膜厚度值与扫描电镜(SEM)测得的值相当,推导得到的光学参数与其他研究者得到的结果一致.该方法可用于生长在透明基片上的其他非晶或多晶薄膜. 关键词： 椭偏测量 透射法 光学参数 氢化非晶硅薄膜     

纳米ZnO和ZnO-SiO2复合薄膜的光学性质研究

通过溶胶凝胶(sol-gel)法分别在玻璃衬底上制备了ZnO纳米薄膜和ZnO-SiO₂纳米复合薄膜,并利用紫外-可见光分光光度计对薄膜的光学性能进行了分析.可见光-紫外透射谱显示,随着ZnO溶胶浓度从0.7mol/L降低到0.006mol/L,制备的ZnO薄膜从只出现一个380nm(对应的光学禁带宽度为3.27eV)左右的吸收边到在380和320nm(对应的光学禁带宽度为3.76eV)左右各出现一个吸收边,并且随着ZnO溶胶浓度的降低,在380—320nm波段内的透过率明显提高.而Z 关键词： 纳米ZnO 2复合薄膜')" href="#">ZnO-SiO₂复合薄膜 溶胶凝胶法 透射率     

Thermal and optical properties of Cd2SnO4 thin films using photoacoustic spectroscopy

Cadmium stannate (Cd₂SnO₄) thin films were prepared by the RF magnetron sputtering technique on glass substrates with substrate temperatures of room temperature (RT), 100°C, 200°C and 300°C. Photoacoustic analyses were made to obtain the thermal diffusivity and the optical bandgap values of the Cd₂SnO₄ thin films. The change in thermal diffusivity of the films with the substrate temperature was analyzed. The optical bandgap values obtained from the photoacoustic spectroscopy were compared with the values obtained from the optical transmittance spectra. X-ray photoelectron spectroscopic (XPS) studies confirm the formation of stoichiometric films. Surface morphological studies by atomic force microscopy (AFM) revealed the crystalline nature of the films deposited at 100°C.     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

电泳沉积法制备V2O5薄膜的结构和性能

将V2O5溶胶电泳沉积在ITO导电基片上制备V2O5薄膜.运用X射线衍射和扫描电镜对薄膜的结构进行分析,通过紫外-可见光透射光谱和循环伏安法分别测试其光学和电化学性能.实验结果表明,电泳沉积V2O5薄膜具有致密的显微结构,薄膜厚度均匀、与基片的粘附性很好;循环实验中,薄膜呈现黄色到绿色的可逆变化,最大的透射率变化达到30%左右;薄膜具有很好的注入/退出可逆性和循环稳定性,50次循环效率仍能达到88.02%,并且循环后的薄膜与ITO导电玻璃的粘附性仍然很好,没有溶解现象;应用交流阻抗法计算Li+在V2O5薄膜着色过程的扩散系数为5.10×10-12cm2/s,表明该薄膜可以作为电致变色材料得到应用.     

Optical characterization of thin thermal oxide films on copper by ellipsometry

A complete optical characterization in the visible region of thin copper oxide films has been performed by ellipsometry. Copper oxide films of various thicknesses were grown on thick copper films by low temperature thermal oxidation at 125 °C in air for different time intervals. The thickness and optical constants of the copper oxide films were determined in the visible region by ellipsometric measurements. It was found that a linear time law is valid for the oxide growth in air at 125 °C. The spectral behaviour of the optical constants and the value of the band gap in the oxide films determined by ellipsometry in this study are in agreement with the behaviour of those of Cu₂O, which have been obtained elsewhere through reflectance and transmittance methods. The band gap of copper oxide, determined from the spectral behaviour of the absorption coefficient was about 2 eV, which is the generally accepted value for Cu₂O. It was therefore concluded that the oxide composition of the surface film grown on copper is in the form of Cu₂O (cuprous oxide). It was also shown that the reflectance spectra of the copper oxide–copper structures exhibit behaviour expected from a single layer antireflection coating of Cu₂O on Cu. Received: 19 July 2001 / Accepted: 27 July 2001 / Published online: 17 October 2001     

Characteraction of Ag-doped ZnO thin film synthesized by sol–gel method and its using in thin film solar cells

Pure 2% and 4% Ag-doped ZnO thin films have been synthesized on glass substrates by sol–gel method. The structure, morphology and optical properties of the samples have been studied by X-ray diffractometer (XRD), scanning probe microscope, UV–vis spectrophotometer, respectively. The XRD result shows that the pure ZnO has a wurtzite hexagonal structure, no phase segregation is observed. The surface morphology of pure ZnO thin film shows that the grains are growing preferentially along the c-axis orientation perpendicular to the substrates. The transmittance spectra reveal that all samples have high transmittance above 90% in visible region. With Ag doping content increase, a red shift is observed. The performance of Ag-doped ZnO films using in thin film solar cells are simulated. The results show that 4% Ag-doped ZnO thin film can greatly improve the absorption of the cells. Compare to pure ZnO, solar cell's energy conversion efficiency improvement of 2.47% is obtained with 4% Ag doped ZnO thin film.     

Influence of oxygen pressure of ZnO/glass substrate produced by pulsed filtered cathodic vacuum arc deposition

The effects of oxygen pressure on the structural and optical properties of high quality transparent conductive ZnO thin films were studied in detail. ZnO thin films were prepared by pulsed filtered cathodic vacuum arc deposition system under various oxygen pressures on glass substrate at room temperature. With increasing oxygen pressure, the structure and optical properties of films change. The structural and optical properties of the ZnO thin films were investigated using X-ray diffraction, transmittance spectrometry, refractive index, oscillator parameters, energy band gap and Urbach tail. The films show c-axis oriented (0 0 2) hexagonal wurtize crystal structure. It has been found that the grain size of ZnO thin films increases from 16.9 to 22.6 nm with the increase of oxygen pressure from 3.8×10⁻⁴ to 6.9×10⁻⁴ Torr and the crystallinity is enhanced. Average transmittance is about 90% in the visible region of the ZnO thin films. From optical transmittance spectra of ZnO films, the absorption edge shifts towards the taller wavelength with an increase in oxygen pressure. The energy band gap decreases from 3.31 to 3.20 eV with an increase in oxygen pressure. The packing density investigation shows in ZnO films high packing densities (above 0.78) can be obtained.     

Optical and mechanical properties of AlF3 films produced by pulse magnetron sputtering of Al targets with CF4/O2 gas

In this study, AlF₃ thin films were deposited by pulse magnetron sputtering of Al targets with different ratios of CF₄/O₂ gas and at different sputtering powers. The optical and mechanical properties of the AlF₃ thin films were analyzed. The transmittance spectra showed no obvious negative inhomogeneous refractive indices. Denser films with a low optical absorption were obtained when high sputtering powers were used (larger than 30 W). The lowest extinction coefficient (7.3 × 10⁻⁴ at 193 nm) of the films can be reached with 12 sccm O₂ flow rate and at 160W sputtering power. All of the residual stresses were compressive and their trends were consistent with the refractive indices. The lowest compressive stress (0.068 GPa) was obtained when the AlF₃ films were prepared at 160W sputtering power.     

Structural,optical and electrical properties of tin oxide thin films by electrostatic spray deposition

Tin oxide (SnO₂) thin films were deposited by electrostatic spray deposition (ESD). The structural, optical and electrical properties of the films for different solvents were studied. The morphology of the deposited thin films was investigated by scanning electron microscopy. The optical transmission spectra of the films showed 66–75% transmittance in the visible region of spectrum. The electrical resistivity of thin films deposited using the different solvents ranged 1.08 × 10^?3–1.34 × 10^?3 Ω-cm. Overall, EG and PG were good solvents for depositing SnO₂ thin films by the ESD technique with stable cone jet.     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Influence of thickness on the optical properties of amorphous GeSe2 thin films: analysis using Raman spectra,Urbach energy and Tauc parameter

An analysis is reported of thickness-induced defects in amorphous GeSe₂ thin films deposited by the vacuum evaporation technique. X-ray diffraction studies confirmed the amorphous nature of the thin films. Optical absorption measurements revealed an indirect transition with an energy gap that increases with film thickness. A blue shift in optical transmittance edges was observed in annealed GeSe₂ thin films. The obtained lower values of Urbach energy (E _U) indicate that as thickness increases more ordered films can be produced. Raman spectra suggest that annealing promotes corner-sharing GeSe_4/2 tetrahedra and edge-sharing Ge₂Se_8/2 bi-tetrahedra bonding and leads to the reduction in disorder in bonding network, which is amply supported by the way of increase in band gap, increase in Tauc parameter (B ^1/2) and reduction in E _U from the analysis of transmittance spectra. Increasing the thickness promotes tetrahedral and bi-tetrahedral bonding through the reduction in bonding defects.     

Structural and optoelectronic properties of amorphous GaN thin films

Amorphous gallium nitride (a-GaN) thin films were deposited on glass substrate by electron beam evaporation technique at room temperature and high vacuum using N ₂ as carrier gas. The structural properties of the films was studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). It was clear from XRD spectra and SEM study that the GaN thin films were amorphous. The absorbance, transmittance and reflectance spectra of these films were measured in the wavelength range of 300–2200 nm. The absorption coefficient spectral analysis in the sharp absorption region revealed a direct band gap of E _g = 3:1 eV. The data analysis allowed the determination of the dispersive optical parameters by calculating the refractive index. The oscillator energy E ₀ and the dispersion energy E _d, which is a measure of the average strength of inter-band optical transition or the oscillator strength, were determined. Electrical conductivity of a-GaN was measured in a different range of temperatures. Then, activation energy of a-GaN thin films was calculated which equalled E _a = 0:434 eV.     

锂离子注入对V2O5薄膜光吸收的影响

采用真空蒸发经热处理制备了Ｖ２Ｏ５薄膜,使用二电极恒流法从１Ｍ／ＬＬｉＣｌＯ４的ＰＣ电解质溶液向Ｖ２Ｏ５薄膜注入锂离子,形成ＬｉｘＶ２Ｏ５（０≤ｘ≤０．５４）,测量了Ｖ２Ｏ５薄膜近垂直反射和透射光谱,计算了光吸收系数。Ｘ射线衍射分析表明薄膜为微晶结构。吸收系数与光子能量关系曲线中存在两个不同的变化区域,光子能量较高部分,（αｈν）１２与ｈν有线性关系;较低部分,吸收光谱存在一个尾巴。这两个区域的分界能量取决于电子和锂离子的注入量。研究结果表明Ｖ２Ｏ５薄膜阳极电致变色起源于吸收边缘的移动,而阴极电致变色则来源于小极化子的吸收     

Structural and optical properties of ZnO thin films on (111) CaF2 substrates grown by magnetron sputtering

ZnO thin films were grown on (111) CaF₂ substrates by magnetron sputtering at room temperature. Structural and optical properties of the ZnO thin films were studied. XRD analysis showed that the ZnO thin films had the (002) preferential orientation. The transmittance of ZnO thin films was over 80% in the visible range. The optical band gap of the ZnO thin films was 3.26 eV. The optical constants (n,k)$(n,k)$ of the ZnO thin films in the wavelength range 300–1000 nm were obtained by infrared spectroscopic ellipsometry measurement. PL spectra of ZnO thin films showed strong UV near-band-edge emission peak at 376.5 nm and weak visible red emission at 643.49 nm using He–Cd laser as the light source, using a synchrotron radiation light source PL spectra showed three emission peak at 320 nm, 410 nm and 542 nm respectively.     

Optical properties of thin films of closely packed SiO2 spheres

Ordered, closely packed, defect-free one-, two-, and three-layer thick films of SiO₂ spheres of diameter D varying from 0.6 to 1.4 μm were obtained. Their optical transmittance and reflectance spectra were measured in the range 0.3–2.5 eV. The one-layer structures reveal a transmittance minimum whose spectral position is described by the Bragg law with the plane separation equal to the sphere radius D/2. As the number of the layers increases, a spectral feature appears which signals the formation of a photonic gap in the 〈111〉 direction of the fcc crystal lattice and is determined by the distance between the {111} planes equal to 0.816D. The spectra of two-and three-layer structures measured with a diverging light beam contain additional lines originating from the formation of photonic gaps by the {111} and {221} planes. __________ Translated from Fizika Tverdogo Tela, Vol. 44, No. 6, 2002, pp. 1026–1031. Original Russian Text Copyright ? 2002 by Bazhenov, Gorbunov, Aldushin, Masalov, Emel’chenko.     

Ag掺杂p型ZnO薄膜及其光电性能研究

采用超声喷雾热分解法在石英衬底上以醋酸锌水溶液为前驱体,以硝酸银水溶液为Ag掺杂源生长了Ag掺杂ZnO(ZnO：Ag)薄膜.研究了衬底温度对所得ZnO：Ag薄膜的晶体结构、电学和光学性质的影响规律.所得ZnO：Ag薄膜结构良好,在室温光致发光谱中检测到很强的近带边紫外发光峰,透射光谱中观测到非常陡峭的紫外吸收截止边和较高的可见光区透过率,表明薄膜具有较高的晶体质量与较好的光学特性.霍尔效应测试表明,在500℃下获得了p型导电的ZnO：Ag薄膜,载流子浓度为5.30×10¹⁵cm关键词： ZnO：Ag薄膜 p型掺杂 超声喷雾热分解 霍尔效应     

Effects of the substrate and oxygen partial pressure on the microstructures and optical properties of Ti-doped ZnO thin films

Ti-doped ZnO (ZnO:Ti) thin films were deposited on the glass and Si substrates using radio frequency reactive magnetron sputtering. The effects of substrate on the microstructures and optical properties of ZnO:Ti thin films were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and a fluorescence spectrophotometer. The structural analyses of the films indicated that they were polycrystalline and had a hexagonal wurtzite structure on different substrates. When ZnO:Ti thin film was deposited on Si substrate, the film had a c-axis preferred orientation, while preferred orientation of ZnO:Ti thin film deposited on glass substrate changed towards (1 0 0). Finally, we discussed the influence of the oxygen partial pressures on the structural and optical properties of glass-substrate ZnO:Ti thin films. At a high ratio of O₂:Ar of 18:10 sccm, the intensity of (0 0 2) diffraction peak was stronger than that of (1 0 0) diffraction peak, which indicated that preferred orientation changed with the increase of O₂:Ar ratios. The average optical transmittance with over 93% in the visible range was obtained independent of the O₂:Ar ratio. The photoluminescence (PL) spectra measured at room temperature revealed four main emission peaks located at 428, 444, 476 and 527 nm. Intense blue-green luminescence was obtained from the sample deposited at a ratio of O₂:Ar of 14:10 sccm. The results showed that the oxygen partial pressures had an important influence for PL spectra and the origin of these emissions was discussed.     

The characteristics of Au:VO2 nanocomposite thin film for photo-electricity applications

Au nanoparticles have been fabricated on normal glass substrates using nanosphere lithography (NSL) method. Vanadium dioxide has been deposited on Au/glass by reactive radio frequency (rf) magnetron sputtering. The structure and composition were determined by X-ray diffraction and X-ray photoelectron spectroscope. Electrical and optical properties of bare VO₂ and Au:VO₂ nanocomposite thin films were measured. Typical hysteresis behavior and sharp phase transition were observed. Nanopartical Au could effectively reduce the transition temperature to 40 °C. The transmittance spectrum for both Au:VO₂ nanocomposite thin film shows high transmittance under transition temperature and low transmittance above transition temperature. The characteristics present the Au:VO₂ nanocomposite thin film can be used for applications, such as “smart window” or “laser protector”.