Microwave nonlinearity measurements of epitaxial YBa2Cu3O7−x thin film by bridged resonator

A simple bridged resonator method is presented for microwave nonlinearity measurement of epitaxial superconductor thin film. By this method, microwave current is concentrated in local bridged part on the resonator, and local inductive and resistive nonlinearity in this part are measured. At the same time, undesired nonlinearity are eliminated from the tested results by the special current distribution of the resonator, which enhances the accuracy of the measured nonlinearity.     

Multiferroic properties of sol-gel derived Bi5Fe1-xCoxTi3O15 thin films

Co-doped Bi 5 FeTi 3 O 15 thin films (BFCT-x,Bi 5 Fe 1-x Co x Ti 3 O 15) were prepared using a sol-gel technique.XRD patterns confirm their single phase Aurivillius structure,and the corresponding powder Rietveld analysis indicates the change of space group around x=0.12.The magnetic hysteresis loops are obtained and ferromagnetism is therefore confirmed in BFCT-x thin films.The remanent magnetization (M r) first increases and reaches the maximum value of 0.42 emu/cm 3 at x=0.12 due to the possible Fe 3+-O-Co 3+ ferromagnetic coupling.When x=0.25,the M r increases again because of the dominant Fe 3+-O-Co 3+ ferromagnetic coupling.The remanent polarization (2P r) of BFCT-0.25 was measured to be as high as 62 μC/cm 2,a 75% increase when compared with the non-doped BFCT-0 films.The 2P r remains almost unchanged after being subjected to 5.2 × 10 9 read/write cycles.Greatly enhanced ferroelectric properties are considered to be associated with decreased leakage current density.     

氧气分压对TiO2薄膜结构、磁性及输运性质的影响

采用脉冲激光沉积技术在LaAlO_3(100)基片上制备了TiO_2薄膜,研究了氧气分压对薄膜结构、磁性与输运性质的影响.结构测量表明,TiO_2薄膜的结构与沉积过程中的氧气分压有关,氧气分压的增大有利于薄膜向锐钛矿相转变.磁性测量表明,在较高的氧气分压下制备的TiO_2薄膜表现为顺磁性,在较低氧气分压下制备的TiO_2薄膜表现出明显的室温铁磁性,其铁磁性与氧空位有密切关系.输运测量进一步表明,TiO_2薄膜表现为半导体导电特性,在具有铁磁性的薄膜中还观察到了低温磁电阻效应.     

Microstructure and microwave permeability of FeCo thin films with Co underlayer

Microstructure, static magnetic properties and microwave permeability of sputtered FeCo films were examined. Fe₆₀Co₄₀ films (100 nm in thickness) deposited on glass substrates exhibited in-plane isotropy and a large coercivity of 161.1 Oe. When same thickness films were deposited on 2.5 nm Co underlayer, well-defined in-plane anisotropy was formed with an anisotropy field of 65 Oe. The sample had a static initial permeability of about 285, maximum imaginary permeability of 1255 and ferromagnetic resonance frequency of 2.71 GHz. Cross-sectional TEM image revealed that the Co underlayer had induced a columnar grain structure with grain diameter of 10 nm in the FeCo films. In comparison, FeCo films without Co underlayer showed larger grains of 70 nm in diameter with fewer distinct vertical grain boundaries. In addition, the Co underlayer changed the preferred orientation of the FeCo from (1 0 0) to (1 1 0). The improvement in soft magnetic properties and microwave behavior originates from the modification of the film microstructure, which can be well understood by the random anisotropy theory.     

激励表面等离子共振的金属薄膜最佳厚度分析

根据电磁场在金属薄膜中的能量分布规律和金属薄膜具有复介电常数的特点,对激励表面等离子共振的金属薄膜的最佳厚度进行了探讨. 指出金属薄膜的最佳厚度与激励光波长和金属薄膜的折射率有关,建立了描述它们之间关系的数学表达式,并用实验方法进行验证. 将理论结果与他人的测量结果进行对比后发现,两者符合较好. 研究结果表明：在角度调制下的表面等离子共振传感器,为了获得更高的灵敏度,可根据激励光波长和金属薄膜折射率的虚部确定所要制备金属薄膜的最佳厚度;在波长调制下,则由中心波长和折射率的虚部确定金属薄膜的最适宜使用厚度. 关键词： 折射率 金属薄膜 全内反射 表面等离子共振     

Properties of electropolymerised polypyrrole thin film on silver

This paper reports the properties of electropolymerised polypyrrole thin film on silver. The transmission, reflection, conductivity and dielectric behavior of polypyrrole coated silver has been studied in the 8-12 GHz frequency range of the electromagnetic spectrum. The polypyrrole thin film makes silver a better conductor for microwaves. The microwave conductivity is larger than the DC conductivity by many orders of magnitude. The real and imaginary part of dielectric constant increases in magnitude with increasing doping level and also it decreases in magnitude with increasing frequency.     

Simulation analysis of the aluminum thin film thickness measurement by using low energy electron beam

This paper indicates a simulation analysis for estimating the aluminum (Al) thin film thickness measurements by using the low energy electron beam. In order to calculate the Al thickness estimation, the energy of the incident electron beams was varied from 10 to 30 keV, while the thickness of the Al film was varied between 6 and 14 μm. From the simulation results it was found that electron transmittance fraction in 14 μm sample is about nine orders of magnitude more than 6 μm sample at the same incident electron beam energy. Simulation results show that maximum transmitted electrons versus Al layer thickness has a parabolic relation and by using the obtained equation, it is possible to estimate unknown thickness of the thin film Al layer. All calculations here were done by CASINO numerical simulation package.     

Characterization of magnetic materials by low-field microwave absorption techniques

A low-field non-resonant microwave absorption has recently been observed in a variety of magnetically ordered materials at low DC fields (−1000 Oe H_DC+1000 Oe), which is known as low-field microwave absorption (LFA). It has been shown that LFA is essentially similar to giant magnetoimpedance (GMI), and clearly different from ferromagnetic resonance (FMR). LFA strongly depends on the anisotropy field of the sample. In contrast with FMR (which can be described as the homogeneous precession of spins in the saturated state), LFA can be thought as a spin rotation process occurring during the magnetic saturation. In this work, we present a detailed study of the basic features of LFA in several types of materials: ferrites and amorphous microwires and ribbons; in particular the effects sample shape, temperature up to the Curie transition, the influence of easy axis and the effects of annealings. These examples show that once LFA is fully understood, it can become a powerful characterization tool.     

利用泄漏波导测量低折射率薄膜的折射率和厚度

根据泄漏波导原理对K_9玻璃基板上的冰晶石薄膜进行折射率测量,达到的精度为1×10~(-4),与真实波导的情况相似。文中讨论了利用添加高折射率薄层减小待测薄膜的最小厚度的可能性。文中还利用光电方法观察反射光中暗条纹的方法判别波导的激发,并测出了冰晶石薄膜在4500到6500范围内的折射率。     

铜膜中锂离子扩散的第一性原理研究

基于第一性原理，采用“adiabatic trajectory”方法计算了锂离子在铜膜中的扩散势垒。通过比较可能的扩散机制，理论上证实了室温下锂离子可以最近邻空位扩散机制穿过铜膜。同时，解释了随着铜膜中空位数量的增加，锂离子的扩散势垒减小，从而更易在铜膜中扩散的物理现象。     

Plasmon resonance modulated photoluminescence and Raman spectroscopy of diindenoperylene organic semiconductor thin film

In a comparison between a bare diindenoperylene (DIP) film and a DIP film spin-coated with a layer of gold nanoparticles, we have investigated the influence of plasmon resonances in the gold particles on spectroscopic properties of the molecular film. Under off-resonant excitation with a laser at 633 nm, the bare DIP film showed only weak photoluminescence (PL) and Raman signals, but after spin-coating gold nanoparticles on such a DIP film, we found an enhancement of both the PL and Raman signals by a factor of about 3, whereas no enhancement could be observed when the same sample was excited with laser light of 488 nm. This difference reveals that at 633 nm, plasmon resonances in the gold nanoparticles are excited, leading in turn to an enhancement of PL and Raman signals of the weakly absorbing DIP film via coupling between plasmons in the gold particles and exciton-polaritons in the molecular film. For the laser at 488 nm, due to a much larger absorption coefficient of DIP, excitons in the molecular film are directly excited, out-weighing the influence of an off-resonant coupling to the plasmon resonances in the gold particles occurring at much lower energy.     

Determination of thin film refractive index and thickness by means of film phase thickness

A new approach for determination of refractive index dispersion n(λ) (the real part of the complex refractive index) and thickness d of thin films of negligible absorption and weak dispersion is proposed. The calculation procedure is based on determination of the phase thickness of the film in the spectral region of measured transmittance data. All points of measured spectra are included in the calculations. Barium titanate thin films are investigated in the spectral region 0.38–0.78 μm and their n(λ) and d are calculated. The approach is validated using Swanepoel’s method and it is found to be applicable for relatively thin films when measured transmittance spectra have one minimum and one maximum only.      

N掺杂SiO2纳米薄膜的制备及其磁性

利用射频磁控反应溅射技术,制备了氮掺杂的SiO₂纳米薄膜.发现N掺杂SiO₂体系纳米薄膜具有铁磁性.较小的氮化硅颗粒均匀分布在氧化硅基质中有利于磁有序的形成.基底温度为400℃时,样品薄膜具有最大的饱和磁化强度和矫顽力,分别为35 emu/cm³和75 Oe.薄膜的磁性可能产生于氮化硅和氧化硅的界面.理论计算表明,N掺杂SiO₂体系具有净自旋.同时,由氮化硅和氧化硅界面之间的电荷转移导致的轨道磁矩也会对样品的磁性有贡献 关键词： 2薄膜')" href="#">N掺杂SiO₂薄膜 射频磁控反应溅射 界面磁性 基底温度     

Synthesis of pyrochlore tungsten trioxide thin film and electrochemical lithium intercalation

The pyrochlore tungstate thin film has been prepared by an autoclave hydrothermal method at a temperature of 200 °C. The film was characterized by X-ray diffractometry, X-ray photoelectron spectroscopy and scanning electron micrograph measurements, showing that pure pyrochlore phase of sodium tungstate containing a small amount of water was formed by heating the film at a temperature of 350 °C. The cyclic voltammetric and galvanostic measurements revealed that a reversible electrochemical lithium intercalation into the crystal lattice of pyrochlore tungstate film takes place with charge-discharge cycling. Furthermore, the thermodynamics and kinetics of electrochemical lithium intercalation into the pyrochlore sodium tungstate film were also studied.     

用准对称波导法测量薄膜参数

本文指出了在棱镜耦合状态下降低平板波导基模截止厚度的途径,用文中提出的准对称波导法测量了薄的MgO膜的折射率和厚度,并给出了测量结果.     

Confined states and spin polarization on a topological insulator thin film modulated by an electric potential

We study the electronic structure and spin polarization of the surface states of a three-dimensional topological insulator thin film modulated by an electrical potential well. By routinely solving the low-energy surface Dirac equation for the system, we demonstrate that confined surface states exist, in which the electron density is almost localized inside the well and exponentially decayed outside in real space, and that their subband dispersions are quasilinear with respect to the propagating wavevector. Interestingly, the top and bottom surface confined states with the same density distribution have opposite spin polarizations due to the hybridization between the two surfaces. Along with the mathematical analysis, we provide an intuitive, topological understanding of the effect.     

Effect of film thickness on interface and electric properties of BiFeO3 thin films

Bismuth ferrite (BFO) thin films were fabricated by RF-magnetron sputtering deposition method on Pt/Ti/SiO₂/Si(1 0 0) substrate. The effect of the thickness of BFO films varying from 85 to 280 nm on electrical properties was investigated. Saturated coercive fields were found to increase with the BFO film thickness. The dielectric constant of BFO thin films measured at 1 kHz decreased with decreasing thickness from 98 to 86, while tangent losses increased from 0.013 to 0.021. The presence of bismuth oxide at the interface between BFO films and Pt bottom electrodes was responsible for the high leakage currents in thin BFO thin films as was demonstrated by X-ray diffraction, grazing-incident X-ray diffraction, and secondary ion mass spectroscopy analysis.     

Multiferroic properties of solben gel derived Bi5Fe1-xCoxTi3O15 thin films

Co-doped Bi₅FeTi₃O₁₅ thin films (BFCT-x, Bi₅Fe_1-xCo_xTi₃O₁₅) were prepared using a sol—gel technique. XRD patterns confirm their single phase Aurivillius structure, and the corresponding powder Rietveld analysis indicates the change of space group around x=0.12. The magnetic hysteresis loops are obtained and ferromagnetism is therefore confirmed in BFCT-x thin films. The remanent magnetization (M_r) first increases and reaches the maximum value of 0.42 emu/cm³ at x=0.12 due to the possible Fe³⁺—O—Co³⁺ ferromagnetic coupling. When x = 0.25, the M_r increases again because of the dominant Fe³⁺—O—Co³⁺ ferromagnetic coupling. The remanent polarization (2P_r) of BFCT-0.25 was measured to be as high as 62 μC/cm², a 75% increase when compared with the non-doped BFCT-0 films. The 2P_r remains almost unchanged after being subjected to 5.2 × 10⁹ read/write cycles. Greatly enhanced ferroelectric properties are considered to be associated with decreased leakage current density.     

记录薄膜Te—In—Sb光学性质的研究

采用高频溅射方法制成Te-In-Sb系统的非晶态薄膜.系统的研究了不同组分薄膜的透射、反射谱,及其在结晶过程中的变化.用透射电镜研究了Te-In-Sb薄膜的结构和晶化过程.分析了组分对薄膜的吸收系数、介电常数、光学能隙等光学性质的影响.并由此综合评价了Te-In—Sb系统中比较适合作为光盘介质的组成.