Mode-order converter in a multimode waveguide

A novel device that converts the order of modes in an integrated-optic multimode waveguide was proposed and fabricated. The device consists of two mode splitters and tapered waveguides. Its operation at a wavelength of 1.55 microm was confirmed by observation of the output mode profiles. The cross talk measured by an indirect method was >10.2 dB. The excess loss with reference to a straight multimode waveguide was 1.5 dB, compared with the propagation loss of a straight multimode waveguide.     

基于自映像的光子晶体波导分束器的设计

通过研究2维正方晶格光子晶体波导多模干涉的自映像效应,优化设计了一种新型1×2光子晶体波导分束器,采用时域有限差分法对其传输特性进行模拟分析。设计过程中,根据多模干涉耦合区中周期出现的双重像的位置确定两个单模输出波导的位置,通过在分束器输入和输出耦合区的连结处设置介质柱,改变输入和输出耦合区中的模场分布,实现模式匹配,从而明显减小分束器的反射损耗。计算结果表明:设置的介质柱归一化半径分别为0.08和0.177时,对于波长为1.55μm的入射光,该分束器的透射率可高达93%。     

Losses of optical multimode strip-waveguides made by thick film technology

Loss measurements on straight and curved multimode strip-waveguides made from photosensitive sheets by a photolithographic process are reported. The cross section of the waveguides vary from 20 μm × 50 μm to 100 μm × 100 μm. The loss is detected by measuring the light scattered out of the waveguide. Waveguides fabricated by a modified technology are compared to conventional ones at wavelengths of 0.633 μm and 0.83 μm. Using the modified technology losses of 2 dB/cm at λ = 0.83 μm have been measured for both straight and curved (radius 30 mm) guides.     

组合型TM01-TE11弯形圆波导模式转换器研究

 研究了组合型TM₀₁-TE₁₁弯形圆波导模式转换器（两弯曲段中间加一段直圆波导），在保持其输出与输入端口轴线平行的前提下，分别从理论推导、数值计算、软件模拟三个方面对此结构进行了分析，模拟结果与数值计算结果吻合得很好。结果表明：计及功率损耗，频率为3.75 GHz，铜波导内径为9.0 cm，轴向间距为10.57 m时，模式转换器总的功率转换效率为93.8%。     

Analysis of electrooptically induced waveguides in strontium barium niobate and optical modulators

An electrooptically induced optical waveguide can be formed by applying a DC voltage between electrodes fabricated on the surface of a crystal with strong electrooptic coefficients (for example, strontium barium niobate). Calculations of the refractive index profile and the optical mode size for such waveguides are presented. Approximate solutions for the fundamental mode are used to analyse the power coupling between a single-mode step-profile fibre and these waveguides. The power transmission losses in the straight and S-shaped waveguides are estimated by using a finite-difference beam propagation method (FD-BPM). The calculations predict that a new kind of modulator/switch can be realized with the induced waveguides. The important characteristics of these devices are discussed and compared with LiNbO₃ optical waveguide modulators.     

Impact of waveguide sidewall roughness on the output uniformity and phase of MMI splitters

In this paper, we develop a model for the effects of waveguide sidewall roughness on the output uniformity and phase of a 3-dB MMI splitter. We achieve this by investigating analytically the effect of sidewall roughness on mode coupling in the MMI section of the splitter using the coupled mode and coupled power equations. Using these equations, the subsequent impact of mode coupling losses on the splitter output uniformity and phase is calculated and results for 1 × 2 and 2 × 2 splitters are presented and compared. Finally, to illustrate the impact of sidewall roughness on the operation of a waveguide device, the response of a Mach Zehnder interferometer comprising 2 × 2 splitters is investigated.     

Beam Steering Type of 1 : 4 Optical Switch Using Thermo-Optic Effect

We propose a beam steering type optical switch employing a phase shifter. It consists of collimating waveguide mirrors, an arrayed-waveguide which has deep trenches incorporating polymer materials, and input/output waveguides. The incident light is guided to the front mirror, where it is then collimated, and input to the arrayed waveguide. The number of trenches filled with polymer linearly increases in order. The refractive index of the polymer can be controlled with temperature, and the propagation direction of the output light from the arrayed waveguide can also be controlled. A switch with 15 waveguides in the array has been fabricated. The chip size is about 2:5 × 9:0 mm², the insertion loss is 10 dB, and the extinction ratio is about 10–13 dB.     

微细笔直写聚合物条形光波导的研究

提出一种采用微细笔直写技术直写聚合物光波导的简便方法，利用该技术成功直写出了氟化聚酰胺条形光波导，并着重研究了气体压力和直写速度对波导宽度的影响规律。实验结果表明：直写获得的条形波导的边缘整齐、表面光滑，而且不存在小孔等缺陷或杂质。当其他工艺参数不变的情况下，波导宽度随着气体压力的增加而增大，随着直写速度的增大而减小。微细笔直写获得的条形光波导成功地实现了通光，在波长为1550nm处的最小传输损耗为0.59dB/cm。     

Analysis and optimization of an InGaAsP/InP waveguide variable optical attenuator

An InGaAsP/InP waveguide variable optical attenuator (VOA) is proposed in this paper. The device consists of straight input and output waveguides and an S-bend waveguide. An electrode is deposited on a portion of the waveguide to form an active region so that its refractive index can be modified by a current injection, resulting in the variation of the transmitted optical power. The beam propagation method is employed in the numerical simulation and the device structure is optimized using a genetic algorithm. The optimized VOA has a low excess loss (<1 dB) and a large dynamic range of about 40 dB.     

Optical waveguide fabrication and integration with a micro-mirror inside photosensitive glass by femtosecond laser direct writing

Photosensitive glass is a potentially important material for micro-fluidic devices that can be integrated with micro-optical components for biochemical analysis. Here, we demonstrate the fabrication of optical waveguides inside glass by femtosecond laser direct writing. The influence of the laser parameters on the waveguide properties is investigated, and it is revealed that the waveguide mode can be well controlled. The single mode is achieved at a low writing energy, while the multimode is achieved with increasing energy. In spite of a longitudinally elongated elliptical shape of the cross-sectional profile, the far-field pattern of the single-mode waveguide shows an almost symmetric profile. The measured propagation loss and the coupling loss are evaluated to be ∼0.6 dB/cm and ∼1.6 dB at a wavelength of 632.8 nm, respectively, under the conditions of 1.0–2.0 μJ pulse energy and 200–500 μm/s scan speed. The increased optical loss is associated with a higher waveguide mode at higher writing energy. Furthermore, the integration of waveguides and a micromirror made of a hollow microplate inside the glass is demonstrated to bend the laser beam at an angle of 90° in a small chip. The bending loss is estimated to be smaller than 0.3 dB. PACS 42.62.-b; 42.82.Cr; 82.50.Pt; 42.79.Gn; 42.81.Qb     

一种分析三维楔脊形光波导与光纤耦合的方法

和直波导的不同在于，三维楔脊形波导中的光场都是不稳定的.分别对波导-光纤耦合、光纤-波导耦合两种情况，将三维楔脊形波导等效为多段短的直波导，利用束传播法同时对三维楔脊形波导内不稳定的入射、反射场，及它们在传播方向上的偏导进行处理，再用自由空间辐射模法计算透射率和反射率.以SOI楔脊形波导和光纤的耦合为例，验证了该方法的可行性. 关键词： 自由空间辐射模法 束传播法 耦合 透射 楔脊形光波导 绝缘体上硅(SOI)     

Property study of Si + -ion-implanted Nd:YVO 4 waveguides

Planar waveguides were formed in Nd:YVO₄ crystals by 3.0-MeV Si⁺-ion implantation at doses of 1×10¹³–1.5×10¹⁵ ions/cm² at room temperature. The effective refractive indices of the waveguide propagation modes were measured by using a prism-coupling method. It was found that the number of the propagation modes is dependent on the doses for the waveguides in Nd:YVO₄. The atom displacement in the near-surface region (about 2 μm beneath the surface) of the Nd:YVO₄ crystal induced by the implantation was simulated by using the TRIM 98 (transport and range of ions in matter) code. The possible reasons for the waveguide formation are discussed in a primary way. Received: 17 July 2002 / Revised version: 20 September 2002 / Published online: 11 December 2002 RID="*" ID="*"Corresponding author. Fax: +86-531-8565167, E-mail: drfchen@sdu.edu.cn     

1×4光子晶体波导分束器的特性

在完整的二维光子晶体中引入线缺陷,形成了光子晶体波导,光子晶体波导分束器是集成化光学电路的重要组成元件。我们设计了一种线缺陷1×4光子晶体分束器,并且用有限时域差分法研究了它的特性。研究表明,输出端的透射传输特性与入射光的波长和分支的几何形状有关,并且入射波分别相等地流入四个输出端口。为了减少1×4分束器在三个Y型分支区的反射,可以通过调节在分支区的可调介质柱的半径R,使每个输出端口具有很高的透射率。     

Mechanism and process of fabricating fluorinated polyimide optical waveguide by CO2 laser direct-writing

Fluorinated polyimide waveguides were fabricated by CO₂ laser direct-writing. The poly(amic acid) micro-region irradiated by CO₂ laser beam was studied with FT-IR micro-spectroscopy. The FT-IR spectra implied that the laser induced thermal-imidized polyimide was of optical anisotropy, and the imidization degree of exposed micro-region increased with the rising of output laser power. The increased aspect ratio of waveguide and smoothness of surface can be achieved by increasing the pre-cured temperature (below 120°C) and writing speed, and optimizing laser power and the distance between the lens and the annular aperture. The guided light was clearly confined to the core of the fabricated waveguide, which means this technique can be used for fluorinated polyimide waveguide fabrication.     

A linear-operator formalism for bianisotropic waveguides

A bianisotropic waveguide can be defined as a cylindrical waveguide filled with bianisotropic materials, and all the conventional waveguides are special cases of the bianisotropic waveguide. In this paper, guided wave propagation in bianisotropic waveguide is analyzed by the theory of linear operators, and two types of adjoint waveguides and inner products are introduced respectively. Based on the concept of adjoint waveguides, the functional expressions of the field equations can be obtained, and from which the eigenvalue problem of the bianisotropic waveguide can be solved. Also, bi-orthogonality relations of guided modes are derived. These biorthogonality relations reported here can be used to expand electromagnetic fields in terms of a complete set of modes in straight bianisotropic waveguide. As an example of application, mode matching formulae for a discontinuity problem are given.     

Calculation of the spectral response of an arrayed-waveguide gating demultiplexer with a wide-angle beam propagation method in a cylindrical coordinate system

The spectral response of an arrayed-waveguide grating (AWG) demultiplexer is calculated by simulating the field propagation in the output section of an AWG with a wide-angle beam propagation method (BPM) in a cylindrical coordinate system. As in a practical design of an AWG demultiplexer, each output waveguide consists of two straight sections connected by a bending section. The spectral response obtained by the present algorithm is more accurate than those obtained with two popular approximate methods, namely, the conventional overlapped integral method and the standard BPM for radially straight and infinitely long output waveguides. With the present algorithm, the dependence of the spectral response on the parameters of the output section is analyzed. The channel crosstalk and the 3 dB passband width of the spectral response depend mainly on the length of the first straight section, the end separation and the angular separation of the output waveguides. The bending section results in an asymmetrical spectral response with remarkable sidelobes which can be reduced by increasing the bending radius.     

A novel wavelength dispersive device with a dispersive element based on staircase-like straight and parallel arrayed waveguides

We propose a new type of arrayed waveguide grating (AWG) multiplexer/demultiplexer based on modified group refractive index. This device is composed by an array of straight and parallel waveguides of equal length and each waveguide consist of two sections with different width. The length of the two sections are changed from a waveguide to the adjacent one following a linear dependence resulting in a wavelength dispersive waveguide array. An example of the device design for silicon-on-insulator (SOI) platform is provided and numerical simulations have been carried out for various arrayed waveguide parameters. We demonstrate that the group index modification can be used for tailoring device dispersion properties, and that it can also result in new dispersion characteristics predicted numerically not observed in conventional AWGs. Additional advantages are that the demultiplexer does not necessarily require bending waveguide sections as in a conventional AWG (de)multiplexers, and thus yields highly compact devices with potentially very low insertion loss. Channel spacing of 1 nm have been predicted for sub-micron waveguides sizes. In this paper it is also proposed a novel wavefront converter based on waveguide array lens-like element with waveguides broadened sections. Numerical results for different input/output geometries are analized.     

基于波导间能量耦合效应的光子晶体频段选择与能量分束器

基于波导间能量耦合效应的光子晶体功率分束器具有结构紧凑、带宽较宽、弯曲损耗低、分光角度大和不受外界电磁场干扰等优点.本文利用时域有限差分方法,理论研究了二维三角晶格光子晶体耦合波导的功率分束特性,设计得出了一种能够在宽频谱范围内针对不同频率区间实现不同分光比的功能器件.在此基础上通过改变耦合区介质柱形状以及输出分支波导与能量耦合波导的连接位置,最终针对三个相邻频率范围内的入射光信号,较好地实现了三均分、二均分、单一输出通道这3种能量分配输出模式.该功能器件具有透过率对比度高、结构紧凑等特性,对于发展全光功能器件在大规模全光复杂集成领域内的实际应用具有一定的促进作用.