新型PES微孔材料的制备及性能研究

合成了新型双烯丙基聚醚砜(PES), 采用超临界CO2作为物理发泡试剂制备微孔材料, 研究了不同发泡温度、饱和压力、发泡时间和放气时间等因素对微孔形貌的影响. 结果表明, 发泡温度在110~170 ℃之间, 随着温度的升高, 泡孔直径增加, 泡孔密度在140 ℃达到一个最大值; 随着饱和压力的升高, 泡孔直径减小, 泡孔密度增大; 发泡时间和放气时间对微孔直径和密度影响不大; 研究了在不同辐照剂量下微孔材料的交联性能, 结果表明, 在600 kGy辐照剂量以下, 交联效果不明显, 在800 kGy以上, 随着辐照剂量的增大, 凝胶含量增加, 辐照后的样品在265 ℃热处理10 min, 仍能保持完好的微孔结构.     

水蒸气处理对HZSM-5分子筛催化剂的酸性及孔结构的影响

通过XRD，NH3-TPD，IR，比表面与孔结构测定等方法，研究了HZSM-5分子筛（硅铝比为38）在不同温度下进行水热处理时的酸性与孔结构。结果表明，随着水热处理温度的提高，HZSM-5分子筛的结晶度稍有增大；酸性明显减弱，弱酸位增多，强酸位相对减少；IR谱图上有一定的蓝移；比表面与微孔体积减小，介孔体积增大。     

酚醛树脂基球形微-介双阶多孔炭的软模板法制备

将苯酚和甲醛在碱性条件下聚合,然后在酸性条件下与软模板剂F127自组装形成中间相,经高温煅烧合成球形微-介双阶多孔炭。 通过扫描电子显微镜、透射电子显微镜、氮气吸附-脱附和热重分析技术对样品进行了形貌观察和性能测试。 结果表明,pH值、软模板剂用量和活化温度对样品形貌有调控作用。 当软模板剂F127的质量分数为20%、pH值为0.5和活化温度为700 ℃时,可制备出直径为100～200 nm的球形炭,球形粒子分散均匀,排列规整,呈明显蠕虫状排列的孔隙结构,比表面积为503 m2/g,孔容积0.416 cm3/g,介孔孔径集中分布在2.9 nm,微孔主要分布在1.3 nm。 随着活化温度升高,炭球的比表面积和孔容积增大,平均孔径减小。 F127的热解形成介孔结构,碳前驱体高温下的径向收缩形成微孔结构。     

碱处理脱硅与提高Y型分子筛硅铝比——矛盾的对立与统一

考察了 "水热处理"以及"碱处理+水热处理"两种方法所制得的超稳 Y 分子筛的骨架硅铝比、孔结构特征以及酸量, 并探讨了"碱处理+水热处理"方法对起始 NaY 分子筛的适应性. 结果表明, 在水热处理前, 对 NaY 分子筛进行碱处理脱硅可在不改变最终样品的骨架超稳化水平和酸量的同时, 样品的介孔体积显著增加. 直接水热处理 NaY 分子筛所得样品介孔体积不超过 0.14 cm3/g, 而先碱处理后水热处理, 所得样品介孔体积可达 0.22 cm3/g. 该法适用于制备骨架硅铝比高的 NaY 分子筛. 起始原料的骨架硅铝比较低时, 所得样品的介孔体积增幅小, 而且微孔受损严重.     

非表面活性剂合成CeO2介孔材料

以非表面活性剂三乙胺(TEA)和聚乙二醇(PEG)为模板剂,合成了具有立方莹石晶相结构的介孔CeO2材料,通过XRD,HRTEM,BET,FTIR和选区电子衍射(SAED)等手段对介孔CeO2进行了表征。考察了模板剂在CeO2介孔结构的形成过程中所起的作用及其对比表面、孔径分布、热稳定性的影响,并对模板剂的作用机制进行了分析。结果表明,三乙胺在CeO2介孔结构的形成中起关键作用,聚乙二醇对介孔结构热稳定性有明显的改善作用,经600℃焙烧3h的样品仍能保持较好的介孔结构,其介孔呈直通型的六方型孔道,比表面积>200m2·g-1,孔分布呈双孔型分布,其中介孔孔径约为5nm左右,微孔孔径在1～2nm之间,介孔占较大比例,并且微孔数量随焙烧温度的升高逐渐减少,直至600℃消失。     

新型孔结构渣油催化裂化催化剂

高温短接触FCC工艺和原料的重质化要求FCC催化剂具有大孔,以增加大分子烃在催化剂中的扩散速度,提高催化剂的反应性能。在不改变催化剂组成的前提下,采用聚苯乙烯微球为模板剂在催化剂基质中引入适量的、尺寸可控的大孔;通过SEM、N2吸附等对催化剂的形貌和孔结构进行了表征;以大庆常压渣油为原料,测定了催化剂的反应性能。实验表明,大孔催化剂中孔体积和比表面积随模板剂用量的增加而增加;在模板剂用量相同时,模板剂粒径越小孔体积和比表面积增加越多。模板剂的引入不仅增加了催化剂中的大孔孔体积,使得催化剂中微孔部分的体积和比表面积也有了一定增加。模板颗粒法合成的催化剂,扩散阻力小,重油转化率高,轻油收率高。     

介孔-微孔复合材料的水热稳定性及其催化裂化性能

采用无模板剂的溶胶凝胶法制备了一系列具有均一介孔和MFI沸石微孔的复合材料.与MCM-41相比,包含silicalite-1沸石结构的复合材料的水热稳定性得到显著改善.1,3,5-三异丙苯的催化裂化反应结果表明,与商品HZSM-5沸石相比,包含ZSM-5沸石结构的复合材料具有更高的催化活性和抗积炭性能.三异丙苯的转化率...     

以微孔β沸石为硅铝源合成强酸性介孔分子筛

以微孔β沸石为硅铝源,通过碱处理和以十六烷基三甲基溴化铵为模板剂,合成了具有较强酸性的六方结构介孔分子筛材料B-MCM-41,并采用XRD、N₂吸附脱附、FT-IR、²7Al MAS NMR、HRTEM和水热处理等手段对其进行了结构表征,采用NH₃-TPD对其进行了酸性表征。实验结果表明,B-MCM-41具有明显强于常规介孔分子筛的酸性,且在C⁺₁0混合芳烃加氢脱烷基化反应中表现出了良好的催化性能。这主要是由于碱溶液将β沸石降解为沸石结构单元,在表面活性剂作用下五元环次级结构单元被引入了介孔铝硅酸盐B-MCM-41的结构。     

模板剂对ZSM—5分子筛的成孔作用

用不同模板剂合成出不同硅铝比的ZSM-5沸石分子筛。在560℃赶除模板剂,经饱合吸冰后,应用多晶X射线衍射测定各样品的结晶度和晶胞体积。实验结果表明,合成氧化铝含量相同的ZSM-5分子筛时,加入不同的模板剂所得分子筛的晶胞体积不等(或称孔体积不等)。据此可以推测,模板剂对合成分子筛的造孔起支撑和定位的作用。     

硬模板法高温水热合成微孔-介孔二氧化硅及掺铝介孔二氧化硅

摘要 采用高温水热合成的方法有利于得到具备高水热稳定性的介孔二氧化硅.本研究中,我们利用α-亚麻酸在加热条件下通过胶束内聚合转化为能够耐受高温水热环境的介观模板,利用此硬模板在高温水热条件下直接合成了微孔-介孔二氧化硅及掺铝介孔二氧化硅.采用了不同的表征手段如X射线衍射（XRD）,氮气吸附,透射电镜等手段对材料进行了表征. 实验结果表明,制得的材料在沸水中处理5天后,仍能保持670m2 g-1的比表面积.透射电镜结果和NLDFT孔径分析结果显示,材料同时具备介孔和微孔结构.29Si MAS NMR谱图显示,完全缩聚的Q4型硅为材料中主要的硅组分,这解释了材料的高水热稳定性.     

The effect of hydrothermal treatment on column performance for monolithic silica capillary columns

Monolithic silica capillary columns with i.d. 100 μm and monolithic silica rods were prepared with tetramethoxysilane (TMOS) or a mixture of TMOS and metyltrimethoxysilane (MTMS) using different hydrothermal treatments at T=80 °C or 120 °C. Nitrogen physisorption was applied for the pore characterization of the rods and inverse size exclusion chromatography (ISEC) for that of the capillary columns. Using nitrogen physisorption, it was shown change of pore size and surface area corresponds to that of hydrothermal treatment and silica precursor. The results from ISEC agreed well with those from nitrogen physisorption regarding the pore size distribution (PSD). In addition, the retention factors for hexylbenzene with the ODS-modified capillary columns in methanol/water=80/20 at T=30 °C could also support the results from nitrogen physisorption. Furthermore, column efficiency for the columns was evaluated with alkylbenzenes and three kinds of peptides, leucine-enkephalin, angiotensin II, and insulin. Column efficiency for alkylbenzenes was similar independently of the hydrothermal treatment at T=120 °C. Even for TMOS columns, there was no significant difference in column efficiency for the peptides despite the difference in hydrothermal treatment. In contrast, for hybrid columns, it was possible to confirm the effect on hydrothermal treatment at T=120 °C resulting in a different column efficiency, especially for insulin. This difference supports the results from both nitrogen physisorption and ISEC, showing the presence of more small pores of ca. 3-6 nm for a hybrid silica without hydrothermal treatment at T=120 °C. Consequently, the results suggest that hydrothermal treatment for a hybrid column with higher temperature or longer time is necessary, compared to that for a TMOS column, to provide higher column efficiency with increase in molecular size of solute.     

以水热法合成的ZrO_2负载Au催化剂上的低温水煤气变换反应

采用一种简便的水热法合成了一系列ZrO2,并采用沉积-沉淀法制得相应1.0%Au/ZrO2催化剂,在模拟甲醇重整气气氛下评价了它们的低温水煤气变换(WGS)反应催化性能.结果发现,于150oC水热合成的ZrO2负载的Au催化剂活性最佳,240oC反应时CO转化率达87%,明显高于相同反应条件下Au负载量较高的Au/Fe2O3,Au/CeO2及Au/CeZrO4催化剂.采用X射线衍射、原子吸收光谱、N2物理吸脱附及扫描电子显微镜等手段对样品进行了表征.结果表明,Au/ZrO2催化剂的总孔体积及平均孔径越大、圆形片状形貌越规整,其低温WGS催化活性就越高.     

改善SBA-15介孔材料水热稳定性的简单溶剂热后处理方法

提出了一种有效改善SBA-15介孔材料水热稳定性的简单溶剂热后处理方法. SBA-15材料经环己烷、甲苯和正丁醇等有机溶剂在157和190 oC密闭容器中分别处理6–24 h后,可呈现很好的水热稳定性.它们在800 oC经100%水蒸气处理12 h,依然能保持很好的有序介孔结构,比表面积可高达192–281 m2/g.其中,经环己烷190 oC溶剂热处理24 h的样品表现出最优的水热稳定性.溶剂热处理能显著提升材料孔壁中类似Si(OSi)2(OH)2和Si(OSi)3OH结构的Si–OH基间脱水,形成稳定的Si(OSi)4结构,从而有效减少了SBA-15材料孔壁的缺陷.由此,介孔材料的水热稳定性得到明显改善.溶剂热处理对SBA-15材料水热稳定性的这种提升作用与所用溶剂性质、处理温度以及SBA-15前驱体的类型密切相关.其中,以低沸点的非极性溶剂处理焙烧后的SBA-15材料表现出最好的稳定化效果.该方法具有简单、低能耗的特点,其在制备高水热稳定的有序硅基介孔材料上有很好的潜在应用价值.     

A simple approach to prepare monodisperse mesoporous silica nanospheres with adjustable sizes

A new and facile approach has been developed to prepare monodisperse mesoporous silica nanospheres (MMSNs) with controlled particle sizes and pore structures. In our approach, MMSNs were synthesized simply in a sodium acetate solution without adding any other alkali or alcohol additives. MMSNs have a spherical shape and uniform particle sizes, which can be adjusted from 50 to 110 nm by increasing the reaction temperature from 40 to 80 °C. By performing a subsequent hydrothermal treatment (HT) under basic condition (pH=~11.5) at 130 °C, the mesoporous pore volume and surface area can be enhanced, while keeping the mono-dispersion characteristics and the mesopore size almost unchanged. The pore sizes of MMSNs can be adjusted from 2.8 to 4.0 nm under acidic solutions by changing the HT temperature from 100 to 130 °C. The formation process of MMSNs has been investigated by transmission electron microscopy (TEM) and attenuated total reflection Fourier transform infrared (ATR-FTIR) techniques. A spherical micelle templating mechanism is proposed to explain the formation of MMSNs in our system, which is different from that of traditional highly ordered mesoporous silica nanoparticles (MCM-41).     

Release of Terpenes from Fir Wood during Its Long-Term Use and in Thermal Treatment

Building structures made from fir wood are often attacked by wood-destroying insects for which the terpenes it contains serve as attractants. One of the possibilities for extending the lifetime of structures is to use older wood with a lower content of terpenes and/or thermally modified wood. The study evaluated the levels of terpenes in naturally aged fir wood (108, 146, 279, 287 and 390 years) and their decrease by thermal treatment (the temperature of 60 °C and 120 °C, treatment duration of 10 h). Terpenes were extracted from wood samples by hexane and?analyzed by gas-chromatography mass-spectrometry (GC-MS). The results indicate that recent fir wood contained approximately 60 times more terpenes than the oldest wood (186:3.1 mg/kg). The thermal wood treatment speeded up the release of terpenes. The temperature of 60 °C caused a loss in terpenes in the recent fir wood by 62%, the temperature of 120 °C even by >99%. After the treatment at the temperature of 60 °C the recent fir wood had approximately the same quantity of terpenes as non-thermally treated 108 year old wood, i.e., approximately 60-70 mg/kg. After the thermal treatment at the temperature of 120 °C the quantity of terpenes dropped in the recent as well as the old fir wood to minimum quantities (0.7-1.1 mg/kg). The thermal treatment can thus be used as a suitable method for the protection of fir wood from wood-destroying insects.     

Hybridization of sugar alcohols into brucite interlayers via a melt intercalation process

We report the preparation of organic-brucite (BR) hybrids using harmless sugar alcohols (xylitol, XYL, and sorbitol, SOR). Since XYL and SOR are solid materials at room temperature, the hybridization was investigated by comparing two separate methods, hydrothermal treatment and melt mixing. BR-sugar alcohol hybrids were successfully prepared by a melt intercalation method at 175 °C. X-ray diffraction and Fourier transform infrared spectroscopy analyses indicated that organic molecules were intercalated into the brucite layers, overcoming the barrier of hydroxyl bonds between the BR layers. Moreover, X-ray photoelectron spectroscopy and thermal analyses showed that the intercalated materials at 175 °C resulted in the formation of covalent Mg-O-C bond linkages on the interlayer surface of BR.     

Facile method to synthesize platelet SBA-15 silica with highly ordered large mesopores

Highly ordered mesoporous SBA-15 silica with large pore diameter of 18 nm (nominal BJH pore diameter ~22 nm) and short pore length (~500 nm) was synthesized using a micelle expander 1,3,5-triisopropylbenzene in the absence of ammonium fluoride by employing short initial stirring time at 17 °C followed by static aging at low temperature. Scanning and transmission electron microscopies revealed that the material comprised of platelet particles in which large mesopores were nearly flawlessly arranged within uniform domains up to 3 μm in size. The platelet SBA-15 had the (100) interplanar spacing of 17 nm, high surface area (~470 m(2) g(-1)) and large pore volume (~1.6 cm(3) g(-1)). The hydrothermal treatment at 130 °C for 2 days was employed to eliminate constrictions from the pore channels. The control experiment showed that a sample prepared with prolonged stirring had very similar mesoporous properties, but the particle size was smaller and the domains were irregular, proving that the static conditions facilitate the formation of SBA-15 with platelet particle morphology. The absence of ammonium fluoride was also critical in attaining the platelet particle shape.     

水热合成一锅法制备FePO4-SBA-15及其水热稳定性能

通过两种水热处理方式，即800 oC水汽条件和100 oC沸水处理，考察了一锅法制备的FePO4–SBA-15(OP)的水热稳定性.水热处理前后样品的结构变化通过小角X射线衍射和N2物理吸附表征.研究发现，经水热条件下原位生成FePO4修饰后的OP样品具有良好的水热稳定性，并且FePO4的担载量(5%和40%)对OP样品的水热稳定性几乎没有影响.这与文献报道的金属担载量会影响介孔材料水热稳定性的结果不同.此外，还对比研究了浸渍法制备的FePO4/SBA-15(IMP)和商品SBA-15的水热稳定性.结果表明，各样品水热稳定性由强到弱的顺序是OP>IMP>>SBA-15. OP和IMP样品水热稳定性优于纯硅分子筛SBA-15的原因可能是FePO4保护层能抑制介孔材料在水热环境下的结构塌陷. OP样品水热稳定性较IMP样品好的原因可能主要是由于OP样品中存在稳定的Si–O–Fe键和较多的微孔.     

α-Fe2O3的制备及其性能的研究

使用一定配比的乙酰丙酮,无水乙酸钠,三氯化铁合成的乙酰丙酮铁作为前驱体材料,采用水热法在不同温度条件下反应两小时合成α-Fe₂O₃,从而探寻光催化效率最佳反应条件。利用X-射线粉末衍射仪(XRD),场发射扫描电子显微镜(TEM),紫外可见漫反射光谱仪(UV-vis DRS),比表面积测试(BET),拉曼光谱(Raman spectra)等对材料进行表征分析。分析结果表明在同等情况下175°C下合成的α-Fe₂O₃还原六价铬的反应速率高于其他温度下合成的α-Fe₂O₃光催化速率。     

g-C_3N_4修饰β-ZnMoO_4光催化降解磺胺二甲嘧啶:合成方法的影响、降解动力学及机理(英文)

在过去几十年中,钼酸盐在功能材料领域的应用备受关注.例如,半导体材料二价金属钼酸盐MMoO_4(M=Ca,Mg,Zn)在发光、催化、电容器、闪烁探测器等方面已有良好的应用.研究表明,钼酸锌在紫外或可见光照射下能够有效降解甲基橙、维多利亚蓝、苯酚等污染物.中国拥有丰富的钼资源,目前钼主要用于生产高强度钢.制备钼基高效除污除材料可作为钼资源的另一种高附加值利用模式.氮化碳(g-C_3N_4)作为一种低成本的光活性改性剂,可提高半导体材料的光催化性能.迄今为止,基于氮化碳复合材料的制备方法包括:原位水热合成、超声波复合、一步升温合成和沉淀法等.然而,很少讨论合成方法对复合材料性能的影响.本文以β-ZnMoO_4为主体材料,g-C_3N_4为修饰材料,首次制备了两者复合的新型光催化剂.采用不同的方法和条件制备了β-ZnMoO_4和β-ZnMoO_4/C_3N_4复合材料,探讨了合成方法对复合材料光催化性能的影响,并进一步研究了材料光催化降解磺胺二甲嘧啶的动力学和降解途径.以钼酸钠和硝酸锌为原料,在不同温度和时间条件下,采用水热法合成得到了两种不同形貌的β-ZnMoO_4材料.光催化降解实验结果显示,水热合成条件对催化剂的光催化活性影响很大,280℃水热条件下维持24 h,得到表面光滑的不规则微米颗粒(β-ZnMoO_4-280),其光催化活性高于180℃条件下获得的片状形貌的钼酸锌材料(β-ZnMoO_4-180).β-ZnMoO_4/C_3N_4复合材料通过原位水热法和超声法合成,结果显示,原位水热合成条件下获得的β-ZnMoO_4-180/C_3N_4光催化剂对磺胺二甲嘧啶表现出显著增强的降解能力.相比之下,在280℃水热条件下,C_3N_4颗粒发生逐步分解,且反应开始时C_3N_4颗粒会扰乱β-ZnMoO_4-280晶体生长的连续性,使复合材料性能下降.对于超声法合成的β-ZnMoO_4/C_3N_4材料,两种β-ZnMoO_4/C_3N_4复合材料的光催化活性均提高,但提高程度不及水热法180℃条件下制备的材料.结果表明,对于光催化复合材料的制备,要选择适当的合成方法,才能得到高性能复合光催化材料,本文采用180℃的水热合成条件,添加3%g-C_3N_4,可得到性能最佳的β-ZnMoO_4-180/C_3N_4复合光催化剂.添加自由基抑制剂的光催化降解实验结果表明,超氧负离子(·O_2~–)和空穴(h~+)在降解中起主导作用.β-ZnMoO_4/C_3N_4复合材料光催化活性的增强归因于C_3N_4与β-ZnMoO_4之间形成异质结,该异质结提高了光生电子-空穴对的分离效率.通过液相-质谱联用手段,测定了磺胺二甲嘧啶降解的中间产物,结果表明,污染物的光催化降解途径主要包括脱氨基和脱甲基过程.