Determination of aflatoxin B1 in cereals by homogeneous liquid-liquid extraction coupled to high performance liquid chromatography-fluorescence detection

A simple and rapid method based on homogeneous liquid-liquid extraction coupled to HPLC with fluorescence detection was developed for the determination of aflatoxin B1 (AFB1) in the rice and grain samples after post-column derivatization. The proposed method eliminated the use of immunoaffinity columns for clean-up in the determination of AFB1. The parameters affecting recovery and preconcentration such as type and volume of organic solvent, volume ratio of water/methanol, concentration of phase separator reagent and extraction time were optimized. Under the optimized conditions, the calibration graph was linear in the concentration range of 0.01-1.0 ng/g with the detection limit of 0.003 ng/g. This method was successfully applied for the analysis of AFB1 in different cereal samples.     

Determination of organophosphorous pesticides in the ppq range using a simple solid-phase extraction method combined with dispersive liquid-liquid microextraction

Solid-phase extraction combined with dispersive liquid-liquid microextraction (SPE-DLLME) was applied for the extraction of six organophosphorous pesticides (OPPs) in water samples. The analytes considered in this study were determined by gas chromatography with mass spectrometry and included prophos, diazinon, chlorpyrifos methyl, methyl parathion, fenchlorphos and chlorpyrifos. Several extraction conditions (extraction solvent and elution/dispersion solvents nature, extraction solvent volume, elution solvent volume, water volume and sample volume) were tested for SPE-DLLME with these analytes and the best results were obtained using carbon tetrachloride as the extraction solvent and acetone as the elution/dispersion solvent. Calibration curves for the determination of OPPs in water samples were constructed in the concentration range of 10-100 ng/L. Limits of detection (LODs) ranged from 38 to 230 pg/L values that are below the maximum admissible level for drinking water (100 ng/L). Relative standard deviations (RSD) were between 8.6 and 10.4% for a fortification level of 100 ng/L. At the same fortification level, the relative recoveries (R.R.) of tap, well and irrigation water samples were in the range of 30.2-97.1%.     

Chromium speciation using an automated liquid handling system with inductively coupled plasma - mass spectrometric detection

The speciation of inorganic chromium in environmental samples is required for accurate assessment of pollution levels. Of the two chromium oxidation states, Cr (VI) is a known carcinogen, while Cr (III) is an essential element. Total chromium measurement cannot be used to determine actual environmental impact due to the considerable difference in toxicity of the two elemental forms. An automated liquid handling system, the PrepLab™, can be used with an inductively coupled plasma-mass spectrometer (ICP-MS) to quantify Cr (III) and Cr (VI) in liquid samples. An autosampler is used to introduce discrete sample volumes into a solid-phase chelation resin column. The Cr (III) and Cr (VI) species are separated and are introduced on-line into the VG PlasmaQuad 3 ICP-MS for detection. The chromatographic data are collected in time resolved analysis mode with the capability of simultaneous multiple-isotopic detection.     

Determination of bisphenol A (BPA) in the presence of phenol by first-derivative fluorescence following micro liquid-liquid extraction (MLLE)

Bisphenol A (BPA) in the presence of phenol is determined using a method based on first-derivative spectrofluorimetry. The proposed method involves a micro liquid–liquid extraction of sodium chloride saturated water samples with diethyl ether followed by direct fluorimetric analysis of extracts. The excitation spectra of both compounds in diethyl ether are recorded between 200 and 290 nm, with the emission wavelength at 306 nm. The first-derivative spectra were calculated, measuring the analytical signal for BPA at 239 nm. The concentration range over which the method was applied was 0.5–10.0 μg·l⁻¹ of BPA with relative standard deviations of 2.9% for a concentration of 4.0 μg·l⁻¹ of BPA. The detection limit was 0.07 μg·l⁻¹. The proposed method was applied satisfactorily to the determination of BPA in synthetic mixtures and water samples from different sources previously spiked with different amounts of these chemicals. Recovery values ranging from 93% to 112% were obtained for water samples.     

Assessment of matrix effects and determination of niacin in human plasma using liquid-liquid extraction and liquid chromatography-tandem mass spectrometry

A simple, sensitive and rapid liquid-liquid extraction method for the analysis of nicotinic acid (niacin) and its labeled internal standard nicotinic acid-d4 (niacin-d4) in human plasma was developed and validated. The analyte and its internal standard were isolated from acidified plasma using a single liquid-liquid extraction procedure with methyl-t-butyl ether. The extracted samples were analyzed by liquid chromatography-tandem mass spectrometry in positive electrospray ionization mode with multiple reaction monitoring. The calibration curves were linear in the measured range between 5 and 1000 ng/mL and the limit of detection was calculated as 122 pg/mL. The method required 250 microL of human plasma and the total run time between injections was 3.5 min. Matrix effects were assessed by post-column infusion experiments, phospholipids monitoring and post-extraction addition experiments. The extraction of phospholipids and niacin from plasma was studied under acidic, neutral and basic conditions. Acidic conditions were optimal for both the recovery of niacin and the removal of phospholipids; the degree of matrix effects for niacin was determined to be 2.5%. It was concluded that effective removal of matrix components can overcome low recovery issues associated with liquid-liquid extractions of polar analytes.     

Analysis of abuse drugs in urine using surfactant-assisted dispersive liquid-liquid microextraction

The process of surfactant-assisted dispersive liquid-liquid microextraction (SA-DLLME) followed by high-performance liquid chromatography-UV detection was successfully applied for the extraction and determination of selected cannabinoids (cannabidiol, Δ(9)-tetrahydrocannabinol, and cannabinol) in urine samples. The effective parameters on the extraction efficiency were studied and optimized utilizing two different optimization methods: one variable at a time (OVAT) and face center design (FCD). Under the optimum conditions (extraction solvent and its volume, toluene, 85 μL; disperser agent and its concentration, 1.0 mL of ultra-pure water containing 0.5 mmol/L tetradecyl tremethyl ammonium bromide (TTAB); sample pH, 2.0 and salt concentration, 11% w/v NaCl), the limits of detection of the method were in the range of 0.1-0.5 μg/L and the repeatability and reproducibility of the proposed method, expressed as relative deviation, varied between 4.1 and 8.5% and 6.7 and 11.6%, respectively. Linearity was found to be in the range of 1.0-200 μg/L and under the optimum conditions, the preconcentration factors (PFs) were between 190 and 292. This proposed method was successfully applied in the analysis of three male advocate urine samples and good recoveries were obtained.     

Characterization of N-palmitoylated human growth hormone by in situ liquid-liquid extraction and MALDI tandem mass spectrometry

Acylation is a common post-translational modification found in secreted proteins and membrane-associated proteins, including signal transducing and regulatory proteins. Acylation is also explored in the pharmaceutical and biotechnology industry to increase the stability and lifetime of protein-based products. The presence of acyl moieties in proteins and peptides affects the physico-chemical properties of these species, thereby modulating protein stability, function, localization and molecular interactions. Characterization of protein acylation is a challenging analytical task, which includes the precise definition of the acylation sites in proteins and determination of the identity and molecular heterogeneity of the acyl moiety at each individual site. In this study, we generated a chemically modified human growth hormone (hGH) by incorporation of a palmitoyl moiety on the N(epsilon) group of a lysine residue. Monoacylation of the hGH protein was confirmed by determination of the intact molecular weight by mass spectrometry. Detailed analysis of protein acylation was achieved by analysis of peptides derived from hGH by protease treatment. However, peptide mass mapping by MALDI MS using trypsin and AspN proteases and standard sample preparation methods did not reveal any palmitoylated peptides. In contrast, in situ liquid-liquid extraction (LLE) performed directly on the MALDI MS metal target enabled detection of acylated peptide candidates by MALDI MS and demonstrated that hGH was N-palmitoylated at multiple lysine residues. MALDI MS and MS/MS analysis of the modified peptides mapped the N-palmitoylation sites to Lys158, Lys172 and Lys140 or Lys145. This study demonstrates the utility of LLE/MALDI MS/MS for mapping and characterization of acylation sites in proteins and peptides and the importance of optimizing sample preparation methods for mass spectrometry-based determination of substoichiometric, multi-site protein modifications.     

Dispersive liquid-liquid microextraction combined with gas chromatography for extraction and determination of class 1 residual solvents in pharmaceuticals

The present study reports a new method for analyzing class 1 residual solvents (RSs), 1,1-dichloroethene (1,1-DCE), 1,2-dichloroethane (1,2-DCE), 1,1,1-trichloroethane (1,1,1-TCE), carbon tetrachloride (CT), and benzene (Bz), in pharmaceutical products using dispersive liquid-liquid microextraction (DLLME) combined with gas chromatography-flame ionization detection (GC-FID). Unlike common DLLME methods, solvents of high boiling point were selected as dispersive and extraction solvents in order to prevent their chromatographic peaks from overlapping with those of analytes that have short retention times. Therefore N,N-dimethyl formamide (DMF) and 1,2-dibromoethane (1,2-DBE) were chosen as dispersive and extraction solvents, respectively. Analytical parameters of the proposed method were determined and good linearities and broad linear ranges (LRs) were obtained. Taking 500 mg samples, limit of detections for the tested pharmaceuticals were obtained as 0.11, 0.03, 0.05, 0.05, and 0.006 μg g(-1) for CT, 1,1-DCE, 1,2-DCE, 1,1,1-TCE, and Bz, respectively, which are considerably much lower than their permissible limits in pharmaceuticals.     

Dispersive solid-phase extraction combined with dispersive liquid-liquid microextraction for the determination of polybrominated diphenyl ethers in plastic bottled beverage by GC-MS

A simple, inexpensive and reliable analytical method was developed for the determination of polybrominated diphenyl ethers (PBDEs) in polyethylene terephthalate (PET) bottled beverage using GC‐MS. The sample pretreatment using dispersive solid‐phase extraction (DSPE) for removing matrix and dispersive liquid–liquid microextraction (DLLME) for enriching analytes was performed. For the DSPE, different sorbents such as primary amine, secondary amine, C₁₈ and graphitized carbon black were tested for different sample matrices. By means of DSPE, 60–89% of the sample matrices could be removed. Acetonitrile solution obtained by DSPE cleanup was directly used as the dispersant for the subsequent DLLME, which made the combination of the DSPE with the DLLME much more straightforward. Under the optimal conditions, the enrichment factors (EFs) of PBDEs ranged from 199 to 292. Using matrix‐matched calibration, correlation coefficients above 0.994 were found and LODs ranged from 0.0023 to 0.15 μg/L. The recoveries were between 80 and 117% for beverages spiked at three different concentrations (1.0, 5.0 and 10 μg/L) with RSDs ranging from 3.7 to 14.7% (n=5). The results indicated that the combination of DSPE with DLLME was a powerful sample preparation tool for analysis of ultratrace analytes in complicated matrices.     

Determination of insecticides in water using in situ halide exchange reaction-assisted ionic liquid dispersive liquid-liquid microextraction followed by high-performance liquid chromatography

A dispersive liquid-liquid microextraction (DLLME) method using in situ halide exchange reaction to form ionic liquid (IL) extraction phase was developed to determine four insecticides (i.e. methoxyfenozide, tetrachlorvinphos, thiamethoxam, and diafenthiuron) in water samples. The preconcentration procedure, followed by high-performance liquid chromatography and variable wavelength detectors (VWD), enabled the formation of the immiscible IL extraction phase; the insecticides were transferred into the IL phase simultaneously, which enhanced the efficiency and sufficiency, greatly shortening the operation time. The experimental parameters affecting the extraction efficiency including volume of extraction IL, extraction and centrifugation times, volume of the sample solution and exchanging reagent, and addition of organic solvent and salt were investigated and optimized. Under optimized conditions, the extractions yielded recoveries of the target analytes from 82 to 102%. The calibration curves were linear, and the correlation coefficient ranged from 0.9990 to 0.9999 under the concentration levels of 5-200 μg/L. The relative standard deviation (n=6) was 2.9-4.6%. The limits of detection (LODs) for the four insecticides were between 0.98 and 2.54 μg/L.     

Tandem use of solid-phase extraction and dispersive liquid-liquid microextraction for the determination of mononitrotoluenes in aquatic environment

Solid‐phase extraction (SPE) in tandem with dispersive liquid–liquid microextraction (DLLME) has been developed for the determination of mononitrotoluenes (MNTs) in several aquatic samples using gas chromatography‐flame ionization (GC‐FID) detection system. In the hyphenated SPE‐DLLME, initially MNTs were extracted from a large volume of aqueous samples (100 mL) into a 500‐mg octadecyl silane (C₁₈) sorbent. After the elution of analytes from the sorbent with acetonitrile, the obtained solution was put under the DLLME procedure, so that the extra preconcentration factors could be achieved. The parameters influencing the extraction efficiency such as breakthrough volume, type and volume of the elution solvent (disperser solvent) and extracting solvent, as well as the salt addition, were studied and optimized. The calibration curves were linear in the range of 0.5–500 μg/L and the limit of detection for all analytes was found to be 0.2 μg/L. The relative standard deviations (for 0.75 μg/L of MNTs) without internal standard varied from 2.0 to 6.4% (n=5). The relative recoveries of the well, river and sea water samples, spiked at the concentration level of 0.75 μg/L of the analytes, were in the range of 85–118%.     

Improved solvent collection system for a dispersive liquid-liquid microextraction of organochlorine pesticides from water using low-density organic solvent

In this study, the organochlorine pesticides (OCPs) levels in lake and tap water samples were determined by a dispersive liquid-liquid microextraction method using a low-density organic solvent and an improved solvent collection system (DLLME-ISCS). This method used a very small volume of a solvent of low toxicity (11 μL of 1-nonanol and 400 μL of methanol) to extract OCPs from 10 mL water samples prior to the analysis by GC. After centrifugation in the dispersive liquid-liquid microextraction, there was a liquid organic drop floating between the water surface and the glass wall of the centrifuge tube. The liquid organic drop (with some water phase) was transferred into a microtube (3 mm×15 mm) with a syringe. The organic and aqueous phases were separated in the microtube immediately. Then, 1 μL of the organic solvent (which was in the upper portion of liquid in the microtube) was easily collected by a syringe and injected into the GC-ECD system for the analysis. Under optimum conditions, the linear range of this method was 5-5000 ng/L for most of the analytes. The correlation coefficient was higher than 0.997. Enrichment factors ranged from 1309 to 3629. The relative recoveries ranged from 73 to 119% for lake water samples. The LODs of the method ranged from 0.7 to 9.4 ng/L. The precision of the method ranged from 1.0 to 10.8% for lake water.     

Quantitation of antioxidants in water samples using ionic liquid dispersive liquid-liquid microextraction followed by high-performance liquid chromatography-ultraviolet detection

A simple and efficient method, ionic liquid-based dispersive liquid-liquid microextraction combined with high-performance liquid chromatography-ultraviolet detection (HPLC-UV), has been applied for the extraction and determination of some antioxidants (Irganox 1010, Irganox 1076 and Irgafos 168) in water samples. The microextraction efficiency factors were investigated and optimized: 1-hexyl-3-methylimidazolium hexafluorophosphate [C(6)MIM][PF(6)] (0.06 g) as extracting solvent, methanol (0.5 mL) as disperser solvent without salt addition. Under the selected conditions, enrichment factors up to 48-fold, limits of detection (LODs) of 5.0-10.0 ng/mL and dynamic linear ranges of 25-1500 ng/mL were obtained. A reasonable repeatability (RSD≤11.8%, n=5) with satisfactory linearity (r(2)≥0.9954) of the results illustrated a good performance of the presented method. The accuracy of the method was tested by the relative recovery experiments on spiked samples, with results ranging from 85 to 118%. Finally, the method was successfully applied for determination of the analytes in several real water samples.     

Determination of rifaximin in rat serum by ionic liquid based dispersive liquid-liquid microextraction combined with RP-HPLC

An efficient and environmental friendly ionic liquid based dispersive liquid-liquid microextraction procedure was optimized for determination of rifaximin in rat serum by reverse phase high-performance liquid chromatography. The effect of ionic liquids, dispersive solvents, extractant/disperser ratio, and salt concentrations on sample recovery and enrichment factors were studied. Among the five ionic liquids studied in the present investigation, 1-butyl-3-methylimidazolium hexafluorophosphate was found to be most effective for extraction of rifaximin. The recovery was found to be more than 98% using 1-butyl-3-methylimidazolium hexafluorophosphate and methanol as extraction and dispersive solvents, at an extractant/disperser ratio of 0.43. The recovery was further enhanced to 99.5% by the addition of 5.0% NaCl solution. A threefold enhancement in detection limit was achieved when compared to protein precipitation. The ionic liquid containing the extracted rifaximin was directly injected into HPLC system. The linear relationship was observed in the range of 0.03-10.0 μg/mL with the correlation coefficient (r(2) ) 0.9998. Limits of detection and quantification were found to be 0.01 and 0.03 μg/mL, respectively. The relative standard deviation was 2.5%. The method was validated and applied to study pharmacokinetics of rifaxmin in rat serum.     

Comparison of dispersive liquid-liquid microextraction based on organic solvent and ionic liquid combined with high-performance liquid chromatography for the analysis of emodin and its metabolites in urine samples

In this paper, two methods based on organic solvent dispersive liquid-liquid microextraction (OS-DLLME) and ionic liquid dispersive liquid-liquid microextraction (IL-DLLME) coupled with high-performance liquid chromatography have been critically compared for analyzing emodin and its metabolites (aloe-emodin, anthraquinone-2-carboxylic acid, rhein, danthron, chrysophanol and physcion) in urine samples. Several important parameters influencing the extraction recoveries of DLLME were carefully optimized. Under optimal conditions, the enrichment factors (EFs) for emodin and its metabolites by OS-DLLME and IL-DLLME were within the range of 90-295 and 63-192 respectively; the relative standard deviations (RSDs, n=3) for intra-day and inter-day precision were lower than 7.2 and 8.7% by OS-DLLME, and lower than 5.7 and 6.4% by IL-DLLME; the recoveries of emodin and its metabolites were from 87.1 to 105% for OS-DLLME and from 94.8 to 103% for IL-DLLME, respectively. There were no significant deviations between the two methods for the determination of emodin and its metabolites. From the results of HPLC/UV of urine sample after DLLME, the metabolites aloe-emodin, rhein, chrysophanol and physcion were identified by comparing the retention times with the standards. From the results of HPLC/MS, anthraquinone-2-carboxylic acid and danthron as unreported metabolites of emodin were found.     

Determination of beta-lactam antibiotics in milk using micro-flow chemiluminescence system with on-line solid phase extraction

In this paper, a chemiluminescence (CL) micro-flow system combined with on-line solid phase extraction (SPE) is presented for determination of β-lactam antibiotics (penicillin, cefradine, cefadroxil, cefalexin) in milk. It is based on the enhancement effect of β-lactam antibiotics on the luminol-K₃Fe(CN)₆ CL system. The micro-flow system was fabricated from two polymethyl methacrylate (PMMA) plates (50 mm × 40 mm × 5 mm) with the microchannels of 200 μm wide and 150 μm deep. C₁₈-modified silica gel was packed into the microchannel (length: 10 mm; width: 1 mm; depth: 500 μm) to serve as SPE device. Extraction and preconcentration of the analytes were carried out using on-line SPE micro-flow system and the selectivity of CL detection was improved. The detection limits were 0.5 μg mL⁻¹ of penicillin, 0.04 μg mL⁻¹ of cefradine, 0.08 μg mL⁻¹ of cefadroxil and 0.1 μg mL⁻¹ of cefalexin. The proposed method was also applied to analyze the β-lactam antibiotics in milk. Experimental results were in good agreement with those obtained by high performance liquid chromatography (HPLC) method with UV detection.     

Simple, rapid, and sensitive determination of beta-blockers in environmental water using dispersive liquid-liquid microextraction followed by liquid chromatography with fluorescence detection

A novel method, dispersive liquid-liquid microextraction combined with liquid chromatography-fluorescence detection is proposed for the determination of three beta-blockers (metoprolol, bisoprolol, and betaxolol) in ground water, river water, and bottled mineral water. Some important parameters, such as the kind and volume of extraction and dispersive solvents, extraction time, pH, and salt effect were investigated and optimized. In the method, a suitable mixture of extraction solvent (60 μL carbon tetrachloride) and dispersive solvent (1 mL acetonitrile) were injected into the aqueous samples (5.00 mL) and the cloudy solution was observed. After centrifugation, the enriched analytes in the bottom CCl(4) phase were determined by liquid chromatography with fluorescence detection. Under the optimum conditions, the enrichment factors (EFs) for metoprolol, bisoprolol, and betaxolol were 180, 190, and 182, and the limits of detection (LODs) were 1.8, 1.4, and 1.0 ng L(-1) , respectively. A good linear relationship between the peak area and the concentration of analytes was obtained in the range of 3-150 ng L(-1) . The relative standard deviations (RSDs) for the extraction of 10 ng L(-1) of beta-blockers were in the range of 4.6-5.7% (n = 5). Compared with other methods, dispersive liquid-liquid microextraction is a very simple, rapid, sensitive (low limit of detection), and economical (only 1.06 mL volume of organic solvent) method, which is in compliance with the requirements of green analytical methodologies.     

固相萃取-超高效液相色谱-电喷雾串联质谱法测定调味品中的罗丹明B

利用超高效液相色谱-电喷雾串联质谱(UPLC-MS/MS)方法测定了调味品中罗丹明B。样品经乙腈-乙酸水溶液提取后,经固相萃取(SPE)柱净化,采用BEH C18柱分离,以乙腈和0.2%的甲酸水溶液为流动相进行梯度洗脱,采用正离子、多反应监测(MRM)模式进行定性定量测定。罗丹明B在0.5～500μg/L质量浓度范围内线性关系良好,相关系数r为0.999,检出限、定量限分别为0.03,0.10μg/kg;平均回收率为86.6%～95.7%,标准偏差小于10%。方法适用于调味品中罗丹明B的测定。     

Dispersive liquid-liquid microextraction coupled with high-performance liquid chromatography-diode array detection for the determination of N-methyl carbamate pesticides in vegetables

This paper described a simple, rapid and efficient method for the determination of N-methyl carbamate pesticides in tomato, cucumber, carrot and lettuce samples by dispersive liquid-liquid microextraction coupled with HPLC-diode array detection. Some experimental parameters that influenced the extraction efficiency, such as types and volumes of extraction and disperser solvents, extraction time and salt effect were examined and optimized. Under optimum conditions, the LOD of the method were 0.5-3.0 μg/kg depending on the compounds and the kind of vegetables. The linearities of the method were obtained in the range of 10.0-300 μg/kg for aldicarb, MTMC, carbofuran and carbaryl, and 20.0-600 μg/kg for isoprocarb, with the correlation coefficients ranging from 0.9921 to 0.9993. The RSD varied from 2.9 to 7.5% (n=5). The recoveries of the method for the five carbamates from vegetable samples at two different spiking levels were ranged from 77.8 to 98.2%. Results showed that the method we proposed can meet the requirements for the determination of N-methyl carbamate in vegetable samples and was finally applied to the analysis of target pesticides in vegetable samples taken from local markets.     

Application of dispersive liquid-liquid microextraction combined with high-performance liquid chromatography for the determination of methomyl in natural waters

A new method was developed for determination of methomyl in water samples by combining a dispersive liquid-liquid microextraction (DLLME) technique with HPLC-variable wavelength detection (VWD). In this extraction method, 0.50 mL of methanol (as dispersive solvent) containing 20.0 microL of tetrachloroethane (as extraction solvent) was rapidly injected by syringe into a 5.00-mL water sample containing the analyte, thereby forming a cloudy solution. After phase separation by centrifugation for 2 min at 4000 rpm, the enriched analyte in the settled phase (8 +/- 0.2 microL) was at the bottom of the conical test tube. A 5.0-microL volume of the settled phase was analyzed by HPLC-VWD. Parameters such as the nature and volume of the extraction solvent and the dispersive solvent, extraction time, and the salt concentration were optimized. Under the optimum conditions, the enrichment factor could reach 70.7 for a 5.00-mL water sample and the linear range, detection limit (S/N = 3), and precision (RSD, n = 6) were 3-5000 ng/mL, 1.0 ng/mL, and 2.6%, respectively. River and lake water samples were successfully analyzed by the proposed method. Comparison of this method with solid-phase extraction, solid-phase microextraction, and single-drop microextraction, indicates that DLLME combined with HPLC-VWD is a simple, fast, and low-cost method for the determination of methomyl, and thus has tremendous potential in trace analysis of methomyl in natural waters.