力化学降解对聚氮乙烯加工流变行为的影响

采用Ｂｒａｂｅｎｄｅｒ塑化仪和毛细管流变仪研究了经力化学降解制得的聚氯乙烯（ＰＶＣ）的加工流变行为。结果表明，降解的ＰＶＣ塑化时间比未降解的ＰＶＣ明显缩短。塑化速度和熔化效率也明显加快，熔体粘度及玻璃化温度降低。     

十二烷基硫酸钠对聚乙烯醇亚浓水溶液流变行为的影响

表面活性剂会影响聚乙烯醇(PVA)分子间及分子内氢键形成,进而改变其水溶液的流变响应.本文在确定十二烷基硫酸钠(SDS)在PVA亚浓水溶液中的临界聚集浓度(CAC)和临界胶束浓度(CMCP)基础上,考察了SDS对PVA亚浓溶液(10 wt%)流变行为的影响.研究发现,不同浓度SDScsur对PVA水溶液稳态流变行为的影响差异较大:(1)当csur CMCP,随着csur增加,胶束起物理交联点作用,ηa增大,复合溶液的动态储能模量亦显著增大.加入SDS后,PVA体系内结合水的数目降低,但当csur> CMC后,结合水的数目几乎不变,黏流活化能也表现出相近的变化规律.与稀溶液相比,SDS对PVA亚浓溶液的降黏幅度较大.     

氯化聚氯乙烯/氯化聚乙烯共混体的流变性能

<正> 氯化聚氯乙烯(CPVC)是聚氯乙烯(PVC)的氯化产物。它具有优良的耐化学腐蚀、耐油、隔氧等性能。它的使用温度、抗张和弯曲强度与PVC相比有很大提高。这些特性加上氯元素资源丰富、价格便宜,使CPVC可望成为具有吸引力的热塑性工程塑料。有关CPVC共混体系的研究已有不少报道。然而多数的研究范围较窄,尤其是关于CPVC共混体系流变性研究很少见。本文首次广泛研究了不同组成的CPVC/CPE共混     

聚氯乙烯表皮成分对加成型硅橡胶固化的影响

采用流变学方法研究了双组分加成型硅橡胶在不同聚氯乙烯(PVC)表皮上的固化动力学,并利用红外光谱、核磁共振波谱、电感耦合等离子体质谱仪等手段分析了PVC表皮成分,以确定导致双组分加成型硅橡胶不固化的具体原因。 结果表明,PVC表皮中导致硅橡胶不固化的主要元素为P元素。 在固定硅橡胶厚度为1 mm的情况下,当PVC表皮中的P元素质量分数低于3×10^-3%时,浇注在其上的双组分加成型硅橡胶依然能固化;而当PVC表皮中的P元素质量分数超过约2.4×10^-2%时,虽然浇注在其上的双组分加成型硅橡胶的中间层依然能固化,但与PVC表皮接触部分的硅橡胶不固化,且不固化层厚度随P元素质量分数增加而增加。 本文还研究了在P元素质量分数低于3×10^-3%的PVC表皮上,降低硅橡胶厚度至微米级时的固化行为,在P元素质量分数低于3×10^-3%的PVC表皮上,当硅橡胶厚度低于2 μm时,硅橡胶出现不完全固化现象。 双组分加成型硅橡胶在含有P元素的PVC表皮表面的固化行为主要是由硅橡胶样品中铂催化剂总含量及PVC表皮中的P元素含量确定的,同时也会受到双组分加成型硅橡胶反应速率以及铂催化剂、P元素在硅橡胶中的扩散速率的影响。     

泥鳅体表黏液的流变行为

研究了无鳞鱼———泥鳅的体表黏液流变行为,发现黏液的稳态流动存在着3个不同区域:第一区域内,黏度随剪切速率(γ)变化不显著,呈现牛顿流动行为;第二区域内,随γ增大,黏度下降,呈现非牛顿行为;第三区域内,随γ继续增大,黏度又基本保持不变.黏液表观黏度(ηa)与γ的关系可用Carreau模型很好地拟合,其增比黏度(ηsp)与浓度(c)的关系为ηsp∝c1.5,表明黏液处于亚浓缠结区域.在测试频率(ω)范围内,黏液的动态储能模量(G′)大于动态损耗模量(G″),表明与黏性相比较,弹性占优,且G′及G″随ω变化不显著.存在一临界温度(35℃),当低于35℃时,黏液黏度随温度变化不显著,当高于35℃时,黏液变性,表现出不同的流变行为.     

表面活性剂对聚氯乙烯膜修饰电极电化学行为的影响

采用循环伏安法考察了所制备的聚氯乙烯(PVC)膜修饰电极的稳定性,结果表明,该修饰电极性能稳定,电极反应过程为扩散控制的过程。以循环伏安法、计时库仑法、稳态极化曲线法和交流阻抗法分别考察了阳离子(十六烷基三甲基溴化铵,CTMAB)、阴离子(十二烷基硫酸钠,SDS)和非离子(脂肪醇聚氧乙烯醚,AEO9)3种不同类型的表面活性剂对PVC膜-Ag[B(ph)4]修饰电极反应过程的影响。结果表明:加入CT-MAB或SDS后,PVC膜中Ag[B(ph)4]氧化态和还原态的扩散系数分别比电极在0.1mol/LKOH支持电解质中的扩散系数小,PVC膜修饰电极的反应过程受扩散控制的特征变得更明显,表明在此条件下膜中的电子转移速度加快,CTMAB或SDS对PVC膜修饰电极的电极反应过程有增敏作用。而加入AEO9后,PVC膜中的Ag[B(ph)4]氧化态和还原态的扩散系数比电极在0.1mol/LKOH支持电解质中的扩散系数大,并使电极反应的控制步骤从扩散控制转向含电子转移控制的扩散控制,表明在此条件下膜中的电子转移速度变慢,AEO9对PVC膜修饰电极的电极反应过程有抑制作用。     

界面改性剂对刚性粒子增韧尼龙6熔体流变行为的影响

研究了界面改性剂对高岭土增韧尼龙６熔体流变行为的影响,并与硅烷偶联剂ＫＨ５５０进行了比较．结果表明,ＫＨ５５０的加入明显降低了高岭土填充尼龙６熔体的粘度和弹性,而界面改性剂显著地增强了它的粘度和弹性．这一差别应归因于同ＫＨ５５０相比,界面改性剂更有效地增强了高岭土与尼龙６基体之间的界面结合和其自身的回弹性能．同时,界面改性剂的用量对高岭土填充尼龙６流变行为具有很大影响．当界面改性剂的用量为高岭土和尼龙６总量的２％时,界面改性剂在高岭土表面上趋于“饱和”,再增加界面改性剂的用量,对流变行为的影响不大．     

尼龙6/高岭土界面相互作用对其复合材料力学性能和流变行为的影响

<正> 无机填料填充复合材料的性能,除了依赖于聚合物基体和填料固有的内在性质外,很大程度上依赖于它们之间的界面性质。因此,研究聚合物/填料界面相互作用,对合理地设计具有优良性能的复合材料具有十分重要的意义。 目前,还很难对粉末填料与聚合物基体之间界面相互作用进行定量的研究,而且关于这方面的报道也较少。本文利用接触角法测定了高岭土填料和尼龙6基体的表面自由能、界面张力、粘附功等热力学参数,对高岭土与尼龙6之间界面相互作用与复合材料力学性能、流变行为的关系进行了分析和探讨。     

一维粒子对聚乙烯醇水溶液流变行为的调控

将一维粒子(碳纳米管, CNTs; 碳纳米纤维, CF)加入聚乙烯醇(PVA)水溶液中, 考察碳粒子表面含氧官能团含量(羟值)、 长径比、 温度及PVA本体溶液浓度等对复合体系流变行为的影响. 结果显示, 复合溶液的黏度(η)随CNTs用量({\phi }_{\mathrm{C}\mathrm{N}\mathrm{T}\mathrm{s}})先增大后降低, 然后继续增大, 呈“N”形变化趋势, 出现两个拐点({\phi }_{\mathrm{1}}和{\phi }_{\mathrm{2}}). 在{\phi }_{\mathrm{1}}附近, CNTs主要起物理交联点作用, 体系η增加; 在{\phi }_{\mathrm{2}}附近, CNTs对PVA分子间氢键作用破坏最为严重, 体系η低于纯PVA溶液, 表明不同羟值CNTs仅改变其用量即可使PVA水溶液增黏或降黏. 随着羟值增大, CNTs与PVA大分子间相互作用加强, {\phi }_{\mathrm{1}}和{\phi }_{\mathrm{2}}减小, {\phi }_{\mathrm{2}}对应的η下降, 降黏效果显著. CNTs的加入使PVA水合数下降, 羟值大的CNTs可与PVA上更多的羟基形成氢键作用, 水合数更低. 随着{\phi }_{\mathrm{C}\mathrm{N}\mathrm{T}\mathrm{s}}增大, 复合体系黏流活化能增大. CNTs对不同质量分数PVA水溶液的η具有类似的调控作用, 但调控幅度有差异. 相同羟值、 不同长径比的CNTs对PVA水溶液的黏度调控均呈“N”形变化, 长径比小的CNTs复合体系, {\phi }_{\mathrm{1}}和{\phi }_{\mathrm{2}}较大. 长径比相近但直径较大的CF复合体系表现出更低的{\phi }_{\mathrm{1}}和{\phi }_{\mathrm{2}}.     

可控交联聚醚醚酮动态流变学行为的研究

聚芳醚酮类材料因其优异的综合性能在许多领域得到广泛应用 [1,2 ] .许多研究者通过提高聚芳醚酮分子链的刚性度来实现进一步提高其使用温度 ,但由于其在高温时流动性下降 ,熔体粘度增大 ,给加工及应用带来很大困难[3] .基于此 ,我们将可在高温或辐照条件下发生交联反应的硫醚结构作为交联点引入到聚醚醚酮主链中 ,合成了可控交联的聚醚醚酮[4 ,5] .聚合物的分子结构及其熔体中分子的内部作用可以用流变学进行研究 .因此 ,我们用动态流变学实验监测跟踪聚合物的交联反应过程 ,研究可控交联聚醚醚酮的交联反应动力学 ,为设计改造分子结构以满…     

Effect of new melamine-terephthaldehyde resin modified graphene oxide on thermal and mechanical properties of PVC

In this study a new melamine-terephthaldehyde resin modified graphene oxide was synthesized and used as a reinforcement of poly(vinyl chloride) (PVC). Characterization, morphology, thermal and mechanical properties of the nanocomposites were examined by means of attenuated total reflectance-Fourier transform infrared spectroscopy, X-ray diffraction, field emission-scanning electron microscopy, thermogravimetric analysis, differential scanning calorimeter and tensile properties. The first hydrochloric acid releasing data of poly(vinyl chloride) was removed by incorporation of the modified graphene oxide as compare to the neat polymer. The temperatures at 2 wt% losses, main decomposition temperatures, maximum decomposition temperatures, also shift to higher temperature in the corresponding nanocomposites as compared to the neat PVC. The tensile strength and elongation at break of the nanocomposite films was increased as compared to the neat PVC. The interesting results in crystallinity of PVC were observed with adding 5 wt% of the modified graphene oxide.     

Structures and Mechanical Properties of PVC／Na^＋—Montmorillonite Nanocomposites

Poly(viyl chloride)/Na^ -montmorillonite(PVC/MMT)nanocomposites with different MMT contents were prepared via melt blending.Wide-angle X-ray diffraction(WAXD)and transmission electron microscopy(TEM)were used to characterize the structures.Effects of MMT content on the mechanical properties were also studied.It is found that PVC molecular chains can intercalate into the gallery of MMT layers during melt blending process,the stiffiness and toughness of the composites are inproved simultaneously within 0.5-7wt% MMT content,and the transparency and mechanical properties decrease as MMT conten further increases.     

Effect of Different Organic Modifiers on the Tensile Properties of PVC／EVA／Montmorillonite Composites

Poly (vinyl chloride)/ethylene-vinyl acetate/montmorillonite (PVC/EVA/OMMT) composites were prepared by melt blending method. Two kinds of montmorillonites were organically modified by trimethyloctadecyl ammonium and dimethyl bis (hydrogenated tallow) ammonium, respectively. The morphology and tensile properties of the resultant composites were discussed in terms of the modifier type and OMMT content. The PVC/EVA/OMMT composites have intercalated structure, which is independent of the polarity of the modifiers, while the tensile properties show strong dependence on the modifier type. The OMMT modified by polar modifier gives higher tensile ductile and strength of PVC/EVA/OMMT composites.     

Performance testing of a green plasticizer based on lactic acid for PVC

In order to develop alternative green plasticizers, a bio-based plasticizer, acetylated lactic acid 1,4-cyclohexanedimethyl ester(ALCH), with novel molecule geometry was synthesized from l-lactic acid and characterized by FTIR, ¹H NMR and matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOF-MS). The prepared ALCH was mixed with poly(vinyl chloride) (PVC) as plasticizer and the results indicated that the PVC films plasticized by ALCH have better migration and volatility stability than acetyl tributyl citrate (ATBC). In addition, ALCH could endow PVC products with excellent performance of strength, elongation and elasticity. With the substitution of ALCH for ATBC, glass transition temperature (Tg) of PVC films decreased gradually from 61.3°C to 55.0 °C. The self-polymerization of lactic acid gives ALCH better plasticizing effectiveness than ATBC.     

Al(OH)3和Mg(OH)2对PVC热解特性的影响研究

利用热重分析仪并借助电导率测定法探讨了Al(OH)3和Mg(OH)2对PVC热解特性的影响,简要分析了其机理。结果表明:加入Al(OH)3和Mg(OH)2后均能增加PVC体系在第一阶段的最大热解速率和残炭量,最大热解速率增加约1倍,残炭量增加约4倍。并且分解产生的结晶水吸收大量的热量,惰性金属氧化物也有利于成核、炭层生长和凝聚,有着明显的阻燃和抑烟作用。HCl毒性气体的释放主要集中在体系的第一阶段,Al(OH)3能促使HCl提前释放,HCl的释放总量增加,Mg(OH)2也能促使HCl提前释放,但HCl的释放总量却是减少的。     

采用流变学方法研究聚酰胺酸6FDA-TFDB溶液的降解行为

合成了一种聚酰胺酸6FDA-TFDB溶液,利用流变仪研究其在不同影响因素(如:温度、升温速率、溶剂含水量等)下的流变行为,发现聚酰胺酸溶液的降解在高温区和低温区存在不同的行为.通过Andrade公式获得不同条件下聚酰胺酸溶液的黏流活化能,并比较其差异,同时对溶剂水含量在不同温度区域下对聚酰胺酸降解速率的影响也进行了深入的分析,从而建立一种半定量比较不同条件下聚酰胺酸溶液降解速率的方法.     

Thermal degradation of PVC synthesized with a titanocene catalyst II. Complementary isothermal results

The use of an isothermal degradation method on metallocene produced PVC and commercial PVC, under nitrogen and air atmospheres, reveals more details about degradation routes. Without regard to the polymer origin, the hydrochloric acid release occurs in two steps, which are reflected in molecular weight only under a nitrogen atmosphere; otherwise, the oxygen appears to be included in the scission/crosslinking process. On the one hand, Met PVC has unsaturations from its synthesis, producing a faster HCl release compared to Com PVC; consequently, its degradation resistance is lower. On the other hand, Com PVC has more oxidized species and has a natural tendency to include more of them. Surface area seems to have an important effect and is directly related to the rate of hydrochloric acid release. The latter is not supported by the chain oxidation mechanism, making the effect of the applied atmosphere more critical to the results obtained from the degradation experiments.     

Hydroxylbenzylthioethers as novel organic thermal stabilizers for rigid PVC

An investigation was carried out on the performances of hydroxylbenzylthioethers employed as organic thermal stabilizers for rigid poly(vinyl chloride). The efficiency of these compounds as thermal stabilizers was evaluated by using Haake polydrive mixer and TGA. The stabilizing efficiency was compared with Ca-Zn soap and methyltin stabilizer. Hydroxylbenzylthioethers exhibit greater efficiency than both of these stabilizers. This is attributed to the ability of these compounds to prevent the formation of polyene sequences. The hydroxylbenzylthioethers-stabilized PVC showed a slightly lower glass transition temperature (T_g) in comparison with the original PVC. Hydroxylbenzylthioethers and epoxidized soybean oil (ESBO) exhibit synergistic effect on the stabilizing effect, when the mass ratios of ESBO to hydroxylbenzylthioethers are less than 0.5.