荧光光谱法研究纳米二氧化钛光催化降解核壳型CdSe/ZnS量子点

在光诱导条件下,利用纳米二氧化钛(P25)对荧光物质核壳型CdSe/ZnS量子点进行光催化降解实验,通过荧光光谱法与传统分光光度法对比研究,测定降解液的吸光度来进行分析与评价降解率,从而判断降解程度和效率.光催化降解结果表明:对荧光物质CdSe/ZnS量子点的荧光淬灭程度(F/F0)与反应时间(t)呈线性关系,符合CdSe/ZnS量子点光催化降解动力学拟合方程,证明了荧光光谱法与传统吸光光度检测结果的一致性.建立了一种高效灵敏检测光催化降解荧光物质方法,有助于分析荧光物质的光催化降解机理,为光催化降解其它荧光物质的相关研究提供参考.     

3-巯基丙酸修饰的CdSe/ZnS量子点的合成及测定牛血清白蛋白的研究

以3-巯基丙酸作为修饰剂,在水溶液中合成了稳定的CdSe/ZnS量子点(QDs),透射电镜观察所合成量子点的形貌近似球形,粒径约为25 nm.吸收光谱与荧光光谱的研究表明,CdSe QDs在410 nm处有最大吸收峰,而CdSe/ZnS QDs的最大吸收峰在470 nm处,CdSe/ZnS QDs的荧光强度是CdSe QDs的11倍.考察了缓冲溶液的体积、pH值、反应温度、反应时间对体系荧光的影响.在最佳实验条件下,体系的荧光强度与BSA的浓度呈线性关系,线性响应范围为0.746×10-7～4.48×10-7 mol/L,检出限为3.846×10-10 mol/L.并且CdSe/ZnS QDs荧光强度基本保持稳定,可达两个多月.该方法应用于合成样品的测定,结果满意.     

水溶性的CdSe/CdS/ZnS量子点的合成及表征

用L-半胱氨酸盐(Cys)作为稳定剂,合成了水溶性的双壳结构的CdSe/CdS/ZnS半导体量子点。吸收光谱和荧光光谱结果表明,双壳结构的CdSe/CdS/ZnS纳米微粒比单一的CdSe核纳米粒子和单核壳结构的CdSe/CdS纳米粒子具有更优异的发光特性。用透射电子显微镜(TEM)、ED、XRD、XPS和FTIR等方法对CdSe核和双壳层的CdSe/CdS/ZnS纳米微粒的结构、分散性及形貌分别进行了表征。     

基于CdSe/ZnS量子点构建乙酰甲胺磷荧光检测方法研究

本文以CdSe/ZnS量子点为荧光探针,基于乙酰甲胺磷对CdSe/ZnS量子点的荧光猝灭效应,建立了一种可快速测定乙酰甲胺磷的荧光检测方法。通过透射电子显微镜(TEM)、紫外-可见吸收光谱和荧光光谱对CdSe/ZnS量子点进行表征。在反应时间为5 min条件下,乙酰甲胺磷的浓度在0.487×10~(-6)～7.225×10~(-6) mol/L范围内与CdSe/ZnS量子点的荧光猝灭强度比值呈良好的线性关系(R~2=0.9987),方法检出限为2.55×10~(-7) mol/L。在2.0、5.0μmol/L加标水平下的回收率为94.5%～102.8%,相对标准偏差(RSD,n=5)小于4%。该方法选择性好,灵敏度高,可用于水果和蔬菜中农药乙酰甲胺磷的快速检测。     

基于CdSe/ZnS量子点构建多巴胺荧光检测方法的研究

以CdSe/ZnS量子点为荧光探针,基于多巴胺对CdSe/ZnS量子点的荧光猝灭效应,建立了一种可快速测定多巴胺的荧光检测方法。在最优实验条件下(pH7.4,反应时间20min),多巴胺浓度在0.01~0.7μmol/L范围内与CdSe/ZnS量子点的荧光猝灭强度比值呈良好的线性关系(r=0.996),方法检出限为1.6×10-4μmol/L,相对标准偏差为1.2%。与文献报道的方法相比,该方法的检出限更低,更为灵敏,可用于多巴胺注射液及人体尿样中多巴胺的快速检测。     

CdTe/CdS量子点的Ⅰ-Ⅱ型结构转变与荧光性质

制备了壳层厚度可以精确控制的CdTe/CdS核壳量子点, 利用紫外-可见吸收光谱、光致发光光谱、透射电镜和时间分辨光谱等技术, 分析了CdS壳层厚度对CdTe量子点的荧光量子产率和光谱结构的影响规律. 发现了不同于CdSe/CdS, CdSe/ZnS, CdTe/ZnS等核壳量子点的荧光峰展宽、大幅度红移以及荧光寿命大幅度增加现象. 根据能带的位置关系, 随着CdS厚度的增加, CdTe从Ⅰ型结构逐渐过渡到Ⅱ型核壳结构. 对于Ⅱ型CdTe/CdS核壳量子点, 不仅存在CdTe核区导带电子与价带空穴间的直接复合, 还存在CdS壳层导带电子与CdTe核价带空穴界面处的间接复合, 发光机制的变化导致荧光峰的展宽、明显红移和荧光寿命的增加. 当壳层过厚时, 壳层表面新引入的缺陷会阻碍荧光寿命和量子产率的进一步提高.     

CdSe/ZnS量子点探针用于检测猪链球菌2型溶菌酶释放蛋白(MRP)抗原的新方法研究

合成了高发光效率的CdSe/ZnS量子点并制备了CdSe/ZnS量子点-溶菌酶释放蛋白(MRP)抗体探针, 利用凝胶电泳和分子光谱法研究了MRP抗体与CdSe/ZnS量子点的结合机理. 荧光光谱法优化了CdSe/ZnS量子点-MRP抗体探针制备的影响因素, 建立了一种测定MRP抗原的新方法, 其线性范围为5.0×10－8～1.5×10－6 mol/L, 线性相关系数为0.9976, 检测限为 1.9×10－8 mol/L.     

CdTe/CdSe核壳量子点的合成及其在指纹显现中的应用

以CdCl2和Te粉为原料,在水相中合成了CdTe量子点核;通过外延生长在CdTe量子点核上包覆一层CdSe量子点,得到具有良好荧光性能的CdTe/CdSe核壳量子点;采用X射线衍射仪、透射电镜、高分辨透射电镜分析了不同反应条件下合成的CdTe/CdSe核壳量子点的晶体结构和微观结构,并对其进行了荧光光谱等测试和指纹显现分析.结果表明,合成的CdTe和CdTe/CdSe量子点粒径在3～5nm之间,粒径分布窄,水分散性良好;可以通过控制反应时间和Te/Se比等得到在500～700nm显示荧光发射峰的CdTe/CdSe核壳量子点.此外,核壳CdTe/CdSe量子点可以有效地和指纹物质结合,可应用于对铝合金油潜指纹的鉴别.     

核壳结构AgInS2@ZnS量子点的合成及荧光性能

合成了一种新型核壳结构的AgInS₂@ZnS量子点并研究了其荧光性能. AgInS₂@ZnS的合成包括以变性牛血清白蛋白(dBSA)为稳定剂水相法构建AgInS₂核以及形成ZnS壳两部分. 考察了配方和工艺条件对该量子点荧光性能的影响, 并采用X射线粉末衍射(XRD)等手段对制备的纳米粒子进行了表征. 结果表明, AgInS₂@ZnS是一种核壳结构的纳米物质, 其粒径介于5~7 nm之间, 荧光量子产率达35.3%.     

CdSe包覆层数对水溶性CdTe/CdSe (II型)核壳量子点的光学特性和微观结构的影响

在水相合成的CdTe量子点的体系中通过分批次加入新鲜配制的NaHSe和CdCl2溶液,制备出了CdSe包覆层数不同的CdTe/CdSe核壳量子点,并着重考察了CdSe包覆层数对CdTe/CdSe核壳量子点的光学特性以及微观结构的影响.与CdTe量子点相比,CdSe单层包覆的CdTe/CdSe核壳量子点的吸收峰和荧光发射峰出现明显红移;随着CdSe包覆层数的增多,CdTe/CdSe核壳量子点吸收光谱的覆盖范围向长波方向扩展,荧光发射峰强度逐步下降,荧光寿命大幅延长,体现出Ⅱ型核壳量子点的特征.X射线衍射(XRD)分析表明,随着CdSe包覆层数的增多,CdTe/CdSe核壳量子点的粉末衍射峰由CdTe衍射峰位置逐步向CdSe衍射峰位置靠近.CdTe/CdSe核壳量子点因其延伸到近红外区域的宽吸收特性致使其在太阳电池领域具有重要的应用前景.     

A rapid and universal bacteria-counting approach using CdSe/ZnS/SiO2 composite nanoparticles as fluorescence probe

In this paper, a rapid, simple, and sensitive method was described for detection of the total bacterial count using SiO₂-coated CdSe/ZnS quantum dots (QDs) as a fluorescence marker that covalently coupled with bacteria using glutaraldehyde as the crosslinker. Highly luminescent CdSe/ZnS were prepared by applying cadmium oxide and zinc stearate as precursors instead of pyrophoric organometallic precursors. A reverse-microemulsion technique was used to synthesize CdSe/ZnS/SiO₂ composite nanoparticles with a SiO₂ surface coating. Our results showed that CdSe/ZnS/SiO₂ composite nanoparticles prepared with this method possessed highly luminescent, biologically functional, and monodispersive characteristics, and could successfully be covalently conjugated with the bacteria. As a demonstration, it was found that the method had higher sensitivity and could count bacteria in 3 × 10² CFU/mL, lower than the conventional plate counting and organic dye-based method. A linear relationship of the fluorescence peak intensity (Y) and the total bacterial count (X) was established in the range of 3 × 10²–10⁷ CFU/mL using the equation Y = 374.82X − 938.27 (R = 0.99574). The results of the determination for the total count of bacteria in seven real samples were identical with the conventional plate count method, and the standard deviation was satisfactory.     

Determination of the size of quantum dots by fluorescence spectroscopy

There has been a lack of quick, simple and reliable methods for determination of nanoparticle size. An investigation of the size of hydrophobic (CdSe) and hydrophilic (CdSe/ZnS) quantum dots was performed by using the maximum position of the corresponding fluorescence spectrum. It has been found that fluorescence spectroscopy is a simple and reliable methodology to estimate the size of both quantum dot types. For a given solution, the homogeneity of the size of quantum dots is correlated to the relationship between the fluorescence maximum position (FMP) and the quantum dot size. This methodology can be extended to the other fluorescent nanoparticles. The employment of evolving factor analysis and multivariate curve resolution-alternating least squares for decomposition of the series of quantum dots fluorescence spectra recorded by a specific measuring procedure reveals the number of quantum dot fractions having different diameters. The size of the quantum dots in a particular group is defined by the FMP of the corresponding component in the decomposed spectrum. These results show that a combination of the fluorescence and appropriate statistical method for decomposition of the emission spectra of nanoparticles may be a quick and trusted method for the screening of the inhomogeneity of their solution.     

Optical Determination of Cholesterol in Milk with Molecularly Imprinted Polymer-Coated Quantum Dots

Fluorescent molecularly imprinted polymer-coated CdSe/ZnS quantum dots were prepared in an efficient one-step synthesis. Their application as fluorescent nanoparticles for the direct quantification of cholesterol in milk was characterized. The quantum dots were used as cores to produce fluorescence. The molecularly imprinted polymer shells provided specific binding sites for cholesterol. The system exhibited good linearity for cholesterol from 0.5 to 150?µg?mL^?1, a low detection limit of 0.15?µg?mL^?1, and acceptable reproducibility with a relative standard deviation of 4.2% for six replicates. The molecularly imprinted polymer-coated quantum dots were used to determine cholesterol in fortified milk. Recoveries were from 87.0 to 105.2% and a possible mechanism is proposed. The fluorescent molecularly imprinted polymer-coated quantum dots exhibited excellent selectivity and provide a simple, rapid, selective, and effective analytical approach.     

CdSe/ZnS quantum dots based fluorescence quenching method for determination of paeonol

Aqueous polymethylmethacrylate (PMMA)-capped CdSe/ZnS quantum dots were used as fluorescence probes for paeonol determination. Based on the fluorescence quenching of aqueous CdSe/ZnS quantum dots caused by paeonol, a simple, sensitive and rapid method was developed. Under the optimal conditions, with excitation and emission wavelengths at 350 nm and 620 nm, respectively, the calibration plot of F0-F with concentration of paeonol was linear in the range of 25.04-175.2 mg L(-1) with correlation coefficient of 0.9986. The limit of detection was 0.017 mg L(-1). The concentration of paeonol in paeonol ointment was determined by the proposed method and the result agreed with the claimed value. Furthermore, the possible fluorescence quenching mechanism was discussed.     

水溶性CdSe量子点的合成及其作为荧光探针对大肠杆菌的快速检测

采用水相法以谷胱甘肽为稳定剂合成高稳定性的CdSe量子点,利用化学偶联剂的作用使得量子点表面基团与菌体之间的成功结合,对偶联的条件进行了优化.基于荧光分析法建立了一种快速简便的大肠杆菌检测定量分析方法.研究结果表明:合成的量子点具有稳定、荧光性能良好等突出优点.通过偶联剂量子点能与大肠杆菌结合,其荧光强度与大肠杆菌浓度...     

基于CdSe/ZnS量子点构建丝裂霉素荧光检测体系的研究

建立了一种基于CdSe/ZnS量子点的快速、高效的检测丝裂霉素的荧光方法。pH=7.4,反应10 min,CdSe/ZnS量子点的荧光随丝裂霉素浓度增加而猝灭,量子点的荧光强度与丝裂霉素的浓度呈良好的线性关系,适用于丝裂霉素浓度1.8~60 μmol/L,且相关系数为0.996,丝裂霉素的检测限为0.11 μmol/L,该方法相对无共存物质的干扰,并证明完全适用于丝裂霉素注射液与尿液中丝裂霉素的测定。     

Photostability of complexes based on fluorescent CdSe/ZnS nanoparticles and polyelectrolytes

By means of fluorescence spectroscopy, it has been found that the oscillator strength of the electronic transition in CdSe/ZnS nanoparticles increases when the hydrophilic fluorescent CdSe/ZnS nanoparticles form complexes with cationic and anionic polyelectrolytes. However, an increase in the relative quantum yield and photostability is possible only in the complexes of the anionic shell-covered CdSe/ZnS nanoparticles with polycations. The mechanisms of the effect of ionic interactions on the probabilities and channels of electronic transitions in the nanoparticles are discussed.     

Layer-by-layer quantum dot constructs using self-assembly methods

We describe the creation of CdSe/ZnS quantum dot assemblies using layer-by-layer construction strategies, using self-assembly. In the first approach, a dithiol linker was used to make multilayers of CdSe/ZnS quantum dots, while in the second biotin- and streptavidin-conjugated CdSe/ZnS quantum dots were used to make multilayer constructs. Both the chemical bonding nature and fluorescence spectroscopic properties of quantum dot films were characterized using X-ray photoelectron spectroscopy (XPS) and fluorescence spectroscopy.     

Preparation and Properties of Magnetic-fluorescent Microporous Polymer Microspheres

Microporous microspheres can be used as functional nanomaterial carriers for their microporous structure and higher specific surface area. In this study, magnetic fluorescent polymer microspheres were prepared by incorporating Fe₃O₄ nanoparticles and CdSe/ZnS quantum dots(QDs) into hyper-crosslinked microporous polymer microspheres(HCMPs) via the in situ coprecipitation method and swelling-diffusion. The HCMPs predominantly have micropores, and their specific surface area is as high as 703.4 m²/g. The magnetic-fluorescent microspheres maintain the superparamagnetic behavior of Fe₃O₄, and the saturation magnetization reaches 38.6 A·m²/kg. Moreover, the composite microspheres exhibit an intense emission peak at 530 nm and achieve good fluorescence.