1,8-二（2-羟乙基）亚氨基蒽醌荧光探针用于Fe3+的高选择性测定

在蒽醌荧光团上修饰乙醇胺分子,合成了用于铁离子识别检测的新的荧光探针.实验结果表明,在乙醇∶水=4∶1,pH值为7.20的条件下,Fe3+的加入使体系荧光猝灭,荧光强度和Fe3+浓度在4.0×10-5—3.0×10-4 mol/L范围内呈线性关系,由此可以实现在乙醇/水体系中对Fe3+离子的高选择性检测.检测限为3.8×10-7 mol/L.     

一种新型苝类荧光开关的构建及对H2O2与Vc分子的识别

以苝四酸酐为原料合成了新型的水溶性荧光分子——N,N’-二谷氨酸铵盐-3,4,9,l0-苝四羧酸二酰亚胺(PTCDG),其结构经1 H NMR、IR证实.以顺磁性Fe3+和抗磁性Fe2+与PTCDG构建荧光开关,当以顺磁性的Fe3+存在时,荧光团和Fe3+之间发生PET效应,荧光猝灭,而当以抗磁性的Fe2+存在时,PE...     

基于咔唑衍生物的荧光化学传感器的合成及其对金属离子的选择性识别性能

以咔唑为原料合成了2个荧光化学传感器,所得化合物的组成和结构经元素分析以及质谱、红外光谱、核磁共振氢谱验证.通过在25℃下进行荧光光谱滴定,研究了传感器在体积比为1∶1的二甲基亚砜/水缓冲溶液[三羟甲基氨基甲烷盐酸盐(Tris-HCl),pH=7.4]中对Cu2+和Fe3+的选择性识别作用.结果表明,所合成的传感器与Cu2+和Fe3+形成1∶1的配合物并导致荧光猝灭,并对Cu2+离子和Fe3+离子具有较高的选择性识别和荧光传感性能.     

水溶液中对Cr~(3+)高选择性荧光化学传感器的研究

设计了一种新型的Cr3+荧光化学传感器.通过荧光光谱滴定实验研究了其对Li+,Na+,K+,Zn2+,Co2+,Ni 2+,Cu2+,Fe2+,Mn2+,Al 3+,Fe3+和Cr3+等不同金属离子的选择性识别能力,结果表明,该传感器在生理pH=7.4的HEPES中对Cr3+表现出较高的选择性,并与Cr3+形成1∶1配合物,主客体相互作用荧光猝灭的络合常数为(7.80±0.34)×103.     

Hg~(2+)荧光传感器的设计及合成(英文)

设计合成了一种新颖的基于萘荧光基团的Hg2+荧光传感器.通过荧光光谱滴定实验研究了其对Hg2+、Li+、Na+、K+、Zn2+、Co2+、Ni 2+、Cu2+、Fe2+、Mn2+、Cr3+和Fe3+等金属离子的选择性识别能力.结果表明,该传感器在生理pH=7.4的H2O-DMSO中对Hg2+表现出较高的选择性,并且形成1∶1的配合物;主客体相互作用荧光猝灭的络合常数为(9.07±0.41)×104.     

（英）一种基于共振瑞利散射和荧光增强并对Fe3 和 Fe2 具有高识别作用的荧光方法的研究

本文合成了4-甲基哌嗪-1,8-萘酰亚胺修饰的β-环糊精,该化合物对Fe3+和Fe2+展现出良好的选择性识别能力。当适量的氨水加入到该化合物水溶液中后,溶液体系的荧光被完全猝灭。然而,当Fe3+和Fe2+加入到该溶液体系后,520nm处的荧光信号和416nm处的共振瑞利散射峰均逐渐增强。Fe3+和Fe2+引起的荧光强度和共振瑞利散射强度比值的差异可用于鉴别Fe3+和Fe2+,同时,该方法还展现了较高的灵敏度。本文建立的方法对Fe3+检测的线性范围为1.5×10-5~2.2×10-5mol/L,检测限为1.1×10-5mol/L;对Fe2+检测的线性范围为0.5×10-5~4.2×10-5mol/L,检测限为0.6×10-5mol/L。     

铜(Ⅱ)与明胶络合反应的酸效应研究

本文利用分光光度法,测定了pH值为80～130时,Cu²⁺与明胶的络合比.结果发现,随溶液pH值的增大,其络合比增加.这是因为在该pH值范围内,明胶发生去质子化作用而带负电,提供了更多的NH₂—和COO^-.通过络合物的荧光光谱表明,由于Cu²⁺与明胶分子的强烈络合作用,使得Cu²⁺成为明胶有效的荧光猝灭剂.     

用于检测Al3+和pH值的双功能荧光分子探针

利用荧光素(Fluorescein)对罗丹明6G(Rhodamine 6G)进行修饰,得到荧光分子探针R6G-Flu杂化物.此探针可特异性识别Al3+,检出限可低至10-8 mol/L级;向含有探针分子的溶液中加入Al3+后,溶液的颜色由无色变为粉色,并且在紫外灯下发出绿色荧光,可实现肉眼对10 μmol/L Al3+的定性检测.考察了不同pH值下R6G-Flu的荧光性质. 结果表明,此探针还可用于酸性范围(pH 3.00~6.00)和碱性范围(pH 8.00~10.50)内pH值的精确检测.实验结果表明,R6G-Flu是一种可用于Al3+和pH值检测的双功能荧光分子探针.     

荧光金纳米团簇的制备及其在铜离子检测中的应用

在水溶液中以谷胱甘肽(Glutathione,GSH)为稳定剂和还原剂,制备了具有较好荧光性能的金纳米团簇(GSH-AuNCs),对其结构和荧光性能等进行了表征。基于Cu2+对该GSH-AuNCs的荧光具有选择性猝灭作用建立了一种快速且简便的检测痕量Cu2+的方法。考察了检测体系中GSH-AuNCs的浓度、反应时间、pH值等因素对测定的影响。结果表明,在最优实验条件下,GSH-AuNCs的荧光强度与Cu2+的浓度分别在5.0×10-9～4.0×10-6 mol/L(R=0.9940),4.0×10-6～2.0×10-5 mol/L(R=0.9950)范围呈良好线性关系,检出限(S/N=3)为2.0×10-9 mol/L。该方法成功地应用于实际水样中Cu2+的检测。     

基于可识别不同价态铁离子的多控荧光开关及分子逻辑门的构建

本文研究了5-磺基水杨酸(SSA)与多种金属离子的相互作用的荧光光谱,发现Fe3+可以选择性猝灭SSA的荧光,而其他金属离子如Ca2+、K+、Cr3+、Ni 2+Mn2+、Pb2+、Cu2+、Zn2+、Co2+以及Fe2+均不能猝灭SSA的荧光。同时发现,加入EDTA竞争Fe3+或加入盐酸羟胺还原Fe3+均可以使SSA的荧光恢复。可以通过质子(H+/OH-)、配位(Fe3+/EDTA)和化学氧化还原(盐酸羟胺/K2S2O8)三种方式对其荧光进行可逆调控。在此基础上,分别以SSA和SSA-Fe3+体系作为起始状态,构建了两化学输入的NOR、OR和INHIBIT分子逻辑门。     

A simple,water-soluble,Fe3+-selective fluorescent probe and its application in bioimaging

A simple,water-soluble,Fe³⁺-selective fluorescent probe,derived from rhodamine B,was synthesized and characterized.The probe exhibits a fluorescence response toward Fe³⁺ with acceptable sensitivity and selectivity and even facilitates visual or naked-eye detection of Fe³⁺.The experiment results show that the response of the probe to Fe³⁺ is pH-independent over a wide range of 4.0-10.0.In addition,fluorescence microscopic imaging experiments have proven that the probe is cell permeable and can be used for monitoring intracellular Fe³⁺ in living cells.     

Solution equilibria in l-glutamic acid and l-serine + iron(III) systems

Complex formation equilibria in l-glutamic acid (H2Glu) and l-serine (HSer) +iron(III) ion systems have been studied by a combination of glass electrode potentiometric and visible spectrophotometric measurements in 0.5 mol dm–3 (Na)NO3 ionic medium at 25°C. In the concentration range 1.0[Fe3+]5.0; 3.0[Glu2–]30.0 mmol dm–3 ([Glu]/[Fe]=3:1 to 30:1) and pH between 1.5 and 4.5, iron(III) and glutamic acid form the Fe(Glu)–2, Fe(Glu)+, Fe(HGlu)2+, Fe(OH)Glu, Fe2(OH)2Glu2+, Fe(OH)Glu22– complexes: and several pure hydrolytic products. Iron(III) and l-serine, beside pure hydrolytic complexes of iron(III), form the Fe(HSer)3+, Fe(Ser)2+, Fe(OH)Ser+, Fe(OH)2- Ser0, Fe(OH)Ser2 and Fe2(OH)2(Ser)2+2 complexes, over a broad concentration range of serine to iron ([Ser]/[Fe]=5:1 to 500:1), from pH 1.5 to 4.0. The stability constants of the complexes are given and their formation mechanism is suggested. The possible structure of the complexes, in solution, is discussed.     

On the formation of iron(III) hydroxo acetate complexes

The formation of hydroxo acetate complexes of iron (III) ion has been studied at 25 degrees C in 3 M (Na)ClO4 ionic medium by measuring with a glass electrode the hydrogen ion concentration in Fe(ClO4)3-HClO4-NaAc mixtures (Ac = acetate ion). The acetate/metal ratio ranged from 0 to 6, the metal concentration varied from 0.005 to 0.06 M, whereas [H+] was stepwise decreased from 0.1 M to initial precipitation of hydroxo-acetates. This occurred, depending on the acetate/metal ratio, in the -log[H+] range 1.85-2.7. The potentiometric data are consistent with the presence of Fe3(OH)3Ac3(3+), Fe2(OH)2(4+), Fe3(OH)4(5+), Fe3(OH)5(4+) and, as minor species, of Fe3(OH)2Ac6+, FeAc2+, FeAc2+, FeOH2+ and Fe(OH)2+. Previously published EMF measurements with redox and glass half-cells were recalculated to refine the stability constants of FeAc2+, FeAc2+ and Fe3(OH)2Ac6+. Formation constants *beta pqr for pFe(3+)+(q-r)H2O + rHAc reversible Fep(OH)(q-r)(Ac)r3p-q + qH+ (in parenthesis the infinite dilution value): log*beta 111 = -1.85 +/- 0.02 (-0.67 +/- 0.15), log*beta 122 = -3.43 +/- 0.02 (-1.45 +/- 0.15); log*beta 363 = -5.66 +/- 0.03 (-2.85 +/- 0.40), log*beta 386 = -8.016 +/- 0.006 (-4.06 +/- 0.15), log*beta 220 = -2.88 +/- 0.02 (-2.84 +/- 0.05), log*beta 340 = -6.14 +/- 0.18 (-6.9 +/- 0.4), log*beta 350 = -8.44 +/- 0.09 (-7.65 +/- 0.15).     

离子色谱电感耦合等离子体质谱研究痕量氯金酸在弱碱性体系中金(Ⅲ)的形态

采用离子色谱电感耦合等离子体质谱联用方法研究弱碱性体系下痕量氯金酸中Au(Ⅲ)的形态.结果表明:在弱碱性条件下,总金含量在4.0～30 ng之间,Au(Ⅲ)主要以[AuCl2( OH)2]-和[AuCl(OH)3]-的形式存在.与较高含量的氯金酸溶渡相比,痕量氯金酸溶液中的[AuCl2(OH)2]-至少可以在pH 7.0～10.0范围内存在.溶液外加的Cl-可使[AuCl2 (OH)2]-含量升高同时降低[AuCl (OH)3]-含量;当pH=7.0或Cl-浓度高于0.050 mol/L,会产生不随色谱流出的金络合物,根据水解过程推断该络合物为[AuC13 (OH)]-.在pH 8.0～10.0,Cl-浓度在0.000～0.020 mol/L时,[AuCl2(OH)2]-+OH-=[AuCl (OH)3]-+Cl-的水解平衡常数为不定值,说明痕量氯金酸的水解不仅受pH值和Cl-浓度影响,还受其它因素影响.     

罗丹明类荧光探针的合成及对铜离子的检测

合成了罗丹明类Cu2+荧光增强型分子探针3',6'-双(二乙氨基)-2-(N-乙叉基氨基)螺[异吲哚-1,9'-占吨]-3-酮（RA）,并研究了它的光谱性能及对铜离子的识别作用.在乙腈/水（体积比1/1）的介质中,当加入Cu2+后探针RA显玫瑰红色,最大吸收波长为548 nm,最大发射波长为571 nm,且荧光强度显著增强,但是,其它常见离子如Na+, K+, Mg2+, Ca2+, Mn2+, Cd2+, Cr3+, Co2+, Ni2+, Ag+, Pb2+, Zn2+, Fe3+, Hg2+不引起或引起很小的紫外/可见或荧光光谱变化.RA的选择性荧光增强主要是由于Cu2+诱导分子中的酰胺闭环结构发生开环,导致分子结构的共轭程度增大.在6.5×10-8～2.9×10-6 mol?L-1范围内RA可以有效检测Cu2+,检测限为5.0×10-8 mol?L-1.RA对Cu2+的识别不可逆,而且探针RA对pH值不敏感,可以在比较宽的范围内（pH=4.1～10.5）高灵敏、高选择性检测Cu2+.     

Limitation of ferrozine method for Fe(II) detection: reduction kinetics of micromolar concentration of Fe(III) by ferrozine in the dark

The dark reduction kinetics of micromolar concentrations of Fe(III) in aqueous solution were studied in the presence of millimolar concentrations of ferrozine (FZ) over the pH range 4.0–7.0. A pseudo-first-order kinetics model was used to describe Fe(III) reduction at pH 4.0 and 5.0, and the reduction rate decreased with increasing pH or initial Fe(III) concentration. A more molecular-based kinetics model was developed to describe Fe(III) reduction at pH 6.0 and 7.0. From this model, the intrinsic rate constants (k₁) of Fe(III) reduction by FZ in the dark were obtained as 0.133 ± 0.004 M^?1 s^?1 at pH 6.0 and 0.101 ± 0.009 M^?1 s^?1 at pH 7.0. It was also found in this model that a higher pH, a higher concentration of Fe(III), a lower concentration of FZ and less incubation time led to a lower fraction of Fe(III) reduction by FZ in the dark.     

Mercury(II) ion-selective electrodes based on p-tert-butyl calix[4]crowns with imine units.

A PVC membrane incorporating p-tert-butyl calix[4]crown with imine units as an ionophore was prepared and used in an ion-selective electrode for the determination of mercury(II) ions. An electrode based on this ionophore showed a good potentiometric response for mercury(II) ions over a wide concentration range of 5.0 x 10(-5) - 1.0 x 10(-1) M with a near-Nernstian slope of 27.3 mV per decade. The detection limit of the electrode was 2.24 x 10(-5) M and the electrode worked well in the pH range of 1.3 - 4.0. The electrode showed a short response time of less than 20 s. The electrode also showed better selectivity for mercury(II) ions over many of the alkali (Na+, -1.69; K+, -1.54), alkaline-earth (Ca2+, -3.30; Ba2+, -3.32), and heavy metal ions (Co2+, -3.67; Ni2+, -3.43; Pb2+, -3.31; Fe3+, -1.82). Ag+ ion was found to be the strongest interfering ion. Also, sharp end points were obtained when the sensor was used as an indicator electrode for the potentiometric titration of mercury(II) ions with iodide and dichromate ions.     

A novel wire-type lead-selective electrode based on bis (1'-hydroxy-2'-acetonaphthone)-2,2'-diiminodiethylamine

The preparation of a lead-selective electrode based on bis(1'-hydroxy-2'-acetonaphthone)-2,2'-diiminodiethylamine (L) as sensing material is reported. The plasticized PVC membrane containing 30% PVC, 67% ortho-nitrophenyloctylether (NPOE) and 3% ionophore L was directly coated on a graphite rod. This electrode exhibits a nearly Nernstian slope of 27.8+/-0.2 mV decade(-1) over a concentration range 10(-6)-10(-2) M with a detection limit of 4.0 x 10(-7) M. The response time of the electrode was found to be <20 s. The potential of the sensor was independent on pH variations in the range 5-7. The selectivity of the electrode towards lead ions over Na+, K+, Ag+, Ca2+, Sr2+, Fe2+, Co2+, Ni2+, Cu2+, Zn2+, Cd2+, La3+, Sm3+ and Er3+ ions was investigated. The prepared electrode was successfully used as an indicator for titration of a lead solution with a standard solution of EDTA. The applicability of the sensor for Pb2+ measurement in various synthetic and real samples has been also demonstrated.     

荧光试剂SPAEC的合成及分析化学特性研究

合成了新荧光试剂2-(5'-磺基-2'-苯酚-1'-偶氮)-5-乙氨基-4-甲酚(SPAEC)。用等色点光度法测得试剂的离解常数为pK1=3.42, pK2=5.46, pK3=7.99。考察了SPAEC与金属离子的螯合显色和荧光反应; 建立了测定镓、铝的反应条件, 在PH3.8-5.4或PH4.0-5.5的乙酸缓冲介质中均形成:1型具荧光活性的有色螯合物, 可相应测定15-150ppb镓及1.5-30ppb铝, 试用于半导体及合金分析。研究了Kalman滤波荧光光度法, 实现了镓与铝的同时测定, 所适应的浓度比例范围为40:1(0)-1(0):14。     

Hydroxo sulfate complexes of iron (III) in solution

The ternary Fe (III)-OH(-)-SO4(2-) complexes have been investigated at 25 degrees C in 3 M NaClO4 by potentiometric titration with glass electrode. The metal and sulfate concentrations ranged from 2.5 x 10(-3) to 0.03 M and from 5.10(-3) to 0.060 M, respectively. [H+] was decreased from 0.05 M to incipient precipitation of basic sulfate which occured at log[H+] between -2.3 and -2.5 depending on the concentration of the metal. For the interpretation of the data stability constants of HSO4(-), of binary hydroxo complexes (FeOH2+, Fe(OH)2+, Fe2(OH)2(4+), Fe3(OH)4(5+), Fe3(OH)5(4+)) and of sulfate complexes (FeSO4+, FeHSO4(2+), Fe(SO4)2-) were assumed from independent sources. The data are consistent with the presence of FeOHSO4, log beta 1-11 = -0.49 +/- 0.03. Equilibrium constants are defined as beta pqr for pFe3+ +qH+ +rSO4(2-) [symbol: see text] FepHq(SO4)r3p+q-2r. No substantial better fit could be found by adding a second mixed complex. Only a slightly smaller agreement factor resulted introducing as minor ternary complex Fe3(OH)6(SO4)3(3-) with log beta 3-63 = -5.8 +/- 0.5. Its evidence, however, cannot be considered conclusive.