预浓缩/色谱-质谱测量大气中挥发性有机硫化合物

硫循环是生物地化循环中最复杂的循环之一. 近年来,由于人类活动的影响,大气中硫化物含量急剧增加. 这些硫化物与大气中自由基发生作用,形成SO2、H2SO4和硫酸盐, 导致环境酸化, 酸沉降加剧.硫酸盐气溶胶的形成还改变了大气云层特性,影响大气臭氧含量的垂直分布以及大气热量辐射,对温室效应有一定的贡献[1-3].挥发性有机硫化合物中的甲硫醇(MT),甲硫醚(DMS),二硫化碳(CS2)和二甲二硫(DMDS)还是国家标准控制《恶臭污染物排放标准》中规定的4种恶臭气体,对大气环境质量造成一定的影响.     

蓄热式热氧化炉处理农药行业挥发性有机废气

以农药行业挥发性有机废气为研究对象,优化了蓄热陶瓷体、切换阀、燃烧器等选材,以及安全控制和二噁英防治等方面设计参数,分析了特征污染物进出气浓度及去除效率,探讨了蓄热式热氧化(Regenerative Thermal Oxidizer,RTO)技术治理挥发性有机废气实际运行效果。结果表明甲苯和非甲烷总烃排放限值满足《大气污染物综合排放标准》(GB16297-1996)中表2二级标准,二氯乙烷排放限值满足美国EPA工业环境实验室和《制定地方大气污染物排放标准的技术方法》(GB/T3840-1991)计算值,二噁英排放限值满足《生活垃圾焚烧污染控制标准》(GB18485-2014)表4标准。RTO系统总投资150万元,年运行费用49.98万元,对该企业不构成经济负担。RTO适合农药行业挥发性有机废气处理,特别是对含低浓度卤素废气在保证净化效果的同时又可抑制二噁英产生。     

臭氧标准参考光度计的国际间接比对技术

正臭氧是城市环境空气中最为重要的二次污染物之一,主要由燃烧等污染源排放的一次污染物NOx和挥发性有机物(VOCs)在太阳紫外线作用下发生一系列光化学反应而生成[1]。世界卫生组织在2005年新发布的《空气质量指南》中设立了臭氧浓度的长期目标、阶段目标及最高限值[2]。由于臭氧具有强氧化性,难以制备稳定、可靠的臭氧气体标准样品,因此臭氧校准不同于常规污染物监测时采用     

顶空-气相色谱-质谱法测定水和废水中二甲基甲酰胺

正二甲基甲酰胺(DMF)是优良的有机溶剂,广泛用于各化工行业,特别是在合成纤维和合成皮革制造行业中会使用和排放大量DMF。《合成革与人造革工业污染物排放标准》[1]中新建企业水污染物DMF的排放限值为2mg·L~(-1),推荐的检测方法为工作场所空气有毒物质的测试方法[2],该方法采用水样直接进气相色谱分析,检出限为5mg·L~(-1),不能满足限值要求,且使用废水直接进样会严重损耗     

气质联用法测定饮用水中29种挥发性有机物

挥发性有机物(VOCs)具有高挥发性、类脂物可溶性、易被皮肤、粘膜吸收等特点,对环境和人体有较大的影响和危害.新<生活饮用水卫生标准>(GB/T 5749-2006)[1]中VOCs的检测项目从原来的2项增加到25项.顶空气相色谱是过去测定水中VOCs的常用方法,但该法灵敏度较低,不适于数十种挥发性有机物同时检测[2].新技术吹扫捕集-气质联用法(P&T-GC-MS)能同时分析测定多种物质,前处理方式也较简便,因此成为测定水中VOCs的推荐方法[3-6].     

吹扫捕集-GC-MS-SIM法测定水中挥发性硫化合物

建立了水中的二硫化碳(CS2)、甲硫醚(DMS)和二甲二硫醚(DMDS) 3种挥发性硫化合物分析方法.采用吹扫-捕集对水中的被测成分进行预富集,然后导入GC-MS系统中在选择离子模式(SIM)下进行检测.CS2、DMS和DMDS 3种硫化合物分别在0.03～3.42 μg/L,0.17～2.72 μg/L和0.04～3.41 μg/L范围内线性关系良好,相关系数r分别为0.9967、0.9930和0.9959;在不同的浓度下,平行测定5次后的相对标准偏差均小于6.0%;方法检出限为3.75,11.33和2.10 ng/L.     

蒸馏法测定一次性筷子中二氧化硫浸出量的不确定度评定

依照GB 19790.1-2005,GB 19790.2-2005和GB/T 5009.34-2003(第二法),选取含量接近法规限值的代表性样品,从基准物质和标准滴定溶液溯源,探索测定一次性筷子中二氧化硫浸出量的数学模型,对检测过程中引入的不确定度进行了分类和量化,系统地评定了各个不确定度分量,得到该方法的相对标准不确定度为0.0043.     

磁增强光电子电离便携式飞行时间质谱仪的研制及其在挥发性还原态硫化物测量中的应用

还原态硫化物是大气主要污染物之一。本研究利用自行研制的磁增强光电子电离便携式飞行时间质谱,对还原态硫化物的测量方法进行了研究。光电子由真空紫外灯发射的10.6 e V的光子照射金属电极表面产生,通过调节引出电压控制光电子能量发生光电子电离。为提高光电子电离的效率,在电离区中设置了环形磁铁。利用SIMION软件模拟发现磁场的引入使电子呈螺旋运动,增加电子运动路径,同时实现电子向电离区中心的汇聚。实验结果表明,磁场的引入使3种还原态硫化物H2S,SO2和CS2的灵敏度分别提高了5.3、9.4和6.9倍,50 s检测时间对3种物质的检测限分别达到0.14、0.52和0.31 mg/m3(S/N=3)。结果表明,磁增强光电子电离的便携式飞行时间质谱仪有望应用于挥发性硫化物的源排放在线监测。     

吹扫捕集–气相色谱–质谱法同时测定环境水中101种挥发性有机物

建立吹扫捕集–气相色谱–质谱联用法测定环境水中101种常见挥发性有机物(VOCs)的方法。通过加热吹扫,样品水中的VOCs富集于捕集管中,以DB–624(60 m×0.25 mm,1.4μm)色谱柱分离,内标法定量。结果表明,101种挥发性有机物(VOCs)色谱分离效果良好,质量浓度在0.5~50 ng/mL范围内与色谱峰面积均呈线性关系,高沸点VOCs线性范围较窄。方法定量限(10 S/N)为0.11~0.77 ng/mL,均低于GB 3838–2002《地表水环境质量标准》、GB 5749–2006《生活饮用水卫生标准》及国外相关标准的限值。平均加标回收率在70.3%~123.6%之间,测定结果的相对标准偏差不大于8.8%(n=6)。该方法快速、简便,适用于环境水中挥发性有机化合物的分析检测。     

恶臭气体中含硫组分的气相色谱快速检测系统研究

根据恶臭气体中含硫物质的特性,选用Silica Bond Plot色谱柱作为分离系统,设计了自动进样模块与色谱快速加热模块,选择灵敏度高与通用性好的光离子化气体传感器作为气体检测器,组建了GC-PID快速在线检测系统。选择了恶臭气体中的H2S,CS2,甲硫醇,甲硫醚,乙硫醇,乙硫醚和二甲基二硫醚等7种含硫化合物的混合气体进行分离检测。结果表明,检测周期小于12 min,最佳分离温度为90℃~150℃,载气流量控制为2.5 m L/min。     

Determination of flavone C-glucosides in antioxidant of bamboo leaves (AOB) fortified foods by reversed-phase high-performance liquid chromatography with ultraviolet diode array detection

A sensitive solid-phase microextraction and gas chromatography-pulsed flame photometric detection technique was developed to quantify volatile sulfur compounds in wine. Eleven sulfur compounds, including hydrogen sulfide, methanethiol, ethanethiol, dimethyl sulfide, diethyl sulfide, methyl thioacetate, dimethyl disulfide, ethyl thioacetate, diethyl disulfide, dimethyl trisulfide and methionol, can be quantified simultaneously by employing three internal standards. Calibration curves were established in a synthetic wine, and linear correlation coefficients (R2) were greater than 0.99 for all target compounds. The quantification limits for most volatile sulfur compounds were 0.5 ppb or lower, except for methionol which had a detection limit of 60 ppb. The recovery was studied in synthetic wine as well as Pinot noir, Cabernet Sauvignon, Pinot Grigio, and Chardonnay wines. Although the sulfur compounds behaved differently depending on the wine matrix, recoveries of greater than 80% were achieved for all sulfur compounds. This technique was applied to analyze volatile sulfur compounds in several commercial wine samples; methionol concentrations were found at the ppm level, while the concentrations for hydrogen sulfide, methanethiol, and methyl thioacetate were at ppb levels. Only trace amounts of disulfides and trisulfides were detected, and ethanethiol was not detected.     

Determination of volatile organic sulfur compounds in the air at sewage management areas by thermal desorption and gas chromatography-mass spectrometry

The concentrations of seven volatile organic sulfur compounds (VOSCs) in air samples were determined by active collection on multisorbent tubes followed by two-stage thermal desorption and gas chromatography-mass spectrometry. The compounds studied were ethyl mercaptan (CH(3)CH(2)SH), dimethyl sulfide ((CH(3))(2)S), carbon disulfide (CS(2)), propyl mercaptan (C(3)H(8)S), butyl mercaptan (C(4)H(10)S), dimethyl disulfide ((CH(3))(2)S(2)) and 1-pentanethiol (C(5)H(12)S). Active collection on SilcoSteel multisorbent tubes enabled an air volume of 3000ml to be sampled without observing breakthrough. This study focused on an exhaustive sampling of several process steps or sections from sewage management plants. A wide range of concentrations was observed. Dimethyl sulfide, carbon disulfide and dimethyl disulfide were the most abundant compounds in all samples, the highest concentrations being 608.5microg m(-3), 658.5microg m(-3) and 857.8microg m(-3), respectively. The less appearing compound was ethyl mercaptan, which was only detected in the sludge digestion process at a maximum concentration of 14.8microg m(-3). The remaining compounds were detected and measured in about half the samples. The sections with the maximum values of VOSCs involved sludge processes such as mixing, thickening and digestion. The results were also strongly influenced by the design characteristics of the sampling point, e.g. whether the sample was taken at a confined site or in the open air.     

The fundamental properties of the direct injection method in the analysis of gaseous reduced sulfur by gas chromatography with a pulsed flame photometric detector

In this study, the fundamental aspects of gas chromatography with a pulsed flame photometric detector were investigated through the calibration of gaseous reduced sulfur compounds based on the direct injection method. Gaseous standards of five reduced sulfur compounds (hydrogen sulfide, methane thiol, dimethyl sulfide, carbon disulfide, and dimethyl disulfide) were calibrated as a function of injection volume and concentration level. The results were evaluated by means of two contrasting calibration approaches: fixed standard concentration method (variable volumetric injection of standard gases prepared at a given concentration) and fixed standard volume method (injection of multiple standards with varying concentrations at a given volume). The optimum detection limit values of reduced sulfur compounds, when estimated at 100 μL of injection volume, ranged from 2.37 pg (carbon disulfide) to 4.89 pg (dimethyl sulfide). Although these detection limit values improved gradually with decreasing injection volume, the minimum detectable concentration (e.g., in nmol mol⁻¹ scale) remained constant due to a balance by the sample volume reduction. The linearity property of pulsed flame photometric detector also appeared to vary dynamically with changes in its sensitivity. According to this study, the performance of pulsed flame photometric detector, when tested by direct injection method, is highly reliable to precisely describe the behavior of reduced sulfur compounds above ∼20 nmol mol⁻¹.     

Trace determination of volatile sulfur compounds by solid-phase microextraction and GC-MS

A method was developed for the simultaneous determination of the following nine volatile sulfur compounds in gas samples: carbon disulfide, carbonyl sulfide, ethyl sulfide, ethyl methyl sulfide, hydrogen sulfide, isopropanethiol, methanethiol, methyl disulfide and methyl sulfide. The target compounds were preconcentrated by solid-phase microextraction (SPME) and determined by gas chromatography combined with mass spectrometry. Experimental design was employed to optimize the extraction time and temperature and concurrent detection of the nine compounds was achieved by using an SPME fiber coated with Carboxen-polydimethylsiloxane (75 microns). Detection limits ranged from 1 ppt (v/v) for carbon disulfide to 350 ppt (v/v) for hydrogen sulfide and calibration functions were linear up to 20 ppb (v/v) for all the compounds investigated.     

固相微萃取-气相色谱/同位素质谱法测定水中挥发性有机物单体碳同位素

建立了采用75μm碳分子筛/聚二甲基硅氧烷(CAR-PDMS)纤维的固相微萃取-气相色谱/同位素质谱联用方法测定水中挥发性有机污染物碳同位素。使用浸入式固相微萃取和顶空固相微萃取方法进行实验确定在低浓度条件下最佳δ13C测试方法。通过使用顶空固相微萃取前处理技术进行单体同位素分析分析灵敏度更高,应用CSIA技术对1,2-二氯乙烯,三氯乙烯,四氯化碳进行单体同位素分析,方法的检出限为70μg/L,与样本的标准偏差小于0.3‰。该法适用于水体中微量挥发性有机污染物的同位素组成测定。     

Quantification of volatile sulfur compounds in complex gaseous matrices by solid-phase microextraction

Procedures were assessed for quantifying nine volatile sulfur compounds found in complex gaseous samples collected at a biogas-production plant and a sewage treatment plant. The target compounds were extracted by solid-phase microextraction (using the 75-microm Carboxen-polydimethylsiloxane fiber coating) at 22 degrees C for 20 min, and analyzed by GC-MS. Detection limits ranged between 1 pptv (v/v) for carbon disulfide and 470 pptv (v/v) for hydrogen sulfide. High amounts of organic compounds were found during full-scan analysis of the samples and standard additions to individual sub-samples revealed that the analysis was subject to matrix effects. However, the functions obtained by standard additions were still linear and quantification was possible for all the compounds tested except hydrogen sulfide. No detectable losses were observed during storage in the sampling containers, made of Tedlar film, over a storage period of 20 h. However, water permeated through the walls and the relative humidity in the bag increased during storage until it reached the ambient level. Finally, it was shown that the drying agent, CaCl2, caused no detectable losses of any of the compounds.     

Plasma Reaction Behaviors of Carbon Disulfide and Carbon Dioxide in Glow Discharges

Reaction behaviors of carbon disulfide and carbon dioxide in plasma were investigated and compared. It was found that carbon disulfide is very reactive in plasma to produce dark brown filmy polymers, but carbon dioxide does not give polymeric products at all. The difference in plasma behaviors of the two monomers can be attributed to the roles of sulfur and oxygen in the monomers. There is also some discussion on the spectro-scopic data of carbon disulfide polymers.     

热脱附-气相色谱-质谱法测定环境空气中67种挥发性有机物

采用热脱附-气相色谱-质谱法,建立了同时分析环境空气中67种挥发性有机物的分析方法。对比了5种不同填充材料不锈钢吸附管对78种挥发性有机物的吸附能力。填充材料为Tenax TA和Carbograph 1TD的混合填料吸附管对分析物的捕集效果最好,在30 mL/min高纯He气持续吹脱45 min的情况下,未发生穿透（即穿透率小于10%）的化合物达67种,分析物的种类包括芳香烃、脂肪烃、卤代烃和含氧挥发性有机物等。优化了使用该吸附管测定67种目标物时的热脱附条件。在5~100 ng范围内,目标化合物的色谱响应值与其量间具有良好的线性关系,其相关系数（r）均在1.0000~0.9977之间。方法检出限为0.3~2.4 ng,以采样体积1 L计算,检出限为0.3~2.4 μg/m³。加标量为20 ng时,7次重复实验目标化合物回收率均在81.6%~114.9%之间,目标化合物的相对标准偏差为1.2%~10.1%。采用该方法对某车厢内空气进行了检测,检出了包括酯类、卤代烷烃、卤代烯烃以及芳香族化合物在内的19种目标化合物,其范围为1.1~84.1 μg/m³。该方法准确、可靠、灵敏度高,实现了对环境空气中67种目标污染物的准确定量。     

Volatile organic compounds of Angelica gigas Nakai, Korean medicinal herb

The study was performed to find out the profile of volatile flavor components from the aromatic medicinal plant, Angelica gigas Nakai. The volatile organic compounds of A. gigas Nakai were extracted by simultaneous steam distillation and extraction (SDE) method, and identified by gas chromatograph/mass spectrometric (GC/MS) analysis. A total of 116 compounds, including 40 hydrocarbons, 37 alcohols, 15 esters, 12 aldehydes, 7 ketones, and 5 miscellaneous were identified and quantified. Among them, 75 volatile organic compounds were detected which make up 90.52% of total volatile content. alpha-Pinene was detected as the prime volatile component which accounted for 30.89% of total volatile content and 2,4,6-trimethyl heptane, camphene, alpha-limonene, beta-eudesmol, vervenol, alpha-murrolene, and sphatulenol were detected as the major components of A. gigas Nakai.     

Sampling and Analysis of Odorous Compounds in Water Treatment Plants

Abstract

The following analytical method has been used to identify some odorous compounds in the air of the water treatment plant Werdholzli, Zurich: sampling of contaminated air with the help of activated carbon, desorption by the solvents carbon disulphide and methylene chloride, separation of the carbon disulfide extract into a polar and a nonpolar fraction by adsorption column chromatography on silica. Hereafter gaschromatographic analysis of the polar fraction on glass capillary column (Ucon HB 5100); detection and identification were achieved by flame ionisation, thermoionic nitrogen selective detector and computerized mass spectrometry (Finnigan 3200 F, data system 6110).

The results show the presence of sulfur compounds: thiophenes, thiazoles; nitrogen compounds: pyrazines; oxygen compounds: phenols, alcohols and some unsatured hydrocarbons. The malodorous compounds were sulfur and nitrogen compounds in the range of 0.01-0.1 ppm.