多氢键反应-纳米金共振散射光谱法测定三聚氰胺

在pH 7.0的磷酸盐缓冲溶液中,氯金酸被3,5-二羟基苯甲酸(DBA)还原生成的金纳米粒子在610nm处产生一个较强的共振散射峰;当有三聚氰胺(MA)存在时,DBA与MA形成多氢键化合物而不能还原氯金酸,导致610 nm处共振散射峰的强度降低.三聚氰胺的浓度在5.0×10 -6～4.0×10-5 mol·L-1范围内...     

酸水解-离子色谱法测定精四氯化钛中三氯乙酰氯

建立了酸水解-离子色谱法测定精四氯化钛中痕量三氯乙酰氯(CCl3COCl)的方法.四氯化钛样品与2 mol/L HCl按体积比1∶4水解平衡后,采用氢氧化物共沉淀法去除溶液中Ti4+,V5+和Fe3+等金属离子,用Ag2O沉淀法降低水解溶液中Cl-浓度,水解溶液通过H型阳离子交换柱和水系滤膜,离子色谱法测定溶液中三氯乙酸(TCAA),据TCAA与CCl3COCl摩尔量守恒计算样品中CCl3COCl含量.结果表明,共沉淀溶液pH值在9.0～10.0范围内,可将目标金属离子基本去除完全;加入Ag2O降低溶液Cl-浓度后,溶液中Cl-,NO3-和SO42-的浓度对水解溶液中TCAA的色谱法峰无影响.本方法对精四氯化钛样品中CCl3COCl的定量限为1.20 μg/g,低于俄罗斯精四氯化钛中CCl3COCl允许限值(5μg/g);方法加标回收率在84.1％ ～87.3％之间,共沉淀时溶液pH值的轻微变化对回收率无明显影响,分析结果稳定可靠;方法用于5个平行样品中CCl3COCl含量测定(45.6,37.9,40.8,38.9和43.5 μg/g),相对标准偏差7.7％,方法精密度较好.方法满足精四氯化钛中CCl3COCl质量控制要求.     

金(Ⅲ)-meso-四(4-乙酰氧基苯)卟啉-十二烷基硫酸钠-TritonX-100显色反应的研究

本文研究了在适量镉和混合表面活性剂存在下,meso-四(4-乙酰氧基苯)卟啉[T(4-AOP)P]与Au(Ⅲ)的显色反应。结果表明,在pH10.0～11.2介质中,Au(Ⅲ)与T(4-AOP)P形成了灵敏度很高的稳定络合物,其摩尔吸光系数ε_(420nm)=1.62×10~6L·mol~(-1)。cm~(-1),金(Ⅲ)浓度在0～1.2μg/10ml范围内服从比耳定律。络合物中的摩尔比为Au(Ⅲ):T(4-AOP)P=1:1。用泡沫塑料预分离富集金;将拟定的新方法应用于岩矿中金的测定,得到较为满意的结果。     

氯化介质中PbS固体表面的氯络合-溶解行为

对硫化铅固体表面的氯络合-溶解行为进行了研究。溶液化学计算考察颗粒表面固体反应产物(PbCl2)的生成与溶解情况表明,饱和氯化钠介质中PbCl2主要以[PbCl4]2-络合物的形式存在于溶液中,氯离子组分总浓度[Cl-]T=0·918mol/L时,PbCl2能较好地呈固态晶体析出,[Cl-]T>0·918mol/L时PbCl2晶粒因氯络合作用而溶解。通过Tafel实验进一步分析了PbS固体表面的腐蚀溶解行为,结果显示,当CFe3 ≤6×10-4mol/L时,腐蚀速度对Fe3 存在很强的依数性,浓度增加,腐蚀速度快速提高;CFe3 >6×10-4mol/L,有钝化现象发生。NaCl的加入,溶液相Cl-活度增加,PbCl2快速溶解,腐蚀反应加快。     

2-羟基-3-(三乙胺基)丙基正癸基硫醚修饰碳糊电极测定痕量金

制备了2＿羟基＿3＿(三乙胺基)丙基正癸基硫醚修饰碳糊电极,用于痕量金的测定。研究了电极的伏安特性及分析条件。在0.2mo／LKCl-HCl缓冲溶液中(pH1),Au(Ⅲ)被富集到电极表面,然后介质交换到0.2mol／LKCl-HCl空白溶液中(pH1)进行阳极溶出伏安测定,对于5min富集,Au(Ⅲ)浓度在2×10-8～1×10-6mol／L范围内呈线性关系,检出限为1×10-8mol／L,相对标准偏差5.2%,一般常见离子不干扰。     

配制铜盐、铁盐和铝盐水溶液是因水解而显浑浊吗

正1问题的提出文献[1]:硫酸铜的水溶液由于Cu2+水解而显酸性,其水解度随浓度降低而增加,288K时,0.1mol/L CuSO4溶液的pH=4.2,所以配制铜盐时,常加入少量同名的酸。文献[2][3]:在实验室配制FeCl3溶液时,由于FeCl3是强酸弱碱生成的盐,容易水解生成难溶于水的Fe(OH)3:FeCl3+3H2O=Fe(OH)3+3HCl致使溶液浑浊,得不到澄清的FeCl3溶液。所     

Cr~(3 )的水解聚合作用 Ⅵ.反丁烯二酸存在下低浓度铬的水解聚合

铬(Ⅲ)离子与反丁烯二酸生成的羟联多核配合物可用作偶联剂,但其在溶液中的状态尚缺乏定量研究。本文用静置平衡pH法在四种不同浓度(0.00175,0.0025,0.00375和0.005mol·dm~(-3))的反丁烯二酸存在下和低铬浓度(0.0025mol·dm~(-3))时,研究了C~(3 )在溶液中的状态,并用Newton-Raphson法和非线性最小平方法计算了在四种反丁烯二酸浓度下[Cr_2OH]~(5 ),[Cr_2(OH)A]~(3 )和[Cr_2(OH)A_2]~ 的水解常数和形成常数,在四种浓度下所得结果颇为一致。本文的结果对合成偶联剂和解释偶联作用的机理提供了线索。     

某些Au(III)、Au(I)配离子在溶液中扩散的研究

用毛细管色谱在25℃测定了AuCl4、[Au(SO3)2]、[Au(CSN2H4)2]、[Au(CN)2]等配位体离子在HCl溶液中的扩散系数及AuCl4阴离子的扩散活化能, 并与文献中其它配阴离子的D值比较, 认为扩散离子的质量和所载电荷可能是决定配阴离子扩散系数的主要因素.     

基于Au/SiO2纳米粒子的结晶紫表面增强拉曼特性研究

采用自组装-化学镀法制备了以SiO2为核,Au为壳层的核壳结构纳米粒子(Au/SiO2),以生物染色剂结晶紫为探针分子,研究了Au/SiO2的表面增强拉曼散射(SERS)效应,并考察了Cl-对SERS增强效应的影响。实验表明,Cl-对SERS有明显的增强效果,这主要是由于Cl-的加入使得Au/SiO2发生团聚,产生大量"热点",从而使SERS增强效果进一步加强。以Au/SiO2(5×1010 mL-1)为活性基底,KCl(0.01 mol/L)为额外增强剂,在水溶液中实现了对结晶紫(CV)的痕量检出,最低检测浓度可达到5×10-10mol/L。     

AuClx (x=1, 3)催化2-炔丙基苯酮与苯炔环化反应机理

对金属元素Au采用LanL2DZ基组,对非金属元素C,H,O,Cl采用6-31G*和6-311++G**基组,用密度泛函理论的B3LYP、B3PW91、UB3LYP方法和二阶微扰理论MP2方法研究了不同氧化态的金催化剂催化2-炔丙基苯酮与苯炔环化反应的机理.结果表明:在AuCl和AuCl3的作用下,反应均能通过[4+2]和[3+2]途径生成产物.但在AuCl催化下,[4+2]反应途径比[3+2]反应途径具有更低的活化自由能,反应主要通过[4+2]途径进行;而在AuCl3催化下,[4+2]反应途径与[3+2]反应途径的活化自由能相近,反应通过两条途径竞争生成产物.比较AuCl和AuCl3的催化效果发现,不同氧化态的金催化剂改变了反应的机理,该反应的活化自由能在AuCl作用下比在AuCl3作用下低11.18 kJ·mol-1.对于该反应,AuCl表现出了更好的催化活性.这些计算结果和实验现象相吻合.     

Gold complexes with potentially tri- and tetradentate phosphinothiolate ligands

Reactions of [Au(PPh3)Cl], (Bu4N)[AuCl4] and the organometallic gold complex [Au(damp-C1,N)Cl2] (damp- = 2-(N,N-dimethylaminomethyl)phenyl) with the potentially tri- and tetradentate proligands PhP(C6H3-SH-2-R-3)2 (H2L1a, R = SiMe3; H2L1b, R = H) and P(C6H4-SH-2)3 (H3L2) result in the formation of mono- or dinuclear gold complexes depending on the precursor used. Monomeric complexes of the type [AuL1Cl] are formed upon the reaction with [Au(damp-C1,N)Cl2], but small amounts of dinuclear [AuL1]2 complexes with gold in two different oxidation states, +1 and +3, have been isolated as side-products. The dinuclear compounds are obtained in better yields from [AuCl4]-. A dinuclear complex having two Au(III) centers can be isolated from the reaction of [Au(PPh3)Cl] with H3L2, whereas from the reaction with H2L1b the mononuclear [Au(Ph3P)HL1b] is obtained, which contains a three-coordinate gold atom. Comparatively short gold-gold distances have been found in the dinuclear complexes (2.978(2) and 3.434(1) A). They are indicative of weak gold-gold interactions, which is unusual for gold(III).     

Unprecedented formation of novel phosphonodithioate ligands from diferrocenyldithiadiphosphetane disulfide

The reaction of the phosphetane disulfide, FcP(S)S 2P(S)Fc ( 1) (Fc = (eta (5)-C 5H 5)Fe(eta (5)-C 5H 4)), the ferrocenyl analogue of the Lawesson reagent, with gold and palladium complexes leads to the unprecedented formation of phosphonodithioate ligands upon coordination to the metal centers. The reaction of 1 with gold complexes such as [AuCl(PR 3)] affords the species [Au{S 2P(OH)Fc}(PR 3)] (PR 3 = PPh 3 ( 2), PPh 2Me ( 3)), in which the phosphonodithioate ligand Fc(OH)PS 2 (-) has been formed. The same ligand is present in the compound [Au 2{S 2P(OH)Fc} 2].[N(PPh 3) 2]Cl ( 4), obtained by reaction of 1 with [N(PPh 3) 2][AuCl 2]. It crystallizes with one molecule of [N(PPh 3) 2]Cl, whereby complex 4 acts as an anion receptor and forms strong hydrogen bonds between the chloro and the hydroxyl groups. The reaction with palladium derivatives is different; two complexes, [Pd 2(S 4OP 2Fc 2) 2] ( 5) and [Pd 4Cl 4(S 4OP 2Fc 2) 2] ( 6), are obtained in molar ratio 2:1 and 1:1, respectively. In these complexes a new phosphonodithioate ligand is present and probably arises from the condensation of two molecules of Fc(OH)PS 2 (-). Complex 5 has also been characterized by X-ray methods.     

TiO_2/Na_2SO_3体系中日光催化聚合甲基丙烯酸甲酯的研究

在密闭空气和日光连续照射下 ,考察了TiO2 Na2 SO3 体系中MMA的聚合行为 ,结果显示 ,在TiO2 的零电荷点处 ,日光可引发聚合甲基丙烯酸甲酯 ,诱导期为 2～ 15min ,主要受pH的控制 .当 [TiO2 ]=(5 .0～ 7.0 )× 10 - 5mol·L- 1 ,[Na2 SO3]=(1.0～ 1.5 6 )× 10 - 3 mol·L- 1 ,[MMA]=(3.74～ 10 .7)× 10 - 2 mol·L- 1 时 ,表观聚合速率Rp=k·e- 1 1 4 .80 0 RT·[MMA]0 .94[IA]0 .50 [Na2 SO3]0 .55[TiO2 ]1 .0 6 ,所得聚合物平均分子量为 12 0× 10 5,最高产率达 95 % ,聚合按自由基机理进行     

EXAFS study of aqueous Zr(IV) and Th(IV) complexes in alkaline CaCl(2) solutions: Ca(3)[Zr(OH)(6)](4+) and Ca(4)[Th(OH)(8)](4+)

A hitherto unknown type of aqueous complex, ternary Ca-MIV-OH complexes (M = Zr and Th), causes unexpectedly high solubilities of zirconium(IV) and thorium(IV) hydrous oxides in alkaline CaCl2 solutions (pHc = 10-12, [CaCl2] > 0.05 mol.L(-1), and pHc = 11-12, [CaCl2] > 0.5 mol.L(-1), respectively). The dominant aqueous species are identified as Ca3[Zr(OH)6]4+ and Ca4[Th(OH)8]4+ and characterized by extended X-ray absorption fine structure (EXAFS) spectroscopy. The number of OH- ligands in the first coordination sphere detected by EXAFS, NO = 6 (6.6 +/- 1.2) for Zr and NO = 8 (8.6 +/- 1.2) for Th, are consistent with the observed slopes of 2 and 4 in the solubility curves log [M]tot vs pHc. The presence of polynuclear hydrolysis species and the formation of chloride complexes can be excluded. EXAFS spectra clearly show a second coordination shell of calcium ions. The [Zr(OH)6]2- and [Th(OH)8]4- complexes with an unusually large number of OH- ligands are stabilized by the formation of associates or ion pairs with Ca2+ ions. The number of neighboring Ca2+ ions around the [Zr(OH)6]2- and [Th(OH)8]4- units is determined to be NCa = 3 (2.7 +/- 0.6) at a distance of RZr-Ca = 3.38 +/- 0.02 A and NCa = 4 (3.8 +/- 0.5) at a distance of RTh-Ca = 3.98 +/- 0.02 A. The Ca3[Zr(OH)6]4+ and Ca4[Th(OH)8]4+ complexes have first (M-O) and second (M-Ca) coordination spheres with the Ca2+ ions bound to coordination polyhedra edges.     

Size control of gold nanocrystals in citrate reduction: the third role of citrate

Growth kinetics and temporal size/shape evolution of gold nanocrystals by citrate reduction in boiling water were studied systematically and quantitatively. Results reveal that the size variation and overall reaction mechanism were mostly determined by the solution pH that was in turn controlled by the concentration of sodium citrate (Na3Ct) in the traditional Frens's synthesis. This conclusion was further confirmed by the reactions with variable pH but fixed concentrations of the two reactants, HAuCl4 and Na3Ct. Two substantially different reaction pathways were identified, with the switching point at pH = 6.2-6.5. The first pathway is for the low pH range and consists of three overlapping steps: nucleation, random attachment to polycrystalline nanowires, and smoothing of the nanowires via intra-particle ripening to dots. The second pathway that occurred above the pH switching point is consistent with the commonly known nucleation-growth route. Using the second pathway, we demonstrated a new synthetic route for the synthesis of nearly monodisperse gold nanocrystals in the size range from 20 to 40 nm by simply varying the solution pH with fixed concentrations of HAuCl4 and Na3Ct. The switching of the reaction pathways is likely due to the integration nature of water as a reaction medium. In the citrate reduction, the solution pH was varied by changing the initial HAuCl4/Na3Ct ratio. Consequently, when pH was higher than about 6.2, the very reactive [AuCl3(OH)]- would be converted to less reactive [AuCl2(OH)2]- and [AuCl(OH)3]-.     

Structural, photophysical, and catalytic properties of Au(I) complexes with 4-substituted pyridines

Ionic gold(I) complexes with general formula of [Au(Py)2][AuCl2] and [Au(Py)2][PF6] (Py = 4-substituted pyridines) have been synthesized. Structures of five Au(I) complexes and a Ag(I) complex were determined by single crystal X-ray diffraction. Evidence for cationic aggregation of [Au(py)2][PF6] complexes in solution was obtained by conductivity measurements and by the isosbestic point observed from variable temperature UV-visible absorption spectra. All compounds were luminous in the solid state. Calculations employing density functional theory were performed to shed light on the nature of the electronic transitions. While the [Au(4-dmapy)2][AuCl2] (4-dmapy = 4-dimethylaminopyridine) and [Au(4-pic)2][AuCl2] (4-pic = 4-picoline) emissions were found to be mainly ligand in nature, their [PF6](-) counterparts involved a Au...Au-interaction imbedded in the highest occupied molecular orbital. [Au(4-dmapy)2][AuCl2] was found to be an efficient catalyst for Suzuki cross-coupling of aryl bromide and phenylboronic acid.     

Neutral gold complexes with tridentate SNS thiosemicarbazide ligands

Na[AuCl(4)]·2H(2)O reacts with tridentate thiosemicarbazide ligands, H(2)L1, derived from N-[N',N'-dialkylamino(thiocarbonyl)]benzimidoyl chloride and thiosemicarbazides under formation of air-stable, green [AuCl(L1)] complexes. The organic ligands coordinate in a planar SNS coordination mode. Small amounts of gold(I) complexes of the composition [AuCl(L3)] are formed as side-products, where L3 is an S-bonded 5-diethylamino-3-phenyl-1-thiocarbamoyl-1,2,4-triazole. The formation of the triazole L3 can be explained by the oxidation of H(2)L1 to an intermediate thiatriazine L2 by Au(3+), followed by a desulfurization reaction with ring contraction. The chloro ligands in the [AuCl(L1)] complexes can readily be replaced by other monoanionic ligands such as SCN(-) or CN(-) giving [Au(SCN)(L1)] or [Au(CN)(L1)] complexes. The complexes described in this paper represent the first examples of fully characterized neutral Gold(III) thiosemicarbazone complexes. All the [AuCl(L1)] compounds present a remarkable cell growth inhibition against human MCF-7 breast cancer cells. However, systematic variation of the alkyl groups in the N(4)-position of the thiosemicarbazone building blocks as well as the replacement of the chloride by thiocyanate ligands do not considerably influence the biological activity. On the other hand, the reduction of Au(III) to Au(I) leads to a considerable decrease of the cytotoxicity.     

The first acetimine gold(I) and gold(III) complexes and the first acetonine complexes

Ketimino(phosphino)gold(I) complexes of the type [Au[NR=C(Me)R']L]X (X = ClO4, R = H, L = PPh3, R'=Me (la), Et (2a); L=PAr3 (Ar=C6H4OMe-4), R'=Me (1b), Et (2b); L=PPh3, R=R'=Me (3); X= CF3SO3 (OTf), L=PPh3, R=R'=Me (3'); R=Ar, R'=Me (4)) have been prepared from [Au(acac)L] (acac = acetyl acetonate) and ammonium salts [RNH3]X dissolved in the appropriate ketone MeC(O)R'. Complexes [Au(NH=CMe2)2]X (X = C1O4 (6), OTf (6')) were obtained from solutions of [Au(NH3)2]X in acetone. The reaction of 6 with PPN[AuCl2] or with PhICl2 gave [AuCl(NH=CMe2)] (7) or [AuCI2(NH=CMe2)2]ClO4 (8), respectively. Complex 7 was oxidized with PhICl2 to give [AuCl3(NH=CMe2)] (9). The reaction of [AuCl(tht)] (tht = tetrahydrothiophene), NaClO4, and ammonia in acetone gave [Au(acetonine)2]ClO4 (10) (acetonine = 2,2,4,4,6-pentamethyl-2,3,4,5-tetrahydropyrimidine) which reacted with PPh3 or with PPN[AuCl2] to give [Au(PPh3)(acetonine)]ClO4 (11) or [AuCl(acetonine)] (12), respectively. Complex 11 reacts with [Au(PPh3)(Me2CO)]ClO4 to give [(AuPPh3)2(mu-acetonine)](ClO4)2 (13). The reaction of AgClO4 with acetonine gave [Ag(acetonine)(OClO3)] (14). The crystal structures of [Au(NH2Ar)(PPh3)]OTf (5), 6' and 10 have been determined.     

Gas-phase experiments on Au(III) photochemistry

Irradiation of AuCl(4)(-) and AuCl(2)(OH)(2)(-) in the gas-phase using ultraviolet light (220-415 nm) leads to their dissociation. Observed fragment ions for AuCl(4)(-) are AuCl(3)(-) and AuCl(2)(-) and for AuCl(2)(OH)(2)(-) are AuCl(2)(-) and AuClOH(-). All fragment channels correspond to photoreduction of the gold atom to either Au(II) or Au(I) depending on the number of neutral ligands lost. Fragment branching ratios of AuCl(4)(-) are observed to be highly energy dependent and can be explained by comparison of the experimental data to calculated threshold energies obtained using density functional theory. The main observed spectral features are attributed to ligand-to-metal charge transfer transitions. These results are discussed in the context of the molecular-level mechanisms of Au(III) photochemistry.