Comparison of different immunoaffinity clean-up procedures for high-performance liquid chromatographic analysis of ochratoxin A in wines

Three immunoaffinity clean-up procedures to analyse ochratoxin A (OTA) in wines were compared. The direct wine clean-up with Ochraprep and OchraTest columns gave equivalent results in terms of recovery and precision if compared with the reference procedure involving a preliminary extraction of OTA with chloroform. OTA quantification limit in wine ranged from 0.020 to 0.045 microg/l. The 'on-flow' OTA emission spectrum (excitation 333 nm) showed a maximum at 460 nm and could be used to confirm the quantitative results. The analysis of 11 red and white wines gave no significant quantitative differences between the three clean-up techniques.     

Determination of ochratoxin A in wine using liquid-phase microextraction combined with liquid chromatography with fluorescence detection

A liquid-liquid microextraction technique (LPME) has been applied to the extraction of ochratoxin A (OTA) from wine prior to its quantification by HPLC-fluorescence detection. OTA was extracted from wine, through 1-octanol immobilized in the pores of a porous hollow fiber, and introduced into 1-octanol inside the fiber. Recovery was 77%. The method was adequate for quantification of OTA in wine at levels within the range 0.25-10 ng/ml with a LOD of 0.2 ng/ml, and can be a simple and inexpensive alternative to the use of inmunoaffinity columns in order to quantify OTA levels in wine.     

Natural occurrence of ochratoxin A in dried figs

Ochratoxin A (OTA) contamination in dried figs was investigated using high performance liquid chromatography (HPLC) with fluorescence detection after extraction with methanol and orthophosphoric acid and clean up by an immunoaffinity column. The limit of detection for OTA was 0.12 microg kg(-1). One hundred and fifteen samples were taken during the drying stage from 7 different districts in the Aegean Region in 2003 and 2004. Fifty-five (47.2%) of the 115 samples were found to contain detectable levels of ochratoxin A, ranging from 0.12 to 15.31 microg kg(-1). However, the OTA level for a majority of the samples was low, with only 4 samples containing OTA exceeding 1 microg kg(-1). The calculated overall median for the OTA level was below the limit of detection and the overall mean was estimated as 0.52 microg kg(-1). Frequency of ochratoxin A contamination in dried figs harvested in 2003 and 2004 are 47 and 50%, respectively. Highest contamination ratio was determined in dried figs from Erbeyli (60%), followed by Selcuk (56%), and Ortaklar (50%).     

Coacervative extraction of Ochratoxin A in wines prior to liquid chromatography/fluorescence determination

Coacervates made up of reverse micelles of decanoic acid were assessed as a new strategy for the simplification of wine sample treatment in the determination of Ochratoxin A (OTA). Simultaneous extraction/concentration of this contaminant was based on both hydrophobic and hydrogen bond OTA:coacervate interactions. Parameters affecting extraction efficiency and concentration factors were studied. Concentrations of decanoic acid and tetrahydrofuran (THF) were the most influential parameters, being 0.5% of acid and 5% of THF the selected ones. The procedure was very robust, so that the extractions were not influenced by the pH and the nature or concentration of matrix components. OTA recoveries from different types of wines (white, rosé and red) ranged between 85 and 100% and the actual concentration factors varied from 105 to 125 for sample volumes of 15 mL. The detection limits for OTA, after liquid chromatography/fluorimetry (LC/FL) analysis of the coacervate (20 microL), were 4.5 ng L(-1) in white and rosé wines and 15 ng L(-1) in red wines, values which were far below the threshold limit established for OTA by EU directives (2.0 microg L(-1)). No clean-up of the extracts was required for any of the samples analysed. The overall sample treatment took about 15-20 min and several samples could be simultaneously treated using conventional lab equipment. The precision of the method, expressed as relative standard deviation, was about 5%. The approach developed was successfully applied to the determination of OTA in different wine samples from the South of Spain. The concentrations found ranged between 0.015 and 0.091 microg L(-1).     

Quantitative determination of sotolon, maltol and free furaneol in wine by solid-phase extraction and gas chromatography-ion-trap mass spectrometry

A method for the analytical determination of sotolon [4,5-dimethyl-3-hydroxy-2(5H)-furanone], maltol [3-hydroxy-2-methyl-4H-pyran-4-one] and free furaneol [2,5-dimethyl-4-hydroxy-3(2H)-furanone] in wine has been developed. The analytes are extracted from 50 ml of wine in a solid-phase extraction cartridge filled with 800 mg of LiChrolut EN resins. Interferences are removed with 15 ml of a pentane-dichloromethane (20:1) solution, and analytes are recovered with 6 ml of dichloromethane. The extract is concentrated up to 0.1 ml and analyzed by GC-ion trap MS. Maltol and sotolon were determined by selected ion storage of ions in the m/z ranges 120-153 and 79-95, using the ions m/z 126 and 83 for quantitation, respectively. Furaneol was determined by non-resonant fragmentation of the m/z 128 mother ion and subsequent analysis of the m/z 81 ion. The detection limits of the method are in all cases between 0.5 and 1 microg l(-1), well below the olfactory thresholds of the compounds. The precision of the method is in the 4-5% range for levels in wine around 20 microg l(-1). Linearity holds at least up to 400 microg l(-1), and is satisfactory in all cases. The recoveries of maltol and sotolon are constant (70 and 64%, respectively) and do not depend on the type of wine. On the contrary, in the case of furaneol, red wines show constant and high recoveries (97%), while the recoveries on white wines range between 30 and 80%. Different experiments showed that this behavior is probably due to the existence of complexes formed between furaneol and sulphur dioxide or catechols. Sensory experiments confirmed that the complexed forms found in white wines are not perceived by orthonasal olfaction, and that the furaneol determined by the method can be considered as the free and odor-active fraction.     

Comparison of different sample treatments for the analysis of ochratoxin A in must, wine and beer by liquid chromatography

Ochratoxin A (OTA) is a mycotoxin produced by some species of Aspergillus and Penicillium verrucosum. It has been found in foods and feed all over the world. There is a great concern about OTA because it is nephrotoxic and probably, carcinogenic to humans. Most of analytical methods developed for OTA in wine, beer and other products are based on LC with fluorescence detection (LC-FLD). In the present work, various procedures for extraction and/or clean-up for determination of OTA in musts, wine and beer by LC-FLD were compared: (1) dilution with polyethylen glycol 8000 and NaHCO3 solution and clean-up an on immunoaffinity column (IAC); (2) extraction with chloroform and IAC clean-up; solid-phase extraction (SPE) on (3) reversed-phase (RP) C18; (4) RP phenylsilane and (5) Oasis HLB cartridges. SPE on phenylsilane and Oasis HLB have not been reported for OTA analysis in beverages. The same LC-FLD conditions and concentration ratio were used. The former procedure was simple, rapid and provided flat baselines, free from most impurity peaks, high OTA recoveries and quite repeatable results. RP C18 using methanol-acetic acid (99.5:0.5) as elution solvent provided good recoveries and precision, thus becoming a cheaper but interesting alternative at 0.1-1 ng/ml spiking levels. Oasis HLB cartridges were usually better than phenylsilane. Possible binding of OTA to proteins or other components was tested by acid treatment before extraction but no significant differences with controls appeared.     

免疫亲和柱净化-柱后光化学衍生-高效液相色谱法同时检测粮谷中的黄曲霉毒素、玉米赤霉烯酮和赭曲霉毒素A

建立了同时检测粮谷中黄曲霉毒素(B1、B2、G1和G2)、玉米赤霉烯酮和赭曲霉毒素A的免疫亲和柱净化-柱后光化学衍生-高效液相色谱方法。样品经过甲醇-水(体积比为80∶20)提取,通过免疫亲和柱富集和净化,采用Waters Nova-Pak色谱柱(3.9 mm i.d.×150 mm,4 μm),以甲醇、乙腈和1%的磷酸溶液为流动相,梯度洗脱,柱后光化学衍生、改变波长荧光检测。黄曲霉毒素(B1、B2、G1和G2)、玉米赤霉烯酮和赭曲霉毒素A检出限分别为0.24,4.0和0.5 μg/kg,标准曲线的线性范围分别为0.24~6.0,4.0~100.0和0.5~40.0 μg/L;在小麦、玉米、黑麦样品中,平均加标回收率为70.8% ~94.0%,相对标准偏差为2.79% ~9.38%。     

Molecularly imprinted solid-phase extraction method for the high-performance liquid chromatographic analysis of fungicide pyrimethanil in wine

A method for molecularly imprinted solid-phase extraction (MISPE) of the fungicide pyrimethanil from wine samples has been investigated. The molecular imprinted polymer was obtained by iniferter-mediated grafting on porous chloromethylated polystyrene beads, using methacrylic acid as the functional monomer and ethylene glycol dimethacrylate as the cross-linker. The imprinted beads were evaluated for use as a solid-phase extraction sorbent, in order to develop the extraction protocol in aqueous standards and red wine samples. The optimised extraction protocol resulted in a reliable MISPE method suitable for HPLC analysis (stationary phase: Cromolith Performance C18 column, 100 mm x 4.6 mm; mobile phase: acetonitrile-water (3:2, v/v), flow-rate: 1.00 ml/min; detection 270 nm). It was selective for pyrimethanil and the related pyrimidinic fungicides cyprodinil and mepanipyrim, while the non-pyrimidinic fungicides benalaxyl, chlozolinate, furalaxyl, iprodione, metalaxyl, nuarimol, procymidone and vinclozolin were not extracted. Recoveries performed on a wine matrix spiked with pyrimethanil at three different concentration levels were reproducible and were in good agreement with the recoveries performed on buffer, coming out between 80 and 90% (85+/-7.0% at 0.50 microg/ml, 79+/-1.6% at 2.0 microg/ml and 87+/-5.6% at 20 microg/ml). Preconcentration and quantitative extraction of pyrimethanil from wine samples was shown to be feasible down to 0.1 microg/ml.     

Determination of zearalenone and ochratoxin A in soil

Mycotoxins are secondary metabolites, formed by the action of fungi on agricultural crops in the field or during storage. These metabolites are highly toxic to animals and humans and high levels have been measured in agricultural crops. In order to evaluate human risks due to ingestion of mycotoxin-contaminated food different methods have been developed for analysis of mycotoxins in cereals and maize. In this project the focus was on mycotoxins in agricultural soil and the fate of these toxins in the soil-water-plant system. Two different mycotoxins were selected in the study: zearalenone (ZON) produced by species of Fusariumor Aspergillusand ochratoxin A (OTA) produced by species of Penicillium. We developed a method for analysis of these toxins in soil. Soil samples were extracted with methanol-water (9:1) and purified by solid-phase extraction (SPE, C8-columns). The final extract was analysed using high-pressure liquid chromatography (HPLC) with fluorescence detection. A Phenyl Hexyl column was used to separate the toxins. The detection limits obtained were 0.1 and 1.0 microg kg(-1) dry weight (dw) for OTA and ZON, respectively. The developed method has been used for analysis of different soils in connection with growth chamber experiments. The soil types used in the growth chamber experiments were a sandy soil, a sandy clay soil, and a soil with high content of organic matter. The recovery was determined as 85.8 and 93.4% and the repeatability to 5.1 and 12.8% for OTA and ZON, respectively. The reproducibility obtained was 8.5 and 15.0% for soil samples, representing concentration levels from 0.2-30 microg kg(-1) dw (OTA) and from 1.0-100 microg kg(-1) dw (ZON).     

Simultaneous determination of aflatoxins, ochratoxin A, and zearalenone in grains by new immunoaffinity column/liquid chromatography

The simultaneous determination of mycotoxins was performed in 3 steps: extraction, cleanup, and detection. For extraction, a mixture of acetonitrile-water (60 + 40, v/v) was proved appropriate. For cleanup, a new Afla-Ochra-Zea immunoaffinity column was used. After derivatization with trifluoroacetic acid, the mycotoxins aflatoxins, ochratoxin A (OTA), and zearalenone (ZEA) were determined simultaneously by liquid chromatography with fluorescence detection. The detection limits in different matrixes after cleanup with the new immunoaffinity column were very low: aflatoxins, 0.002-0.7 microg/kg; OTA, 0.07-0.25 microg/kg; ZEA, 1-3 microg/kg. The limits of determination were: aflatoxins, 0.25 microg/kg; OTA, 0.5 microg/kg; ZEA, 5 microg/kg. The recovery rates for aflatoxins, OTA, and ZEA for rye and rice were between 86 and 93% when a 0.5 g sample matter per immunoaffinity column was used.     

Determination of chlorobenzenes in water by drop-based liquid-phase microextraction and gas chromatography-electron capture detection

A drop-based liquid phase microextraction and gas chromatographic-electron capture detection (GC-ECD) method was described for the determination of chlorobenzenes including chlorobenzene, 1,2-dichlorobenzene, 1,3-dichlorobenzene, 1,4-dichlorobenzene and 1,2,3-trichlorobenzene in 5 ml of water. The method used 2 microl of n-hexane as extraction solvent, 5 min extraction time, a stirring rate of 600 rpm and sample ionic strength of 3 M maintained with sodium chloride at 25 degrees C (ambient temperature). The limits of detection (LODs) ranged from 0.004 microg l(-1) (for 1,3-dichlorobenzene) to 0.008 microg l(-1) (for monochlorobenzene). The dynamic linear range for all investigated chlorobenzenes was 1-50 microg l(-1). Recoveries of chlorobenzenes from fortified distilled water are over 90% for three different fortification levels (5, 15 and 45 microg l(-1)) and relative standard deviations of the recoveries are below 6%. Analysis of fortified (5 microg l(-1)) real water samples revealed that matrices had no adverse effect on extraction efficiency of proposed method. The recovery of fortified real water samples was from 90 to 94% with relative standard deviations below 6%.     

Quantitative analysis of 4-ethylphenol and 4-ethylguaiacol in red wine

2,3,5,6-[2H4]-4-Ethylphenol (d4-4-ethylphenol) was synthesised for use as an internal standard in a new, rapid and accurate analytical method, employing gas chromatography-mass spectrometry to determine the concentration of the important aroma compounds 4-ethylphenol and 4-ethylguaiacol in red wine. The concentrations of both compounds in wine stored in 44 American and 47 French new and used oak barrels from several suppliers were measured. Wine stored in shaved and refired oak barrels contained up to 85% less 4-ethylphenol and 4-ethylguaiacol than wine stored in normal barrels of the same age that were not shaved. The concentration of 4-ethylphenol found in 61 bottled commercial Australian red wines of various ages ranged from 2 microg/l in a Merlot up to 2660 microg/l in a Shiraz, with a mean concentration of 795 microg/l. 4-Ethylguaiacol was also detected in every red wine analysed, ranging in concentration from 1 microg/l (in a Pinot Noir) up to 437 microg/l (in a Merlot) with a mean concentration of 99 microg/l.     

Ochratoxin A survey in Portuguese wine by LC-FD with direct injection

Wine and grape juices were identified as one of the most important sources of ochratoxin A (OTA), a mycotoxin with diverse toxic effects that naturally appears in food and foodstuffs all over the world.The aim of this study was to assess the OTA levels in Portuguese wines through the application of a simple and accurate method based on liquid chromatography (LC) with direct injection, followed by fluorescence detection (FD).Randomly selected wine samples were used to evaluate the performance of direct injection as efficient, fast, inexpensive and safe sample preparation method. The proposed method was successfully validated. The limit of quantification (LOQ) was 1.0 μg/L and OTA recoveries from wine samples, spiked at the three fortification levels, were higher than 85.4%, with RSDs lower than 9.6% for both red and white wines. The presence of OTA was confirmed by methyl ester derivatization followed by LC analysis.Data on OTA levels were obtained for 60 Portuguese red and white wine samples. OTA was found in 12 samples, nine (26%) red wine samples and three (12%) white wine samples. Only one red wine sample and one white wine sample presented a contamination level above the LOQ, with 1.23 and 2.4 μg/L, respectively. It should be pointed out that this white wine sample exceeded the EC maximum permitted level of 2.0 μg/L. The safe dose established as 120 ng/kg body weight/week was not exceeded by the weekly intake estimated for the samples contaminated above the LOQ.     

Fluorescence polarization immunoassay for rapid screening of ochratoxin A in red wine

A fluorescence polarization (FP) immunoassay, based on a monoclonal antibody and an ochratoxin A (OTA)-fluorescein tracer, has been developed for rapid screening of OTA in red wine. Wine samples were diluted with methanol and passed through aminopropyl solid-phase extraction columns prior to the FP assay. Average recoveries from samples spiked with OTA at levels of 2.0 and 5.0 ng/mL were 79% with RDS of 11% (n = 6). The limit of detection of the FP immunoassay was 0.7 ng/mL OTA, and the whole analysis was performed in less than 10 min. The assay was tested on 154 red wine samples (naturally contaminated or spiked at level ranging from 0.1 to 5.0 ng/mL) and compared with an high-performance liquid chromatography/immunoaffinity column clean-up method, showing a good correlation (r = 0.9222). Their compliance with the European regulation (2.0 ng/mL OTA maximum permitted level) was correctly assessed for 70% of the analyzed samples of red wine, whereas confirmatory analyses were required for the remaining ones with OTA levels close to the regulatory limit. No false-negative or positive results were observed using the FP immunoassay. The proposed FP assay is a useful screening method for OTA in red wines, when high throughput is required, that could also be used for white and rosé wines, which are known to contain less interfering compounds such as polyphenols.     

Coupling solid-phase microextraction and high-performance liquid chromatography for direct and sensitive determination of halogenated fungicides in wine

A solid-phase microextraction (SPME) method coupled to high-performance liquid chromatography with diode array detection (HPLC-DAD) for the analysis of six organochlorine fungicides (nuarimol, triadimenol, triadimefon, folpet, vinclozolin and penconazole) in wine was developed. For this purpose, polydimethylsiloxane-divinylbenzene-coated fibers were utilized and all factors affecting throughput, precision, and accuracy of the SPME method were investigated and optimized. These factors include: matrix influence, extraction and desorption time, percentage of ethanol, pH, salt effect and desorption mode. The performed analytical procedure showed detectability ranging from 4 to 27 microg l(-1) and precision from 2.4 to 14.2% (as intra-day relative standard deviation, RSD) and 4.7-25.7% (as inter-day RSD) depending on the fungicide. The results demonstrate the suitability of the SPME-HPLC-DAD method to analyze these organochlorine fungicides in red wine.     

Non-instrumental immunochemical tests for rapid ochratoxin A detection in red wine

Gel-based and membrane-based flow-through immunoassay formats were investigated for rapid ochratoxin A (OTA) detection in red wine. The flow-through set-up consisted of an antibody containing gel or membrane placed at the bottom of a standard solid-phase extraction column (i.e. the flow-through column), combined with a clean-up column. Different clean-up methods were studied for red wine clarification and purification. The optimal method consisted of passing wine, diluted with an aqueous solution containing 1% polyethylene glycol (PEG 6000) and 5% sodium hydrogencarbonate, through strong anion exchange (SAX) silica. An immunoassay for OTA detection in red wine was optimized and a cut-off level at 2 μg L⁻¹ according to EU legislation was achieved with both formats. A more significant colour difference between blank and spiked samples was observed for the gel-based assay making this superior to the membrane-based assay. The proposed rapid gel-based test was compared with a standard immunoaffinity column - high-performance liquid chromatography - fluorescent detection (IAC-HPLC-FLD) method and a good correlation of the results was obtained for naturally contaminated wine samples.     

A study of Nafion-coated bismuth-film electrodes for the determination of trace metals by anodic stripping voltammetry

This work reports on the fabrication, characterization and applications of Nafion-coated bismuth-film electrodes (NCBFE's) for the determination of trace metals by anodic stripping voltammetry (ASV). A NCBFE was typically prepared by first applying a 5 microl drop of a 1% Nafion solution onto the surface of a glassy-carbon rotating-disk electrode. After evaporation of the solvent, the Bi film was plated on the electrode in situ(i.e. by spiking the sample with 1000 microg l(-1) of Bi(iii) and simultaneous electrolytic deposition of the metal ions and bismuth film on the electrode surface at -1.4 V) or ex-situ(i.e. by electrolytic deposition of the bismuth film in a separate solution containing 1000 microg l(-1) of Bi(iii), followed by the ASV measurement step in the sample solution). Various fabrication and operational parameters were thoroughly investigated and discussed in terms of their effect on the ASV signals. It was found that this voltammetric sensor was suitable for the determination of metals at trace levels by square-wave ASV (SWASV) due to its multi-element detection potential, improved analytical sensitivity, high resistance to surfactants, low cost, ease of fabrication, robustness, speed of analysis and low toxicity (as compared to traditional mercury electrodes). In the presence of 4 mg l(-1) of Triton X-100, the NCBFE afforded a 10-fold peak height enhancement for the Pb peak and a 14-fold enhancement for the Cd peak over a bare BFE while the determination of Zn was feasible only on the NCBFE. The limits of detection (at a signal-to-noise ratio of 3) were 0.1 microg l(-1) for Cd and Pb and 0.4 microg l(-1) for Zn for a deposition time of 10 min. Finally, the electrode was applied to different real samples (tap-water, urine and wine) for the analysis of trace metals with satisfactory results.     

Validation of a liquid chromatography method for the simultaneous quantification of ochratoxin A and its analogues in red wines

A validated high-performance liquid chromatography (HPLC) method with fluorescence detection for the simultaneous quantification of ochratoxin A (OTA) and its analogues (ochratoxin B (OTB), ochratoxin C (OTC) and methyl ochratoxin A (MeOTA)) in red wine at trace levels is described. Before their analysis by HPLC-FLD, ochratoxins were extracted and purified with immunoaffinity columns from 50 mL of red wine at pH 7.2. Validation of the analytical method was based on the following parameters: selectivity, linearity, robustness, limits of detection and quantification, precision (within-day and between-day variability), recovery and stability. The limits of detection (LOD) in red wine were established at 0.16, 0.32, 0.27 and 0.17 ng L(-1) for OTA, OTB, MeOTA and OTC, respectively. The limit of quantification (LOQ) was established as 0.50 ng L(-1) for all of the ochratoxins. The LOD and LOQ obtained are the lowest found for OTA in the reference literature up to now. Recovery values were 93.5, 81.7, 76.0 and 73.4% for OTA, OTB, MeOTA and OTC, respectively. For the first time, this validated method permits the investigation of the co-occurrence of ochratoxins A, B, C and methyl ochratoxin A in 20 red wine samples from Spain.     

Restricted access supramolecular solvents for sample treatment in enzyme-linked immuno-sorbent assay of mycotoxins in food

A restricted access supramolecular solvent (SUPRAS-RAM) made up of tetradecanoic acid reverse micelles is proposed as a wide-scope and low-cost strategy for the treatment of agrifood samples prior to enzyme-linked immunosorbent assays (ELISA). The approach was assessed for the determination of ochratoxin A (OTA) in wines and spices and aflatoxin B1 (AFB1) in cereals, two ubiquitous mycotoxins that were selected as representative contaminants for this study. The samples were selected to cover a variety of matrices in terms diverse composition and high complexity. Macromolecules such as proteins and carbohydrates were not-co-extracted due to the restricted access properties of the SUPRAS that are provided by chemical and physical mechanisms. In this sense, analyte extraction and clean-up were carried out in a single step. Parameters determining the extraction efficiency were studied and optimized. Certified reference materials were used for method validation. Recoveries of OTA ranged between 83% and 96% in wines (with relative standard deviation, RSD, of about 10%) and between 81% and 93% in spices (RSD 7%). Recoveries for AFB1 in wheat ranged from 75% to 85% (RSD 8%). The detection limits were all below the maximum levels established for OTA and for AFB1 by EU directives. This method offers a green and low-cost alternative to the organic solvent-based extraction and/or immunoaffinity columns-based cleanup of complex samples prior to ELISA.     

Determination of Ochratoxin A in wine at sub ng/mL levels by solid-phase microextraction coupled to liquid chromatography with fluorescence detection

Solid-phase microextraction (SPME), using a polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber, interfaced with liquid chromatography-fluorescence detection (LC-FD) has been applied to the determination of Ochratoxin A (OTA) in wine samples. Compared to the most widely adopted extraction/clean-up procedure based on immunoaffinity columns (IAC), the solventless extraction is simpler and cost-effective, requiring the simple immersion of the fiber in diluted wine samples. Furthermore, a fast LC separation is achieved under isocratic conditions. The linear range investigated in wine was 0.25-8 ng/mL; at fortification levels of 0.5 and 2 ng/mL, within-day intra-laboratory precision (repeatability) values, expressed as RSD%, were 5.9 and 5.1, respectively, whereas between days (n = 4) precision was 8.5 and 7.1%, respectively. The limit of detection (LOD) at a signal-to-noise (S/N) ratio of 3 was 0.07 ng/mL; the limit of quantification (LOQ) calculated at S/N = 10 was 0.22 ng/mL, well below the European regulatory level of 2 ng/mL. The potential of the method has been demonstrated by the analysis of a number of different wine samples.