Studies on transport phenomena in electrothermal vaporization sample introduction applied to inductively coupled plasma for optical emission and mass spectrometry

In the present work electrothermal vaporization (ETV) was used in both inductively coupled plasma mass spectrometry (ICP-MS) and optical emission spectrometry (OES) for sample introduction of solution samples. The effect of (Pd + Mg)-nitrate modifier and CaCl₂ matrix/modifier of variable amounts were studied on ETV-ICP-MS signals of Cr, Cu, Fe, Mn and Pb and on ETV-ICP-OES signals of Ag, Cd, Co, Cu, Fe, Ga, Mn and Zn. With the use of matrix-free standard solutions the analytical curves were bent to the signal axes (as expected from earlier studies), which was observed in the 20–800 pg mass range by ICP-MS and in the 1–50 ng mass range by ICP-OES detection. The degree of curvature was, however, different with the use of single element and multi-element standards. When applying the noted chemical modifiers (aerosol carriers) in microgram amounts, linear analytical curves were found in the nearly two orders of magnitude mass ranges. Changes of the CaCl₂ matrix concentration (loaded amount of 2–10 μg Ca) resulted in less than 5% changes in MS signals of 5 elements (each below 1 ng) and OES signals of 22 analytes (each below 15 ng). Exceptions were Pb (ICP-MS) and Cd (ICP-OES), where the sensitivity increase by Pd + Mg modifier was much larger compared to other elements studied. The general conclusions suggest that quantitative analysis with the use of ETV sample introduction requires matrix matching or matrix replacement by appropriate chemical modifier to the specific concentration ranges of analytes. This is a similar requirement to that claimed also by the most commonly used pneumatic nebulization of solutions, if samples with high matrix concentration are concerned.     

The development of a method for the determination of trace elements in fuel alcohol by electrothermal vaporization–inductively coupled plasma mass spectrometry using external calibration

A method for the determination of Ag, As, Cd, Cu, Co, Fe, Mn, Ni, Pb, Sn and Tl in fuel alcohol by electrothermal vaporization inductively coupled plasma mass spectrometry is proposed. The determinations were carried out by external calibration against ethanolic solutions, without a chemical modifier, employing the following pyrolysis and vaporization temperatures: 400 °C and 2300 °C for the more volatile analytes and 1000 °C and 2500 °C for the less volatile analytes. The determination of As, Cd, Pb, Sn and Tl was additionally carried out using Pd as modifier at 800 °C pyrolysis and 2400 °C vaporization temperatures. The temperatures were optimized through pyrolysis and vaporization curves. Seven common fuel ethanol, one fuel ethanol with additive and one anhydrous fuel ethanol sample have been analyzed. The measured concentrations were at the μg L⁻¹ level or lower. Since there is no certified reference material for fuel ethanol, the accuracy of the method was checked by the recovery test, with recoveries from 75% to 124%. The limits of detection (LODs), in μg L⁻¹, and the relative standard deviations for 5 replicates were, for the elements in the conditions without modifier: Ag: 0.015 and 9.1%, Co: 0.002 and 10%, Cu: 0.22 and 6.6%, Fe: 0.72 and 4.3%, Mn: 0.025 and 12%, Ni: 0.026 and 9.3%, and for the elements with Pd: As: 0.02 and 2.9%, Cd: 0.07 and 25%, Pb: 0.02 and 3.1%, Sn: 0.010 and 6.0%, Tl: 0.0008 and 2.5%. Electrothermal vaporization avoids the loading of the plasma with organics, allowing the analysis of fuel ethanol by ICP-MS with good accuracy and reasonable precision.     

Inductively coupled plasma mass spectrometry for the sequential determination of trace metals in sea water after electrothermal vaporization of their dithiocarbamate complexes in methyl isobutyl ketone

 A sensitive method has been developed for the sequential determination of V, Mn, Fe, Co, Ni, Cu, Zn, Mo and Sb in sea water using inductively coupled plasma mass spectrometry (ICP-MS) after electrothermal vaporization of their dithiocarbamate complexes in methyl isobutyl ketone (MIBK). After complexion with sodium diethyldithiocarbamate (NaDDTC), all trace analyte elements were simultaneously separated from sea water matrix and concentrated 20 fold in a single extract of MIBK, followed by introduction of 10 μL of the extract into argon plasma using a pyrolytic graphite rod electrothermal vaporizer (ETV). Sensitivity enhancement due to chemical modification using a mixed modifier of Pd(NO₃)₂-Mg(NO₃)₂ was observed for all the elements. The limits of detection ranged from 2 ng/L for Co to 329 ng/L for V. For replicate determinations of the elements in sea water, the repeatability was within 10% (as a coefficient variation), except for V (12.8%). The recovery test performed on a sea water sample resulted in a range value from 87% for Sb to 119% for V. The method has been successfully applied to sea water samples collected from the surface to the depth of 5000 m at a sampling station in the northwest Pacific Ocean. Received: 1 July 1996/Revised: 24 September 1996/Accepted: 25 September 1996     

Inductively coupled plasma mass spectrometry for the sequential determination of trace metals in sea water after electrothermal vaporization of their dithiocarbamate complexes in methyl isobutyl ketone

 A sensitive method has been developed for the sequential determination of V, Mn, Fe, Co, Ni, Cu, Zn, Mo and Sb in sea water using inductively coupled plasma mass spectrometry (ICP-MS) after electrothermal vaporization of their dithiocarbamate complexes in methyl isobutyl ketone (MIBK). After complexion with sodium diethyldithiocarbamate (NaDDTC), all trace analyte elements were simultaneously separated from sea water matrix and concentrated 20 fold in a single extract of MIBK, followed by introduction of 10 μL of the extract into argon plasma using a pyrolytic graphite rod electrothermal vaporizer (ETV). Sensitivity enhancement due to chemical modification using a mixed modifier of Pd(NO₃)₂-Mg(NO₃)₂ was observed for all the elements. The limits of detection ranged from 2 ng/L for Co to 329 ng/L for V. For replicate determinations of the elements in sea water, the repeatability was within 10% (as a coefficient variation), except for V (12.8%). The recovery test performed on a sea water sample resulted in a range value from 87% for Sb to 119% for V. The method has been successfully applied to sea water samples collected from the surface to the depth of 5000 m at a sampling station in the northwest Pacific Ocean. Received: 1 July 1996/Revised: 24 September 1996/Accepted: 25 September 1996     

The use of electrothermal vaporization ICP-OES for the determination of trace elements in human hair using slurry sampling and PTFE as modifier

A procedure for the determination of trace elements in human hair has been proposed by electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP-OES) with slurry sampling. Slurry was prepared by immersing human hair with conc. HNO₃ and then adding a polytetrafluoroethylene (PTFE) slurry, which was used as a chemical modifier for the improvement of vaporization characteristic of analyte. The slurry was homogenized with an ultrasonic vibrator before the measurement. The vaporization behaviour of the analytes in slurry and solution and the main influence factors for the determination were studied with the addition of PTFE systematically. Detection limits for this method varied from 0.033?µg?g^?1 (Cu) to 3.21?µg?g^?1 (Zn) with the relative standard deviations (RSDs) of 2.8–7.1%. The proposed method was successfully applied for the determination of trace elements (Cu, Mn, Cr, Fe, Zn, Cd and Pb) in human hair with minimum chemical pretreatment and aqueous calibration. The accuracy was checked by comparing the results of this method with those using pneumatic nebulization (PN) ICP-OES after a conventional acid decomposition of the same sample. In addition, the standard reference material of human hair (GBW 07601) was analysed with good agreement between the results from the proposed method and the certified values.     

Vaporization and atomization of the platinum group elements in the graphite furnace investigated by electrothermal vaporization-inductively coupled plasma-mass spectrometry

The mechanisms by which the platinum group elements (PGEs) are vaporized in the graphite furnace have been investigated using electrothermal vaporization-inductively coupled plasma-mass spectrometry (ETV-ICP-MS). The results suggest that live of these elements (Ru, Rh, Pd, Ir and Pt) are reduced to their metallic state in the graphite furnace and then vaporized by direct sublimation of the metal. For Os, the vaporization mechanism is different. In the presence of HNO₃, two distinct vaporization processes are observed. Volatile oxides of Os are released at low temperatures, but some of this oxide is reduced to relatively involatile Os metal which is then vaporized when the temperature is increased above 2000°C. The addition of TeCl₂ chemical modifier was found to have minimal effect on the vaporization mechanism and sensitivity for determination for five of the PGEs. For Os, however, the analytical sensitivity and limit of detection was improved when Te modifier was used in conjunction with a lower vaporization temperature of 1400°C. Optimum conditions for the determination of the PGEs by ETV-ICP-MS are reported, along with their absolute limits of detection; these range from 0.015 pg for Ir to 0.25 pg for Os.     

Hollow-fiber liquid-phase microextraction prior to low-temperature electrothermal vaporization ICP-MS for trace element analysis in environmental and biological samples

A new method of hollow-fiber liquid-phase microextraction (HF-LPME) prior to electrothermal vaporization (ETV) inductively coupled plasma mass spectrometry (ICP-MS) determination of trace Cu, Zn, Pd, Cd, Hg, Pb and Bi, based on gaseous compounds introduction into the plasma as their diethyldithiocarbmate (DDTC) chelates, was developed. The use of the reagent DDTC as chemical modifier could not only enhance the analytical signals, but also decrease the vaporization temperature. At a temperature of 1300 degrees C, trace Cu, Zn, Pd, Cd, Hg, Pb and Bi can be vaporized completely into the ICP. The factors affecting the formation of the chelates and their vaporization behaviors were investigated in detail, and the microextraction conditions were optimized. Under the optimized conditions, the detection limits of the proposed method were 12.4, 28.7, 7.9, 4.5, 3.3, 4.8 and 1.6 pg ml(-1) for Cu, Zn, Pd, Cd, Hg, Pb and Bi, respectively. Enrichment factors of 305, 284, 24, 29, 20, 73 and 43 could be achieved within 15 min of extraction time, and the relative standard deviations (RSDs) for the seven determinations of 0.5 ng ml(-1) of target analytes were 8.8, 6.9, 7.1, 9.4, 10.2, 6.1 and 10.8%, respectively. The newly developed method has been applied to the determination of trace Cu, Zn, Pd, Cd, Hg, Pb and Bi in environmental water and human serum samples, and the recoveries for the spiked samples were in the range of 88-116%. In order to validate this method, two certified reference materials, GBW08501 peach leaves and GBW(E)080040 seawater, were analyzed, and the determined values were in good agreement with the certified values.     

Analysis of fish otoliths by electrothermal vaporization inductively coupled plasma mass spectrometry: aspects of precipitating otolith calcium with hydrofluoric acid for trace element determination

A method is developed for determination of trace elements, including Ag, As, Cd, Co, Cr, Cu, Mn, Ni, Se, Tl and Zn, in fish otoliths by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS). Hydrofluoric acid was used to precipitate calcium resulting from acid dissolution of otolith calcium carbonate. Initial acidity of the sample solution influenced the precipitation efficiency of calcium fluoride. Up to 99.5% of Ca was precipitated in solutions that contained less than 2% (v/v) HNO₃. Recoveries of the elements obtained from spiked artificial otolith solutions were between 90 and 103%. Stabilization of the elements within the ETV cell was achieved with 0.3 μg Pd/0.2 μg Rh chemical modifier that also afforded optimum sensitivity for multielement determination. The method was validated by the analysis of a fish otolith reference material (CRM) of emperor snapper, and then applied to the determination of the trace elements in otoliths of several fish species captured in Raritan Bay, New Jersey. Results indicated that fish physiology and biological processes could influence the levels of Cu, Mn, Se and Zn in the otoliths of fish inhabiting a similar aqueous environment. Otolith concentrations of Cr and Ni did not show any significant differences among different species. Concentrations for Ag, As, Cd, Co and Tl were also not significantly different, but were very low indicating low affinity of otolith calcium carbonate to these elements.     

Direct inductively coupled plasma-atomic emission spectrometry analysis of trace elements in muscle tissues of hairtail using electrothermal vaporization with slurry sampling

A procedure for direct determination of trace elements in muscle tissue of hairtail was developed using inductively coupled plasma-atomic emission spectrometry and electrothermal vaporization with slurry sampling. Due to use of polytetrafluoroethylene as the chemical modifier, the vaporization behaviors of analytes from the slurry and the aqueous standard solutions were very similar. In this case, the aqueous standards could be used for the calibration of slurry samples. The main factors influencing this method were studied systematically. The detection limits for Cr, Ni, Zn, Cd, and Pb were 3.1, 10.5, 176, 6.9, and 83 ng/mL, respectively, and the relative standard deviations were less than 10%. The proposed method was applied to the determination of trace Cr, Ni, Zn, Cd, and Pb in hairtail samples with satisfactory accuracy and precision. A certified reference material of mussel (GBW 08571) was analyzed, and good agreement was obtained between the results from the proposed method and certificate values.     

A Sequential Extraction Method Measures the Toxic Metal Content in Fly Ash from a Municipal Solid Waste Incinerator

The purpose of this research was to develop an optimized pretreatment procedure for toxic metals (Pb, Cd, Zn and Cu) content in fly ash from a municipal waste incinerator. In addition, modified sequential extraction procedures were used to characterize the chemical composition of the fly ash samples. The sequential extraction resolved the fly ash elements into the following chemical forms: soluble, exchangeable, carbonate, oxide, organic, and silicate compounds. Certified reference city waste incineration ash (BCR.176) was used as target ash samples. A H₂O₂+HNO₃+HF mixed acid digestion solution with a low temperature evaporation procedure was selected as optimal for the fly ash digestion. The digested solution was analyzed by inductively coupled plasma mass spectrometry (ICP‐MS), which effectively determined the concentrations of the toxic metal elements in BCR.176. Except for Cd, the recovery of Pb, Zn, and Cu under H₂O₂+HNO₃+HF digestion and their sequential extraction procedures were higher than 95%. The relative standard deviations (RSD) for recoveries of the four elements were within 10%. Furthermore, the sequential extraction procedure's results provided information on the potential mobility of the studied elements. Most of the Cd was bound to water‐soluble and carbonate material in the fly ash samples. Most of the Pb, Zn, and Cu was released to carbonates and bound to organic matter in the fly ash samples.     

A systematic study on the influence of carbon on the behavior of hard-to-ionize elements in inductively coupled plasma–mass spectrometry

A systematic study on the influence of carbon on the signal of a large number of hard-to-ionize elements (i.e. B, Be, P, S, Zn, As, Se, Pd, Cd, Sb, I, Te, Os, Ir, Pt, Au, and Hg) in inductively coupled plasma–mass spectrometry has been carried out. To this end, carbon matrix effects have been evaluated considering different plasma parameters (i.e. nebulizer gas flow rate, r.f. power and sample uptake rate), sample introduction systems, concentration and type of carbon matrix (i.e. glycerol, citric acid, potassium citrate and ammonium carbonate) and type of mass spectrometer (i.e. quadrupole filter vs. double-focusing sector field mass spectrometer). Experimental results show that P, As, Se, Sb, Te, I, Au and Hg sensitivities are always higher for carbon-containing solutions than those obtained without carbon. The other hard-to-ionize elements (Be, B, S, Zn, Pd, Cd, Os, Ir and Pt) show no matrix effect, signal enhancement or signal suppression depending on the experimental conditions selected. The matrix effects caused by the presence of carbon are explained by changes in the plasma characteristics and the corresponding changes in ion distribution in the plasma (as reflected in the signal behavior plot, i.e. the signal intensity as a function of the nebulizer gas flow rate). However, the matrix effects for P, As, Se, Sb, Te, I, Au and Hg are also related to an increase in analyte ion population caused as a result of charge transfer reactions involving carbon-containing charged species in the plasma. The predominant specie is C⁺, but other species such as CO⁺, CO₂⁺, C₂⁺ and ArC⁺ could also play a role. Theoretical data suggest that B, Be, S, Pd, Cd, Os, Ir and Pt could also be involved in carbon based charge transfer reactions, but no experimental evidence substantiating this view has been found.     

Investigations on the use of chemical modifiers for the direct determination of trace impurities in Al2O3 ceramic powders by slurry electrothermal evaporation coupled with inductively-coupled plasma mass spectrometry (ETV–ICP–MS)

The direct determination of trace impurities in Al₂O₃ ceramic basic powders by ICP–MS using electrothermal evaporation (ETV) with slurry sampling has been investigated. To increase interference-free analyte volatilization, the use of the palladium-group modifiers (PGM) IrCl₃, Pd(NO₃)₂, and PdCl₂ for the determination of Ca, Fe, Ga, Mg, Mn, Na, Ni, and V in Al₂O₃ powders was studied. Their role, which in ETV–ICP–MS and ETV– ICP–OES is to stabilize the investigated analyte during the ashing phase, to increase vaporization of the matrix, and to reduce transport losses was investigated. Optimum analysis results were obtained with PdCl₂ modifier when 500 ng Pd was used for a sample weight of 100 μg Al₂O₃ injected into the ETV. Calibration was performed by standard addition with aqueous solutions of the analytes. The RSDs calculated from triplicate analysis ranged form 5 to 10%. Detection limits between 0.07 μg g^–1 (Ga) and 1.1 μg g^–1 (Na) were achieved. The accuracy was proven for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V by analyzing an NIST standard reference Al₂O₃ material (SRM 699) with a middle grain size of 16.4 μm. The analytical method was used for the analysis of Al₂O₃ powder (AKP 30, Sumitomo, Japan) with impurities in the low μg g^–1 range and a middle grain size of 1.1 μm. The results obtained for the elements Ca, Fe, Ga, Mg, Mn, Na, Ni, and V were comparable with those obtained by ICP–MS subsequent to conventional decomposition with hydrochloric acid at high pressure.     

Slurry Sampling Electrothermal Vaporization Combined with ICP-AES for Direct Analysis of Environmental Samples

In this article, a polytetrafluoroethylene (PTFE) slurry was used as a chemical modifier for direct determination of trace elements in environmental samples by electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) with slurry sampling. The vaporization behaviors of the analytes in slurry and solution were comparatively studied in the presence of PTFE. The main influence factors for this method were examined. Under the optimum operating conditions, the precision of this method was better than 7% with the detection limits varying from 1.7 ng mL^?1 (Cu) to 203 ng mL^?1 (Zn). The proposed method has been applied to the direct determination of the trace elements in camphor tree leaves and standard reference material (the combined sample of branch and leaf of shrub, GBW 07603) with satisfactory results.     

Electrothermal vaporization inductively coupled plasma atomic emission spectrometry determination of gold, palladium, and platinum using chelating resin YPA(4) as both extractant and chemical modifier

A new method for determination of trace gold (Au), palladium (Pd), and platinum (Pt) in environmental and geological samples by electrothermal vaporization (ETV)-inductively coupled plasma atomic emission spectrometry (ICP-AES) with the use of chelating resin YPA₄ as both solid phase extractant and chemical modifier has been developed. The resin loaded with analytes was prepared to slurry and directly introduced into the graphite furnace without any pretreatment. The factors affecting the vaporization behaviors of Au, Pd, and Pt were investigated in detail. It was found that, in the presence of YPA₄, Au and Pd could be quantitatively vaporized at lower vaporization temperature of 1900 °C. Compared with the conventional electrothermal vaporization, the vaporization temperature was decreased by 700 °C, and the detection limits for Au and Pd was decreased by a three-fold. However, a little effect of YPA₄ on the ETV-ICP-AES determination of Pt was found. Under the optimized conditions, the detection limits (3σ) of Au, Pd, and Pt for this method are 75, 60, and 217 pg, respectively; and their relative standard deviations (R.S.D.) are 4.4, 5.6, and 3.7%, respectively (n=9, C=0.2 μg ml⁻¹). The proposed method has been applied to the determination of trace Pd and Pt in sewage sludge, and the results well agreed with the recommended values. In order to further verify the accuracy of the developed method, a GBW07293 certified geological reference material and an auto catalyst NIST SRM 2557 reference material were analyzed, and the determined values coincided with the certified values very well.     

Optimization of the electrothermal vaporization conditions for inductively coupled plasma excitation spectrometry: Selective volatilization versus covolatilization approaches

A new version of the outlet port of a graphite furnace electrothermal vaporizer (upward streaming system) is described, in which the hot sample vapour is mixed with an auxiliary carrier argon stream of ambient temperature. The operation procedures using carrier volatilization of organic liquids as gas phase additives are also outlined. The selective volatilization and transport efficiency for As, Cd, Hg, Pb, Sb, Se and Zn could be increased by applying sodium thiosulfate as chemical modifier to solution samples with controlled nitric acid content. On the other hand, a near simultaneous vaporization of 16 elements using chlorination with CCl₄ vapour at 2100° C could be performed for a multielement analysis. By wetting the auxiliary carrier argon stream, the linearity of the analytical curves was improved (except for chromium), when applying multielement standards. Linear analytical curves could also be obtained in the presence of alkali and alkaline earth metal matrices in multielement standards using halocarbon assisted electrothermal vaporization sample introduction.     

The use of chemical modifiers in the determination of cadmium in sewage sludge and tin in PVC by solid sampling-graphite furnace atomic absorption spectrometry

The effects of NH₄H₂PO₄ and Pd as chemical modifiers in SS-GFAAS are studied in the determination of Cd in sewage sludge and of Sn in PVC samples. Whereas for Cd both modifiers act equally well whether Cd is in solution or in the solid sample, the effect of Pd on tin is different. To make the Pd modifier as effective on Sn in PVC as on Sn in solution a two-step pyrolysis must be introduced into the temperature programme. It is also shown that the contribution of the application of chemical modifiers to the final imprecision of the determination is negligible compared to that introduced by the sample inhomogeneity.     

Direct determination of cadmium in urine by tungsten-coil inductively coupled plasma atomic emission spectrometry using palladium as a permanent modifier

Cadmium is determined in urine samples collected from patients with age-related diseases. The urine is simply diluted 1:1 with water and placed on a tungsten coil electrothermal vaporizer treated with 200 μg of a permanent Pd modifier. A straightforward vaporization program is used to deliver the Cd vapor to an inductively coupled plasma atomic emission spectrometer. A high resolution spectrometer and a charge coupled device detector provide spectra across a 4.8 nm window encompassing two separate Cd emission lines: 226.5 and 228.8 nm. The limit of detection is 0.2 μg/L at each wavelength, and the linear dynamic range spans three orders of magnitude. The accuracy as measured with a urine standard reference material is 94%. The Pd modifier continues to be effective even after 150 vaporization cycles. Direct analysis of urine with the Pd modifier using simple aqueous calibration solutions provides results that are comparable to those observed after a much more complex method: chelation, extraction, and internal standardization without the modifier. The mean concentrations found by the two techniques differ by only 9%. The permanent Pd modifier allows direct analysis of limited sample volumes with decreased risks of contamination.     

Graphite furnace analysis—getting easier and achieving more?

The impact of microwave digestion, hot injection of solutions and chemical modification on the analysis of biological samples by electrothermal atomic absorption spectrometry (AAS) has been assessed. The stabilizing effects of palladium and ruthenium modifiers were compared. Although ruthenium has a higher atom appearance temperature, palladium was the more useful modifier when samples other than water were analysed. When 2 μg of palladium (as PdCl₂) was preconditioned in hydrogen at 500°C, volatile elements were retained at char temperatures up to 1000–1100°C. This allowed similar atomizer programmes to be used for Cd, Cu, Fe, Mn and Pb and accurate determination of these analytes in solutions of reference materials was achieved aqueous standards. Rapid drying of the solutions by hot injection at 120°C reduced the programme time to just over 1 min. A combination of microwave digestion, hot injection of 40% (w/v) HNO₃ solutions and Pd modification produced a rapid and sensitive method for determination of Cd and Pb at sub-μg g^?1 levels in vegetable and protein foodstuffs. Palladium modification also proved useful in simultaneous multi-element determination by continuum source AAS. The picogram detection limits obtained for Cr, Mn and Pb were similar to line source AAS values recorded with the same compromise programme. Accurate determination of Cd, Cr, Cu, Mn, Mo and Pb in NIST SRM 1566 Oyster Tissue indicated the potential of continuum source AAS for multi-element determinations. The advantages of palladium modifications were also illustrated for furnace atomic non-thermal excitation spectrometry (FANES) with a hollow-cathode discharge. The maximum char temperatures of Ag, Ga, Hg, Pb, Sb and Se were increased by 300–600°C in the presence of 1 μg of Pd, although the detection limits were a factor of two poorer.     

The role of modifiers in electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) for the determination of B,La and U

The role of modifiers in electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) for the determination of refractory elements such as La or U and carbide forming elements such as B has been studied. Solutions of NH₄F, NH₄Cl, NH₄Br, NaCl, NaF, NH₄HSO₄, (NH₄)₂HPO₄, the gaseous halogenated hydrocarbons CHF₃ and CCl₂F₂ and HCl have been used as modifiers.The mechanism of the modifier effect and the influence of modifiers on sensitivity enhancement have been investigated. The sensitivity enhancements are great enough to achieve absolute detection limits of 2–6 pg for boron and 10 fg for La and U. The signal reproducibility is 0.5–3.0% for a concentration of 1 μg 1⁻¹ La and U, and 20 μg 1⁻¹ boron. Therefore, by adding modifiers, the use of ETV-ICP-MS can be extended to trace element determination of refractory and carbide forming elements in μl amounts of sample.     

Solid phase extraction for analysis of biogenic carbonates by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS): an investigation of rare earth element signatures in otolith microchemistry

Uptake of trace elements into fish otoliths is governed by several factors such as life histories and environment in addition to stock and species differences. In an attempt to elucidate the elemental signatures of rare earth elements (REEs) in otoliths, a solid phase extraction (SPE) protocol was used in combination with electrothermal vaporization (ETV) as a sample introduction procedure for the determinations by inductively coupled plasma quadrupole mass spectrometry (ICP-MS). Effects of various parameters, such as carrier gas flow rate, atomization temperature and chemical modification, were examined for optimization of the conditions by ETV-ICP-MS. Atomization was achieved at 2800 °C. Lower temperatures (i.e. 2600 °C) resulted in severe memory problems due to incomplete atomization. Palladium was used as a chemical modifier. It was found that an increase in Pd concentration up to 0.5 μg in the injection volume (70 μl) led up to four-fold enhancement in the integrated signals. This phenomenon is attributed to the carrier effect of Pd rather than the stabilization since no significant losses were observed for high temperature drying around 700 °C even in the absence of Pd. Preconcentration was performed on-line at pH 5 by using a mini-column of Toyopearl AF-Chelate 650M chelating resin, which also eliminated the calcium matrix of otolith solutions. After preconcentration of 6.4 ml of solution, the concentrate was collected in 0.65 ml of 0.5% (v/v) HNO₃ in autosampler cups, and then analyzed by ETV-ICP-MS. The method was validated with the analysis of a fish otolith certified reference material (CRM) of emperor snapper, and then applied to samples. Results obtained from otoliths of fish captured in the same habitat indicated that otolith rare earth element concentrations are more dependent on environmental conditions of the habitat than on species differences.