Simultaneous determination of arsenic, selenium and antimony species using HPLC/ICP-MS

A new method for the simultaneous separation and determination of four arsenic species [As(III), As(V), monomethylarsonic acid and dimethylarsinic acid], three selenium species [Se(IV), Se(VI) and selenomethionine] as well as Sb(III) and Sb(V) is presented. The speciation was achieved by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Chromatographic parameters such as the composition and pH of the mobile phase were optimised. Limits of detection are below 4.5 μg L^–1 (as element) for Sb(III) and the selenium species and below 0.5 μg L^–1 for the other species. Precisions of retention times were better than 2% RSD and of peak areas better than 8% RSD for all the species investigated.     

Speciation of four selenium compounds using high performance liquid chromatography with on-line detection by inductively coupled plasma mass spectrometry or flame atomic absorption spectrometry

An analytical method for the speciation of selenomethionine, selenocystine, selenite and selenate by high performance liquid chromatography (HPLC) with atomic spectrometric detection is presented. An organic polymeric strong anion exchange column was used as the stationary phase in combination with an aqueous solution of 6 mmol L^–1 of salicylate ion at pH 8.5 as the mobile phase which allowed the isocratic separation of the four selenium analytes within 8 minutes. The separated selenium species were detected on-line by flame atomic absorption spectrometry (FAAS) or inductively coupled plasma mass spectrometry (ICP-MS). The signal-to-noise ratio of the FAAS detector was optimized using a hydrogen-argon entrained-air flame and a slotted-tube atom trap (STAT) in the flame. The limit of detection (3 σ) achieved by the HPLC-FAAS system was 1 mg L^–1 of selenium (100 μL injections) for each of the four selenium species. More powerful selenium detection was achieved using an ELAN 5000 ICP-MS instrument. Selenium was measured at m/z = 82. The ICP-MS signal intensity was enhanced by a factor of 3–4 after addition of 3% methanol to the chromatographic mobile phase and by using an increased plasma power input of 1300 W. The limit of detection achieved under these conditions was 1 μg L^–1 (100 μL injections). The HPLC-ICP-MS system was used for selenium speciation of selenite and selenate in aqueous solutions during a BCR certification exercise and for selenium speciation in the certified reference material, BCR No. 402 White Clover. Extraction experiments revealed that the selenium species in the biological material were extractable only in the presence of water in the extraction medium. The results indicated that selenate and a compound of unknown identity U were present in the plant sample.     

Simultaneous determination of arsenic, selenium and antimony species using HPLC/ICP-MS

A new method for the simultaneous separation and determination of four arsenic species [As(III), As(V), monomethylarsonic acid and dimethylarsinic acid], three selenium species [Se(IV), Se(VI) and selenomethionine] as well as Sb(III) and Sb(V) is presented. The speciation was achieved by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Chromatographic parameters such as the composition and pH of the mobile phase were optimised. Limits of detection are below 4.5 μg L^–1 (as element) for Sb(III) and the selenium species and below 0.5 μg L^–1 for the other species. Precisions of retention times were better than 2% RSD and of peak areas better than 8% RSD for all the species investigated. Received: 13 January 1999 / Accepted: 4 March 1999     

Speciation of four selenium compounds using high performance liquid chromatography with on-line detection by inductively coupled plasma mass spectrometry or flame atomic absorption spectrometry

An analytical method for the speciation of selenomethionine, selenocystine, selenite and selenate by high performance liquid chromatography (HPLC) with atomic spectrometric detection is presented. An organic polymeric strong anion exchange column was used as the stationary phase in combination with an aqueous solution of 6 mmol L^–1 of salicylate ion at pH 8.5 as the mobile phase which allowed the isocratic separation of the four selenium analytes within 8 minutes. The separated selenium species were detected on-line by flame atomic absorption spectrometry (FAAS) or inductively coupled plasma mass spectrometry (ICP-MS). The signal-to-noise ratio of the FAAS detector was optimized using a hydrogen-argon entrained-air flame and a slotted-tube atom trap (STAT) in the flame. The limit of detection (3 σ) achieved by the HPLC-FAAS system was 1 mg L^–1 of selenium (100 μL injections) for each of the four selenium species. More powerful selenium detection was achieved using an ELAN 5000 ICP-MS instrument. Selenium was measured at m/z = 82. The ICP-MS signal intensity was enhanced by a factor of 3–4 after addition of 3% methanol to the chromatographic mobile phase and by using an increased plasma power input of 1300 W. The limit of detection achieved under these conditions was 1 μg L^–1 (100 μL injections). The HPLC-ICP-MS system was used for selenium speciation of selenite and selenate in aqueous solutions during a BCR certification exercise and for selenium speciation in the certified reference material, BCR No. 402 White Clover. Extraction experiments revealed that the selenium species in the biological material were extractable only in the presence of water in the extraction medium. The results indicated that selenate and a compound of unknown identity U were present in the plant sample. Received: 4 September 1996 / Accepted: 12 December 1996     

Speciation analysis of inorganic antimony in soil using HPLC-ID-ICP-MS

Speciation analysis of Sb(III) and Sb(V) in a soil sample was performed through extraction and on-line isotope dilution concentration determination after a chromatographic separation. The total Sb concentration found in a through traffic contaminated soil sample was (4.17 μg g⁻¹, 0.3 μg g⁻¹ SD, n=6). It was determined using ICP-MS after soil digestion using the sodium peroxide sintering method. The optimized extraction procedure for speciation analysis was carried out using 100 mmol L⁻¹ citric acid at pH 2.08 by applying an ultrasonic bath for 45 min at room temperature. The effects of citric acid concentration (0–500 mmol L⁻¹), pH (1–6), and temperature (30–60°C) on inorganic antimony species distribution in the examined sample were studied and optimized. The separation of Sb(III) and Sb(V) was achieved using an anion exchange column (PRP-X100) and 10 mmol L⁻¹ EDTA and 1 mmol L⁻¹ phthalic acid at pH 4.5 as a mobile phase. The eluent from the HPLC was mixed with an enriched (94.2%) ¹²³Sb spike solution that was pumped by a peristaltic pump with a constant flow rate (0.5 mL min⁻¹) in a three-way valve. The blend passed directly to the Conikal nebulizer of the ICP-MS. By using the above extraction procedure and methodology, 43.2% Sb(V) (2.9% RSD, n=3) and 6.0% Sb(III) (1.3% RSD, n=3) of total Sb found in the sample could be detected. The detection limits achieved by the proposed method were 20 ng L⁻¹ and 65 ng L⁻¹ for Sb(V) and Sb(III), respectively. The precision, evaluated by using RSD with 100 ng L⁻¹ calibration solutions, was 2.7% and 3.2% (n=6) for Sb(V) and Sb(III), respectively, in aqueous solutions.     

The analysis of antimony species by using ESI-MS and HPLC-ICP-MS

A new method for the separation of organic antimony as trimethylantimony dichloride (TMSbCl₂) and inorganic Sb(V) and Sb(III) by using anion exchange high-performance liquid chromatography coupled with inductively-coupled plasma mass spectrometry (ICP-MS) is presented. In comparison with previous work the detection limits for both species were significantly decreased, down to 5 ngL^–1, mainly by avoiding any contamination from the chromatographic device. Using an ultrasonic nebulizer (USN) improved the detection limits for inorganic Sb species, but was useless for the HPLC method due to problems in the recovery of the TMSbCl₂. Matrix interferences of the chromatographic determination were studied in detail and the method was applied to environmental samples assumed to contain organic antimony species. Additionally, the molecular structure of the TMSbCl₂ in solution was studied by using electrospray-ionization mass spectrometry (ESI-MS) showing that this species occurs most probably as [TMSbOH]⁺ in aqueous solutions. Received: 22 September 1997 / Revised: 21 November 1997 / Accepted: 27 November 1997     

Sequential determination of Am, Cm, Pu, Np and U by extraction chromatography

Environmental contamination by artificial radionuclides and the evaluation of their sources require precise isotopic analysis and accurate determination of actinide elements above all plutonium and americium. These can be achieved by alpha spectrometry or by inductively coupled plasma mass spectrometry (ICP-MS) after chemical separation. In the present work, a simple, rapid method has been developed for the sequential separation of actinide elements from aqueous solutions and their determination by alpha spectrometry. Extraction chromatography was applied to the separation of ²⁴¹Am, ²⁴⁴Cm, ^{239 + 240,238}Pu, ²³⁷Np and ^238,235,234U using microporous polyethylene supporting tri-n-octylamine as the stationary phase and hydrochloric acid with and without reducing agents as the mobile phase. Actinide in 9 M HCl solution is introduced into the anion exchange column; Pu (IV), Np (IV) and U(VI) are retained on the column while Am (III) and Cm passed through. Pu is eluted first, reductively, after which, Np and then U are eluted. The method can be applied to all aqueous solutions which do not contain strong complexing or precipitation agents for the elements considered.     

Evaluation of Manganese(II) and Manganese(VII) Speciation in Water Samples by Ion Pair High-performance Liquid Chromatography-inductively Coupled Plasma Mass Spectrometry

The speciation of Mn(II) and Mn(VII) is reported by ion pair chromatography. To optimize the separation, sample pH, ion pair reagent, Mn(II) complexing agent, and composition of mobile phase were characterized. The separation of Mn(II) and Mn(VII) was performed using ethylenediamine tetraacetic acid to complex Mn(II), tetrabutylammonium hydroxide as an ion pair reagent, and a C8 column. The separation of the manganese species was demonstrated by high-performance liquid chromatography-inductively coupled plasma mass spectrometry (HPLC ICP-MS). The conversion of Mn(VII) to Mn(II) occurred during the separation and influenced the quantification; hence, the factors affecting this process including the storage time, manganese species ratio, and sample matrix composition were evaluated and suitable calibration was demonstrated. The method was validated by characterization of the selectivity, specificity, linearity, limits of detection and quantification, repeatability, and intermediate precision. The detection limit for Mn(II) was 0.22 µg?L^?1, while for Mn(VII), the value was 1.55 µg?L^?1.     

Mercury determination and speciation analysis in surface waters

A sorbent L-cysteine grafted silica gel has been evaluated for separation and enrichment of dissolved inorganic i-Hg(II) and methylmercury CH₃Hg(I) from surface waters at sub-μg L⁻¹ concentrations. Chemical parameters for mercury species enrichment and separation have been optimized. Analytical schemes for the determination of Hg species, using selective column solid phase extraction (SPE) with continuous flow chemical vapor generation atomic absorption spectrometry (CF-CVG-AAS) or inductively coupled plasma-mass spectrometry (ICP-MS) were developed. Possibilities for on-site SPE enrichment were demonstrated as well. The limits of quantification were 1.5 and 5 ng L⁻¹ for dissolved i-Hg(II) and CH₃Hg(I) by CF-CVG-AAS and 1 and 2.5 ng L⁻¹ by ICP-MS with relative standard deviations between 7–12% and 7–14%, respectively. The chemically modified SPE sorbent has demonstrated high regeneration ability, chemical and mechanical stability, acceptable capacity and good enrichment factors. Results for total dissolved mercury were in reasonable agreement with those from independent analyses by direct ICP-MS determinations for river waters and for estuarine water certified reference material.      

Determination of mercurial species in fish by inductively coupled plasma mass spectrometry with anion exchange chromatographic separation

This work demonstrated the feasibility of mercury speciation analysis by anion exchange chromatographic separation with inductively coupled plasma mass spectrometry detection. For the first time, by complexing with the mobile phase containing 3-mercapto-1-propanesulfonate into negatively charged complexes, fast separation of inorganic mercury (Hg²⁺), monomethylmercury (MeHg), ethylmercury (EtHg) and phenylmercury (PhHg) was achieved within 5 min on a 12.5-mm strong anion exchange column. The detection limits for Hg²⁺, MeHg, EtHg and PhHg were 0.008, 0.024, 0.029 and 0.034 μg L⁻¹, respectively. The relative standard deviations of peak height and peak area (5.0 μg L⁻¹ for each Hg species) were all below 3%. The determined contents of Hg²⁺, MeHg and total Hg in a certified reference material of fish tissue by the proposed method were in good accordance with the certified values with satisfactory recoveries. The relative errors for determining MeHg and total mercury were −2.4% and −1.2%, respectively, with an acceptable range for spike recoveries of 94–101%. Mercury speciation in 11 fish samples were then analyzed after the pretreated procedure. The mercury contents in all fish samples analyzed were found compliant with the criteria of the National Standards of China.     

Optimization of an anion-exchange high performance liquid chromatography-inductively coupled plasma-mass spectrometric method for the speciation analysis of oxyanion-forming metals and metalloids in leachates from cement-based materials

A method was developed for the speciation analysis of the oxyanions of As(III), As(V), Cr(VI), Mo(VI), Sb(III), Sb(V), Se(IV), Se(VI) and V(V) in leachates from cement-based materials, based on anion-exchange HPLC coupled with ICP-MS. The method was optimized in a two-step multivariate approach: the effect of sample pH and mobile phase composition on resolution, peak symmetry and analysis time was studied. Optimum conditions were then identified for the significant experimental factors by studying their interdependence. A mobile phase composition of 20 mM ammonium nitrate, 50 mM ammonium tartrate and pH 9.5 was found to be a compromise optimum for the separation of the target analytes using isocratic elution. The optimum condition provided separation of the analytes in less than 6 min, at a mobile phase flow rate of 1.0 mL/min. The signal intensities of the analytes were improved by adding 1% methanol to the mobile phase. The limit of detection of the method was in the range 0.2–2.2 μg/L for the various species. The effect of sample constituents was studied using spiked concrete leachates. The method was used to determine the target oxyanionic species in leachates generated from a concrete material in the pH range 3.5–12.4; CrO₄²⁻, MoO₄²⁻ and VO₄³⁻ were detected in most of the leachates.     

A high‐performance liquid chromatography assay with a triazole‐bonded column for evaluation of d‐amino acid oxidase activity

Elution profiles of kynurenic acid (KYNA) and 7‐chlorokynurenic acid (Cl‐KYNA) were examined by high‐performance liquid chromatography (HPLC) using a triazole‐bonded stationary phase column (Cosmosil® HILIC) under isocratic elution of a mobile phase consisting of CH₃CN–aqueous 10 mm ammonium formate between pH 3.0 and 6.0. The capacity factors of KYNA and Cl‐KYNA varied with both the CH₃CN content and the pH of the mobile phase. The elution order of KYNA and Cl‐KYNA was reversed between the CH₃CN‐ and H₂O‐rich mobile phases, suggesting that hydrophilic interactions and anion‐exchange interactions caused retention of KYNA and Cl‐KYNA in the CH₃CN‐ and H₂O‐rich mobile phases, respectively. The present HPLC method using a triazole‐bonded column and fluorescence detection (excitation 250 nm, emission 398 nm) was applied to monitor in vitro production of KYNA from d ‐kynurenine (d ‐KYN) by d ‐amino acid oxidase (DAO) using Cl‐KYNA as an internal standard. A single KYNA peak was clearly observed after enzymatic reaction of d ‐KYN with DAO. Production of KYNA from d ‐KYN was suppressed by the addition of commercial DAO inhibitors. The present HPLC method can be used to evaluate DAO activity and DAO inhibitory effects in candidate drugs for the treatment of schizophrenia. Copyright © 2015 John Wiley & Sons, Ltd.     

Anion separations for liquid chromatography using propylpyridinium silica as the stationary phase

This work describes the characterization and potential applications of a silica-based anion-exchange phase prepared by a two-step modification process that incorporates a propylpyridinium group. The effects of pH and eluent concentration on anion separation were examined using 150 mm × 3.9 mm HPLC columns packed with the new phase. The mobile phase pH values ranged from 3.8 to 6.6 using phthalic acid/Tris solutions. The best separation was achieved using 2.5 mmol L⁻¹ phthalate/2.4 mmol L⁻¹ Tris solution at pH 4.2 as mobile phase with non-suppressed conductivity detection. The new stationary phase was used for the separation of some inorganic and organic anions showing good resolution. The stability of the silica-based anion exchange phase was also evaluated.Analytical curves, for concentrations ranging from 0.25 to 10 mg L⁻¹ for the inorganic anions chloride, nitrite, bromide and nitrate, showed good linear correlations (r > 0.998). The method was tested with certified rainwater samples. The measured and certified values were in good agreement, indicating that the new phase holds significant promise for the analysis of these anions in environmental samples.     

Solid-phase extraction (SPE) assays to ascertain the mechanisms of retention of antimony species in several stationary phases

Liquid chromatography is the most suitable technique for antimony speciation in several types of samples. However, efficiency can be poor for some of these peaks, especially Sb(III) and Me₃SbCl₂ (TMSb). Weak and strong anion exchange stationary phases are mainly used for antimony speciation in several chromatographic conditions. The present study examines the possible contribution of the interaction between antimony species (Sb(III), Sb(V) and TMSb) and stationary phase support to the overall retention mechanism in their chromatographic separation. Several SPE cartridges, selected from those mainly used as support in anion exchange columns, were assayed. Sb (V) was quantitatively eluted from the PSDVB (polystyrene divinylbenzene) and SiO₂ phases, showing the absence of interaction. Sb (III) showed some interaction with the PSDVB phase; TMSb showed strong retention with all the cartridges studied and it was only eluted from the PSDVB phase.     

Determination of hexavalent chromium in traditional Chinese medicines by high‐performance liquid chromatography with inductively coupled plasma mass spectrometry

An analytical method that combined high‐performance liquid chromatography with inductively coupled plasma mass spectrometry has been developed for the determination of hexavalent chromium in traditional Chinese medicines. Hexavalent chromium was extracted using the alkaline solution. The parameters such as the concentration of alkaline and the extraction temperature have been optimized to minimize the interconversion between trivalent chromium and hexavalent chromium. The extracted hexavalent chromium was separated on a weak anion exchange column in isocratic mode, followed by inductively coupled plasma mass spectrometry determination. To obtain a better chromatographic resolution and sensitivity, 75 mM NH₄NO₃ at pH 7 was selected as the mobile phase. The linearity of the proposed method was investigated in the range of 0.2–5.0 μg L^?1 (r² = 0.9999) for hexavalent chromium. The limits of detection and quantitation are 0.1 and 0.3 μg L^?1, respectively. The developed method was successfully applied to the determination of hexavalent chromium in Chloriti lapis and Lumbricus with satisfactory recoveries of 95.8–112.8%.     

Confirmation of lead aminocarboxylic complex formation using electrospray ionization mass spectrometry and speciation by anion-exchange chromatography coupled with ICP-MS

Inductively coupled plasma mass spectrometry (ICP-MS) and electrospray ionization mass spectrometry (ESI-MS) were used as complementary techniques to provide element and molecular information for aminocarboxylic lead species including [Pb(NTA)]¹⁻, [Pb(HEDTA)]¹⁻, [Pb(EDTA)]²⁻ and [Pb(DTPA)]³⁻. ESI-MS was used to initially confirm the formation of lead aminocarboxylic complexes in solution and subsequently anion-change chromatography coupled with ICP-MS was used to speciate these complexes using a mobile phase containing 30 mM NH₄H₂PO₄ at pH of 8.0. However, [Pb(NTA)]¹⁻ was not observed during chromatographic separation due to its poor stability. The species [Pb(HEDTA)]¹⁻, [Pb(EDTA)]²⁻ and [Pb(DTPA)]³⁻ were separated within 15 min with reasonable resolution and detection limits ranging from 0.05 to 0.2 μg L⁻¹ with simple direct injection of sample. The proposed method was used to speciate aminocarboxylic lead complexes in soil solution.     

Determination of mercury and methylmercury in seafood by ion chromatography using photo-induced chemical vapor generation atomic fluorescence spectrometric detection

A novel method based on photo-induced chemical vapor generation (CVG) as interface to on-line coupled Hg-cysteine ion chromatograpy (IC) with atomic fluorescence spectrometry (AFS) was developed for rapid determination of methylmercury (MHg) in seafood. Separation of inorganic mercury (Hg²⁺) and methylmercury(CH₃Hg⁺) was accomplished on a Hamilton PRP X-200 polymer-based exchange column with a mobile of 3% acetonitrile, 1% (w/w) L-cysteine and 20 mmol L^{− 1} pyridine and 160 mmol L^{− 1} formic acid, at pH 2.4 within 7 min. Once separated, both species are reduced by formic acid in mobile phase under UV radiation to convert Hg⁰ on-line, which is subsequently swept (by argon carrier gas) into an atomic fluorescence spectrometry (AFS) for measurement. Under the optimized experiment conditions, the detection limits (as Hg), based on three times the standard deviation of a standard solution, were found to be 0.1 ng mL^{− 1} for mercury and 0.08 ng mL^{− 1} for methylmercury, with an injection volume of 100 μL. The developed method was validated by determination of certified reference material DORM-2 and was further applied in determination of seafood samples.     

Hyphenation of reverse-phase HPLC and ICP-MS for metabolite profiling—application to a novel antituberculosis compound as a case study

In this study, a high-performance liquid chromatography (HPLC) inductively coupled plasma (ICP) mass spectrometry (MS) method was developed intended for use in metabolism studies of bromine-containing drugs, administered to test animals (or test persons). As a case study, the method was applied to a new antituberculosis compound, the bromine-containing diarylquinoline R207910. A method has been proposed to overcome the incompatibilities between the high organic solvent content (45%CH₃OH and 45% CH₃CN) used in the reverse-phase liquid chromatography (LC) separation on one hand and the limitations of the ICP on the other hand. Therefore, several instrument modifications had to be made. For the introduction of the column effluent, a combination of a perfluoroalkoxy LC nebulizer with a PC³ Peltier-cooled inlet system (operated at 2 °C) was used. Additionally, the standard injector tube (internal diameter 2 mm) was replaced by an injector tube with an internal diameter of 1 mm and to avoid carbon build-up on the interface cones and the torch, the nebulizer gas was admixed with 6% v/v of oxygen. After optimization of the method, HPLC-ICP-MS was applied for metabolite profiling of faeces samples after dosing of ¹⁴C-radiolabelled R207910 to dogs and rats. To evaluate the method developed, the HPLC-ICP-MS results were compared with those of HPLC with UV spectrophotometric and ¹⁴C radiochemical detection. As the HPLC-ICP-MS method gave rise to a higher selectivity than HPLC with UV detection and to a better detection limit (5 ng R207910) than the method with radiochemical detection (65 ng R207910), it can be concluded that ICP-MS can be used as a good alternative to the more traditional detection methods, even when a mobile phase with high organic solvent content has to be used in the LC separation.     

Speciation of trace amounts of aluminium in percolating water of forest soil by online coupling HPLC-ICP-MS

Procedures were developed for the speciation of trace amounts of aluminium present in percolating water of forest soil by online coupling of different chromatographic separation methods to an ICP-MS detection system. Inorganic and organic aluminium species were fractionated on a cation exchange column IONPAC CG12 (10-32). Phytotoxic polymeric aluminium hydroxides, as e.g. Al₁₃ (AlO₄Al₁₂(OH)₂₄(H₂O)₁₂ ⁷⁺), were determined using pyrocatechol violet (PCV) as a species dependant complexing reagent prior to the cation exchange step. Size fractionation of the organic aluminium species was obtained by size exclusion chromatography using the columns Superdex-75-HR 10/30 and Superdex-Peptide-HR 10/30. Validation of the speciation procedures proved that online coupling HPLC to the element selective and sensitive ICP-MS detection system leads to low detection limits of 0.3–0.6 μg/L and high precision and reproducibility (1.2–3.5%) of the speciation procedures. Speciation data determined for aluminium in a percolating water of the Zierenberg catchment are given.     

HPLC combined with ICP-MS for the determination of trace amounts of rare earth impurities in high-purity La2O3 by using 2-ethylhexyl hydrogen-2-ethylhexylphosphonate resin as a stationary phase

A new method for the determination of trace rare earth impurities in high-purity La₂O₃ by HPLC combined with ICP-MS is proposed. The chromatographic retention behavior of La and Ce in HPLC was studied with 2-ethylhexyl-hydrogen-2-ethylhexylphosphonate (P507) resin as the stationary phase and inorganic acid (HNO₃) as the mobile phase. The effects of acidity of the mobile phase, flow rate of eluent and column oven temperature on the separation of La and Ce were investigated in detail. The results of the effect of different ratios of La / Ce showed that a favorable separation of La and Ce could be obtained easily and rapidly with the method presented. Compared with the conventional open column method, the proposed separation system shows a good performance with regard to short separation time, low reagent consumption, and simple operation. The method has been applied to the analysis of real samples of high-purity La₂O₃ with satisfactory results.