Spatially focused deposition of capillary electrophoresis effluent onto surface-enhanced Raman-active substrates for off-column spectroscopy

Surface-enhanced Raman scattering (SERS) is employed to obtain distinctive spectra of compounds that are efficiently separated by capillary electrophoresis (CE) and deposited onto planar SERS-active substrates. A simple method is described that explains how to prepare SERS-active substrates by depositing a silver-colloid solution onto frosted-glass microscope slides, using a high-efficiency nebulizer. Scanning electron micrographs reveal a layered coating of fairly uniform-sized, 100-nm silver nanoparticles with interstitial spaces ranging from a few to tens of nanometers. The on-column separation is monitored by laser-induced fluorescence, while electrofilament depositing the CE effluent onto a moving SERS-substrate. Subsequently, the SERS spectra and off-column electropherograms are obtained with a simple confocal Raman spectrometer. The test compounds used to demonstrate this technique include compounds of biological significance: benzyloxyresorufin, riboflavin, and resorufin. CE and Raman conditions are evaluated to determine their affects on the SERS signals. An average off-column efficiency of 100,000 plates/m and a signal reproducibility of 11% relative standard deviation were achieved. Characteristic spectra with major Raman bands exhibiting signal-to-noise ratios of greater than 3 were obtained for a 3.2-nL injection of 10(-6) M (706 fg) resorufin. Forming a self-assembled monolayer (SAM) on the substrate increases the sensitivity of the SERS technique and decreases the on-substrate broadening. Calibration plots for both plain- and SAM-SERS substrates are demonstrated.     

On-column polymer-imbedded graphite inlet electrode for capillary electrophoresis coupled on-line with flow injection analysis in a poly(dimethylsiloxane) interface

A method for coupling an electrophoretic driven separation to a liquid flow, using conventional fused-silica capillaries and a soft polymeric interface is presented. A novel design of the electrode providing high voltage to the electrophoretic separation was also developed. The electrode consisted of a conductive polyimide/graphite imbedded coating immobilized onto the capillary electrophoresis (CE) column inlet. This integrated electrode gave the same separation performance as a commonly used platinum electrode. The on-column electrode also showed good electrochemical stability in chronoamperometric experiments. In addition, with this electrode design, the electrode position relative to the inlet end of the CE column will always be constant and well defined. The on-line flow injection analysis (FIA)-CE system was used with electrospray ionization (ESI)-time of flight (TOF)-mass spectrometry detection. The preparation of the PDMS (poly(dimethylsiloxane)) interface for FIA-CE is described in detail and used for initial tests of the on-column polymer-imbedded graphite inlet electrode. In this interface, a pressure-driven liquid flow, a make up CE electrolyte and a CE column inlet meet in a two-level cross (95 microm ID) in the PDMS structure, enabling independent flow characterization.     

Capillary electrochromatography of biologically relevant flavonoids

Flavonoids were separated utilizing CEC technique. Baseline separation of biologically relevant flavonoids was obtained using a 100 microm ID fused-silica capillary filled with 3 microm Silica-C18 material and an optimized mobile phase comprising of 20 mM Tris-HCl (pH 6.5), ACN and water at a ratio of 10/40/50 v/v/v. Separations were carried out at 25 kV and a column temperature of 25 degrees C. The influence of relevant parameters for the CEC separation, such as buffer concentration, pH, separation voltage, and ACN concentration, was investigated and optimized. Dependencies of the electroendoosmotic flow (EOF) on these parameters and effects on the resolution of the analytes were studied. During analyses the solvents used for dissolving the samples turned out to have significant effects on the separation of flavonoids. The optimized system was then successfully used for the separation of the flavonoids epicatechin, myricetin, quercetin, naringenin, and hesperetin. CEC turned out to be a useful complementary tool for the economic analysis of flavonoids in addition to common HPLC, muHPLC, and CE methodologies. This method can be used for real applications in phytomics.     

Photopolymerized sol-gel frits for packed columns in capillary electrochromatography

Porous sol-gel frits are fabricated in a capillary column by filling it with a solution of 3-(trimethoxysilyl)propyl methacrylate, hydrochloric acid, water, toluene (porogen), and a photoinitiator (Irgacure 1800) and exposing it to UV light at 365 nm for 5 min. The separation column (30 cm x 75 microm I.D.) contains between the inlet and outlet frits a 15-cm packed segment filled with 5-microm silica particles modified with the chiral compound (S)-N-3,5-dinitrobenzoyl-1-naphthylglycine. A detection window (1 mm long) is placed immediately after the outlet frit. To demonstrate the performance of this chiral separation column, mixtures of 16 different amino acids (three of which are not naturally occurring) derivatized with the fluorogenic reagent 4-fluoro-7-nitro-2,1,3-benzoxadiazole were separated by capillary chromatography. The enantiomeric separation of the column results in a resolution ranging from 1.21 to 8.29, and a plate height ranging from 8.7 to 39 microm.     

L-羟脯氨酸寡肽混合物的高效液相色谱分离与质谱分析

研究了三氯氧磷辅助下L-羟脯氨酸的成肽反应,建立了采用反相高效液相色谱-质谱/质谱联用技术分离鉴定羟脯氨酸寡肽混合物的方法,优化了L-羟脯氨酸寡肽混合物的色谱分离条件。实验以YWG C8柱(10 μm,250 mm×10 mm)为分离柱,以乙腈-0.06%三氟乙酸水溶液(体积比为2∶98)为流动相进行等度洗脱,在正离子模式下对洗脱物进行了电喷雾电离串联质谱鉴定。结果显示,分离出的各组分分别为L-羟脯氨酸二肽、L-羟脯氨酸环二肽和L-羟脯氨酸三肽。     

Optimization of GC detector parameters using electronic pressure control

HP 5890 Series II Gas Chromatographs are equipped with prototype hardware enabling electronic pressure programming of all detector and carrier gases. A method of using electronic pressure control (EPC) to optimize detector performance (sensitivity, selectivity, and baseline stability) is demonstrated. With EPC, sample introduction, column separation, and detector performance can be optimized simultaneously without the classical trade-offs in performance. An example is also presented of the use of a new automated system which enables cool on-column injection into 250 or 320 μm columns without the need for a retention gap.     

High performance displacement chromatography of proteins: Separation of β-Lactoglobulins A and B

Summary β-Lactoglobulins A and B were separated by high performance displacement chromatography on an anion-exchanger column with chondroitin sulfate as the displacer. A sample of 100 mg containing a mixture of the two β-lactoglublins was separated on a column of 75×7.5 mm in a single chromatographic run. The separation process followed the rules of the classical displacement development: the two proteins formed contiguous rectangular bands and their concentrations were dependent on the displacer concentration. The results demonstrate that high performance displacement chromatography is a useful technique for the separation of proteins in preparative amounts with columns and instrumentation typically used in analytical HPLC. Furthermore, it has the potential to become the method of choice in large scale separation of proteins.     

Capillary ion chromatography of inorganic anions on octadecyl silica monolith modified with an amphoteric surfactant

A reversed-phase monolithic silica based capillary column (Onyx C(18), 150 mm x 0.1 mm) was modified with the amphoteric surfactant, N-dodecyl-N,N-(dimethylammonio)undecanoate (DDMAU) and evaluated for the separation and determination of inorganic anions using on-column capacitively coupled contactless conductivity detection (C(4)D). The chromatographic performance of the column was evaluated and under optimal conditions separation efficiencies of 56,200 plates per meter or 7025 plates per column (at detection point) were observed (for iodide). Direct plumbing of the capillary column to the micro-injector and on-column detection eliminated extra-column band broadening, thus allowing accurate analysis of van Deemter curves obtained for the monolithic capillary column. The calculated value for the C-term in the obtained van Deemter curve was between 3 and 4 ms for inorganic anions, allowing for the utilisation of relatively high flow rates without significant losses in efficiency. The performance of the C(4)D detector was investigated and compared for detection on an open tubular capillary column and on the modified monolithic silica capillary column. The on-column detection approach did not result in any significant decrease in peak sensitivity for the monolith compared to responses recorded for open tubular capillary columns, and in addition meant the system could be applied to rapid separations by simple variation in apparent column length. The proposed chromatographic system allowed for detection of common anions at sub-ppm level with a 10 nL injection volume. Additionally, on-column detection allowed visualisation of the development of the separation at any point in time and evaluation of the longitudinal uniformity of the ion-exchange coating.     

Comparison of the performance of conventional microparticulates and monolithic reversed-phase columns for liquid chromatography separation of eleven pollutant phenols

The performance of isocratic separations of 11 pollutant phenols (PP) using monolithic (Chromolith RP-18e) and conventional reversed-phase 5 microm (Luna and Purospher C18) and 4 microm (Synergi C12) particulate size columns, selected from high purity silica materials, has been compared. The separations have been optimized based on a previously optimized separation in which a reversed-phase C18 Luna column and acetonitrile as organic modifier were used, allowing the separation of all phenols tested in 23 min. The optimization process was carried out for each column by studying the effect of the mobile phase (acetonitrile as organic modifier, pH, flow-rate) on phenols separation. Under the optimized separation conditions, all phenols were separated in less than 23 min for all columns tested. Asymmetry factors were further evaluated and used to estimate column efficiency using the Dorsey-Foley equation. The efficiency and asymmetry factors were lower for Chromolith than for Purospher and Luna columns respectively. The Chromolith column was finally selected, due to its lower flow resistance, analysis time and good efficiency and asymmetry factors. The PPs separation was achieved in 3 min. The asymmetry factors were in the range 0.9-1.5 using 50mM acetate buffer (pH = 5.25)-ACN (64:36, v/v) as mobile phase, T=45 degrees C and 4.0 ml min(-1) flow-rate.     

Peak broadening in isothermal runs due to large retention gaps in capillary GC?

A simple formula is derived which allows estimation of the band broadening due to longitudinal diffusion in retention gaps for isothermal runs with the column held at the injection temperature. The broadening is strongly dependent on the linear gas velocity in the retention gap. If the internal diameters of the retention gap and the separation column are similar, the retention gap may have a length exceeding 100 m, even if the separation column is only 10 m long. A 0.5 mm I.D. retention gap attached to a 0.3 mm I.D. separation column (of interest for automatic on-column injection) may be several meters long. Retention gaps of 0.3 mm I.D. may be used for on-column injections into separation columns with I.D's. down to about 0.1 mm.     

How to utilize the true performance of monolithic silica columns

Ways of utilizing the true separation efficiency of monolithic silica (MS) columns were studied. The true performance of MS columns, both regular-sized (rod-type clad with PEEK resin, 4.6 mm ID, 10 cm) and capillary sized (in 100 or 200 microm ID fused silica capillary, 25-140 cm) was evaluated by calculating the contribution of extra-column effects. HETP values of 7-9 microm were observed for solutes having retention factors (kvalues) of up to 4 for rod columns and up to 15 for a capillary column. The high permeability of MS columns allowed the use of long columns, with several connected together in the case of rod columns. Narrow-bore connectors gave good results. Peak variance caused by a column connector ranges from 50 to 70% of that caused by one rod-type column for up to three connectors or four columns in 80% methanol, but the addition of a 4th or 5th connector to add a 5th and 6th column, respectively, caused a much greater increase in peak variance, especially for long-retained solutes, which is greater than the variance caused by one rod column. Rod columns seem to show slightly lower efficiency at a pressure higher than 10 MPa or so. The use of acetonitrile-water as a mobile phase better preserved the ability of individual rod columns to generate up to 100,000 theoretical plates with 14 columns connected. Methods for eliminating extra-column effects in micro-HPLC were also studied. Split injection and on-column detection resulted in optimum performance. A long MS capillary measuring 140 cm produced 160,000 theoretical plates. The column efficiency of a capillary column was not affected by the pressure, showing advantages over the rod columns that exhibited peak broadening caused by connectors and pressure.     

工业制备高效液相色谱法制备淫羊藿中的黄酮系列对照品

淫羊藿甙和朝藿定A、B、C是淫羊藿中重要的活性成分,本研究应用工业制备高效液相色谱从淫羊藿粗提物中分离制备了这4个成分。淫羊藿粗提物经大孔吸附树脂粗分离获得相应的组分后,利用工业制备高效液相色谱完成精制纯化。采用自装填Chromatorex C18制备柱(220 mm×77 mm, 10 μm),乙腈-水(26:74或30:70, v/v)为流动相进行洗脱,在35 min内,实现了这4种成分的基线分离及规模制备。从300 g粗提物(总黄酮含量约20%)中获得淫羊藿甙33 g、朝藿定C 4.6 g、朝藿定B 3.7 g和朝藿定A 0.6 g,产品纯度均达到98%以上。此方法通过两步分离即可实现这4种成分的完全分离,具有快速高效、产品纯度高的特点,适于淫羊藿中淫羊藿甙、朝藿定A、B、C系列对照品的规模制备。     

Qualitative evaluation of thermal desorption-programmable temperature vaporization-comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry for the analysis of selected halogenated contaminants

The separation of 38 toxic and predominant polychlorinated biphenyl (PCB) congeners, 11 persistent halogenated pesticides, 1 brominated biphenyl (BB), and 8 polybrominated diphenyl ethers (PBDEs) has been optimized using comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry (GC x GC-TOFMS). A thermal desorption-programmable temperature vaporization (TD-PTV) step was used for the injection. Different column sets were investigated, and a 100% dimethylpolysiloxane (15 m x 0.25 mm i.d. x 0.25 microm film thickness) narrowbore capillary column coupled to a high temperature (8% phenyl)-polycarborane-siloxane (2 m x 0.10 mm i.d. x 0.10 microm film thickness) microbore column set was selected. Of the 58 compounds investigated, only one pair of PCBs was not resolved. All other analytes were either baseline separated into the chromatographic plane or were virtually separated using the deconvolution capability of the TOFMS.     

Optimization of a stability-indicating HPLC method for the simultaneous determination of rifampicin, isoniazid, and pyrazinamide in a fixed-dose combination using artificial neural networks

The aim of this study is to develop and optimize a simple and reliable high-performance liquid chromatography (HPLC) method for the simultaneous determination of rifampicin (RIF), isoniazid (INH), and pyrazinamide (PZA) in a fixed-dose combination. The method is developed and optimized using an artificial neural network (ANN) for data modeling. Retention times under different experimental conditions (solvent, buffer type, and pH) and using four different column types (referred to as the input and testing data) are used to train, validate, and test the ANN model. The developed model is then used to maximize HPLC performance by optimizing separation. The sensitivity of the separation (retention time) to the changes in column type, concentration, and type of solvent and buffer in the mobile phase are investigated. Acetonitrile (ACN) as a solvent and tetrabutylammonium hydroxide (tBAH), used to adjust pH, have the greatest influence on the chromatographic separation of PZA and INH and are used for the final optimization. The best separation and reasonably short retention times are produced on the micro-bondapak C18, 4.6 x 250-mm column, 10 microm/125 A using ACN-tBAH (42.5:57.5, v/v) (0.0002M) as the mobile phase, and optimized at a final pH of 3.10.     

Facile and sensitive method for the determination of mesna in plasma by high-performance liquid chromatography with ultraviolet detection

The use of 2-chloro-1-methylquinolinium tetrafluoroborate, an ultraviolet tagging reagent, for the ion-pair, reversed-phase high-performance liquid chromatography of mesna in human plasma is reported. In order to achieve this objective optimization of the two-step procedure, derivatization and separation of mesna S-quinolinium derivative from that of other thiols present in plasma and internal standard, was investigated. The derivatization was optimized in terms of pH, reagent excess and time of the reaction, and the mobile phase in terms of ion-pairing reagent concentration, pH, organic modifier content and temperature. Baseline separation was achieved on an analytical Waters Nova-Pak C18 (150x3.9 mm, 5 microm) column with a mobile phase consisting of pH 2.3 0.05 M trichloroacetic acid-acetonitrile (89:11, v/v) pumped at 1.2 ml/min. The peak height ratios of the mesna derivative to that of the internal standard (thiomalic acid) varied linearly with the concentration of the analyte added to normal plasma with a correlation coefficient of 0.9997. The lower limits of detection and quantitation were 40 pmol/ml (0.8 pmol on-column) and 160 pmol/ml (3.2 pmol on-column), respectively. The intra-run imprecision and inaccuracy were from 1.3 to 2.4 and from 1.3 to 2.0%, respectively.     

Capillary electrochromatography-mass spectrometry for the separation and identification of isomeric polyaromatic hydrocarbon DNA adducts derived from in vitro reactions

Capillary electrochromatography (CEC) is an emerging technique that combines features of both micro-capillary high-performance liquid chromatography (microHPLC) and capillary electrophoresis (CE). This separation technique possesses high speed and the efficiency of an electro-driven system, while the selectivity and sample loadability compare to those of a packed capillary LC column. Since the separation mechanism is based on that of HPLC, the concept of isoeluotropic strength and selectivity of solvents as well as the on-column focusing techniques for sample introduction used in LC can be applied in CEC. This article examines some of these features of CEC in the context of our own experiences with the technique. More specifically, emphasis is placed on applications of CEC to the analysis of DNA adducts of polyaromatic hydrocarbons by coupling CEC to mass spectrometry. It is shown that, with proper selection of mixed organic modifiers in the mobile phase, i.e. ternary and quaternary mobile phases, complex DNA adduct mixtures derived from in vitro reactions can be separated isocratically with improved selectivity and much greater speed than by HPLC. Additionally, the speed of the analysis is further enhanced by employing a step gradient. Furthermore, CEC may be easily coupled to mass spectrometry such that the characterization of each isolated component from the mixtures is performed on-line with the separation. By using on-column focusing, the sample loadability onto a CEC column is improved.     

Separation and determination of 10-hydroxy-2-decenoic acid in royal jelly by capillary electrophoresis

Summary The application of capillary electrophoresis (CE) to the separation and determination of the active ingredient, 10-hydroxy-2-decenoic acid, in royal jelly with direct on-column UV detection at 214 nm is described. Using a cathodic injection and anodic detection scheme, 10-hydroxy-2-decenoic acid (10-HDA) was separated and detected in less than 10 min in a fused silica capillary column with a phosphate buffer at pH 7.3 with an applied voltage of 20 KV followed by direct UV detection. The use of cetyltrimethylammonium bromide (CTAB) as electroosmotic flow modifier allows the rapid separation of 10-HDA from other constituents in royal jelly by reversing the direction of electroosmotic flow. The influence of organic solvents in the electrolyte on separation selectivity is also discussed.     

On-chip temperature gradient interaction chromatography

This paper reports the first integrated microelectromechanical system (MEMS) HPLC chip that consists of a parylene high-pressure LC column, an electrochemical sensor, a resistive heater and a thermal-isolation structure for on-chip temperature gradient interaction chromatography application. The separation column was 8 mm long, 100 microm wide, 25 microm high and was packed with 5 microm sized, C18-coated beads using conventional slurry-packing technique. A novel parylene-enhanced, air-gap thermal isolation technology was used to reduce heater power consumption by 58% and to reduce temperature rise in the off-column area by 67%. The fabricated chip consumed 400 mW when operated at 100 degrees C. To test the chromatography performance of the fabricated system, a mixture of derivatized amino acids was chosen for separation. A temporal temperature gradient scanning from 25 to 65 degrees C with a ramping rate of 3.6 degrees C/min was applied to the column during separation. Successful chromatographic separation of derivatized amino acids was carried out using our chip. Compared with conventional temperature gradient HPLC system which incorporates "macro oven" to generate temporal temperature gradient on the column, our chip's thermal performance, i.e., power consumption and thermal response, is greatly improved without sacrificing chromatography quality.     

A new type of capillary column for open-tubular electrochromatography

A new type of open-tubular C(18) ester-bonded electrochromatographic column was prepared with sol-gel technology, followed by an on-column octadecyl silylation reaction. Glycidoxypropyltrimethoxysilane, a widely used and important silane agent, was used as the sol-gel precursor to form a thin coating layer on the wall of the fused-silica capillary. The C(18) groups were introduced into the coating layer by on-column esterification reaction with stearic acid. The electrochromatography behavior of the column was evaluated in terms of the separation of peptides. A high efficiency of 4.8x10(5) plates/m was achieved for a basic pentapeptide using the C(18 )ester-bonded column. In comparison with bare capillaries and glycidoxypropyltrimethoxysilane sol-gel-coated capillaries, the C(18) ester-bonded column showed the best separation of a mixture of seven pentapeptides under identical conditions of buffer, pH, and applied voltage.     

Simultaneous determination of palladium, platinum, rhodium and gold by on-line solid phase extraction and high performance liquid chromatography with 5-(2-hydroxy-5-nitrophenylazo)thiorhodanine as pre-column derivatization regents

In this paper, 5-(2-hydroxy-5-nitrophenylazo)thiorhodanine (HNATR) was synthesized. A new method for the simultaneous determination of palladium, platinum, rhodium and gold ions as metal-HNATR chelates was developed using a rapid analysis column high performance liquid chromatography equipped with on-line solid phase extraction technique. The samples (Water, human urine, geological samples and soil) were digested by microwave acid-digestion. The palladium, platinum, rhodium and gold ions in the digested samples were pre-column derivatized with HNATR to form colored chelates. The Pd-HNATR, Pt-HNATR, Rh-HNATR and Au-HNATR chelates can be absorbed onto the front of the enrichment column when they were injected into the injector and sent to the enrichment column [Zorbax Stable Bound, 10 mm x 4.6 mm, 1.8 microm] with a buffer solution of 0.05 mol L(-1) phosphoric acid as mobile phase. After the enrichment had finished, by switching the six ports switching valve, the retained chelates were back-flushed by mobile phase and travelling towards the analytical column. These chelates separation on the analytical column [Zorbax Stable Bound, 10 mm x 4.6 mm, 1.8 microm] was satisfactory with 72% acetonitrile (containing 0.05 mol L(-1) of phosphoric acid and 0.1% of Triton X-100) as mobile phase. The palladium, platinum, rhodium and gold chelates were separated completely within 2.5 min. Compared to the routine chromatographic method, more then 80% of separation time was shortened. By on-line solid phase extraction system, a large volume of sample (10 mL) can be injected, and the sensitivity of the method was greatly improved. The detection limits (S/N=3, the sample injection volume is 10 mL) of palladium, platinum, rhodium and gold in the original samples reaches 1.4, 1.8, 2.0 and 1.2 ng L(-1), respectively. The relative standard deviations for five replicate samples were 2.4-3.6%. The standard recoveries were 88-95%. This method was applied to the determination of palladium, platinum, rhodium and gold in human urine, water and geological samples with good results.