军用化工企业含氮废水处理工艺研究

采用厌氧——缺氧——SBR微生物生化处理组合工艺,研究了双基（含双基混合酯）球扁药含氮废水处理技术,通过菌种驯化,实现了高盐浓度、高CODCr含量废水经处理后达标排放,CODCr的总去除率达到97．7％,质量浓度降到96mg／L;BOD5总去除率达到了98．O％,质量浓度降到28mg／L;SS的总去除率达到94．4％,质量浓度降到了9mg／L。     

Fenton-UASB-生物接触氧化处理Fischer-Tropsch合成废水的研究

用Fenton-UASB-生物接触氧化组合工艺对Fischer-Tropsch合成废水进行处理。实验结果表明,采用Fenton法对废水进行预处理,在pH值为3,H2O2的投加量为30 mL/L,Fe2+投加量为1.2 g/L,反应时间为120 min时,去除了63%的CODCr,有效地提高了废水的可生化性;Fenton预处理出水经UASB厌氧生物处理后,CODCr去除率达90%以上;最后经接触氧化后,出水CODCr达100 mg/L以下,达到了GB8978-1996《污水综合排放标准》中化工类废水的二级排放标准。     

Ti/Sb2O5-SnO2/PbO2电极电催化氧化对氨基苯酚

以电沉积法制备的Ti／Sb2O5-SnO2／PbO2电极作阳极,恒电流电解水溶液中的对氨基苯酚（PAP）,利用紫外光谱探讨了对氨基苯酚电催化氧化的反应历程,系统地考察了电解时间、反应温度,pH值、电流密度以及对氨基苯酚初始浓度对COD去除率的影响,提出了电催化氧化对氨基苯酚的最佳条件．结果表明,对氨基苯酚电催化反应为逐级氧化历程,主要中间产物为苯醌、丁烯二酸和草酸,最终产物为CO2和水．20℃,对初始浓度10mg／L的对氨基苯酚水溶液（pH=6）,恒定电流密度100mA／cm^2,电解1h,COD去除率可达98．5％．该方法作为废水中对氨基苯酚的最小化处理．具有良好的应用前景．     

大孔吸附树脂处理含磺胺废水的研究

利用大孔吸附树脂处理含磺胺废水。实验表明，DRHⅢ树脂对磺胺具有良好的吸附－解吸效果。原废水中磺胺浓度约为17.2g/L,COD约为13750mg/L，经树脂吸附处理后，废水中COD去除率约86％，磺胺的吸附率88．2％，树脂的解吸率为97．5％，磺胺的回收率约86．0％，其纯度达99．8％。在废水有效处理的同时实现了废物资源化，具有良好的环境效益和较高的经济效益。     

树脂吸附法处理水杨酸甲酯生产废水的研究

采用吸附树脂NDA—99处理水杨酸甲酯生产废水，结果表明该树脂时废水中的5磺基水杨酸及水杨酸均具有良好的吸附—脱附性能．废水经预处理和吸附处理后，CODCr由57000-59000mg／L降至6300mg／L左右，去除率接近89％．用IBV8％NaOH 3BVH2O作脱附剂，在温度为60℃、流量为IBV／h的条件下，脱附率接近100％，树脂可重复使用．高浓度脱附液经酸化、浓缩、冷却结晶，可回收5—磺基水杨酸，回收率为95％左右。纯度为78％。     

两性田菁胶在处理生活污水中的助凝作用

研究了以聚合硫酸铁为主凝剂、两性田菁胶(ASG)为助凝剂处理城市生活废水的各种影响因素.实验结果表明:聚合硫酸铁和两性田菁胶分别以200mg/L和10mg/L的复配浓度、pH值接近7时混凝效果最佳,CODCr去除率达到近80%,处理后废水CODCr达到国家排放标准.     

树脂吸附法处理高浓度DSD酸氧化工序生产废水的研究

本文采用大孔吸附树脂固定床工艺处理DSD酸氧化工序生产废水。实验结果表明，ND804大孔吸附树脂对该废水具有良好的吸附－脱附效果，废水经ND804树脂吸附处理后，CODCr由14790mg/L降至1300mg/L左右，COD去除率约为91％，并可回收纯度达80％的DNS酸，废水在得到有效治理的同时实现了废物的资源化。     

Ti/RuO2-CoO电极制备及其氨氮降解性能

采用热氧化法制备Ti/RuO_2-CoO电极,通过SEM和XRD对电极涂层的表面形貌和晶体结构进行表征;并利用最佳条件制备的电极开展电化学氧化氨氮模拟废水研究。实验研究了电流密度、初始pH值、Cl~-浓度和NH_3-N初始浓度对NH_3-N降解效果的影响。研究结果表明:当n(Ru)/n(Co)=7∶3时Ti/RuO_2-CoO电极对NH_3-N的去除效果较好。随着电流密度的增加,NH_3-N去除率随之升高;初始pH为碱性条件时,NH_3-N去除效果较好;NH_3-N去除率随Cl~-浓度的增加呈现先增大后减小,当Cl~-浓度为3 000 mg/L时,氨氮去除率达到97.95%。当电流密度为70 mA/cm~2、Cl~-浓度为3 000 mg/L、初始pH=9时,经过180 min电解后,氨氮初始浓度从500 mg/L降低至10.25 mg/L,且电化学氧化氨氮的产物主要为氮气和硝酸盐氮。     

6-氨基青霉烷酸生产废水的厌氧和深度处理研究

针对6-氨基青霉烷酸生产废水的高污染物浓度、高硫酸根、难降解物质多的特点,对废水经过硫酸根预处理,稀释3倍和6倍后,废水对厌氧污泥没有急毒性,厌氧污泥可以逐步适应废水环境。经过厌氧处理以及后续的Fenton深度处理,高浓度的6-氨基青霉烷酸生产废水CODCr可由45450mg/L降到255mg/L,出水CODCr可达到污水三级排放标准。     

镀铜铁屑-H_2O_2催化氧化降解含酚废水

采用镀铜铁屑代替传统Fenton体系中的FeSO4作为催化剂,通过改变H2O2与镀铜铁屑的投加量、溶液的pH值、反应温度、反应时间等条件,研究了该体系对处理苯酚废水的影响。结果表明,常温下处理实际含酚印染废水,在pH值为4~6,30%H2O2 12mL/L,镀铜铁屑5g/L,反应时间为45min时,COD去除率可达96%,其CODCr从5827mg/L降至419mg/L,色度从2000降至30,符合国家三级排放标准。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.