Gas–liquid partition coefficients and Henry's law constants of methyl mercaptan in aqueous solutions of Fe(II)–CDTA chelate complex

Utilization of ferric chelate complex of trans-1,2-cyclohexanediaminetetraacetic acid (CDTA) for the oxidative scrubbing of H₂S and CH₃SH in Kraft mill streams can be beneficial from the standpoints of iron protection against precipitation and oxygen-mediated regenerative oxidation of the ferrous chelate CDTA. The physical solubility of methyl mercaptan in CDTA–Fe(III) complex cannot be measured directly because of oxidation of the sulfur-bearing gaseous species with the ferric chelate. Therefore, this investigation was carried out to determine the gas–liquid partition coefficients and Henry's law constants of methyl mercaptan in aqueous iron-free CDTA solutions and non-reacting ferrous chelate solutions (CDTA–Fe(II) complex), using the static headspace method with an estimated accuracy of about 2%. Experiments with aqueous solutions of chelate concentrations varying between 38 and 300 mol m⁻³ were carried out at temperatures between 298 and 333 K and atmospheric pressure. It was shown that the methyl mercaptan solubility decreases with increasing temperature for all systems but was not much influenced, in the studied conditions, by the chelate concentration especially at larger temperatures.     

Ionic medium effects on equilibrium constants Part I. Proton, copper(II), cadmium(II), lead(II) and acetate activity coefficients in aqueous solution

The molar single ion activity coefficients associated with hydrogen, copper(II), cadmium(II) and lead(II) ions were determined at 25 degrees C and ionic strengths between 0.100 and 3.00 M (NaClO4), whereas for acetate the ionic strengths were fixed between 0.300 and 2.00 M, held with the same inert electrolyte. The investigation was carried out potentiometrically by using proton-sensitive glass, copper, cadmium and lead ion-selective electrodes and a second-class Hg|Hg2(CH3COO)2 electrode. It was found that the activity coefficients of these ions (y(i)) can be assessed through the following empirical equations: log y(H) = -0.542I(0.5) + 0.451I; log y(Cu) = -1.249I(0.5) + 0.912I; log y(Cd) = -0.829I(0.5) + 0.448I(1.5); log y(Pb) = -0.404I(0.5) + 0.117I(2); and log y(Ac) = 0.0370I     

Prediction of n-octanol/water partition coefficients and acidity constants (pKa) in the SAMPL7 blind challenge with the IEFPCM-MST model

Within the scope of SAMPL7 challenge for predicting physical properties, the Integral Equation Formalism of the Miertus-Scrocco-Tomasi (IEFPCM/MST) continuum solvation model has been used for the blind prediction of n-octanol/water partition coefficients and acidity constants of a set of 22 and 20 sulfonamide-containing compounds, respectively. The log P and pK_a were computed using the B3LPYP/6-31G(d) parametrized version of the IEFPCM/MST model. The performance of our method for partition coefficients yielded a root-mean square error of 1.03 (log P units), placing this method among the most accurate theoretical approaches in the comparison with both globally (rank 8th) and physical (rank 2nd) methods. On the other hand, the deviation between predicted and experimental pK_a values was 1.32 log units, obtaining the second best-ranked submission. Though this highlights the reliability of the IEFPCM/MST model for predicting the partitioning and the acid dissociation constant of drug-like compounds compound, the results are discussed to identify potential weaknesses and improve the performance of the method.

     

Bicyclic and acyclic diamides: comparison of their aqueous phase binding constants with Nd(III), Am(III), Pu(IV), Np(V), Pu(VI), and U(VI)

This report describes affinity measurements for two, water-soluble, methyl-alkylated diamides incorporating the malonamide functionality, N,N,N',N' tetramethylmalonamide (TMMA) and a bicyclic diamide (1a), toward actinide metal cations (An) in acidic nitrate solutions. Ligand complexation to actinides possessing oxidation states ranging from +3 to +6 was monitored through optical absorbance spectroscopy, and formation constants were obtained from the refinement of the spectrophotometric titration data sets. Species analysis gives evidence for the formation of 1, 4, 1, and 2 spectrophotometrically observable complexes by TMMA to An(III, IV, V, and VI), respectively, while for 1a, the respective numbers are 3, 4, 2, and 2. Consistent with the preorganization of 1a toward actinide binding, a significant difference is found in the magnitudes of their respective formation constants at each complexation step. It has been found that the binding affinity for TMMA follows the well-established order An(V) < An(III) < An(VI) < An(IV). However, with 1a, Np(V) forms stronger complexes than Am(III). The complexation of 1a with Np(V) and Pu(VI) at an acidity of 1.0 M is followed by reduction to Np(IV) and Pu(IV), whereas TMMA does not perturb the initial oxidation state for these dioxocations. These measurements of diamide binding affinity mark the first time single-component optical absorbance spectra have been reported for a span of actinide-diamide complexes covering all common oxidation states in aqueous solution.     

Determination of particle size in aqueous suspensions of hydrogels of iron(III), indium(III), aluminum, chromium(III), titanium(IV), and zirconium(IV) oxohydroxides

Dispersion of hydrogels of Fe^III, In^III, Al^III, Cr^III, Ti^IV, and Zr^IV oxohydroxides in an aqueous medium was studied by sedimentation analysis. The hydrogel dispersion depends on the metal nature, pH of precipitation, and suspension concentration. The systems are predominantly polydisperse, and the gel particle size ranges from 2 to 140 μm. The data obtained suggest that the gel particles are formed by three-dimensional networks consisting of polymeric chains metal-oxygen and contain cavities filled with water. __________ Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 1083–1088, May, 2005.     

Vapor pressures,osmotic and activity coefficients for (LiBr + acetonitrile) between the temperatures (298.15 and 343.15) K

Precise vapor pressure data for pure acetonitrile and (LiBr + acetonitrile) are given for temperatures ranging from T=(298.15 to 343.15) K. The molality range is from m=(0.0579 to 0.8298) mol · kg⁻¹. The osmotic coefficients are calculated by taking into account the second virial coefficient of acetonitrile. The parameters of the extended Pitzer ion interaction model of Archer and the mole fraction-based thermodynamic model of Clegg–Pitzer are evaluated. These models accurately reproduce the available osmotic coefficients. The parameters of the extended Pitzer ion interaction model of Archer are used to calculate the mean molal activity coefficients.     

An advanced gas/vapor permeation system for barrier materials: Design and applications to poly(ethylene terephthalate)

A new gas/vapor mixture permeation system is described to investigate the effect of organic molecules on oxygen (O₂) and carbon dioxide (CO₂) transport in barrier materials. Methanol vapor was considered as a flavor simulant mainly because of its conveniently high diffusion coefficient, which makes the experimental time accessible. A highly accurate syringe pump was used to introduce a desired activity level of vapor into gas feed stream. Adsorption of methanol on high energy surfaces is carefully characterized to prevent underestimation of methanol permeability. A special permeation cell was also developed to study the effect of interacting vapors on O₂ and CO₂ transport in barrier materials. Systematic permeation measurements were conducted for binary and ternary gas/vapor permeation measurements (e.g., MeOH/O₂ and O₂/CO₂/MeOH) to verify the feasibility of our new vapor/gas permeation system. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Benchmarking NMR indirect nuclear spin-spin coupling constants: SOPPA, SOPPA(CC2), and SOPPA(CCSD) versus CCSD

Accurate calculations of NMR indirect nuclear spin-spin coupling constants require especially optimized basis sets and correlated wave function methods such as CCSD or SOPPA(CCSD). Both methods scale as N(6), where N is the number of orbitals, which prevents routine applications to molecules with more than 10-15 nonhydrogen atoms. We have therefore developed a modification of the SOPPA(CCSD) method in which the CCSD singles and doubles amplitudes are replaced by CC2 singles and doubles amplitudes. This new method, called SOPPA(CC2), scales only as N(5), like the original SOPPA-method. The performance of the SOPPA(CC2) method for the calculation of indirect nuclear spin-spin coupling constants is compared to SOPPA and SOPPA(CCSD) employing a set of benchmark molecules. We also investigate the basis set dependence by employing three different basis sets optimized for spin-spin coupling constants, namely the HuzIV-su4, ccJ-pVTZ, and ccJ-pVQZ basis sets. The results of the corresponding CCSD calculations are used as a theoretical reference.     

Determination of arsenite, arsenate and monomethylarsonic acid in aqueous samples by gas chromatography of their 2,3-dimercaptopropanol (bal) complexes

Procedures are described for the determination of arsenite, arsenate and monomethylarsonic acid in aqueous samples. The arsenicals (after reduction of arsenic to the tervalent state) readily react with 2,3-dimercaptopropanol (BAL) to yield their BAL complexes. The products are extracted with benzene and introduced into a gas Chromatograph equipped with a flame-photometric detector for sulphur. One aliquot of sample is treated with stannous chloride solution and potassium iodide solution to reduce arsenate and monomethylarsonic acid, then BAL is added and the complexes are extracted with benzene. The extract is analysed for total inorganic As plus monomethylarsonic acid. Magnesia mixture and phosphate solution are added to another aliquot to remove arsenate by co-precipitation with magnesium ammonium phosphate. The precipitate is filtered off and arsenite determined in the filtrate. The detection limits are 0.02 ng of As for arsenate and arsenite and 0.04 ng of As for monomethylarsonic acid.     

Determination of (-)-bunolol and its metabolite, dihydro-(-)-bunolol, in human aqueous humour by gas chromatography-negative ion chemical ionisation mass spectrometry.

(-)-Bunolol (LB) was applied to the human eye in a commercially available eye drop formulation. LB and its metabolite, dihydro-(-)-bunolol (DHLB) were identified and quantified in human aqueous humour. The compounds were analysed as their trimethylsilyl-pentafluorobenzamide derivatives using gas chromatography-negative ion chemical ionisation mass spectrometry. In the case of DHLB the corresponding 2H3-labelled isotopomers were used as internal standards and LB was quantified against its methoxime derivative. Calibration curves for LB and DHLB against internal standards were linear with correlation coefficients 0.994 and 0.996, respectively. Replicate analyses of a pooled sample of aqueous humour containing LB and DHLB gave standard errors of the mean of +/- 9.8 and +/- 2.4% for the concentrations of LB and DHLB, respectively. The practical limit of detection of the method was ca. 30 pg for LB and ca. 100 pg for DHLB. The derivatization procedure was also satisfactory for the analysis of a number of other beta-blockers which are used in ophthalmological practice.     

Studies on the extraction behavior of Zr(IV), Ce(III), Th(IV) and U(VI) from aqueous solutions of Arsenazo-I with HDEHP,HTTA, TDA and TCMA

The extraction behavior of Zr(IV), Ce(III), Th(IV) and U(VI) from aqueous solutions containing Arsenazo-I with the organic solvents tridodecylamine (TDA), 1-[thenoyl-(2)]-3-3-3-trifluoroacetone (HTTA), di(2-ethylhexyl) phosphoric acid (HDEHP) and tricaprylmethylammonium chloride (TCMA) in xylene has been investigated. Effect of hydrogen ion concentration in the aqueous phase, Arsenazo-I concentration, as well as the effect of solvent concentration on the extraction was studied. Some alternatives for separation of the elements studied were recommended enabling the spectrophotometric determination of these elements using Arsenazo-I without interference.     

SACM/CT Study of the dissociation/recombination dynamics of hydrogen peroxide on an ab initio potential energy surface. Part II. Specific rate constants k(E,J), thermal rate constants k infinity(T), and lifetime distributions

Statistical adiabatic channel model/classical trajectory (SACM/CT) calculations of the dissociation/recombination dynamics of hydrogen peroxide, H(2)O(2) <--> 2HO, have been performed on an ab initio potential energy surface by Kuhn, Rizzo, Luckhaus, Quack, and Suhm (J. Chem. Phys. 1999, 111, 2565). Specific rate constants k(E,J), thermal rate constants k(infinity)(T), and lifetime distributions are determined. After averaging over J, the derived k(E,J) are in quantitative agreement with non-exponential time-profiles of HO formation recorded after overtone excitation of H(2)O(2) near the dissociation threshold by Scherer and Zewail (J. Chem. Phys. 1987, 87, 97). The thermal high pressure rate constants for HO recombination agree with experimental data as well and can be represented by k(rec,infinity)/10(-10) cm(3) molecule(-1) s(-1) approximately [0.376 (298 K/T)(0.47) + 0.013 (T/298 K)(0.74)] over the range 60-1500 K. Non-statistical lifetime distributions are suggested not to have been of major relevance for the available experiment.     

Determination of Michaelis-Menten and inhibitor constants by an open-closed flow injection approach (Application to the alkaline phosphatase/theophylline system)

An automatic method for the estimation of Michaelis-Menten and inhibitor constants in biochemical systems was developed using an unsegmented open-closed flow manifold, and the Lineweaver-Burk and Dixon plot methods. The methods were applied to both the determination of K(m) of the enzymatic reaction catalyzed by bovine alkaline phosphatase using 4-methylumbelliferone phosphate as substrate, and the determination of the K(i) constant from theophylline as an inhibitor of this biochemical system. The data treatment and comparative results are presented. The values obtained agree with those provided by a conventional method with the biocatalyst in solution.     

Properties of the CdSe(0001), (0001), and (1120) single crystal surfaces: Relaxation, reconstruction, and adatom and admolecule adsorption

Details of the chemical mechanism underlying the growth of colloidal semiconductor nanocrystals remain poorly understood. To provide insight into the subject, we have preformed a comprehensive study of the polar (0001) and (0001) and nonpolar (1120) wurtzite CdSe surfaces that are exposed during crystal growth using first-principles density functional theory (DFT-GGA) calculations. Stabilization of these surfaces by relaxation and reconstruction was considered. Two particular reconstructions of the polar surfaces were examined: vacancy formation on a 2 x 2 unit cell and addition of Se and Cd atoms on the (0001) and (0001) surfaces, respectively. Calculation results indicate that the (1120) is the most stable surface when compared to the two polar surfaces. Furthermore, reconstructions of the (0001) surface are energetically favored when compared to reconstructions of the (0001) facet. Adsorption of Cd and Se atoms and the CdSe molecule on the three relaxed surfaces and two reconstructed (0001) surfaces were also investigated. Several binding sites were considered to determine the most stable binding geometries and energetics. Atomic species preferentially bind in either 2-fold or 3-fold sites, while the CdSe molecule binds parallel to the surface on all of the considered surfaces. Vibrational frequencies of the adspecies were calculated for the most stable binding configurations and were included in the zero point energy correction. Diffusion barriers for the atomic and molecular species were estimated where possible to be between 0.2 and 0.4 eV on the three relaxed surfaces. Thermochemistry of the CdSe molecule binding and dissociation was also investigated. On all considered surfaces, dissociation is preferred to desorption with dissociation only exothermic on the (0001) surface. Comparison of the three relaxed and two reconstructed surfaces indicates that CdSe molecule binding and dissociation is thermodynamically favored on the (0001) surface. This implies that under a reaction-controlled regime, the rate of homoepitaxy would be faster on the (0001) Se terminated surface than on the (0001) and (1120) surfaces, making the (0001) surface of a nanocrystal the primary direction of growth.     

Determination of trace elements in manganese metal and compounds by ion-exchange chromatography and atomic absorption spectrometry : part 2. Determination of Bi,Cd, In,Zn, Pb,Fe(III), Ga,Cu(II), Co and U(VI)

Traces of the specified elements are separated from 1 g of manganese (II), using a 30- g column of AG50W-X8 cation-exchange resin and mixtures of hydrochloric acid and acetone as eluents. The trace elements are separated into three groups and are determined by atomic absorption spectrometry, except uranium for which spectrophotometry is used. Recoveries for 10 μg amounts (20 μg for gallium) vary between 94% (for gallium) and 103% (for uranium). A combined elution curve, results for the analysis of synthetic mixtures and for the determination of ten trace elements in samples of manganese metal, chloride and dioxide are presented.     

Bioactive mono/bis (carboxyamide) based Co (II), Ni (II) and Cu (II) complexes: Synthesis,Characterization, DNA binding and Anticancer Potentials

Bioactive carboxyamide ligated Cu^II ( 1 ), Co^II ( 2 ) and Ni^II ( 3 ) complexes have been synthesized and characterized using various physico‐chemical techniques. In particular, the occurred slightly distorted square planar geometry in complex 1 was confirmed by single X‐ray crystal structure. Their ( 1 , 2 and 3 ) potential interactions with herring sperm DNA (HS‐DNA) have been investigated using spectral and electrochemical techniques. All these studies suggested that the complex 1 could partially penetrated in the sugar phosphate backbone and stacked in between the DNA base pairs, while the other complexes 2 & 3 could bound only on the grooves of HS‐DNA due to their bi‐ligated architecture around the metal centre. The potent cytotoxicity of L and its complexes 1–3 was also evaluated against AGS human gastric cancer cells. Hoechst 33342/PI double staining images revealed that the complexes significantly induced cell death through apoptosis. In vivo administration of complex 1 remarkably inhibits the tumor growth in male Swiss albino mice, moreover it did not show any hepatotoxicity in mice. All these observed results suggested that these complexes may utilized as good conventional therapeutic agents in the near feature after a series of biological assessments.