Hydrazine‐functionalized latexes

The noncommercial functional monomer 4‐vinylbenzyl hydrazine (VBH) was synthesized and subsequently copolymerized with styrene (St) by means of different batch and semicontinuous seeded emulsion polymerization processes, so as to obtain hydrazine‐functionalized nanoparticles. The effect of pH, surfactant and initiator amounts, ratio VBH/St, reaction temperature, and ratio acetone/water were studied. Due to the amphiphilic character of VBH at acid pH, the hydrazine groups of the functionalized comonomer were masked with acetone to form hydrazone groups. Secondary nucleations were avoided by using the protected VBH comonomer; however, a decreased radical efficiency achieving limited conversion was observed. Controlling the cationic initiator concentration, complete conversions together with the neat growth of the seed particles were obtained in the semicontinuous seeded emulsion polymerization of styrene and VBH protected with acetone. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6201–6213, 2009     

Graft polymerization of epoxide and alternating graft copolymerization of epoxide–acid anhydride onto a polystyrene backbone having an aminimide moiety

Graft polymerization of glycidyl phenyl ether (GPE) and alternating graft copolymerization of GPE–succinic anhydride (SA) onto a polymer‐supported aminimide were examined. The polymer‐supported aminimide was synthesized by radical polymerization of 1,1‐dimethyl‐1‐(2‐hydroxy‐3‐(4‐vinylbenzyloxy)propyl)amine 2‐benzoylimide, which was prepared by the reaction of methyl benzoate with equimolar amounts of 1,1‐dimethyl hydrazine and 4‐glycidylmethylstyrene. This aminimide could initiate the polymerization of GPE and alternating copolymerization of GPE with SA to give the corresponding graft copolymers. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1041–1048, 1999     

Polybenzoxazine resins: Aspects of interaction and adsorption behavior

The technique of inverse gas chromatography (IGC) has been used to evaluate the acid–base interaction potential of two polybenzoxazines. One of these, prepared from bisphenol‐A monomer, was shown to be a net base. Another based on dihydroxybenzophenone registered as a net acid. The bisphenol‐A version was adsorbed at controlled thicknesses on α‐alumina, on fumed silica and on boron nitride, all three solids with acidic surfaces as shown by IGC data. Thin layers of the adsorbed polymer near monolayer coverage were strongly perturbed by the underlying substrate, the polymer surface now behaving as a net acid. Thicker layers of the adsorbed polymer revert to basicity, but fail to attain the acid–base interaction constants of the pure polymer. The presence of strongly interactive substrates leads to the creation of a substantial interphase, the interaction properties of the adsorbed polymer varying through the thickness of this layer. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1441–1447, 1999     

Modeling inverse microemulsion polymerization

A mathematical model for inverse microemulsion polymerization has been developed. The model has been used to fit experimental results of the effect of initiator concentration, light intensity, emulsifier concentration, and dispersed phase weight fraction on the monomer conversion evolution, particle size, and polymer molecular weight in the inverse microemulsion polymerization of 2-methacryloyl oxyethyl trimethyl ammonium chloride (MADQUAT) initiated by UV light in the presence of AIBN. A good fitting of the experimental data was achieved. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2167–2178, 1999     

Small‐angle X‐ray scattering from poly(methylmethacrylate) in aqueous solutions of t‐butyl alcohol

Segment‐segment interaction of poly(methylmethacrylate) in t‐butyl alcohol‐water mixtures in poor solvent regime was studied. From the small‐angle X‐ray scattering measurements of semidilute solution range, the binary and ternary cluster integrals of polymer segments were determined from concentration dependence of the correlation length at various temperatures just above the upper critical solution temperature. We have calculated the contributions of the segment–segment interaction to the entropy and enthalpy from the measured temperature dependence of these interaction parameters and found that both quantities are negative and decrease with decreasing t‐butyl alcohol content. FT‐IR absorption peak of carbonyl group of poly(methylmethacrylate) shifts to the lower frequency with increasing water content. The implications of these findings are discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2195–2199, 1999     

Cure kinetics of biphenyl epoxy‐phenol novolac resin system using triphenylphosphine as catalyst

The effects of the concentration of triphenylphosphine as a catalyst on the cure reaction of the biphenyl epoxy/phenol novolac resin system were studied. The kinetic study was carried out by means of the analysis of isothermal experiments using a differential scanning calorimeter. All kinetic parameters including the reaction orders, activation energy and kinetic rate constants were evaluated. To describe the cure reaction with the catalyst concentration, the normalized kinetic model was developed. The suggested kinetic model with a diffusion term was successfully able to describe and predict the cure reaction of epoxy resin compositions as functions of the catalyst content and temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 713–720, 1999     

Calculation and experimental verification of concentration profiles for selected species at the interphase generated by diffusion in polymer pairs

A method for calculating diffusion rates for individual species in concentrated regime is outlined. The effects of monomeric friction coefficient, Flory–Huggins thermodynamic interaction parameter, individual species molecular weights, local molecular weights distribution, and local T_g are precisely calculated. The method is used to calculate individual concentration profiles generated by diffusion of multicomponent polymer blends, and experimentally tested. Polystyrene with a bimodal molecular weight distribution is allowed to diffuse in a blend of polyphenylene oxide and polystyrene. Local physical properties change markedly along the interdiffusion path and, therefore, this is a demanding test for the proposed calculation method. The simulated concentration profiles are compared with results obtained by using two independent experimental techniques: Raman spectroscopy and dynamic mechanical analyzer (DMA). The total polystyrene (PS) concentration profiles, calculated using the proposed method, agree well with Raman spectroscopy results. Simulated DMA results—which are sensitive to the PS species molecular weight distribution—obtained using the concentration profiles, calculated for each PS molecular weight species agree well with the experimental DMA results. Calculations based on average molecular weights give incorrect results. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 3097–3107, 1999     

Fracture behavior–morphology relationships in an unsaturated polyester resin modified with a liquid oligomer

An unsaturated polyester (UP) resin modified with a liquid polymer, polyoxypropylenetriamine (POPTA), at a concentration of 10 wt% has been precured at several temperatures. Phase separation takes place before gelation at all precure temperatures used. The glass‐transition region has been analyzed by dynamic mechanical analysis. Mechanical properties have been related to microstructural features. With a precure temperature fixed, the unsaturated polyester (UP) resin has also been modified with different contents of POPTA. Fracture toughness of the mixtures has also been analyzed and results are compared to those for the unmodified mixture. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1677–1685, 1999     

Metalization of polymer beads via polymer‐supported hydrazines as reducing agents

A new method for depositing metal onto a polymer surface has been developed in which the metal coating of polymer beads is performed with hydrazine functions as reducing agents on the surface of the polymer itself. In this study, glycidyl methacrylate–methyl methacrylate–divinyl benzene terpolymer was prepared as spherical beads with a suspension polymerization methodology. Beads of the polymer sample (210–420‐μm fraction) containing 3.4 mmol g^?1 epoxy were treated with an excess of hydrazinium hydroxide to yield a polymer with 2.3 mmol g^?1 hydrazine functions. The hydrazine functions on the polymer surfaces were efficient in metal reductions. Therefore, the modified bead polymer samples, when soaked in aqueous ammonia solutions of Ni(II), Ag(I), and Cu(II) ions (0.1 M), were covered rapidly by the corresponding zero‐valent metal ions. Metal deposition took place almost quantitatively (ca. 4.5 mmol/g of the polymer) within 60 min of the contact times. The accumulations of metal were followed visually and occurred only on the polymer beads. There was no evidence that the reaction occurred within the solution. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 748–754, 2002; DOI 10.1002/pola.10158     

Liquid‐phase polymerization of propylene with a highly active Ziegler–Natta catalyst. Influence of hydrogen,cocatalyst, and electron donor on the reaction kinetics

This paper presents an experimental kinetic study of the polymerization of propylene in liquid monomer with a high activity catalyst. The influences of the concentration of hydrogen and the molar ratios of the catalyst, cocatalyst, and electron donor on the activation period, the maximum activity, the yield, and the decay behavior have been investigated at a temperature of 42°C using a relatively simple kinetic model. On the basis of the experimental data, the reaction rate has been modeled as a function of the hydrogen concentration, the molar ratio of cocatalyst and titanium, and the molar ratio of the electron donor and the cocatalyst. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 219–232, 1999     

The grafting of acrylamide onto poly(ε‐caprolactone) and poly(1,5‐dioxepan‐2‐one) using electron beam preirradiation. I. Influence of dose and Mohr's salt for the grafting onto poly(ε‐caprolactone)

Poly(ε‐caprolactone) films (TONE® 787) were irradiated by electron beam in air prior to grafting in aqueous solutions of acrylamide. The grafting kinetics and molecular weight of the grafted poly(acrylamide) chains were studied with irradiation doses between 2.5 and 20 Mrad and in the Mohr's salt concentration range of 0.0025–1 wt %. The grafting rate and yield were strongly dependent on the Mohr's salt concentration. By molecular weight analysis of grafted poly(acrylamide) chains, it was shown that the molecular weight is approximately proportional to the mass of the grafted PAAm. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1643–1649, 1999     

The inverse emulsion polymerization of acrylamide using polystyrene-graft-polyoxyethylene as the stabilizer

Inverse emulsion polymerization of aqueous solution of acrylamide (AM) in toluene is carried out using polystyrene-graft-polyoxyethylene (PSt-g-PEO) as an emulsifier. The kinetics of polymerization, morphology of the particle, and particle size of the inverse emulsion have been investigated. The rates of polymerization are found to be proportional to the initiator concentration, the monomer concentration, and the emulsifier concentration. The morphology of the particle shows a spherical structure. The effects of amphipathic graft copolymer structure on the average molecular weight of polyacrylamide are studied. The mechanism of the inverse emulsion polymerization using amphipathic graft copolymer as emulsifier is proposed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2719–2725, 1999     

Transport of benzene and methyl‐substituted benzenes through carbon black‐filled epoxidized natural rubber

Sorption and diffusion of benzene and methyl‐substituted benzenes were investigated through epoxidized natural rubber (ENR) reinforced with four types of carbon black: superabrasion furnace (SAF), intermediate superabrasion furnace (ISAF), high‐abrasion furnace (HAF), and semireinforcing furnace (SRF). Kraus equation has been used to investigate the extent of reinforcement for the different types of carbon black used in the experiments. Effect of the type and concentration of the carbon black on solvent uptake and mechanism of diffusion were studied in detail. The rate constant for diffusion of the solvents in epoxidized natural rubber vulcanizate based on different carbon black type, and loading was investigated. Diffusion constant was found to decrease with increase in the degree of reinforcement. The interaction constant values were experimentally determined. The sorption data were used to determine the activation energy for the diffusion process and the enthalpy and entropy of the sorption process. The experimental results were compared with theoretical predictions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 415–427, 1999     

New solvents for cellulose: Hydrazine/thiocyanate salt system

The hydrazine/thiocyanate system was found to be an excellent solvent for cellulose. The solubility and solution properties were investigated. Even at room temperature, the combinations of hydrazine and lithium, sodium, and potassium thiocyanate had high dissolution power for cellulose, up to an 18% (w/w) maximum, unrelated to the polymorph, whereas a combination with ammonium thiocyanate exhibited a solubility difference among celluloses I, II, and III. The effect of the temperature cycling of the system for the rapid dissolution of cellulose was investigated thermodynamically. In these systems, a high concentration of salts was necessary to effect the cellulose dissolution; this suggested that an undissociated salt–solvent complex played an important role in the cellulose dissolution as implied by electroconductivity measurements of the hydrazine/salt system. Gel and liquid‐crystal formation was observed in all systems above 4 and 6% (w/w) cellulose concentrations, respectively. The values of both critical concentrations were quite similar to those observed in the ammonia/ammonium thiocyanate system studied earlier in our laboratories. The gelation temperature was between approximately 10 and 50 °C, depending on the salt and cellulose concentration. The dependence of the cellulose solubility on the degree of polymerization was also examined. It is suggested that these solvent systems have great potential for the fiber and film formation of cellulose. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 601–611, 2002; DOI 10.1002/pola.10135     

Poly(propene-co-maleic acid) with lateral perester groups as initiator in the emulsion polymerization of styrene

The influence of the initiator structure on the reaction process was investigated. In addition to the initiator concentration, its molar mass and the content of perester groups in the single molecule are determining factors that influence the course of reaction. Quantitative relationships are shown. The initiator is bonded by grafting reactions on the surface of the latex particles. The grafted moiety is dependent on the initiator structure and reaction temperature. Latices with polydispersities lower than 1.1 are obtained. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2045–2054, 1999     

Diffusion of water–acetic acid mixtures in epoxy

The solubility and diffusion of water–acetic acid solutions in epoxy resins has been studied by nuclear magnetic resonance imaging (MRI) and spectroscopy (NMR), Fourier transform infrared (FTIR) spectroscopy, and light microscopy (LM). These techniques revealed the progression of a sharp diffusion front at a rate proportional to the square root of time. Both the swelling and rate of diffusion are dependent on acid dilution. At higher acid concentrations, hydrogen bonds were present, which has been interpreted as formation of acid dimers. The results indicate that molecular interactions play a major role in controlling the solubility and diffusion processes. The observation that voids can be filled up with penetrant strongly support the interpretation that molecular interactions rather than concentration gradient are responsible for these effects. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 3328–3336, 1999     

Cellulose dissolution in lithium chloride/N,N-dimethylacetamide solvent system: Relevance of kinetics of decrystallization to cellulose derivatization under homogeneous solution conditions

Rate constants and activation parameters for decrystallization of Avicel PH-101 cellulose, and bagasse-based cellulose in presence of LiCl/N,N-dimethylacetamide solvent system have been determined from dependence of the index of crystallinity of cellulose, Ic, on time, under nonisothermal conditions. Calculated rate constants and activation parameters are negligibly dependent on the degree of polymerization of the natural polymer. Under experimental conditions used, derivatization of cellulose can be started after 3 h of cellulose–solvent contact. The relevance of our results to the industrial application of derivatization under homogeneous solution conditions is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3738–3744, 1999     

Effects of solvent as an electron-pair acceptor on propagation reactions during radical polymerization and copolymerization of polar vinyl monomers

We carried out radical homopolymerization and copolymerization in various kinds of solvents at 60°C by using diisopropyl fumarate (DiPF) and methyl methacrylate (MMA) as electron-accepting polar monomers and styrene (St) and vinyl benzoate (VB) as electron-donating monomers. The highest polymerization rate was observed in the polar and electron-pair accepting solvents, such as 2,2,2-trifluoroethanol for the homopolymerization and copolymerization of these monomers. It has been revealed that the polymerization rate is correlated to the electron-pair–accepting property of the solvent used, rather than the polarity in the linear free energy relationship. We have demonstrated the validity of the acceptor number as the index for interpreting the interaction of the solvent with the monomer and the propagating chain end. The monomer reactivity ratios were determined for the St–DiPF, VB–DiPF, and St–MMA copolymerizations. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2803–2814, 1999     

Sorption and diffusion of low molecular weight gases and vapors in glassy polymers at high concentration of sorbate

A theoretical approach has been developed to describe the sorption and diffusion processes of low weight molecular gases and vapors in polymers at wide ranges of sorbate concentration. The equation of an S‐shaped gas sorption isotherm in glassy polymer matrix has been derived. The concentration dependence of the sorbate molecule diffusion coefficient has been established. For an S‐shaped sorption isotherm, this dependence is nonmonotonous. The conditions of cluster formation of sorbate molecules have been analyzed within the proposed approach, in which it is possible to determine a correlation between these conditions and parameters of sorption isotherm. The comparison of the experimental and theoretical data provides an assessment of the microscopic characteristics of investigated polymer–vapor systems, such as the distances between vapor molecules in a matrix corresponding to intermolecular repulsion and attraction. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2314–2323, 1999     

Diblock and triblock functional copolymers by controlled radical polymerization

Controlled polystyrenes with different molar mass values were synthesized starting from benzoyl peroxide and TEMPO (2,2,6,6‐tetramethylpiperidinyl‐1‐oxy). The polystyrene homopolymers served as initiators for the block copolymerization of phthalimide methylstyrene (PIMS) to synthesize polystyrene‐b‐poly(PIMS) diblock copolymers. Diblock copolymers with well defined structures as well as controlled and narrow molar mass distribution were obtained from the lower‐mass polystyrene homopolymers. The lower‐mass copolymers were found to be active as initiators in the synthesis of the polystyrene‐b‐poly(PIMS)‐b‐polystyrene triblock copolymers. In each reaction step, the effects of conversion and reaction time on the molar mass characteristics of the prepared block copolymers were investigated. The diblock and triblock copolymers were modified using hydrazine as the reagent in order to obtain the corresponding functional amino block copolymers. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1237–1244, 1999