Microstructure and mechanical properties of hot‐air drawn poly(ethylene terephthalate) fibers

Hot‐air drawing method has been applied to poly(ethylene terephthalate) (PET) fibers in order to investigate the effect of strain rate on their microstructure and mechanical properties and produce high‐performance PET fibers. The hot‐air drawing was carried out by blowing hot air controlled at a constant temperature against an as‐spun PET fiber connected to a weight. As the hot air blew against the fibers weighted variously at a flow rate of about 90 ℓ/min, the fibers elongated instantaneously at a strain rate in the range of 2.3–18.7 s⁻¹. The strain rate in the hot‐air drawing increased with increasing drawing temperature and applied tension. When the hot‐air drawing was carried out at a drawing temperature of 220°C under an applied tension of 27.6 MPa, the strain rate was the highest value of 18.7 s⁻¹. A draw ratio, birefringence, crystallite orientation factor, and mechanical properties increased as the strain rate increased. The fiber drawn at the highest stain rate had a birefringence of 0.231, degree of crystallinity of 44%, tensile modulus of 18 GPa, and dynamic storage modulus of 19 GPa at 25°C. The mechanical properties of fiber obtained had almost the same values as those of the zone‐annealed PET fiber reported previously. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1703–1713, 1999     

Application of zone-drawing and zone-annealing method to poly(p-phenylene sulfide) fibers

A zone-drawing and zone-annealing treatment was applied to poly(p-phenylene sulfide) fibers in order to improve their mechanical properties. The zone-drawing (ZD) was carried out at a drawing temperature of 90°C under an applied tension of 5.5 MPa, and the zone-annealing (ZA) was carried out at an annealing temperature of 220°C under 138.0 MPa. The differential scanning calorimetry (DSC) thermogram of the ZD fiber had a broad exothermic transition (T_c = 110°C) attributed to cold-crystallization and a melting endotherm peaking at 286°C. The T_c of the ZD fiber was lower than that (T_c = 128°C) of the undrawn fiber. In the temperature dependence of storage modulus (E′) for the ZD fiber, the E′ values decreased with increasing temperature, but increased slightly in the temperature range of 90–100°C, and decreased again. The slight increase in E′ was attributable to the additional increase in the crosslink density of the network, which was caused by strain-induced crystallization during measurement. The resulting ZA fiber had a draw ratio of 6.0, a degree of crystallinity of 38%, a tensile modulus of 8 GPa, and a tensile strength of 0.7 GPa. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1731–1738, 1998     

Drawing behavior and characteristics of laser‐drawn polypropylene fibers

Drawing behavior, flow drawing, and neck drawing, was studied for isotacticpolypropylene fibers in CO₂ laser drawing system, and the fiber structure and the mechanical properties of drawn fibers were analyzed. For a certain laser power, flow drawing of polypropylene (PP) was possible up to draw ratio (DR) 19.5. Though the drawing stress was very low, the flow‐drawn PP fiber exhibited oriented crystal structure and improved mechanical properties. On the other hand, neck‐drawing was accomplished from DR 4 to 12, with significant increase in drawing stress that enhanced the development of fiber structure and mechanical properties. Unlike PET, the drawing stress depends not only on the DR, but on irradiated laser power also. The 10–12 times neck‐drawn fibers were highly fibrillated. The fibers having tensile strength 910 MPa, initial modulus 11 GPa, and dynamic modulus 14 GPa were obtained by single‐step laser drawing system. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 398–408, 2006     

Effects of spinning conditions on the mechanical properties of ultrahigh‐molecular‐weight polyethylene fibers

We investigated the tensile strength and modulus of ultrahigh‐strength polyethylene (UHSPE) fibers obtained by using the special two‐step‐drawing process of as‐spun fiber (ASFs) which were prepared by the so‐called gel‐spinning method. We have found that the higher the ASF's spinning speed is, the higher the attainable tensile strength σ_f and modulus E are. For all the fibers drawn from ASFs with various spinning speed except for 120 m/min, we have found a master curve for the inverse of σ_f which is plotted as a function of T^1/4E^?1/2, where T is the linear density of the drawn fibers, in consistent with the Griffith theory: a thicker fiber obtained with a lower spinning speed exhibits lower strength, although all the AFSs possess the same value of E. This also suggests that a thicker fiber contains more defects which would lead to the Griffith‐type crack propagation breakage. Moreover, from morphological observation of ASFs under transmission electron microscopy, the ASF obtained at a relatively low spinning speed possesses a heterogeneous cross‐sectional morphology, whereas that obtained at relatively high spinning speed possesses a relatively homogenous morphology. We propose that this morphological evidence may account for the experimental findings of the behavior of the mechanical properties described above. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2639–2652, 2005     

High‐performance poly(ethylene‐2,6‐naphthalate) fiber prepared by high‐tension annealing

A high‐tension annealing (HTA) method has been applied to zone‐annealed poly(ethylene‐2,6‐naphthalate) (PEN) fibers in order to further improve their mechanical properties. The HTA treatment was carried out under an applied tension of 428 MPa at a treating temperature of 175 °C. The applied tension was close to the tensile strength at 175 °C. The resulting HTA fiber had a birefringence of 0.492 and degree of crystallinity of 57%. Wide‐angle X‐ray diffraction (WAXD) photographs of the HTA fibers showed three reflections (010, 100, and 1 10) attributed to an α form crystal, but no (020) reflection attributed to a β form was observed in the equator. The tensile modulus and tensile strength increased with processing, and the HTA fiber had a maximum modulus of 33 GPa, a tensile strength of 1.1 GPa, and a storage modulus of 33 GPa at 25 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 61–67, 2000     

Reactions of vinyl ethers with 2‐cyano‐2‐propyl and benzoyloxy radicals

tert‐Butyl, cyclohexyl, n‐propyl, and n‐dodecyl vinyl ethers have been used as comonomers with styrene and methyl methacrylate using ¹³C‐enriched samples of azobis(isobutyronitrile) and benzoyl peroxide as initiators at 60°C. Examination by ¹³C‐NMR spectroscopy of either (¹³CH₃)₂C(CN) or Ph¹³COO end‐groups in the products has shown that the vinyl ethers have low reactivities toward the 2‐cyano‐2‐propyl radical but high reactivities toward the benzoyloxy radical. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 771–777, 1999     

Preparation and physical properties of poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) films

To prepare thermally stable and high‐performance polymeric films, new solvent‐soluble aromatic polyamides with a carbamoyl pendant group, namely poly(4,4′‐diamino‐3′‐carbamoylbenzanilide terephthalamide) (p‐PDCBTA) and poly(4,4′‐diamino‐3′‐carbamoylbenzanilide isophthalamide) (m‐PDCBTA), were synthesized. The polymers were cyclized at around 200 to 350 °C to form quinazolone and benzoxazinone units along the polymer backbone. The decomposition onset temperatures of the cyclized m‐ and p‐PDCBTAs were 457 and 524 °C, respectively, lower than that of poly(p‐phenylene terephthalamide) (566 °C). For the p‐PDCBTA film drawn by 40% and heat‐treated, the tensile strength and Young's modulus were 421 MPa and 16.4 GPa, respectively. The film cyclized at 350 °C showed a storage modulus (E′) of 1 × 10¹¹ dyne/cm² (10 GPa) over the temperature range of room temperature to 400 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 775–780, 2000     

Morphological and mechanical properties of nascent polyethylene fibers produced via ethylene extrusion polymerization with a metallocene catalyst supported on MCM‐41 particles

Polyethylene (PE) fibers were prepared by ethylene extrusion polymerization with an MCM‐41‐supported titanocene catalyst. The morphological and mechanical properties of these nascent PE fibers were investigated. Three levels of fibrous morphologies were identified in the fiber samples through an extensive scanning electron microscopy study. Extended‐chain PE nanofibrils with diameters of about 60 nm were the major morphological units present in the fiber structure. The nanofibrils were parallel‐packed into individual microfibers with diameters of about 1–30 μm. The microfibers were further aggregated irregularly into fiber aggregates and bundles. In comparison with commercial PE fibers and data reported in the literature, the individual microfibers produced in situ via ethylene extrusion polymerization without posttreatment exhibited a high tensile strength (0.3–1.0 GPa), a low tensile modulus (3.0–7.0 GPa), and a high elongation at break (8.5–20%) at 35 °C. The defects in the alignment of the nanofibrils were believed to be the major reason for the low modulus values. It was also found that a slight tensile drawing could increase the microfiber strength and modulus. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2433–2443, 2003     

Measurement of size‐dependent glass transition temperature in electrospun polymer fibers using AFM nanomechanical testing

The glass transition temperature (T_g) of individual electrospun polymer polyvinyl alcohol fibers of varying diameter was measured using atomic force microscopy (AFM) based nanomechanical thermal analysis. Indentation and bending of individual electrospun fibers using AFM allowed the calculation of the elastic modulus of the polyvinyl alcohol (PVA) fibers across a range of different temperatures. The elastic modulus of electrospun PVA fibers was observed to decrease significantly when passing through T_g, which allowed accurate determination of T_g. The T_g of electrospun PVA fibers was shown to decrease for smaller fiber diameters especially for fiber diameters below 250 nm. This size‐dependent glass transition behavior of electrospun PVA fibers is indicated as being due to polymer chain confinement. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Enhanced electrical properties of highly oriented poly(vinylidene fluoride) films prepared by solid‐state coextrusion

Oriented poly(vinylidene fluoride) (PVDF) films with β‐form crystals have been commonly prepared by cold drawing of a melt‐quenched film consisting of α‐form crystals. In this study, we have successfully produced highly oriented PVDF thin films (20 µm thick) with β‐crystals and a high crystallinity (55–76%), by solid‐state coextrusion of a gel film to eight times the original length at an established optimum extrusion temperature of 160°C, some 10°C below the melting temperature. The resultant drawn films had a highly oriented (orientation function f_c = 0.993) fibrous structure, showing high mechanical properties of an extensional elastic modulus of 8.3 GPa and tensile strength of 0.84 GPa, along the draw direction. Such highly oriented and crystalline films exhibited excellent ferroelectric and piezoelectric properties. The square hysteresis loop was significantly sharper than that of a conventional sample. The sharp switching transient yielded the remnant polarization P_r of 90 mC/m², and the electromechanical coupling factor k_t was 0.24 at room temperature. These values are about 1.5 times greater than those of a conventional β‐PVDF film. Thus, solid‐state coextrusion near the melting point was found to be a useful technique for the preparation of highly oriented and highly crystalline β‐PVDF films with superior mechanical and electrical properties. The morphology of the extrudate relevant to such properties is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2549–2556, 1999     

Rigid‐rod polyamides and polyimides prepared from 4,3″‐diamino‐2′,6′‐di(2‐naphthyl)‐p‐terphenyl and 2′,6′,3‴,5‴‐tetra(2‐naphthyl)‐4,4″‐diamino‐p‐quinquephenyl

A series of rigid‐rod polyamides and polyimides containing p‐terphenyl or p‐quinquephenyl moieties in backbone as well as naphthyl pendent groups were synthesized from two new aromatic diamines. The polymers were characterized by inherent viscosity, elemental analysis, FT‐IR, ¹H‐NMR, ¹³C‐NMR, X‐ray, differential scanning calorimetry (DSC), thermomechanical analysis (TMA), thermal gravimetric analysis (TGA), isothermal gravimetric analysis, and moisture absorption. All polymers were amorphous and displayed T_g values at 304–337°C. Polyamides dissolved upon heating in polar aprotic solvents containing LiCl as well as CCl₃COOH, whereas polyimides were partially soluble in these solvents. No weight loss was observed up to 377–422°C in N₂ and 355–397°C in air. The anaerobic char yields were 57–69% at 800°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 15–24, 1999     

Synthesis and characterization of UV‐curable ladder‐like polysilsesquioxane

Various ladder‐like structured poly(phenyl‐co‐methacryl silsesquioxane)s (LPMSQ)s with high molecular weight (M_w = 10,000 ～ 40,000) were synthesized by direct hydrolysis and polymerization in the presence of base catalyst at 25 °C. Synthesized LPMSQs mainly showed ladder‐like structure and photo‐cure reaction by 100 mW/cm² (360 nm) for 10 s without any photo‐cure initiators. Chemical composition and structural analysis of the obtained LPMSQs were characterized using ¹H NMR, ²⁹Si NMR, Fourier transform infrared spectroscopy (FTIR), gel permeation chromatography (GPC), and X‐ray diffraction (XRD). Physical properties of LPMSQs before and after photcuring were analyzed by Nanoindentation. Surface modulus increased to 8GPa and hardness of thin films increased from 100 to 400 MPa. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Maximum tensile properties of oriented polyethylene,achieved by uniaxial drawing of solution‐grown crystal mats: Effects of molecular weight and molecular weight distribution

The effects of molecular weight (MW) and MW distribution on the maximum tensile properties of polyethylene (PE), achieved by the uniaxial drawing of solution‐grown crystal (SGC) mats, were studied. The linear‐PE samples used had wide ranges of weight‐average (M_w = 1.5–65 × 10⁵) and number‐average MWs (M_n = 2.0–100 × 10⁴), and MW distribution (M_w/M_n = 2.3–14). The SGC mats of these samples were drawn by a two‐stage draw technique, which consists of a first‐stage solid‐state coextrusion followed by a second‐stage tensile drawing, under controlled conditions. The optimum temperature for the second‐stage draw and the resulting maximum‐achieved total draw ratio (DR_t) increased with the MW. For a given PE, both the tensile modulus and strength increased steadily with the DR_t and reached constant values that are characteristic for the sample MW. The tensile modulus at a given DR_t was not significantly affected by the MW in the lower DR_t range (DR_t < 50). However, both the maximum achieved tensile modulus (80–225 GPa) and strength (1.0–5.6 GPa), as well as those at higher DR_ts > 50, were significantly higher for a higher MW. Although the maximum modulus reached 225 ± 5 for M_n ≥ 4 × 10⁵, the maximum strength continued to increase with M_n even for M_n > 4 × 10⁵, showing that strength is more strongly dependent on the M_n, even at higher M_n. Furthermore, it was found that each of the maximum tensile modulus and strength achieved could be expressed by a unique function of the M_n, independently of the wide variations of the sample MW and MW distribution. These results provide an experimental evidence that the M_n has a crucial effect on the tensile properties of extremely drawn and chain‐extended PE fibers, because the structural continuity along the fiber axis increases with the chain length, and hence with the M_n. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 153–161, 2006     

Superdrawing of polytetrafluoroethylene nascent powder by solid‐state coextrusion

A film of nascent powder of polytetrafluoroethylene (PTFE), compacted below the ambient melting temperature (T_m, 335 °C), was drawn by two‐stage draw techniques consisting of a first‐stage solid‐state coextrusion followed by a second‐stage solid‐state coextrusion or tensile draw. Although the ductility of extrudates was lost for the second‐stage tensile draw at temperatures above 150 °C due to the rapid decrease in strength, as previously reported, the ductility of extrudates increased with temperature even above 150 °C when the second‐stage draw was made by solid‐state coextrusion, reflecting the different deformation flow fields in a free space for the former and in an extrusion die for the latter. Thus, a powder film initially coextruded to a low extrusion draw ratio (EDR) of 6–20 at 325 °C was further drawn by coextrusion to EDRs up to ～?400 at 325–340 °C, near the T_m. Extremely high chain orientation (f_c = 0.998 ± 0.001), crystallinity (96.5 ± 0.5)%, and tensile modulus (115 ± 5 GPa at 24 °C, corresponding to 73% of the X‐ray crystal modulus) were achieved at high EDRs. Despite such a morphological perfection and a high modulus, the tensile strength of a superdrawn tape, 0.48 ± 0.03 GPa, was significantly low when compared with those (1.4–2.3 GPa) previously reported by tensile drawing above the T_m. Such a low strength of a superdrawn, high‐modulus PTFE tape was ascribed to the low intermolecular interaction of PTFE and the lack of intercrystalline links along the fiber axis, reflecting the initial chain‐extended morphology of the nascent powder combined with the fairly high chain mobility associated with the crystal/crystal transitions at around room temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3369–3377, 2006     

Syntheses and properties of organosoluble polyamides and polyimides based on the diamine 3,3‐bis[4‐(4‐aminophenoxy)‐3‐methylphenyl]phthalide derived from o‐cresolphthalein

Diamine 3,3‐bis[4‐(4‐aminophenoxy)‐3‐methylphenyl]phthalide (BAMP) was derived from the o‐cresolphthalein, and then it was polycondensated with various aromatic dicarboxylic acids and dianhydrides to synthesize polyamides (PAs) and polyimides (PIs), respectively. PAs have inherent viscosities of 0.78–2.24 dL/g. Most of the PAs are readily soluble in a variety of solvents such as DMF, DMAc, and NMP and afforded transparent and tough films from DMAc solutions. The cast films have tensile strengths of 75–113 MPa as well as initial moduli of 1.71–2.97 GPa. These PAs have glass transition temperatures (T_gs) in the range of 242–325°C, 10% weight loss temperatures occur up to 473°C, and char yields are between 57 and 64% at 800°C in nitrogen. PIs were first synthesized to form polyamic acids (PAAs) by a two‐stage procedure that included a ring‐opening reaction, followed by thermal or chemical conversion to polyimides. Inherent viscosities of PAAs are between 0.71 and 1.63 dL/g. Most of the PIs obtained through the chemical cyclodehydration procedure are soluble in NMP, o‐chlorophenol, m‐cresol, etc., and they have inherent viscosities of 0.58–1.32 dL/g. T_gs of these PIs are in the range of 270–305°C and show 10% weight loss temperatures up to 477°C. PIs obtained through the thermal cyclodehydration procedure have tensile strengths of 72–142 MPa, elongations at break of 8–19%, and initial moduli of 1.80–2.72 GPa. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 455–464, 1999     

Synthesis and properties of phosphorus containing polyester‐amides derived from 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl) phenylene

A series of polyester‐amides that contain phosphorus were synthesized by low temperature solution condensation of 1,4‐bis(3‐aminobenzoyloxy)‐2‐(6‐oxido‐6H‐dibenz〈c,e〉〈1,2〉oxaphosphorin‐6‐yl) phenylene (III) with various aromatic acid chlorides in N‐methyl pyrrolidone (NMP). All polyester‐amides are amorphous and readily soluble in many organic solvents such as dimethylacetamide (DMAc), NMP, dimethylsulfoxide, and dimethylformamide at room temperature or on heating. Light yellow and flexible films of these polyester‐amides could be cast from the DMAc solutions. The polymers with an inherent viscosity of 0.26–0.72 dL/g were obtained in quantitative yields. These polyester‐amides have good mechanical properties (G′ of ∼ 10⁹ Pa up to 200°C) and good thermal and flame retardant properties. The glass transition temperatures of these polyester‐amides ranged from 250 to 273°C. The degradation temperatures (T_d 5%) in nitrogen ranged from 466 to 478°C and the char yields at 800°C were 59.6–65.2%. The limiting oxygen indexes of these polyester‐amides ranged from 35 to 43. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 891–899, 1999     

Polymerization of o‐quinodimethanes. III. Polymerization of o‐quinodimethanes bearing electron‐withdrawing groups formed in situ by thermal ring‐opening isomerization of corresponding benzocyclobutenes

The substituent effect on the radical polymerization of o‐quinodimethanes, generated by thermal isomerization of benzocyclobutenes, was investigated. Polymerizations of three benzocyclobutenes bearing electron‐withdrawing groups were studied, namely 1‐cyanobenzocyclobutene (1), 1‐chlorobenzocyclobutene (2), and 1‐bromobenzocyclobutene (3). While radical polymerizations of 2 and 3 did not afford any polymer, radical polymerization of 1 afforded n‐hexane‐insoluble polymer(M_n = 5000) in moderate yields at temperatures above 120°C. The structure of the obtained polymer was confirmed to be a ring‐opened polymer(4) by IR, ¹H‐, and ¹³C‐NMR. The yield of the polymer increased with an increase in the initiator concentration. The polymer yield reported in this paper is higher than those of benzocyclobutenes bearing electron‐donating groups, reported previously by the authors. The semi‐empirical molecular orbital calculation supported the contribution of ring‐opening polymerization of spiro‐compounds, rejecting the possibility of 1,4‐polymerization. Lastly, radical copolymerizations of 1 with various comonomers were also performed to obtain the corresponding copolymers. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1555–1563, 1999     

Synthesis and properties of poly(1‐naphthylacetylene) and poly(9‐anthrylacetylene)

Polymerizations of 1‐naphthylacetylene (1‐NA) and 9‐anthrylacetylene (9‐AA) by various transition metal catalysts were studied, and properties of the polymers were clarified. 1‐NA polymerized with WCl₆‐based catalysts to offer dark purple polymers in good yield. Especially, a binary catalyst composed of WCl₆ and Ph₃Bi gave a polymer with high molecular weight (M_w = 140×10³) and sufficient solubility in common solvents. The use of Mo and Rh catalysts, in contrast, resulted in the formation of insoluble red poly(1‐NA)s. 9‐AA gave insoluble polymers by both WCl₆‐ and MoCl₅‐based catalysts in moderate to good yields. Copolymerization of 9‐AA with 1‐NA by WCl₆–Ph₃Bi provided a soluble copolymer which exhibited the largest third‐order nonlinear optical susceptibilities (χ⁽³⁾(−3ω; ω, ω, ω) = 40×10⁻¹²) among all the substituted polyacetylenes synthesized so far. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 277–282, 1999     

Melt drawing of ultra‐high molecular weight polyethylene: Comparison of Ziegler‐ and metallocene‐catalyzed reactor powders

The drawing behavior of the ultra‐high molecular weight polyethylene (UHMW‐PE) melts has been studied by comparing the stress/strain curves for two types of samples as polymerized using conventional Ziegler and newer metallocene catalyst systems. Two UHMW‐PE samples, having the same viscosity average molecular weight of 3.3 × 10⁶, but different molecular weight distribution, have been drawn from melt at special conditions. The sample films for drawing were prepared by compression molding of reactor powders at 180°C in the melt. Differences in the structural changes during drawing and resultant properties, ascribable to their broad or narrow molecular weight distribution, were estimated from tensile tests, SEM observations, X‐ray measurements and thermal analyses. The metallocene‐catalyzed sample having narrower molecular weight distribution, could be effectively drawn from the melt up to a maximum draw ratio (DR) of 20, significantly lower than that obtained for the Ziegler‐catalyzed sample, ∼ 50. The stress/strain curves on drawing were remarkably influenced by draw conditions, including draw temperature and rate. However, the most effective draw for both was achieved at 150°C and a strain rate of 5 min⁻¹, independent of sample molecular weight distribution. The efficiency of drawing, as evaluated by the resultant tensile properties as a function of DR, was higher for the metallocene‐catalyzed sample having narrower molecular weight distribution. Nevertheless, the maximum achieved tensile modulus and strength for the Ziegler sample, 50–55 and 0.90 GPa, respectively, were significantly higher than those for the metallocene sample, 20 and 0.65 GPa, respectively, reflecting the markedly higher drawability for the former than the latter. The stress/strain behavior indicated that the origin of differences during drawing from the melt could be attributed to the ease of chain relaxation for the lower molecular weight chains in the melt. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1921–1930, 1999     

Syntheses and properties of organosoluble polyimides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4, 7‐methanohexahydroindan

A series of organosoluble aromatic polyimides (PIs) was synthesized from 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐4,7‐methanohexahydroindan (3) and commercial available aromatic dianhydrides such as 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride (ODPA), 4,4′‐sulfonyl diphthalic anhydride (SDPA), or 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropanic dianhydride (6FDA). PIs (III_c–f), which were synthesized by direct polymerization in m‐cresol, had inherent viscosities of 0.83–1.05 dL/g. These polymers could easily be dissolved in N,N′‐dimethylacetamide (DMAc), N‐methyl‐2‐pyrrolidone (NMP), N,N‐dimethylformamide (DMF), pyridine, m‐cresol, and dichloromethane. Whereas copolymerization was proceeded with equivalent molar ratios of pyromellitic dianhydride (PMDA)/6FDA, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA)/6FDA, or BTDA/SDPA, or ½ for PMDA/SDPA, copolyimides (co‐PIs), derived from 3 and mixed dianhydrides, were soluble in NMP. All the soluble PIs could form transparent, flexible, and tough films, and they showed amorphous characteristics. These films had tensile strengths of 88–111 MPa, elongations at break of 5–10% and initial moduli of 2.01–2.67 GPa. The glass transition temperatures of these polymers were in the range of 252–311°C. Except for III_e, the 10% weight loss temperatures (T_d) of PIs were above 500°C, and the amount of carbonized residues of the PIs at 800°C in nitrogen atmosphere were above 50%. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1681–1691, 1999