Effect of the initial matrix material on the structure of radiation‐grafted ion‐exchange membranes: Wide‐angle and small‐angle X‐ray scattering studies

Seven different fluoropolymer films were used as matrix materials for radiation‐grafted ion‐exchange membranes. The crystallinity and preferred orientation of these membranes were studied with wide‐angle X‐ray scattering, and the lamellar structure of the membranes was examined with small‐angle X‐ray scattering. The crystallinity of poly(vinylidene fluoride) (PVDF)‐based matrix materials varied between 57 and 40%, and the crystallinity of the sulfonated samples varied between 34 and 23%. The lamellar periods of PVDF‐based matrix materials were about 115 Å, and the lamellar periods of poly(ethylene‐alt‐tetrafluoroethylene) and poly(tetrafluoroethylene‐co‐hexafluoropropylene) were 250 and 212 Å, respectively. When the samples were grafted, the lamellar periods increased. Correlation function analysis showed very clearly that the long‐range order decreased because of grafting and sulfonation processes. For those samples that showed good proton conductivity, the lamellar period also increased because of sulfonation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1539–1555, 2002     

Micro-Raman investigations of PVDF-based proton-conducting membranes

Proton-conducting membranes of poly(vinylidene fluoride), PVDF, grafted with styrene and thereafter sulfonated, were investigated by Raman spectroscopy. The depth and surface distribution of polystyrene grafts and crosslinker, as well as the sulfonation efficiency, were determined by using confocal micro-Raman spectroscopy. Highly grafted samples show homogeneous distribution of grafted material and homogeneous sulfonation. Depth profiles reveal uneven graft distribution for samples with low and intermediate degrees of grafting. In crosslinked samples, the crosslinker concentration in the interior of the film is found to be roughly 50% of the surface concentration. In contrast to what has previously been reported, the sulfonation efficiency is poor at low graft levels and is further inhibited by the presence of divinyl benzene, DVB, as crosslinker. At degrees of grafting above ∼ 60%, the crosslinker does not affect the sulfonation efficiency and a level of 70–90% sulfonation is reached. The matrix polymer structure is found to be largely retained after irradiation, grafting, and sulfonation. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3317–3327, 1999     

Chemically stable hybrid polymer electrolyte membranes prepared by radiation grafting,sulfonation, and silane‐crosslinking techniques

To prepare a crosslinked hybrid polymer electrolyte membrane (PEM) with high chemical stability, a silane monomer, namely p‐styryltrimethoxysilane (StSi), was first grafted to poly(ethylene‐co‐tetrafluoroethylene) (ETFE) film by γ‐ray preirradiation. Hydrolysis‐condensation and sulfonation were then performed on the StSi‐grafted ETFE (StSi‐g‐ETFE) films to give them crosslinks and proton conductibility, respectively. Thus, a crosslinked proton‐conducting hybrid PEM was obtained. The crosslinks introduced by the silane‐condensation have an inorganic ? Si? O? Si? structure, which enhance the chemical and thermal stabilities of the PEM. The effect of the timing of the hydrolysis‐condensation (before or after sulfonation) and the sulfonation method (by chlorosulfonic acid or H₂SO₄) on the properties of the resulting hybrid PEMs such as ion‐exchange capacity, proton conductivity, water uptake, chemical stability, and methanol permeability were investigated to confirm their applicability in fuel cells. We conclude that the properties of the new crosslinked hybrid StSi‐grafted PEMs are superior to divinylbenzene (DVB)‐crosslinked styrene‐grafted membranes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5559–5567, 2008     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Synthesis of proton‐conducting membranes by the utilization of preirradiation grafting and atom transfer radical polymerization techniques

The atom transfer radical polymerization (ATRP) of styrene onto poly(vinylidene fluoride)‐graft‐poly(vinylbenzyl chloride) (PVDF‐g‐PVBC) membranes was investigated. Novel membranes were designed for fuel‐cell applications. The benzyl chloride groups in the PVDF‐g‐PVBC membranes functioned as initiators, and a Cu‐based catalytic system with the general formula Cu(n)X_n/ligand [where X is Cl or Br and the ligand is 2,2′‐bipyridyl (bpy)] was employed for the ATRP. In addition, 10 vol % dimethylformamide was added for increased solubility of the catalyst complex in styrene. The system was homogeneous, except for the membrane, when the initiator/copper halide/ligand/monomer molar ratio was 1/1/3/500. As anticipated, the fastest polymerization rate of styrene was observed with the copper bromide/bpy‐based catalyst system. The reaction rate was strongly temperature‐dependent within the studied temperature interval of 100–130 °C. The degree of grafting increased linearly with time, thereby indicating first‐order kinetics, regardless of the polymerization temperature. Furthermore, 120 °C was the maximum polymerization temperature that could be used in practice because the membrane structure was destroyed at higher temperatures. The degree of styrene grafting reached 400% after 3 h at 120 °C. Such a high degree of grafting could not be reached with conventional uncontrolled radiation‐induced grafting methods because of termination reactions. On the basis of an Arrhenius plot, the activation energy for the homogeneous ATRP of styrene was 217 kJ/mol. The prepared membranes became proton‐conducting after sulfonation of the polystyrene grafts. The highest conductivity measured for the prepared membranes was 70 mS/cm, which is comparable to the values normally measured for commercial Nafion membranes. The scanning electron microscopy/energy‐dispersive X‐ray results showed that the membranes had to be grafted through the matrix with both PVBC and polystyrene to become proton‐conducting after sulfonation. In addition, PVDF‐g‐[PVBC‐g‐(styrene‐block‐tert‐butyl acrylate)] membranes were also synthesized by ATRP. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 591–600, 2002; DOI 10.1002/pola.10146     

ASAXS study of styrene‐grafted sulfonated poly(vinylidene fluoride) membranes

Small‐angle and wide‐angle X‐ray scattering and anomalous small‐angle X‐ray scattering were used to investigate proton‐conducting membranes prepared by radiation‐induced styrene grafting and sulfonation of commercial poly(vinylidene fluoride) (PVDF‐g‐PS) films. The membranes retain the lamellar and highly oriented structure of the original PVDF films even through excessive grafting and sulfonation. The sulfonate groups aggregate in the central part of the amorphous layers, where they form a weakly ordered structure that does not show any preferred orientation. This structure is suggested to be lamellar with alternate metal‐sulfonated hydrate and PVDF‐g‐PS layers. The lamellar period is 15.1 Å. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1734–1748, 2000     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Synthesis and properties of sulfonated and crosslinked poly[(vinylidene fluoride)-graft-styrene] membranes

Crosslinked proton exchange membranes were prepared by electron beam grafting of styrene with divinylbenzene, DVB, or bis(vinyl phenyl)ethane, BVPE, on to poly(vinylidene fluoride), PVDF, followed by sulfonation. The area and thickness increase, crystallinity and mechanical properties of the membranes were investigated. All these properties were influenced by the crosslinker structure and its concentration. The crosslinkers increase the final degree of grafting. For noncrosslinked membranes it was about 80% and with 10% of BVPE crosslinker about 180% after 8 hr. The area increase with grafting is very similar for the noncrosslinked membranes and the differently crosslinked membranes, but the crosslinkers reduce swelling for sulfonated membranes swelled in boiling water. DVB reduces swelling more than BVPE. With grafting, the crystallinity of the PVDF phase decreases; with 10% BVPE the decrease is smallest and with 10% DVB largest. The mechanical properties of the sulfonated swelled membranes decrease with the degree of grafting, for a 10% DVB crosslinked membrane the strength decreases to zero at degrees of grafting higher than 75%. © 1998 John Wiley & Sons, Ltd.     

Radiation grafted poly(vinylidene fluoride)-graft-polystyrene sulfonic acid membranes for fuel cells: Structure-property relationships

<正>Structure-property relationships for poly(vinylidene fluoride)-graft-polystyrene sulfonic acid(PVDF-g-PSSA) fuel cell membranes prepared by a single step method involving radiation-induced grafting of sodium styrene sulfonate(SSS) onto electron beam(EB) irradiated poly(vinylidene fluoride)(PVDF) films were established.The physico-chemical properties of the membranes such as ion exchange capacity,water swelling and proton conductivity were correlated with the degree of grafting(G,%) and the structural changes taking place in the membrane matrix during the preparation procedure. The variation in the crystallinity and the thermal stability of membranes was studied by differential scanning calorimetry (DSC) and thermogravimetric analysis(TGA),respectively.The membranes were found to undergo substantial structural changes in forms of ionic sites increase,hydrophilicity enhancement,hydrophobicity reduction and crystallinity decrease with the variation in G(%) and the preparation method.The structural and thermal properties of the obtained membranes were also compared with their counterparts prepared by a conventional two-steps method i.e.radiation induced grafting of styrene onto EB irradiated PVDF films followed by sulfonation.The PVDF-g-PSSA membranes obtained by a single-step method were found to have superior properties compared to those obtained by the conventional two-steps method.     

PVDF/PMMA brushes membrane for lithium‐ion rechargeable batteries prepared via preirradiation grafting technique

Poly(methyl methacrylate) (PMMA) was anchored to multiporous poly(vinylidine fluoride) (PVDF) surface via electron beam preirradiation grafting technique to prepare PVDF/PMMA brushes. The conformation of the PVDF/PMMA brushes was verified through Attenuated total reflection‐Fourier transform infra red spectroscopy (ATR‐FTIR), energy dispersive X‐ray spectroscopy (EDX), and scanning electron microscopy (SEM). Thermal stability of PVDF/PMMA brushes was characterized by thermo gravimetric analysis (TGA). The degradation of PVDF/PMMA brushes showed a two‐step pattern. PVDF/PMMA brushes membrane could be used as polymer electrolyte in lithium‐ion rechargeable batteries after it was activated by uptaking 1 M LiPF₆/EC‐DMC (ethylene carbonate/dimethyl carbonate; EC:DMC = 1:1 by volume) electrolyte solution. The activated membrane showed high ionic conductivity, 6.1 × 10^?3 S cm^?1 at room temperature, and a good electrochemical stability up to 5.0 V. The excellent performances of multiporous PVDF‐g‐PMMA membranes suggest that they are suitable for application in high‐performance lithium‐ion batteries. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 751–758, 2008     

Multi‐functional poly(vinylidene fluoride) graft copolymers

Poly(vinylidene fluoride) (PVDF) is known for its biocompatibility, piezo and pyro‐electricity, and membrane forming capability. In order to tune its properties, modification through grafting from approach by atom transfer radical polymerization (ATRP) is preferred. Hydrophilic polymers like poly(ethylene glycol) methacrylate, poly(methacrylic acid), poly(dimethylaminoethyl methacrylate) (PDMAEMA), and so forth have been anchored from PVDF backbone in order to make permeation of water molecules through the PVDF based membranes. The successful solution grafting of PDMAEMA chains from PVDF backbone by ATRP resulted appreciable graft conversion and hence its bulk properties showed a significant change. This water soluble graft copolymer shows incredible mechanical and adhesive properties. PVDF‐g‐poly(n‐butyl methacrylate) generates honey‐comb porous film using “breath figure” technique. Recently, they have used further improvement of grafting where model ATRP initiators are anchored using atom transfer radical coupling and used them as macroinitiators for grafting. This approach simplified the grafting reactions even more and enabled successful grafting of a large number of monomers under relatively less drastic conditions with appreciable conversion compared with the previous conditions. This technique has resulted interesting solution properties, ion and electron conducting PVDF, antifouling membrane, super glue and super tough materials, capable of generating metal nanoparticles tunable with pH and temperature. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2569–2584     

Preparation of poly(ether ether ketone)-based polymer electrolytes for fuel cell membranes using grafting technique

Poly(ether ether ketone) (PEEK)-based polymer electrolyte membranes (PEMs) was successfully prepared by radiation grafting of a styrene monomer into PEEK films and the consequent selective sulfonation of the grafting chains in the film state. Using milder sulfonation, the sulfonation reactions proceeded at the grafted chains in preference to the phenylene rings of PEEK main chains; as a result, the grafted films could successfully transform to a PEM with conductivity of more than 0.1 S/cm. The ion exchange capacity (IEC) and conductivity of the grafted PEEK electrolyte membranes were controlled to the ranges of 1.2–2.9 mmol/g and 0.03–0.18 S/cm by changing the grafting degree. It should be noted that this is the first example of directly transforming super-engineering plastic films into a PEM using radiation grafting.     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

Atom transfer radical polymerization directly from poly(vinylidene fluoride): Surface and antifouling properties

The direct preparation of grafting polymer brushes from commercial poly (vinylidene fluoride) (PVDF) films with surface‐initiated atom transfer radical polymerization (ATRP) is demonstrated. The direct initiation of the secondary fluorinated site of PVDF facilitated grafting of the hydrophilic monomers from the PVDF surface. Homopolymer brushes of 2‐(N,N‐dimethylamino)ethyl methacrylate (DMAEMA) and poly (ethylene glycol) monomethacrylate (PEGMA) were prepared by ATRP from the PVDF surface. The chemical composition and surface topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy, attenuated total reflectance/Fourier transform infrared spectroscopy, and atomic force microscopy. A kinetic study revealed a linear increase in the graft concentration of poly[2‐(N,N‐dimethylamino)ethyl methacrylate] (PDMAEMA) and poly[poly(ethylene glycol) monomethacrylate] (PPEGMA) with the reaction time, indicating that the chain growth from the surface was consistent with a controlled or living process. The living chain ends were used as macroinitiators for the synthesis of diblock copolymer brushes. The water contact angles on PVDF films were reduced by the surface grafting of DMAEMA and PEGMA. Protein adsorption experiments revealed a substantial antifouling property of PPEGMA‐grafted PVDF films and PDMAEMA‐grafted PVDF films in comparison with the pristine PVDF surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3434–3443, 2006     

The grafting of acrylamide onto poly(ε‐caprolactone) and poly(1,5‐dioxepan‐2‐one) using electron beam preirradiation. I. Influence of dose and Mohr's salt for the grafting onto poly(ε‐caprolactone)

Poly(ε‐caprolactone) films (TONE® 787) were irradiated by electron beam in air prior to grafting in aqueous solutions of acrylamide. The grafting kinetics and molecular weight of the grafted poly(acrylamide) chains were studied with irradiation doses between 2.5 and 20 Mrad and in the Mohr's salt concentration range of 0.0025–1 wt %. The grafting rate and yield were strongly dependent on the Mohr's salt concentration. By molecular weight analysis of grafted poly(acrylamide) chains, it was shown that the molecular weight is approximately proportional to the mass of the grafted PAAm. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1643–1649, 1999     

Viscoelastic phase diagram of fluorinated and grafted polymer films and proton‐exchange membranes for fuel cell applications

The influence of temperature and moisture activity on the viscoelastic behavior of fluorinated membranes for fuel cell applications was investigated. Uncrosslinked and crosslinked ethylene tetrafluoroethylene (ETFE)‐based proton‐conducting membranes were prepared by radiation grafting and subsequent sulfonation and their behavior was compared with ETFE base film and commercial Nafion^® NR212 membrane. Uniaxial tensile tests and stress relaxation tests at controlled temperature and relative humidity (RH) were carried out at 30 and 50 °C for 10% < RH < 90%. Grafted films were stiffer and exhibited stronger strain hardening when compared with ETFE. Similarly, both uncrosslinked and crosslinked membranes were stiffer and stronger than Nafion^®. Yield stress was found to decrease and moisture sensitivity to increase on sulfonation. The viscoelastic relaxation of the grafted films was found to obey a power‐law behavior with exponent equal to ?0.04 ± 0.01, a factor of almost 2 lower than ETFE, weakly influenced by moisture and temperature. Moreover, the grafted films presented a higher hygrothermal stability when compared with their membranes counterparts. In the case of membranes, a power‐law behavior at RH < 60% was also observed. However, a markedly different behavior was evident at RH > 60%, with an almost single relaxation time exponential. An exponential decrease of relaxation time with RH from 60 s to 10 s was obtained at RH ≥ 70% and 30 °C. The general behavior of grafted films observed at 30 °C was also obtained at 50 °C. However, an anomalous result was noticed for the membranes, with a higher modulus at 50 °C when compared with 30 °C. This behavior was explained by solvation of the sulfonic acid groups by water absorption creating hydrogen bonding within the clusters. A viscoelastic phase diagram was elaborated to map critical conditions (temperature and RH) for transitions in time‐dependent behavior, from power‐law scaling to exponential scaling. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1139–1148     

Synthesis and characterization of grafted/crosslinked proton conducting membranes based on amphiphilic PVDF copolymer

A novel graft copolymer consisting of a poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(glycidyl methacrylate) side chains, that is, P(VDF‐co‐CTFE)‐g‐PGMA, was synthesized through atom transfer radical polymerization (ATRP) using CTFE units as a macroinitiator. Successful synthesis and microphase‐separated structure of the polymer were confirmed by ¹H NMR, FTIR spectroscopy, and TEM. As‐synthesized P(VDF‐co‐CTFE)‐g‐PGMA copolymer was sulfonated by sodium bisulfite, followed by thermal crosslinking with sulfosuccinic acid (SA) via the esterification to produce grafted/crosslinked polymer electrolyte membranes. The IEC values continuously increased with increasing SA content but water uptake increased with SA content up to 10 wt %, above which it decreased again as a result of competitive effect between crosslinking and hydrophilicity of membranes. At 20 wt % of SA content, the proton conductivity reached 0.057 and 0.11 S/cm at 20 and 80 °C, respectively. The grafted/crosslinked P(VDF‐co‐CTFE)‐g‐PGMA/SA membranes exhibited good mechanical properties (>400 MPa of Young's modulus) and high thermal stability (up to 300 °C), as determined by a universal testing machine (UTM) and TGA, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1110–1117, 2010     

Facile synthesis of amphoteric ion exchange membrane by radiation grafting of sodium styrene sulfonate and N,N‐dimethylaminoethyl methacrylate for vanadium redox flow battery

Sodium styrene sulfonate (SSS) and N,N‐dimethylaminoethyl methacrylate (DMAEMA) are grafted into poly(vinylidene difluoride) (PVDF) film using γ‐radiation techniques. SSS could be co‐grafted successfully with DMAEMA, although it is difficult to be grafted solely into PVDF films. Through subsequent protonation process, an amphoteric ion exchange membrane (AIEM) is synthesized facilely and environmentally benignly. The degree of grafting (DOG) increases with absorbed dose and levels off at 40 kGy. Micro‐FTIR and X‐ray photoelectron spectroscopy analyses confirm the existence of the designed units and quaternization of DMAEMA units in the grafted films. The quaternization and grafting occurring at the same time makes it a unique way to synthesize quaternized AIEM in one step. Finally, an AIEM with a DOG of 43% is assembled in the vanadium redox flow battery (VRFB) system, and the VRFB maintains an open circuit voltage higher than 1.4 V after placed for 85 h, which is much longer than that with Nafion117 membrane. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5194–5202     

Radiation grafting of styrene onto poly(vinylidene fluoride) films in propanol: The influence of solvent and synthesis conditions

Electron‐beam‐irradiated poly(vinylidene fluoride) films were grafted with styrene with propanol or toluene as a solvent. The influence of the synthesis conditions and, more particularly, of the solvent was investigated. In propanol, the order of dependence of the grafting rate is 0.43 on the pre‐irradiation dose and 1.2 on the monomer concentration. The activation energy of the grafting reaction in propanol is approximately 73 kJ/mol. Both the initial grafting rate and the saturation degree of grafting are considerably higher in propanol, which is unable to swell polystyrene grafts, than in toluene, which diffuses with styrene through the grafted moiety. The grafting solvent also influences the structure of the membrane: films grafted in propanol have a much reduced elongation at break and a rougher surface. It is suggested that phase‐separated polystyrene domains may be larger when grafting is carried out in a styrene–propanol solution. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1512–1519, 2000