Organosoluble optically transparent poly(amide-imide)s based on 2,2-bis [<Emphasis Type="Italic">N</Emphasis>-(3-carboxyphenyl)phthalimidyl]- hexafluoropropane and 2,2-bis [<Emphasis Type="Italic">N</Emphasis>-(4-carboxyphenyl)phthalimidyl]- hexafluoropropane and various aromatic diamines

 Two diimide-dicarboxylic acids, 2,2-bis[N-(4-carboxyphenyl)phthalimidyl]hexafluoropropane (p-I) and 2,2,-bis[N-(3-carboxyphenyl)phthalimidyl]hexafluoropropane (m-I), were prepared by azeotropic condensation of 4,4′-(hexafluoroisopropylidene)diphthalic anhydride and p-aminobenzoic acid or m-aminobenzoic acid at a 1:2 molar ratio in N,N-dimethylacetamide/toluene. Two series of organosoluble and colorless poly(amide–imide)s were synthesized from diimide–diacid p-I or m-I with ten kinds of aromatic diamines by direct polycondensation using triphenyl phosphite and pyridine as condensing agents. The thin films cast from N,N-dimethylacetamide were measured by UV–vis spectroscopy and Macbeth color-eye colorimetery, the cutoff wavelengths of almost all the films were below 400 nm (361–389 nm) and the values of the parameter b* were between 15.31 and 34.72; these polymers are much lighter in color than other analogous polymers. Almost all the polymer were soluble in N-methyl-2-pyrrolodone, N,N-dimethylacetamide, N,N-dimethylformamide and dimethyl sulfoxide, and some polymers could dissolve in less polar solvents, such as dioxane and tetrahydrofuran, etc. The cast films exhibited yield strengths of 95–131 MPa, tensile strengths ranging from 92 to 130 MPa, elongations at break from 9 to 27%, and initial moduli from 2.1 to 3.3 GPa. The poly(amide–imide)s had glass-transition temperatures between 259 and 328°C and 10%-weight-loss temperatures above 510 °C in nitrogen and air, indicating excellent thermal stability. Received: 25 April 2001 Accepted: 27 June 2001     

New poly(amide-imide) syntheses. V. Preparation and properties of poly(amide-imide)s based on the diimide—diacid condensed from 2,2-bis[4-(4-aminophenoxy)phenyl]propane and trimellitic anhydride

A dicarboxylic acid ( 1 ) bearing two pre-formed imide rings, was prepared from the condensation of 2,2-bis[4-(4-aminophenoxy)phenyl]propane and trimellitic anhydride. A new family of poly(amide-imide)s having inherent viscosities of 0.53–1.68 dL/g was prepared by the triphenyl phosphite activated polycondensation from the diimide—diacid I with various aromatic diamines in a medium consisting of N-methyl-2-pyrolidone (NMP), pyridine, and calcium chloride. Most of the resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these poly(amide-imide)s were in the range of 237–293°C and the 10% weight loss temperatures were above 508°C in nitrogen. © 1993 John Wiley & Sons, Inc.     

New poly (amide-imide) syntheses. IX. Preparation and properties of poly(amide-imide)s derived from 2,7-bis (4-aminophenoxy) naphthalene and various bis (trimellitimide)s

Eleven bis(phenoxy) naphthalene-containing poly(amide-imide)s IIIa–k were synthesized by the direct polycondensation of 2,7-bis (4-aminophenoxy) naphthalene (DAPON) with various aromatic bis (trimellitimide)s IIa–k in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly (amide-imide)s IIIa–k having inherent viscosities of 0.70–1.12 dL/g were obtained in quantitative yields. The polymers containing p-phenylene or bis(phenoxy) benzene units exhibited crystalline x-ray diffraction patterns. Most of the polymers were readily soluble in various solvents such as NMP, N, N-dimethylacetamide, dimethyl sulfoxide, m-cresol, o-chlorophenol, and pyridine, and gave transparent, and flexible films cast from DMAc solutions. Cast films showed obvious yield points in the stress-strain curves and had strength at break up to 87 MPa, elongation to break up to 11%, and initial modulus up to 2.10 GPa. These poly(amide-imide)s had glass transition temperatures in the range of 255–321°C, and the 10% weight loss temperatures were recorded in the range of 529–586°C in nitrogen. The properties of poly(amideimide)s IIIa–k were compared with those of the corresponding isomeric poly (amide-imide)s III′ prepared from 2,7-bis(4-trimellitimidophenoxy) naphthalene and aromatic diamines. © 1994 John Wiley & Sons, Inc.     

Preparation and characterization of colorless alternate poly(amide-imide)s based on trimellitic anhydride and 2,2-bis[4-(3-aminophenoxy)phenyl]sulfone

Alternate poly(amide-imide) [P(A-alt-I)] was synthesized from two aromatic diamines and trimellitic anhydride (TMA). When the diamine was 2,2-bis[4-(3-aminophenoxy)phenyl]sulfone (BAPS), the resulted P(A-alt-I) was found to be of light color. Specifically, when BAPS was located between two amide groups in the P(A-alt-I) chain, the P(A-alt-I) was almost colorless. A series of P(A-alt-I)s (Series III) containing BAPS was synthesized through direct polycondensation of an aromatic dicarboxylic acid prepared from various aromatic diamines and TMA, as well as BAPS. Polymers of Series III were much lighter in color than those of the isomeric series (BAPS was located between two imide group). The series of P(A-alt-I)s III had inherent viscosities ranging 0.69–1.35 dL/g and good solubility in various solvents. The tensile strengths, elongations to break, and initial moduli of the films were 72–107 MPa, 7–12% and 1.93–2.39 GPa, respectively, and most of the films had no yielding. Polymers of Series III had glass transition temperatures 210–272°C and 10% weight loss temperatures in nitrogen 518–545°C, indicating excellent thermal stability. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2421–2428, 1999     

New poly(amide-imide)s syntheses. VII. Preparation and properties of poly(amide-imide)s derived from 1,5-bis(4-aminophenoxy) naphthalene,trimellitic anhydride,and various aromatic diamines

New bis(phenoxy)naphthalene-containing poly(amide-imide)s having an inherent viscosity in the range of 0.62–1.09 dL/g were prepared by the direct polycondensation of 1,5-bis(4-trimellitimidophenoxy) naphthalene ( I ) and various aromatic diamines using triphenyl phosphite and pyridine as condensing agents in N-methyl-2-pyrrolidone (NMP) in the presence of calcium chloride. The diimide-diacid (I) was prepared by the condensation of 1,5-bis(4-aminophenoxy) naphthalene and trimellitic anhydride. Most of the polymers were soluble in aprotic solvents such as NMP and N,N-dimethylacetamide (DMAc), and afforded transparent, flexible and tough films upon casting from DMAc solutions. Measurements of wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or oxyphenylene groups were characterized as crystalline polymers. Tensile strength and initial moduli of the polymer films ranged from 61–86 MPa and 1.83–2.21 GPa, respectively. Glass transition temperatures of the polymers were in the range of 231–340°C. The melting points of the crystalline polymers ranged from 375–430°C. The 10% weight loss temperatures were above 512°C in nitrogen and 481°C in air. © 1993 John Wiley & Sons, Inc.     

New poly(amide-imide)s syntheses. VIII. Preparation and properties of poly (amide-imide)s derived from 2,3-bis(4-aminophenoxy)naphthalene,trimellitic anhydride,and various aromatic diamines

The new polymer-forming diimide-diacid, 2,3-bis(4-trimellitimidophenoxy) naphthalene (I), was readily obtained by the condensation reaction of 2,3-bis (4-aminophenoxy) naphthalene with trimellitic anhydride. A series of novel aromatic poly (amide-imide)s were prepared by the direct polycondensation of diimide-diacid I with various aromatic diamines using triphenyl phosphite in N-methyl-2-pyrrolidone (NMP)/pyridine solution containing dissolved calcium chloride. The resultant polymers have inherent viscosities in the range of 0.65–1.02 dL/g at 30°C in N, N-dimethylacetamide. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed tensile strength at break up to 86 MPa, elongation to break of 5–9%, and initial moduli up to 2.35 GPa. The wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or p-oxyphenylene group are partially crystalline, and the other polymers are evidenced as amorphous patterns. These polymers show a glass transition in the range of 213–290°C in their differential scanning calorimetry (DSC) traces. The thermal stability of the polymers was evaluated by thermogravimetry analysis, which showed the 10% weight-loss temperatures in the range of 508–565°C in nitrogen and 480–529°C in air atmosphere. © 1994 John Wiley & Sons, Inc.     

Synthesis and properties of novel poly(amide-imide)s containing pendent diphenylamino groups

A new dicarboxylic acid, 2,4-bis(N-trimellitoyl)triphenylamine, bearing two preformed imide rings was synthesized from the condensation of 2,4-diaminotriphenylamine and trimellitic anhydride at 1:2 molar ratio. A series of poly(amide-imide)s (PAIs) with inherent viscosities of 0.38-0.66 dl/g were prepared by triphenyl phosphite-activated polycondensation from the diimide-dicarboxylic acid with various aromatic diamines. All the resulting PAIs were readily soluble in a variety of organic solvents and formed strong and tough films via solution casting. These PAIs have useful levels of thermal stability associated with moderately high glass-transition temperatures (259-314 °C) and 10% weight loss temperatures in excess of 530 °C in nitrogen or in air.     

New poly(amide-lmide)s syntheses. XV. Preparation and properties of poly(amide-imide)s derived from 9, 9-bis[4-(4-aminophenoxy) phenyl]fluorene and various bis(trimellitimide)s

Fifteen bis(phenoxy) fluorene-containing poly(amide-imide)s III were synthesized by the direct polycondensation of 9,9-bis[4-(4-aminophenoxy)phenyl]fluorene (BAPPF) with var-ious aromatic bis(trimellitimide)s II in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly(amide-imide)s III having inherent vis-cosities up to 1.45 dL/g were obtained in quantitative yields. Most of the resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 263–315°C and the 10% weight loss temperatures were above 510°C in nitrogen. Some properties of poly(amide-imide)s III were compared with those of the corresponding isomeric poly(amide-imide)s III ′ prepared from 9,9-[4-(4-trimellitimidophenoxy)phenyl]fluorene and various aromatic diamines. © 1995 John Wiley & Sons, Inc.     

New poly(amide-imide)s syntheses. XVII. Preparation and properties of poly(amide-imide)s derived from 3,3-Bis[4-(4-aminophenoxy)phenyl]phthalimidine and various bis(trimellitimide)s

A series of novel bis(phenoxy)phthalimidine-containing poly(amide-imide)s III were synthesized by the direct polycondensation of 3,3-bis[4-(4-aminophenoxy)phenyl]phthalimidine (BAPP) with various aromatic bis(trimellitimide)s in N-methyl-2-pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. Poly(amide-imide)s III , having inherent viscosities up to 1.36 dL/g, were obtained in quantitative yields. All resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 267–322°C and the 10% weight loss temperatures were above 490°C in nitrogen. Some properties of poly(amide-imide)s III were compared with those of the corresponding isomeric poly(amide-imide)s III′ prepared from 3,3-[4-(4-trimellitimidophenoxy)phenyl]-phthalimidine and various aromatic diamines. © 1996 John Wiley & Sons, Inc.     

New poly(amide-imide) syntheses. XII. Preparation and properties of poly(amide-imide)s based on the diimide-diacid condensed from 9,9-bis[4-(4-aminophenoxy)phenyl] fluorene and trimellitic anhydride

A dicarboxylic acid ( I ) was prepared from the condensation of 9,9-bis[4-(4-aminophenoxy) phenyl] fluorene and trimellitic anhydride. A new family of poly(amide-imide)s having inherent viscosities of 0.75-1.04 dL/g was prepared by the triphenyl phosphite activated polycondensation from the diimide-diacid I with various aromatic diamines in a medium consisting of N-methyl-2-pyrrolidone (NMP), pyridine, and calcium chloride. Most of the resulting polymers showed an amorphous nature and were readily soluble in polar solvents such as NMP and N,N-dimethylacetamide. All the soluble poly(amide-imide)s afforded transparent, flexible, and tough films. The glass transition temperatures of these polymers were in the range of 262–325°C and the 10% weight loss temperatures were above 525°C in air. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of new AB-type poly(etherimide)s containing bisphenol moieties

A series of new AB-type poly(etherimide)s having bisphenol-type moiety was prepared by the one-pot polyimidization using triphenylphosphite(TPP) in N-methyl-2-pyrrolidone(NMP)/pyridine solution at 150°C. Complete cyclodehydration was observed in the polymerizations as well as in model reactions. Polymers were obtained with inherent viscosities in the 0.27–0.49 dL/g range. The M_n and M_w/M_n of poly[4-(1,4-phenyleneoxy-1,4-phenylenehexafluoro-isopropylidene-1,4-phenylene)oxyphthalimide] (4d) with η_inh = 0.49 dL/g were 73,400 g/mol and 1.5, respectively. Most polymers could readily be dissolved in common organic solvents such as DMAc, NMP, and m-cresol. The polymer 4d was soluble even in chloroform. These polymers had glass transition temperatures between 205 and 235°C, and 5% weight loss temperatures in the range of 511–532°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3530–3536, 1999     

Microwave-assisted rapid synthesis of novel optically active poly(amide-imide)s containing hydantoins and thiohydantoins in main chain

Rapid and highly efficient synthesis of novel optically active poly(amide-imide)s (PAIs) 6(a-f) was achieved using microwave irradiation. These were made from the polycondensation reactions of 4,4^′-carbonyl-bis(phthaloyl-l-alanine) diacid chloride [N,N^′-(4,4^′-carbonyldiphthaloyl)] bisalanine diacid chloride 5 with six different derivatives of hydantoin and thiohydantoin compounds 4(a-f) in the presence of a small amount of a nonpolar organic medium that acts as a primary microwave absorber. Hydantoin and thiohydantoin derivatives 4(a-e) were synthesis from the reactions between benzil or benzil derivatives 3(a-e) with urea and thiourea. 5,5-Dimethylhydantoin 4f was synthesis from the reactions between acetone cyanohydrin 3f and ammonium carbonate. The polycondensation proceeded rapidly, and was completed within 10 min giving a series of PAIs with an inherent viscosity about 0.25-0.45 dL/g. The resulting PAIs 6(a-f) were obtained in a high yield and were optically active and thermally stable. All of the above compounds were fully characterized by means of Fourier transform infrared spectroscopy, elemental analyses, inherent viscosity (η_inh), solubility tests and specific rotation. Thermal properties of the PAIs 6(a-f) were investigated using thermal gravimetric analysis.     

Synthesis of aromatic poly(amide-imide)s from novel diimide-diacid (DIDA) containing sulphone and bulky pendant groups by direct polycondensation with various diamines

A novel diimide-diacid (DIDA) monomer, 4-{4-[(4-methyl phenyl) sulphonyl]}-1,3-bis-trimellitoimido benzene containing sulphone and bulky pendant groups was successfully synthesized and used to synthesize a series of wholly aromatic poly(amide-imide)s (PAIs) by direct polycondensation method. The direct polycondensation of newly synthesized DIDA with different diamines was carried out via Yamazaki’s phosphorylation method using triphenyl phosphite and pyridine system. The resulting poly(amide-imide)s were obtained in quantitative yields with inherent viscosities 0.36-0.47 dl/g in DMAc at 30 ± 0.1 °C. The poly(amide-imide)s were amorphous and were readily soluble in various solvents such as N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethylsulfoxide (DMSO), and pyridine. Tough and flexible films were obtained by casting their DMAc solution. According to thermogravimetric analysis, the polymers were fairly stable up to temperature around 396 °C, and 10% weight losses in the temperature range of 476-511 °C that showed good thermal stabilities of these polymers.     

Synthesis and characterization of optically active poly(amide-imide)s containing photosensitive chalcone units in the main chain

<正>A series of new optically active poly(amide-imide)s were synthesized by direct polycondensation reaction of 4,4'-diaminochalcone with several N-trimellitylimido-L-amino acids using a tosyl chloride(TsCl),pyridine(Py) and dimethylformamide(DMF) system as condensing agent.The resulting thermally stable poly(amide-imide)s were obtained in good to high yields and inherent viscosities ranging between 0.35 dL/g and 0.58 dL/g and were characterized with FTIR, ~1H-NMR,CHN,Ultraviolet,TGA and DTG techniques.     

Synthesis and characterization of phthalazinone containing poly(arylene ether)s via a novel N–C coupling reaction

High‐molecular‐weight poly(phthalazinone)s with very high glass‐transition temperatures (T_g's) were synthesized via a novel N–C coupling reaction. New bisphthalazinone monomers ( 7a–e ) were synthesized from 2‐(4‐chlorobenzoyl) phthalic acid in two steps. Poly(phthalazinone)s, having inherent viscosities in the range of 0.34–0.91 dL/g, were prepared by the reaction of the bis(phthalazinone) monomers with an activated aryl halide in a dipolar aprotic solvent in the presence of potassium carbonate. The poly(phthalazinone)s exhibited T_g's greater than 230 °C. polymer 8b synthesized from diphenyl biphenol and bis(4‐flurophenyl) sulfone demonstrated the highest T_g of 297 °C. Thermal stabilities of the poly(phthalazinone)s were determined by thermogravimetric analysis. All the poly(phthalazinone)s showed a similar pattern of decomposition with no weight loss below 450 °C in nitrogen. The temperatures of 5% weight loss were observed to be about 500 °C. The poly(phthalazinone)s containing 4,4′‐isopropylidenediphenol and 4,4′‐(hexafluoroisopropylidene) diphenol and diphenyl ether linkage were soluble in chlorinated solvents such as chloroform. Other poly‐(phthalazinone)s were soluble in dipolar aprotic solvents such as N,N′‐dimethylacetamide. The soluble poly(phthalazinone)s can be cast as flexible films from solution. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2481–2490, 2003     

New poly(amide-imide)s syntheses. I. Soluble high-temperature poly(amide-imide)s derived from 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene and various aromatic diamines

Novel aromatic poly(amide-imide)s with high inherent viscosities were prepared by direct polycondensation reaction of 2,5-bis(4-trimellitimidophenyl)-3,4-diphenylthiophene ( IV ) and aromatic diamines using triphenyl phosphite in the N-methyl–2-pyrrolidone (NMP)/pyridine solution containing dissolved CaCl₂. The diimide-diacid IV was readily obtained by the condensation reaction of 2,5-bis(4-aminophenyl)-3,4-diphenylthiophene ( III ₁) with trimellitic anhydride. The obtained poly(amide-imide)s showed high thermostability. Their decomposition temperatures at 10% weight loss in nitrogen atmospheres were above 550°C and the anaerobic char yield at 800°C ranged from 48 to 68%. Almost all the poly(amide-imide)s showed high glass transition temperatures above 300°C by differential scanning calorimetry (DSC) measurements. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed obvious yield points in the stress-strain curves and had strength at break up to 74.2 MPa, elongation to break up to 70.1%, and initial modulus up to 4.56 GPa. The factors affecting the reaction of diimide-diacid IV and 4,4′-oxydianiline in view of monomer concentration, reaction temperature, and amount of CaCl₂ were also investigated. © 1992 John Wiley & Sons, Inc.     

Synthesis and properties of poly(amide-imide)s based on the diimide-diacid condensed from 2,2′- bis(4-aminophenoxy)biphenyl and trimellitic anhydride

A new dicarboxylic acid having a kinked structure was synthesized from the condensation of 2,2′-bis(4-aminophenoxy)biphenyl and trimellitic anhydride. A series of biphenyl-2,2′-diyl-containing aromatic poly(amide-imide)s having inherent viscosities of 0.23–0.94 dL/g was prepared by the triphenyl phosphite activated polycondensation from the diimide-diacid II with various aromatic diamines in a medium consisting of N-methyl-2-pyrrolidone (NMP), pyridine, and calcium chloride. Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents including NMP and N,N-dimethylacetamide (DMAc). Transparent, flexible, and tough films of these polymers could be cast from DMAc or NMP solutions. The glass transition temperatures of these polymers were in the range of 227–261°C and the 10% weight loss temperatures were above 520°C in nitrogen. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1169–1177, 1998     

Synthesis and Characterization of High Performance Poly(amide-imide)s based on a New Diimide-diacide and Various Diamines

A new diimide-diacid, (4-(4-(2,6-diphenylpyridin-4yl)phenoxy)phenyl)-1,3-bis(trimellitimidobenzene) (PPMIB), was synthesized from the condensation reaction of a new diamine, (4-(4-(2,6-diphenylpyridin-4yl)phenoxy)phenyl)-3,5-diaminobezamide (PPDA), and trimellitic anhydride carboxylic acid (TMAA) in glacial acetic acid. The diimide-diacid (PPMIB) was characterized by FT-IR, ¹H-NMR and elemental analysis. A series of novel aromatic poly(amide-imide)s (PAIs) was synthesized by using direct polycondensation of PPMIB with various diamines in NMP in the presence of triphenylposphite and pyridine as condensing agents. The resulting PAIs were amorphous, readily soluble in many polar aprotic solvents and showed inherent viscosities of 0.35–0.50 dL/g. According to thermal analysis, these polymers exhibited glass transition temperatures (T_gs) in the range of 202–280°C and temperature of 10% weight loss (T₁₀) varied from 400 to 545°C in N₂. These polymers in NMP solution exhibited strong UV-Vis absorption maxima at 320°C nm and their fluorescence emission peaks appeared around 410–565 nm.     

The preparation of perfectly alternating poly(amide-imide)s via amide unit containing new diamine

The synthesis of N,N′-bis(4′-amino-4-biphenylene) isophthalamide (BABPI) and its applicability as a new diamine for the preparation of a series of new, high T_g, perfectly alternating poly(amide-imide)s is described. BABPI was synthesized from the catalytic reduction of the corresponding dinitro compound which was prepared by the condensation of isophthaloyl chloride and 4-amino-4′-nitrobiphenyl. The modified selective reduction technique was used for the preparation of 4-amino-4′-nitrobiphenyl from 4,4′-dinitro-biphenyl. Poly(amide-imide)s were synthesized by polycondensation of diamine BABPI with various commercially available aromatic dianhydrides via a conventional two-step procedure. In the first step, poly(amic-acid)s were prepared in a polar aprotic solvent, such as N-methyl pyrrolidone (NMP) at room temperature. Depending on the dianhydride used, intrinsic viscosities of poly(amic-acid)s were found to range between 0.43–0.69 dL/g. Bulk thermal imidization technique was used to obtain fully imidized poly(amide-imide)s at the second step. The synthesized poly(amide-imide)s showed good thermal stability up to 320°C and the 10% weight loss temperatures were recorded in the range of 525–550°C as evidenced by thermogravimetric analysis (TGA). The glass transition temperatures were found to be between 225–235°C from differential scanning calorimeter (DSC) measurements. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1149–1155, 1997     

Synthesis and properties of polyimides,polyamides and poly(amide-imide)s from ether diamine having the spirobichroman structure

A novel spirobichroman unit containing dietheramine, 6,6′-bis(4-aminophenoxy)-4,4,4′,4′,7,7′-hexamethyl-2,2′-spirobichroman ( 3 ), was prepared by the nucleophilic substitution of 6,6′-dihydroxy-4,4,4′,4′,7,7′-hexamethyl-2,2′-spirobichroman with p-chloronitrobenzene in the presence of K₂CO₃ followed by hydrazine catalytic reduction of the intermediate dinitro compound. A series of polyimides were synthesized from diamine 3 and various aromatic dianhydrides by a conventional two-stage procedure through the formation of poly(amic-acid)s followed by thermal imidization. The intermediate poly(amic-acid)s had inherent viscosities of 1.00–2.78 dL/g. All the poly-(amic-acid)s could be thermally cyclodehydrated into flexible and tough polyimide films, and some polyimides were soluble in polar solvents such as N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc), and N,N-dimethylformamide (DMF). These polyimides had glass transition temperatures (T_g) in the range of 236–256°C, and 10% weight loss occurred up to 450°C. Furthermore, a series of polyamides and poly(amide-imide)s with inherent viscosities of 0.71–2.29 dL/g were prepared by direct polycondensation of the diamine 3 with various aromatic dicarboxylic acids and imide ring-containing dicarboxylic acids by means of triphenyl phosphite and pyridine. All the polyamides and poly(amide-imide)s were readily soluble in polar solvents such as DMAc, and tough and flexible films could be cast from their DMAc solutions. These polymers had glass transition temperatures in the range of 137–228°C and 10% weight loss temperatures in the range of 419–443°C in air and 404–436°C in nitrogen, respectively. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1487–1497, 1997