Synthesis and characterization of near‐monodisperse electron acceptor homopolymers of 2‐[(3,5‐dinitrobenzoyl)oxy]ethyl methacrylate

Homopolymers of 2‐(trimethylsiloxy)ethyl methacrylate of degrees of polymerization from 5 to 50 were synthesized by group transfer polymerization in tetrahydrofuran (THF) using 1‐methoxy‐1‐(trimethylsiloxy)‐2‐methyl propene as the initiator and tetrabutylammonium bibenzoate as the catalyst. These polymers were first converted to poly[2‐(hydroxy)ethyl methacrylate]s by removal of the trimethylsilyl‐protecting groups by acidic hydrolysis, and subsequently transformed to poly{2‐[(3,5‐dinitrobenzoyl)oxy]ethyl methacrylate}s by reaction with 3,5‐dinitrobenzoyl chloride in the presence of triethylamine. Gel permeation chromatography in THF and proton nuclear magnetic resonance (¹H NMR) spectroscopy in CDCl₃ and d₆ dimethyl sulfoxide were used to characterize the polymers in terms of their molecular weight and composition. The molecular weights were found to be close to the values expected from the polymerization stoichiometry and the molecular weight distributions were narrow, with polydispersity indices around 1.1. The hydrolysis and reesterification steps were found to be almost quantitative for all polymers. Differential scanning calorimetry and thermal gravimetric analysis were also employed to measure the glass transition temperatures (T_g 's) and decomposition temperatures, which were determined to be approximately 80 and 320 °C, respectively. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1457–1465, 2000     

Near‐monodisperse,catalytically active,imidazole‐containing homooligomers: Synthesis by group transfer polymerization and solution characterization

Oligomers covering degrees of polymerization up to 23 of 2‐(1‐imidazolyl)ethyl methacrylate (ImEMA) were synthesized by group transfer polymerization (GTP) in propylene carbonate and tetrahydrofuran (THF). While GTP proceeds smoothly in propylene carbonate, polymerization in THF is accompanied by oligomer precipitation. The molecular weights (MWs) and molecular weight distributions (MWDs) of the oligomers were obtained by gel permeation chromatography (GPC) using acidic aqueous sodium nitrate as the eluent. Good control over the MW and small polydispersity indices (PDIs) were measured for the oligomers prepared in propylene carbonate but not in THF. The oligomers were evaluated for their ability to hydrolyze 4‐nitrophenyl acetate in aqueous solution. The hydrolytic activity increased with oligomer MW. The oligomer concentration‐ and substrate concentration‐dependencies of the initial hydrolysis rate were both found to be approximately first order. The hydrolytic activity increased with an increase in pH, manifesting the enhanced nucleophilicity and pronounced hydrophobicity of the unprotonated form of the repeating units. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1501–1512, 1999     

“Smart” poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) copolymers synthesized by nitroxide mediated radical polymerization

A series of poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) (poly(DMAEMA‐ran‐VBK)) random copolymers, with VBK molar feed compositions f_VBK,0 = 0.02–0.09, were synthesized using 10 mol % [tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino] nitroxide (SG1) relative to 2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropionic acid (BlocBuilder) at 80 °C and 90 °C. Controlled polymerizations were observed, even with f_VBK,0 = 0.02, as reflected by a linear increase in number average molecular weight (M_n) versus conversion X ≤ 0.6 with final copolymers characterized by relatively narrow, monomodal molecular weight distributions (M_w/M_n ≈ 1.5). Poly(DMAEMA‐ran‐VBK) copolymers were deemed sufficiently pseudo‐“living” to reinitiate a second batch of N,N‐dimethylacrylamide (DMAA), with very few apparent dead chains, as indicated by the monomodal shift in the gel permeation chromatography chromatograms. Poly(DMAEMA‐ran‐VBK) random copolymers exhibited tuneable lower critical solution temperature (LCST), in aqueous solution, by modifying copolymer composition, solution pH and by the addition of the water‐soluble poly(DMAA) segment. ¹H NMR analysis determined that, in water, the VBK units of the poly(DMAEMA‐ran‐VBK) random copolymer were segregated to the interior of the copolymer aggregate regardless of solution temperature and that poly(DMAEMA‐ran‐VBK)‐b‐poly(DMAA) block copolymers formed micelles above the LCST. In addition, the final random copolymer and block copolymer exhibited temperature dependent fluorescence due to the VBK units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

pH‐ and temperature‐sensitive statistical copolymers poly[2‐(dimethylamino)ethyl methacrylate‐stat‐2‐vinylpyridine] with Functional succinimidyl‐ester chain ends synthesized by nitroxide‐mediated polymerization

Statistical copolymerizations of 2‐(dimethylamino)ethyl methacrylate (DMAEMA) with 2‐vinylpyridine (2VP) with 80 to 99 mol % DMAEMA in the feed utilizing a succinimidyl ester‐terminated alkoxyamine unimolecular initiator (NHS‐BlocBuilder) at 80 °C in bulk were performed. The effectiveness of 2VP as a controlling comonomer is demonstrated by linear increases in number‐average molecular weight versus conversion, relatively low PDI (1.5–1.6 with up to 98% DMAEMA) and successful chain extensions with 2VP. Additional free nitroxide does not significantly improve control for the DMAEMA/2VP copolymerizations. The succinimidyl ester on the initiator permits coupling to amine‐terminated poly(propylene glycol) (PPG), yielding an effective macroinitiator for synthesizing a doubly thermo‐responsive block copolymer of PPG‐block‐P(DMAEMA/2VP). A detailed study of the thermo‐ and pH‐sensitivities of the statistical and block copolymers is also presented. The cloud point temperature of the statistical copolymers is fine tuned from 14 to 75 °C by varying polymer composition and pH. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012.     

Synthesis of ω‐ and α,ω‐sulfonatotelechelics based on homopolymers and block copolymers of n‐butyl methacrylate and t‐butyl methacrylate

The synthesis of ω‐ and α,ω‐telechelics with sulfonate end groups through the sulfoalkylation of homopolymers and block copolymers of n‐butyl methacrylate and t‐butyl methacrylate with 1,3‐propane sultone is described. The polymerizations are initiated in tetrahydrofuran at −78 °C with either 1,1‐diphenyl‐3‐methylpentyllithium or dilithium 1,1,4,4‐tetraphenylbutane to obtain monofunctional or difunctional polymethacrylate anions, respectively. Narrow molecular weight distributions are obtained for the homopolymers and copolymers in the presence of LiCl in a 10/1 ratio relative to the initiator. The direct reaction of the poly(n‐butyl methacrylate) anions with the sultone results in low functionalization levels: f = 0.24–0.29 for the monofunctional anions and f = 0.32–0.35 for the difunctional anions. The reaction of the poly(t‐butyl methacrylate) anions or end‐capping of the poly(n‐butyl methacrylate) anions with t‐butyl methacrylate units before sulfoalkylation yields telechelics with f = 0.81–1.0 for the monofunctional anions and f = 1.74–1.94 for the difunctional anions. The telechelic polymers, purified by ultrafiltration, have been characterized by size exclusion chromatography, Fourier transform infrared, and ¹H NMR spectroscopy. The yield of the sulfoalkylation reactions, determined by colorimetric analysis of a complex formed with methylene blue, is in good agreement with the results obtained by nonaqueous titration of the acidified telechelics. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3711–3721, 2000     

Cyclopolymerization of α,ω‐heterodifunctional monomers containing styrene and maleimide moieties

A series of α,ω‐heterodifunctional monomers with styrene (St) and maleimide moieties bridged by a varied length of oligo‐ethylene glycol (OEG) linkers were synthesized. Cyclopolymerizations of these monomers through reversible addition–fragmentation chain transfer‐mediated alternating radical copolymerization between intramolecular St and maleimide moieties were investigated. For the monomers with three or more ethylene glycol (EG) units, their cyclopolymerizations can be realized properly in low monomer feeding concentrations, affording well‐defined cyclopolymers with crown ether encircled in their main chains. Importantly, the cyclopolymerizations of monomers with six or seven EG units in the presence of KPF₆ could be enhanced by the supramolecular effects between the OEG linkers and the potassium metal ion. Thus, the monomer feeding concentration could be largely improved, which may benefit preparation of the cyclopolymers with high degrees of copolymerization. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 330–338     

Functionalization of the active chain ends of poly(vinyl chloride) obtained by single‐electron‐transfer/degenerative‐chain‐transfer mediated living radical polymerization: Synthesis of telechelic α,ω‐di(hydroxy)poly(vinyl chloride)

The chloroiodomethyl chain ends of poly(vinyl chloride) (PVC) obtained by the single‐electron‐transfer/degenerative‐chain‐transfer mediated living radical polymerization of vinyl chloride initiated with iodoform were quantitatively functionalized by the reaction with 2‐allyloxyethanol (CH₂?CHCH₂OCH₂CH₂OH). This reaction was performed in dimethyl sulfoxide at 70 °C and was catalyzed by sodium dithionite/sodium bicarbonate. The resulting product is the first example of telechelic PVC [α,ω‐di(hydroxy)PVC]. A possible mechanism for this reaction was suggested. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1255–1260, 2005     

End‐linked amphiphilic polymer conetworks: Synthesis by sequential atom transfer radical polymerization and swelling characterization

Conetworks based on end‐linked homopolymers and amphiphilic gradient copolymers were synthesized by the atom transfer radical polymerization (ATRP) of 2‐(dimethylamino)ethyl methacrylate (DMAEMA, hydrophilic monomer), methyl methacrylate (MMA, hydrophobic monomer), and ethylene glycol dimethacrylate (EGDMA, hydrophobic cross‐linker). Sequential, rather than step‐wise polymerizations, were performed to enhance the livingness of the polymerization, particularly for the end‐linking step, and to ultimately obtain conetworks based on gradient rather than pure block copolymers. Amphiphilic conetworks based on end‐linked MMA‐DMAEMA‐MMA gradient copolymers of different compositions were successfully synthesized as confirmed by the narrow molecular weight distributions of the linear precursors, the rigidity of the amphiphilic conetwork products and the low sol‐fraction extracted from the conetworks. Similarly successful was the ATRP synthesis of an end‐linked conetwork based on a DMAEMA‐MMA statistical copolymer and of a randomly cross‐linked conetwork that resulted from the simultaneous terpolymerization of DMAEMA, MMA and EGDMA. An amphiphilic conetwork based on an end‐linked DMAEMA‐MMA‐DMAEMA gradient copolymer presented a less rigid, mucous‐like, texture. The degrees of swelling (DS) in tetrahydrofuran of all the conetworks were higher than those measured in pure water, whereas the aqueous DS values increased by lowering the pH and increasing the DMAEMA content of the conetworks. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1878–1886, 2010     

Synthesis and characterization of secondary‐amine‐functional microparticles

Secondary‐amine‐functional microparticles were prepared in the range of 50–250 μm through the suspension polymerization of styrene, divinylbenzene (DVB), and 2‐(tert‐butylamino)ethyl methacrylate (tBAEMA). This study focused on the effects of the DVB, tBAEMA, initiator, and stabilizer concentrations and shaking rate on the experimental amine content, swelling ratio, average particle size, and particle size distribution. The suspension polymerization experiments were carried out in two different systems. In the first system, an organic phase, including the monomers and initiator, was dispersed in an aqueous medium in the presence of Al₂(SO₄)₃. Al₂(SO₄)₃, in the presence of an amine monomer (pH ～ 10), formed colloidal Al(OH)₃, which built a nonsticky layer on the surface of the polymerizing droplets that prevented them from coalescing and aggregating. Individual and spherical particles within the range of 50–200 μm were obtained by this polymerization method. The second method was similar to the first polymerization protocol, except that a certain amount of sodium dodecyl sulfate was added as a costabilizer in the presence of Al₂(SO₄)₃. In these experiments, individual and spherical particles were obtained within the range of 130–250 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem: 3708–3719, 2004     

Novel block ionomers II. Synthesis and characterization of polyisobutylene‐based block cationomers

Various novel block cationomers consisting of polyisobutylene (PIB) and poly[2‐(dimethylamino)ethyl methacrylate] (PDMAEMA) segments were synthesized and characterized. The specific targets were various molecular weight diblocks (PIB‐b‐PDMAEMA⁺) and triblocks (PDMAEMA⁺‐b‐PIB‐b‐PDMAEMA⁺), with the PIB blocks in the DP_n = 50–200 range (number‐average molecular weight = 3,000–9000 g/mol) connected to blocks of PDMAEMA⁺ cations in the DP_n = 5–20 range (where DP is the number‐average degree of polymerization). The overall synthetic strategy for the preparation of these block cationomers had four steps: (1) synthesis by living cationic polymerization of mono‐ and diallyltelechelic polyisobutylenes, (2) end‐group transformation to obtain PIBs fitted with termini capable of mediating the atom transfer radical polymerization (ATRP) of DMAEMA, (3) ATRP of DMAEMA, and (4) quaternization of PDMAEMA to PDMAEMA ⁺I^? by CH₃I. Scheme 1 shows the microarchitecture and outlines the synthesis route. Kinetic and model experiments provided guidance for developing convenient synthesis methods. The microarchitecture of PIB–PDMAEMA di‐ and triblocks and the corresponding block cationomers were confirmed by ¹H NMR and FTIR spectroscopy and solubility studies. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3679–3691, 2002     

Novel C60‐Anchored Two‐Armed Poly(tert‐butyl acrylate): Synthesis and Characterization

Summary: A multistep synthetic procedure for preparing novel C₆₀‐anchored two‐armed poly(tert‐butyl acrylate) was developed. First, two‐armed poly(tert‐butyl acrylate) bearing a malonate ester core with well‐controlled molecular weight was synthesized through atom transfer radical polymerization. The effective Bingel reaction between C₆₀ and the well‐defined polymer was then carried out to yield C₆₀‐anchored polymer. GPC, ¹H NMR, and UV‐vis spectroscopy indicated that the C₆₀‐anchored polymer was a monosubstituted and ‘closed’ 6,6‐ring‐bridged methanofullerene derivative.

Schematic of a novel C₆₀‐anchored two‐armed polymer.     

Degradable multisegmented polymers synthesized by consecutive radical addition‐coupling reaction of α,ω‐macrobiradicals and nitroso compound

A consecutive radical addition‐coupling reaction induced by spin‐trapping agent is applied to produce degradable multisegmented polymer using α,ω‐dibromo polymer as a precursor. The macroradical generated by single electron transfer process catalyzed by Cu/PMDETA from α,ω‐dibromo polymer can be efficiently captured by 2‐methyl‐2‐nitrosopropane (MNP), which results in nitroxide radical. The in situ formed nitroxide radical immediately undergoes cross‐coupling reaction with polymeric radical, generating block polymer bridged with alkoxyamine moiety. The consecutive radical addition‐coupling reaction generates multisegmented polymer via step‐growth mechanism. Different multisegmented polymers have been prepared from α,ω‐dibromo‐PS, PtBA, and PtBA‐PS‐PtBA. The block number of multisegmented polymers can be tailored by varying the feed ratio of α,ω‐dibromo precursor to MNP. The multisegmented polymer can be degraded in the presence of hydrogen atom donor or air, and the molecular weight distribution transformed back into shape of its original precursor as it is conjugated by alkoxyamine moieties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Well‐defined poly[(dimethylamimo)ethyl methacrylate]‐b‐poly(fluoroalkyl methacrylate) diblock copolymers: Effects of different fluoroalkyl groups on the solution properties

A series of well‐defined, fluorinated diblock copolymers, poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,2‐trifluoroethyl methacrylate) (PDMA‐b‐PTFMA), poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,3,4,4,4‐hexafluorobutyl methacrylate) (PDMA‐b‐PHFMA), and poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(2,2,3,3,4,4,5,5‐octafluoropentyl methacrylate) (PDMA‐b‐POFMA), have been synthesized successfully via oxyanion‐initiated polymerization. Potassium benzyl alcoholate (BzO^?K⁺) was used to initiate DMA monomer to yield the first block PDMA. If not quenched, the first living chain could be subsequently used to initiate a feed F‐monomer (such as TFMA, HFMA, or OFMA) to produce diblock copolymers containing different poly(fluoroalkyl methacrylate) moieties. The composition and chemical structure of these fluorinated copolymers were confirmed by ¹H NMR, ¹⁹F NMR spectroscopy, and gel permeation chromatography (GPC) techniques. The solution behaviors of these copolymers containing (tri‐, hexa‐, or octa‐ F‐atom)FMA were investigated by the measurements of surface tension, dynamic light scattering (DLS), and UV spectrophotometer. The results indicate that these fluorinated copolymers possess relatively high surface activity, especially at neutral media. Moreover, the DLS and UV measurements showed that these fluorinated diblock copolymers possess distinct pH/temperature‐responsive properties, depending not only on the PDMA segment but also on the fluoroalkyl structure of the FMA units. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2702–2712, 2009     

Facile synthesis of controlled‐structure primary amine‐based methacrylamide polymers via the reversible addition‐fragmentation chain transfer process

We report here a novel direct method for the syntheses of primary aminoalkyl methacrylamides that requires mild reagents and no protecting group chemistry. The reversible addition‐fragmentation chain transfer polymerization (RAFT) of the aminoalkyl methacrylamide revealed to be highly efficient with 4‐cyanopentanoic acid dithiobenzoate (CTP) as chain transfer agent and 4,4′‐azobis(4‐cyanovaleric acid) (ACVA) as initiator. Cationic amino‐based homopolymers of reasonably narrow polydispersities (M_w/M_n < 1.30) and predetermined molecular weights were obtained without recourse to any protecting group chemistry. A range of block and random copolymers were also synthesized via the RAFT process. The homopolymers and copolymers were characterized by aqueous conventional and triple detection gel permeation chromatography systems. Furthermore, the primary amine‐based methacrylamide monomers and polymers revealed to be highly stable both with the primary amino group in the protonated and deprotonated form. We have also demonstrated that stabilized gold nanoparticles can be generated with the RAFT‐synthesized amine‐based polymers via a photochemical process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4984–4996, 2008     

Synthesis and Characterization of α,ω‐Heterofunctional Poly(ethylene oxide) Macromonomers

A novel α,ω‐heterofunctional poly(ethylene oxide) (PEO) macromonomer possessing methacryloyl and thienyl end groups was prepared by ring‐opening polymerization of ethylene oxide initiated by potassium thienylethoxide and termination of the living PEO ends with methacryloyl chloride. Incorporation of methacryloyl and thienyl groups was confirmed by free‐radical and oxidative polymerization processes, respectively, and by means of ¹H NMR analysis.

     

Visible light‐induced thiol‐ene reaction: A new strategy to prepare Α,ω‐dithiol and Α,ω‐divinyl telechelic polythiolether oligomers

A new strategy is developed to prepare both α,ω‐dithiol and α,ω‐divinyl linear telechelic polythiolether oligomers by visible light induced thiol‐ene chemistry in the presence of a fac‐Ir(ppy)₃ photoredox catalyst. Polythiolether oligomers of well‐defined end groups and controlled molecular weights have been successfully synthesized at varying monomer molar ratios of 1,4‐benzenedimethanethiol (BDMT) to diethylene glycol divinyl ether (DEGVE). ¹H NMR and MALDI‐TOF MS analyses demonstrate that as‐prepared polythiolethers possess high end‐group fidelity, which is further supported by the successful polyaddition of polythiolethers bearing α,ω‐dithiol and α,ω‐divinyl groups. For example, with the α,ω‐dithiol‐ (M_n = 1900 g mol^?1, PDI = 1.25) and α,ω‐divinyl‐terminated (M_n = 2000 g mol^?1, PDI = 1.29) polythiolethers as macromonomers, the molecular weight of resulting polythiolether is up to 7700 g mol^?1 with PDI as 1.67. The reactivity of the terminal thiol group is further confirmed by the addition reaction with N‐(1‐pyrenyl)maleimide. UV‐vis spectra and fluorescene measurements suggest that fac‐Ir(ppy)₃ undergo a redox quenching process reacted with BDMT to generate thiyl free radicals. With these results, the mechanism of the thiol‐ene reaction catalyzed by photoredox catalyst is proposed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 740–749     

Aminated PCL‐based copolymers by chemical modification of poly(α‐iodo‐ε‐caprolactone‐co‐ε‐caprolactone)

A novel method is proposed to access to new poly(α‐amino‐ε‐caprolactone‐co‐ε‐caprolactone) using poly(α‐iodo‐ε‐caprolactone‐co‐ε‐caprolactone) as polymeric substrate. First, ring‐opening (co)polymerizations of α‐iodo‐ε‐caprolactone (αIεCL) with ε‐caprolactone (εCL) are performed using tin 2‐ethylhexanoate (Sn(Oct)₂) as catalyst. (Co)polymers are fully characterized by ¹H NMR, ¹³C NMR, FTIR, SEC, DSC, and TGA. Then, these iodinated polyesters are used as polymeric substrates to access to poly(α‐amino‐ε‐caprolactone‐co‐ε‐caprolactone) by two different strategies. The first one is the reaction of poly(αIεCL‐co‐εCL) with ammonia, the second one is the reduction of poly(αN₃εCL‐co‐εCL) by hydrogenolysis. This poly(α‐amino‐ε‐caprolactone‐co‐ε‐caprolactone) (F_αNH2εCL < 0.1) opens the way to new cationic and water‐soluble PCL‐based degradable polyesters. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6104–6115, 2009     

Kinetic simulations for cyclization of α,ω‐telechelic polymers

In this work, we conducted kinetic simulations to examine the effects of various experimental conditions on cyclization during the feed of α,ω‐telechelic polymers into a reaction mixture. The simulations showed that the interplay between the feed rate and rate coefficients for cyclization and multiblock formation were the dominant and controlling parameters. The simulations were in good agreement with previously published results on cyclization of α,ω‐telechelic polystyrene with different molecular weights by the Cu‐catalyzed azide/alkyne cycloaddition (CuAAC) reaction. They also showed that high dilution was not a necessary condition for cyclization and that high percentages of monocyclic could be rapidly produced in solutions that are more concentrated. Previously reported work demonstrated that cyclic polystyrene could be prepared in less than 9 min at 25 °C using the CuAAC “click” reaction. These simulations allow for optimization and better experimental design, leading to the possibility of large scale production of cyclic polymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Modification of the ω‐bromo end group of poly(methacrylate)s prepared by copper(I)‐mediated living radical polymerization

Four different approaches to introduce a specific functional group at the ω terminus of poly(methacrylate)s (PMMAs) prepared via copper(I)bromide/pyridinalimine‐mediated atom transfer polymerization, under polymerization conditions, are reported. Method 1 involves the homolysis of the ω‐C Br bond with a subsequent reaction, via coupling or disproportionation, with an external radical species. The reaction with 2,2,6,6‐tetramethylpiperidin‐N‐oxyl shows a high conversion (>78%) of the ω‐bromo PMMA chains into their corresponding macromonomer analogues. Method 2 utilizes monomers that are able to undergo radical addition followed by subsequent fragmentation. Reactions with trimethyl[1‐(trimethylsiloxy)phenylethenyloxy]silane and allyl bromide show quantitative and 57% transformation, respectively. Method 3 is the reaction of a monomer that yields a relatively more stable secondary, or primary, carbon–halogen bond. Reactions with divinylbenzene, n‐butylacrylate, and ethylene showed quantitative, 62%, and quantitative additions, respectively. Method 4 is the addition of nonhomopropagating monomers, that is, maleic anhydride. This reaction proceeds quantitatively. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2678–2686, 2000