Synthesis and properties of 4,4′-biphenyldicarboxylic acid and 2,6-naphthalenedicarboxylic acid

This article describes the synthesis and the properties of polyesters and copolyesters prepared from ethylene glycol, terephthalic acid, 4,4′ biphenyldicarboxylic acid (BDA), and 2,6-naphthlenedicarboxylic acid (NDA). The effect of incorporating varying levels of BDA and NDA on polyethylene terephthalate (PET) is described. Depending on the concentration, incorporation of BDA into PET leads to an improvement in glass transition temperature (T_g), strength, modulus, and barrier properties. Copolymers of PET containing up to about 50% BDA derived units are clear and have T_g's ranging from 85 to 105°C, making them suitable for applications where a high T_g along with clarity is important. Copolymers with higher BDA concentration are highly crystalline, with high rates of crystallization from the melt. Copolymerization of NDA with oligoethyleneterephthalate leads to copolymers that are generally amorphous. Crystallinity can be developed in copolymers with low concentration of NDA by thermal annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3139–3146, 1999     

LC-Polyimides. 22. Thermotropic Poly(Amide-Imide)s Derived from New Bisimide Spacers and Biphenyl-4,4′-dicarboxylic Acids

Abstract

A new class of diamine spacers was synthesized from α,ω-diaminoalkanes and 4-nitrophthalic anhydride. The resulting α,ω-bis(4-aminophthalimido)alkanes were polycondensed with terephthaloylchloride, 2-phenylthioterephthaloylchloride, naphthalene-2,6-dicarboxylic acid dichloride, and 4,4′-biphenyl dicarboxylic acid dichloride. Most poly(amide-imide)s proved to be semicrystalline, forming a smectic layer structure in the solid state. Yet only the poly(amide-imide)s derived from 4,4′-biphenyl dicarboxylic acid are thermotropic and form a smectic and a nematic LC-phase. Due to the high temperatures employed, the reversibility of the phase transitions suffers from thermal degradation.     

Poly(ethylene terephthalate) reinforced by N,N′‐diphenyl biphenyl‐3,3′,4,4′‐tetracarboxydiimide moieties

Starting with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride and methyl aminobenzoate, we synthesized a novel rodlike imide‐containing monomer, N,N′‐bis[p‐(methoxy carbonyl) phenyl]‐biphenyl‐3,3′,4,4′‐tetracarboxydiimide (BMBI). The polycondensation of BMBI with dimethyl terephthalate and ethylene glycol yielded a series of copoly(ester imide)s based on the BMBI‐modified poly(ethylene terephthalate) (PET) backbone. Compared with PET, these BMBI‐modified polyesters had higher glass‐transition temperatures and higher stiffness and strength. In particular, the poly(ethylene terephthalate imide) PETI‐5, which contained 5 mol % of the imide moieties, had a glass‐transition temperature of 89.9 °C (11 °C higher than the glass‐transition temperature of PET), a tensile modulus of 869.4 MPa (20.2 % higher than that of PET), and a tensile strength of 80.8 MPa (38.8 % higher than that of PET). Therefore, a significant reinforcing effect was observed in these imide‐modified polyesters, and a new approach to higher property polyesters was suggested. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 852–863, 2002; DOI 10.1002/pola.10169     

Synthesis and photochemical properties of poly(ester–amide)s containing norbornadiene (NBD) residues

N,N′‐Bis[(3‐carboxynorbornadien‐2‐yl)carbonyl]‐N,N′‐diphenylethylenediamine (BNPE) was synthesized in 70% yield by the reaction of 2,5‐norbornadiene‐2,3‐dicarboxylic acid anhydride with N,N′‐diphenylethylenediamine. Other dicarboxylic acid derivatives containing norbornadiene (NBD) residues having N,N′‐disubstituted amide groups were also prepared by the reaction of 2,5‐NBD‐2,3‐dicarboxylic acid anhydride with certain secondary diamines. When the polyaddition of BNPE with bisphenol A diglycidyl ether (BPGE) was carried out using tetrabutylammonium bromide as a catalyst in N‐methyl‐2‐pyrrolidone at 100°C for 12 h, a polymer with number average molecular weight of 69,800 was obtained in 98% yield. Polyadditions of other NBD dicarboxylic acid derivatives containing N,N′‐disubstituted amide groups with BPGE were also performed under the same conditions. The reaction proceeded very smoothly to give the corresponding NBD poly(ester–amide)s in good yields. Photochemical reactions of the obtained polymers with N,N′‐disubstituted amide groups on the NBD residue were examined, and it was found that these polymers were effectively sensitized by adding appropriate photosensitizers such as 4‐(N,N‐dimethylamino)benzophenone and 4,4′‐bis(N,N‐diethylamino)benzophenone in the film state. The stored energies in the quadricyclane groups of the polymers were also evaluated to be about 94 kJ/mol by DSC measurement of the irradiated polymer films. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 917–926, 1999     

Comparison of statistical and blocky copolymers of ethylene terephthalate and ethylene 4,4′‐bibenzoate based on thermal behavior and oxygen transport properties

Poly(ethylene terephthalate) (PET) was blended with a frustrated liquid‐crystalline polymer, poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) (PETBB55), in the weight ratio 70:30. Under the melt conditions used for blending, NMR analysis showed that some transesterification had occurred. Accordingly, the blended product resembled a blocky copolymer more closely than it did a physical blend. A random copolymer with the same composition was synthesized for comparison. The study examined the effect of the comonomer distribution (blocky vs random) on the thermal behavior and oxygen transport properties of the glassy and cold‐drawn polymers. The glass‐transition temperatures and the crystallization behavior suggested that the PETBB55 blocks phase‐separated as very small domains. Higher levels of orientation, as indicated by higher densities and higher trans glycol fractions, were achieved by the cold drawing of the blocky copolymer. It was speculated that the cold drawing of the blocky copolymer at temperatures up to the glass‐transition temperature of the PETBB55 blocks produced highly oriented PETBB55 domains. Constraints imposed by connections between PET and the PETBB55 blocks prevented the relaxation of the continuous PET phase, even at temperatures well above the glass‐transition temperature of the PET blocks. In this sense, the blocky copolymer embodied the concept of a self‐reinforcing polymer. As a result, an improved oxygen barrier was obtained over a wider range of cold‐draw temperatures with the blocky copolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 289–307, 2003     

Synthesis and characterization of poly(benzobisthiazole) with tetramethylbiphenyl moiety in the main chain

Poly(benzobisthiazole)s containing an ortho-tetramethyl substituted biphenyl moiety were synthesized via the polycondensation of 2,5-diamino-1,4-benzenedithiol dihydrochloride with 2,2′,6,6′-tetramethylbiphenyl-4,4′-dicarboxylic acid in poly(phosphoric acid) (PPA). The intrinsic viscosities of the tetramethylbiphenyl poly-(benzobisthiazole)s in chlorosulfonic acid at 30°C were in the range of 6.9–13.4 dL/g. Copolycondensation of 2,5-diamino-1,4-benzenedithiol dihydrochloride with terephthalic acid and 2,2′,6,6′-tetramethylbiphenyl-4,4′-dicarboxylic acid was carried out as well by varying the ratio of the two dicarboxylic acid monomers in the reactant mixture. The homopolymers and copolymers were characterized by Fourier transform infrared spectroscopy (FTIR) and ¹³C solid-state nuclear magnetic resonance spectroscopy (NMR). Thermal stability of the polymers was evaluated by thermogravimetric analysis (TGA) and thermogravimetric mass spectrum analysis (TG-MS). The tetramethylbiphenyl poly(benzobisthiazole)s were found to be more stable at elevated temperatures than the parent poly(p-phenylene benzobisthiazole) (PBZT). © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1407–1416, 1998     

Synthesis and properties of noncoplanar rigid‐rod aromatic polyhydrazides and poly(1,3,4‐oxadiazole)s containing phenyl or naphthyl substituents

Two new phenyl‐ and naphthyl‐substituted rigid‐rod aromatic dicarboxylic acid monomers, 2,2′‐diphenylbiphenyl‐4,4′‐dicarboxylic acid ( 4 ) and 2,2′‐di(1‐naphthyl)biphenyl‐4,4′‐dicarboxylic acid ( 5 ), were synthesized by the Suzuki coupling reaction of 2,2′‐diiodobiphenyl‐4,4′‐dicarboxylic acid dimethyl ester with benzeneboronic acid and naphthaleneboronic acid, respectively, followed by alkaline hydrolysis of the ester groups. Four new polyhydrazides were prepared from the dicarboxylic acids 4 and 5 with terephthalic dihydrazide (TPH) and isophthalic dihydrazide (IPH), respectively, via the Yamazaki phosphorylation reaction. These polyhydrazides were amorphous and readily soluble in many organic solvents. Differential scanning calorimetry (DSC) indicated that these hydrazide polymers had glass transition temperatures in the range of 187–234 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the range of 300–400 °C. The resulting poly(1,3,4‐oxadiazole)s exhibited T_g's in the range of 252–283 °C, 10% weight‐loss temperature in excess of 470 °C, and char yield at 800 °C in nitrogen higher than 54%. These organo‐soluble polyhydrazides and poly(1,3,4‐oxadiazole)s exhibited UV–Vis absorption maximum at 262–296 and 264–342 nm in NMP solution, and their photoluminescence spectra showed maximum bands around 414–445 and 404–453 nm, respectively, with quantum yield up to 38%. The electron‐transporting properties were examined by electrochemical methods. Cyclic voltammograms of the poly(1,3,4‐oxadiazole) films cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited reversible reduction redox with E_onset at ?1.37 to ?1.57 V versus Ag/AgCl in dry N,N‐dimethylformamide solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6466–6483, 2006     

Aromatic polyamides and polyimides derived from 3,3′-diaminobiphenyl: Synthesis,characterization, and molecular simulation study

In this article a new synthesis of 3,3′-diaminobiphenyl (3,3′-DABP) is described, along with the preparation and characterization of polyamides and polyimides based on it. Reactivity of this monomer was calculated by a molecular simulation study, using ab initio quantum-mechanical methods. Terephthaloyl and isophthaloyl chloride were used for the synthesis of polyamides, while 3,3′,4,4′-biphenylenetetracarboxylic acid dianhydride and 4,4′-(hexafluoroisopropylidene) diphthalic anhydride were used for the synthesis of polyimides. Medium to high molecular weight polymers were attained, with inherent viscosities near or higher than 1.0 dL/g, the solubility of the 3,3′-DABP polymers was much better than that of the homologous polymers from benzidine (4,4′-DABP), the glass-transition temperatures were lower, by about 40°C, and the thermal resistance, as measured by thermogravimetry, was virtually the same. Amorphous films, made from cast polymer solutions, showed excellent mechanical properties, comparable to conventional aromatic polyamides and polyimides. Theoretical calculations demonstrated that the radius of giration, end-to-end distance and density of poly(3,3′-DABP-isophthalamide) were lower than those of poly(4,4′-DABP-isophthalamide), as a consequence of the chain folding induced in the backbone by the m-substitution in 3,3′-DABP. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4646–4655, 1999     

Solubility parameters of poly(sulfonyldiphenylene phenylphosphonate) and its miscibility with poly(ethylene terephthalate)

The solubility behaviors of poly(sulfonyldiphenylene phenylphosphonate) (PSPPP), a very efficient flame retardant for poly(ethylene terephthalate) (PET), in more than 50 solvents were examined. Its solubility parameters (δ) were determined by the intrinsic viscosity and turbidic titration methods. The two methods obtained consistent results, δ = 21.0–21.6 J^1/2/cm^3/2 and δ = 21.0 J^1/2/cm^3/2, and the three‐dimensional solubility parameters were δ_d = 18.9 J^1/2/cm^3/2, δ_p = 8.8 J^1/2/cm^3/2, and δ_h = 5.9 J^1/2/cm^3/2. The miscibility of PSPPP with PET was estimated by the calculation of the heats of mixing, which were related to the difference between the solubility parameters of PSPPP and PET. Fourier transform infrared was used to examine the interactions between PSPPP and PET macromolecules, which were the internal factors of polymer–polymer miscibility. The results showed that PSPPP and PET were miscible within a very wide composition range, especially with less than 15 wt % PSPPP, a composition of interest for the preparation of flame‐retardant PET. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2296–2301, 2003     

Synthesis and properties of organosoluble poly(amide imide imide)s based on tetraimide dicarboxylic acid condensed from 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, 4,4′‐oxydianiline,and trimellitic anhydride and various aromatic diamines

A novel tetraimide dicarboxylic acid was synthesized with the ring‐opening addition of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, 4,4′‐oxydianiline, and trimellitic anhydride in a 1/2/2 molar ratio in N‐methyl‐2‐pyrrolidone followed by azeotropic condensation to tetraimide dicarboxylic acid. A series of poly(amide imide imide)s (PAIIs) with inherent viscosities of 0.8–1.1 dL/g were prepared from tetraimide dicarboxylic acid with various aromatic diamines by direct polycondensation. Most of the PAIIs were readily soluble in a variety of amide polar solvents and even in less polar m‐cresol and pyridine. Solvent‐cast films had tensile strengths ranging from 99 to 106 MPa, elongations at break ranging from 8 to 13%, and initial moduli ranging from 2.0 to 2.3 GPa. The glass‐transition temperatures of these PAIIs were recorded at 244–276 °C. They had 10% weight losses at temperatures above 520 °C in air or nitrogen atmospheres. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1092–1102, 2002     

Broad-line NMR and dynamic mechanical behavior of some aromatic polyesters

The dynamic mechanical properties of four aromatic polyesters were measured at temperatures in the 78–540°K region at 10³–10⁴ cps. The polymers studied were: poly(1,3 phenylene isophthalate), poly(1,4 phenylene terephthalate), poly(4,4′ diphenylene isophthalate), and poly(4,4′ diphenylene terephthalate). All four polymers had β loss peaks at about 280°K. Distinct β^* mechanical processes were found for the two terephthalate esters. Broad-line nuclear magnetic resonance measurements were carried out in the 150–440°K temperature range on the four polyesters mentioned above in addition to poly(4,4′ diphenylene 4,4′ biphenyl dicarboxylate). A change in NMR second moment takes place in the 190–330°K region, the magnitude of which is dependent on the polymer structure. The results are compared with those found for a series of aromatic polyamides and are discussed in terms of possible motional processes.     

A novel non-dripping oligomeric flame retardant for polyethylene terephthalate

An oligomer or low polymer, polysulfonyldiphenylene thiophenylphosphonate (PSTPP), was synthesized from phenylphosphonothioic dichloride (PPTD) and 4,4^′-sulfonyldiphenol (SDP) by polycondensation reaction. Its structures and thermal behaviors were studied using infrared spectrophotometer and thermal gravimetric analysis, respectively. This novel oligomer can be used as the flame retardant for poly(ethylene terephthalate) (PET). PET samples containing PSTPP can reach an oxygen index (OI) of 29 and a UL-94 V-0 rating when the phosphorus content of the sample is 2.5 wt%. No melting dripping was observed during the UL-94 flame test.     

Phase separation in semicrystalline blends of poly(phenylene sulfide) and poly(ethylene terephthalate). I. Preparation of poly(phenylene sulfide)-graft-poly(ethylene terephthalate) copolymers by ester interchange and characterization utilizing the model compound 2,4-bis(phenylthio benzoic acid)

Blends of carboxyl functionalized poly(phenylene sulfide) (PPS) and poly(ethylene terephthalate) (PET) were shown to undergo an ester interchange reaction during melt blending. Pendent carboxyl functionality randomly incorporated along the PPS chain reacts with the ester moiety of PET to form a graft copolymer. A model compound, 2,4-bis(phenylthio benzoic acid), has been synthesized to assist in defining the level of carboxyl functionality on the PPS chain. Evidence of the grafting reaction has been gathered from infrared spectroscopy, solubility measurements, and electron microscopy. When added to blends of PPS and PET homopolymers, the graft copolymer significantly reduces the average domain size of the dispersed phase across the entire composition range. This study describes the role that graft copolymers formed by ester interchange reactions can play in compatibilizing this immiscible blend system, with particular focus on the conditions leading to increased grafting efficiency. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3473–3485, 1999     

Interval kinetic gravimetric sorption of acetone in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Interval sorption kinetics of acetone in solvent cast films of random poly(ethylene terephthalate)-co-(ethylene 2,6-naphthalate) (PET-co-PEN) are reported at 35°C and at acetone pressures ranging from 0 to 7.3 cm Hg. Polymer composition is varied systematically from 0% to 50% poly(ethylene 2,6-naphthalate). Equilibrium sorption is well described by the dual-mode sorption model. Interval sorption kinetics are described using a two-stage model that incorporates both Fickian diffusion and protracted polymer structural relaxation. The incorporation of low levels of PEN into PET significantly reduces the excess free volume associated with the glassy state and, for these interval acetone sorption experiments in ∼ 5 μm-thick films, decreases the fraction of acetone uptake controlled by penetrant-induced polymer structural relaxation. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2973–2984, 1999     

Free volume and oxygen transport in cold‐drawn polyesters

Poly(ethylene terephthalate) (PET), poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) (PETBB55), and poly(ethylene 2,6‐naphthalate) (PEN) were cold‐drawn to achieve uniform extension without crystallization or stress whitening, and oxygen transport properties were studied at temperatures from 10 to 40 °C. Correlation of oxygen solubility and polymer specific volume made it possible to consider the oriented polyester as a one‐phase densified glass. Orientation was viewed as decreasing the amount of excess‐hole free volume and bringing the nonequilibrium polymer glass closer to the equilibrium condition. Between 10 and 40 °C, the amount of excess‐hole free volume in PET decreased as the polymer approached the glass transition temperature. In contrast, temperature changes in this range had little effect on the excess‐hole free volume in PETBB55 and PEN, which were well below their glass transition temperature. Gas diffusion was viewed as discrete jumps of the oxygen molecule between holes of excess‐free volume. The jump length was extracted from the activation energy for diffusion according to a channel‐formation model. The result agreed well with the hole spacing estimated from a simple lattice model using the hole density reported in the literature. Extending the lattice model to estimate the mean excess‐free volume hole radius from the fractional free volume resulted in good correlation with the hole radius obtained from positron annihilation lifetime spectroscopy. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 493–504, 2004     

A new sequence isomer of AB‐polybenzimidazole for high‐temperature PEM fuel cells

A new sequence isomer of AB‐polybenzimidazole (AB‐PBI) was developed as a candidate for high‐temperature polymer electrolyte membrane fuel cells. A diacid monomer, 2,2′‐bisbenzimidazole‐5,5′‐dicarboxylic acid, was synthesized and polymerized with 3,3′,4,4′‐tetraaminobiphenyl to prepare a polymer that was composed of repeating 2,5‐benzimidazole units. In contrast to previously prepared AB‐PBI, which contains only head‐to‐tail benzimidazole sequences, the new polymer also contains head‐to‐head and tail‐to‐tail benzimidazole sequences. The polymer was prepared in polyphosphoric acid (PPA) and cast into membranes using the sol–gel PPA process. Membranes formed from the new AB‐PBI were found to be mechanically stronger, possessed higher acid doping levels, and showed improved fuel cell performance, when compared to the previously known AB‐PBI. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of polyimides based on new fluorinated 3,3′-diaminobiphenyls

Two new fluorinated diamine monomers, 3,3′-diamino-5,5′-bis(trifluoromethyl)biphenyl and 3,3′-diamino-6,6′-bis(trifluoromethoxy)biphenyl, as well as a known nonfluorinated analog, 3,3′-diaminobiphenyl, were synthesized. Reaction of these diamines with rigid, highly rod-like dianhydrides produced poly(amic acid)s and polyimides, which were spin coated and thermally treated to produce polyimide films for evaluation in electronics applications. It was hoped that these polyimide films would exhibit an ideal combination of low thermal expansion, reduced water absorption, and low dielectric constant but with improved elongation due to the “crankshaft” nature of the 3,3′-biphenyl unit. Unlike polyimide films from analogous 4,4′-diaminobiphenyls, however, the 3,3′-diaminobiphenyl-based polyimides did not yield low in-plane thermal expansion coefficient in spin-coated films. In some cases high elongation was achieved, but with high thermal expansion. These new diamines may nevertheless find utility in polyimides and polyaramides for membrane, fiber, and other applications. Additionally, they may be useful in modifying the properties of polymer backbones via copolymerization. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2441–2451, 1997     

Synthesis of a novel epoxy resin containing diphenylether moiety and thermal properties of its cured polymer with phenol novolac

A new type of epoxy resin containing 4,4′-diphenylether moiety in the backbone (2) was synthesized, and was confirmed by gel permeation chromatography, infrared spectroscopy, and ¹H nuclear magnetic resonance spectroscopy. In addition, in order to evaluate the influence of 4,4′-diphenylether moiety in the structure, epoxy resins having 4,4′-biphenylene moiety (4) and having 1,4-phenylene moiety (6) in place of 4,4′-diphenylether moiety were synthesized. The cured polymer obtained through the curing reaction between the new diphenylether-containing epoxy resin and phenol novolac was used for making a comparison of its thermal and physical properties with those obtained from 4, 6, and bisphenol-A (4,4′-isopropylidenediphenol) type epoxy resin. The cured polymer obtained from 2 showed markedly higher anaerobic char yield at 700°C of 44.0 wt %, higher fracture toughness, and higher mechanical strength and modulus. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3687–3693, 1999     

Synthesis and characterization of photocrosslinkable,side‐chain,second‐order nonlinear optical poly(ester imide)s with great film‐forming ability and long‐term dipole orientation stability

A series of photocrosslinkable, side‐chain, second‐order nonlinear optical (NLO) poly(ester imide)s (PEIs) based on a chromophore‐containing dianhydride, 2,2′‐{4‐[(4‐nitrophenyl)‐azo]phenyl}iminobis(ethyl benzene‐1,2‐dicarboxylic acid anhydride‐4‐carboxylate), benzophenone‐3,3′,4,4′‐tetracarboxylic dianhydride, and 4,4′‐diamino‐3,3′‐dimethyl diphenylmethane were prepared. The resulting PEIs exhibited many useful physical characteristics, such as good organosolubility, excellent film‐forming properties, high glass‐transition temperatures (186–229 °C), and high thermal decomposition temperatures. The electrooptic coefficient value of PEI3 at 650 nm was 11.5 pm/V, and high long‐term stability of the NLO chromophore alignment in the poled PEI3 film at 120 °C was observed. The temporal stability of the dipole orientation at 150 °C was further enhanced by ultraviolet irradiation because of photocrosslinking. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 303–312, 2003     

Thermotropic copolyamides from triethylene glycol bis(4-carboxyphenyl) ether and o-tolidine modified by kinking monomers

Copolymers of triethylene glycol bis(4-carboxyphenylether) (PEG₃), 4,4′-diamino-3,3′-dimethylbiphenyl (o-tolidine, OT), and several kinking comonomers of dicarboxylic acids and diamines were prepared to investigate which of the comonomers is more effective to lower melting points (T_ms) and clearing temperatures (T_is) of the resulting thermotropic copolyamides. In general, diamine modifiers were more effective than dicarboxylic acid ones even having the same chemical structures. All of diamines examined depressed their transition temperatures linearly with the modifier content whereas the dicarboxylic acid modifiers yielded copolymers having different profiles. m-Aminobenzoic acid, another type of comonomer producing the polyamide of the AB structure, was also examined. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 363–368, 1999