Electrically conductive composite prepared by template polymerization of pyrrole into a complexed polymer

Electrically conducting polymer composite films have been synthesized by the exposure of poly(4-vinylpyridine) complexed with cupric ions to pyrrole and water vapor. To immobilize a stoichiometric amount of the oxidant inside the polymer matrix, the ratio of poly(4-vinylpyridine)/cupric ion = 1.8 was chosen. Polypyrrole was formed in this tailored structure by a template polymerization process. Opaque polymer composite films with electrical conductivity up to 60 (Ω cm)^?1 have been obtained by this method, However, slightly colored transparent composite thin films with a conductivity as high as 50 (Ω cm)^?1 were also produced. The electrically conducting polymer composite films and the metal-polymer complex have been characterized by XPS and IR spectroscopy, elemental analysis, EDX, and scanning electron microscopy. The polymerization process was also followed by use of a quartz crystal microbalance. © 1994 John Wiley & Sons, Inc.     

Oxidative chemical polymerization of pyrrole

A reaction calorimeter has been used to determine at three different temperatures the enthalpy values for the polymerization of pyrrole dissolved in acetonitrile, by using FeCl₃ as the oxidative agent. From the calorimetric data it has been found that the reaction is first-order with respect to the pyrrole. The rate constants at the same temperatures have also been determined. By using the Arrhenius equation we have obtained the activation energy for the formation of this electroconducting polymer.Financial support from the italian National Research Council (CNR) is gratefully acknowledged.     

Electrochemically initiated chain polymerization of pyrrole in aqueous media

The electrochemical quartz crystal microbalance has been employed to investigate the electropolymerization of pyrrole in a variety of aqueous electrolytes. In contrast to the generally accepted cation–radical coupling process for the electropolymerization of pyrrole, an electrochemically initiated chain polymerization, featuring a high polymerization rate and involving little charge transport, was found under specific conditions in the presence of ClO^?₄, BF^?₄, and PF^?₆ electrolytes. The more typical cation-radical coupling mechanism, characterized by a constant polymerization charge to mass deposited ratio, is observed in the presence of Cl^?, NO^?₃, dodecyl sulfate, copper phthalocyanine tetrasulfonate, β-cyclodextrin tetradecasulfate, and poly(styrene sulfonate). Electrochemical characterizations of polypyrrole films prepared in aqueous ClO^?₄ electrolytes reveal that the polymer formed via chain polymerization exhibits the ability to transport both cations and anions during electrochemical switching between redox states, while the polymer synthesized through cation-radical coupling is only capable of transporting a single ionic species.     

Oxidative polymerization of pyrrole in polymer matrix

The oxidative matrix polymerization of pyrrole (Py) by Ce(IV) in the presence of Polyacrylic acid (PAA) has been studied to obtain water-soluble and insoluble products. The role of the PAA, Pyrrole, and Ce(IV) concentration, order of component addition, the structure of polymer matrix (PAA, Hydroxy Ethyl Cellulose (HES), Poly-N-vinylpyrrolidone (PVP)], and model unit of PAA (propionic acid), on the polymerization system were investigated. Interaction of PAA with insoluble polypyrrole (PPy) and the interpolymer complex formation were investigated along with the aggregation of PPy onto the matrix polymer followed by spectral shifts. FTIR results of insoluble products obtained from the PAA–Py–Ce(IV) system and solubility of the system is explained in light of the mechanism of the polymerization of pyrrole on the polymer matrix. © 1995 John Wiley & Sons, Inc.     

The calorimetric determination of the ceiling temperature for the chemical polymerization of pyrrole

The previously found strong dependence of the polymerization enthalpy on the reaction temperature has been rationalized. The temperature dependence is to be ascribed to the existence of a ‘ceiling temperature’ for the polymerization process of the pyrrole monomer. The determined ceiling temperature has beenT?350 K when FeCl₃ was used as the oxidizing agent in CH₃CN solution. The existence of a ceiling temperature together with its already determined exoenthalpic nature allows to classify the polymerization reaction as an exoentropic one. From the dependence of the yield of insoluble polymer on the reaction temperature, the trend of the relative mean numeral molecular massM _n for the different obtained polymers has been determined. Measurements of electrical conductivity on pressed pellets of the different polymers allowed to establish a correlation between theM _n value and the conductivities The dependence of the conductivity on the exposition time to the air allowed to do some essays on the aging behaviour of the obtained polypyrrole. By making some assumptions, an absolute calorimetric determination of the value ofM _n of polypyrrole was tempted together with that of the related poly-N-vinilpyrrole.     

Dispersion polymerization in polar solvents

The effect of the nitrogen purge, monomer purification, type of agitation, and presence of costabilizer on the particle size distribution (PSD) was investigated in the dispersion po-lymerization of styrene in ethanol and in the dispersion copolymerization of styrene and butyl acrylate in a water–ethanol mixture. Purging with nitrogen and, to a lesser extent, monomer purification, were of paramount importance to achieve monodispersity. The type of agitation had a week effect on the PSD, whereas the presence of costabilizer had no effect on the PSD. © 1995 John Wiley & Sons, Inc.     

Encapsulation of inorganic particles via miniemulsion polymerization. I. Dispersion of titanium dioxide particles in organic media using OLOA 370 as stabilizer

The dispersion of hydrophilic and hydrophobic titanium dioxide (TiO₂) particles in organic media (styrene and cyclohexane) was studied to evaluate the effect of dispersion quality (i.e., size and stability) on the encapsulation efficiencies of subsequent miniemulsion polymerizations. Through screening studies of various block copolymers, OLOA 370 (polybutene–succinimide pentamine) was chosen as the stabilizer for detailed dispersion studies on both types of TiO₂ particles. As a result of strong interactions between the amine end group of the OLOA 370 stabilizer and the hydroxyl groups on the surface of the hydrophilic TiO₂ particles, a good dispersion stability and small particle size (D_v = 39–45 nm) was obtained using 1.0 wt % stabilizer and 20 min of sonification. The dispersions of the hydrophobic TiO₂ particles resulted in a larger average particle size (D_v = 60 nm) and poorer stability. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4419–4430, 2000     

DC-plasma polymerization of pyrrole

DC-plasma-polymerized pyrrole (PP-Py) films deposited on metals were extensively characterized by Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS), Reflection-Absorption IR Spectroscopy (RAIR), X-ray Photoelectron Spectroscopy (XPS), Scanning Tunneling Microscopy (STM), Glow Discharge Optical Spectroscopy (GDOS), electrical conductivity (ASTM Franklin test), and contact angle measurements. TOF-SIMS and RAIR showed no spectroscopic evidence of the presence of the pyrrole ring structure in any of the plasmadeposited films. The major parameter that affected their composition was found to be the pressure. Films deposited at low pressure were less hydrogenated than those polymerized at high pressure or in remote plasma conditions. Although all deposits oxidized slowly in air, their surface energy remained low over an extended period of time. The electrical conductivity of the PP-Py films was in the range of 10⁻³–10⁻⁴ S/cm, i.e., higher than that of amorphous carbon films.     

Synthesis and characterization of polypyrrole/graphite oxide composite by in situ emulsion polymerization

This work demonstrates a feasible route to synthesize the layered polypyrrole/graphite oxide (PPy/GO) composite by in situ emulsion polymerization in the presence of cationic surfactant cetyltrimethylammonium bromide (CTAB) as emulsifier. AFM and XRD results reveal that the GO can be delaminated into nanosheets and well dispersed in aqueous solution in the presence of CTAB. The PPy nanowires are formed due to the presence of the lamellar mesostructured (CTA)₂S₂O₈ as a template. The results of the PPy/GO composite indicate the PPy insert successfully into GO interlayers, and the nanofiber‐like PPy are deposited onto the GO surface. Owing to π–π electron stacking effect between the pyrrole ring of PPy and the unoxided domain of GO sheets, the electrical conductivity of PPy/GO composite (5 S/cm) significantly improves in comparison with pure PPy nanowires (0.94 S/cm) and pristine GO (1 × 10^?6 S/cm). © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1329–1335, 2010     

Dispersion polymerization of methyl methacrylate: Mechanism of particle formation

The mechanism for the formation of micron-size polymer particles in the dispersion polymerization of methyl methacrylate was investigated by applying dynamic light scattering to monitor the evolution of the average particle size in the early stages of the polymerization. In addition, the contributions of physically adsorbed stabilizer and graft copolymer were evaluated by measuring the bound, unbound (adsorbed), and free stabilizer, and by determining the amount of added stabilizer required in seeded dispersion polymerizations. Twenty nanometer particles (termed nuclei) were the smallest particles detected and are considered to be formed by aggregation of growing polymer chains precipitating from solution as they exceed their critical chain length. Aggregation of these nuclei with themselves and their aggregates continues until mature and stable particles are formed. This occurs when sufficient stabilizer occupies the particle surface which includes both the polymeric stabilizer [poly(vinylpyrrolidone)] and its graft copolymer which is created in situ. The effects of process variables are discussed based on this mechanistic picture of the dispersion polymerization process. © 1994 John Wiley & Sons, Inc.     

在水溶液中电化学反应制备大面积聚吡咯膜

以不锈钢为电极,在吡咯水溶液中,经电化学聚合制备了大面积的聚吡咯薄膜。研究了反应电流密度、反应温度、对阴离子种类和浓度等因素对成膜性能及电导率的影响。选择合适的反应条件,可得到电导率为120Scm~(-1)、抗拉强度46MPA、模量为1.75GPA的聚吡咯膜。     

The inverse emulsion polymerization of acrylamide using polystyrene-graft-polyoxyethylene as the stabilizer

Inverse emulsion polymerization of aqueous solution of acrylamide (AM) in toluene is carried out using polystyrene-graft-polyoxyethylene (PSt-g-PEO) as an emulsifier. The kinetics of polymerization, morphology of the particle, and particle size of the inverse emulsion have been investigated. The rates of polymerization are found to be proportional to the initiator concentration, the monomer concentration, and the emulsifier concentration. The morphology of the particle shows a spherical structure. The effects of amphipathic graft copolymer structure on the average molecular weight of polyacrylamide are studied. The mechanism of the inverse emulsion polymerization using amphipathic graft copolymer as emulsifier is proposed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2719–2725, 1999     

Kinetic aspects of styrene minisuspension polymerization using a mixture PVA-SDS as stabilizer: Effect of the time of addition of SDS

The styrene minisuspension polymerization at 70 °C using AIBN as initiator and Polyvinil alcohol (PVA) and mixture PVA-sodium dodecil sulfate (SDS) as stabilizers was studied focusing on the kinetic behavior of the process after the SDS was added (PVA is present from the beginning and SDS is added at a given time t_SDS). It was confirmed that the addition of SDS to the system initially stabilized with PVA highly enhances the colloidal stability of the polymer particles because of the association formed between SDS and PVA molecules. It was observed that when SDS is added the rate of polymerization, the average molecular weight and final latex viscosity increase. The earlier the addition of SDS the more marked these increments. This behavior is explained in terms of the colloidal stability of the particles formed via emulsion polymerization and its effect on kinetic aspects such as the evolution of molecular weight and particle size distributions during the minisuspension polymerization.     

Nonaqueous dispersion polymerization of styrene in methanol with the ionomer block copolymer poly[(4‐methylstyrene)‐co‐(4‐vinyltriethylbenzyl ammonium bromide)]‐b‐polyisobutene as a stabilizer

The nonaqueous dispersion polymerization of styrene in methanol with poly[(4‐methylstyrene)‐co‐(4‐vinyltriethylbenzyl ammonium bromide)]‐b‐polyisobutene as a stabilizer was investigated. There was no observable inducing period or autoacceleration in the polymerization process. The conversion increased almost linearly with the polymerization time as high as 80%. The average sizes of the obtained polystyrene particles increased, and the size distributions of the polystyrene particles tended to become narrower, with increasing conversion. The mechanism of the dispersion polymerization in the presence of polyisobutene‐b‐poly[(4‐methylstyrene)‐co‐(4‐vinyltriethylbenzyl ammonium bromide)] was nucleation/growth. When the stabilizer/monomer ratio (w/w) was greater than 2.0%, the polystyrene dispersion was stable, and there was no observable polymer particle coagulation taking place during the whole polymerization process. The average diameter of the polymer particles can be mediated through changes in the polymerization conversion, monomer, and stabilizer. Nearly monodispersed polystyrene particles with average diameters of approximately 0.45–2.21 μm were obtained under optimal conditions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2678–2685, 2004     

Dispersion polymerization of styrene in alcohol media: Effect of initiator concentration,solvent polarity,and temperature on the rate of polymerization

The effects of three different variables (initiator concentration, polarity of the solvent and reaction temperature) on the rate of dispersion polymerization of styrene in alcohols have been investigated. It was found that the rate of polymerization increases with the initiator (AIBN) concentration at the 0% conversion level and becomes independent of it at higher monomer conversions. More significant was the result that the rate was also found to increase with solvent polarity. This is consistent with thermodynamic equilibrium calculations which account for the partitioning behavior of monomer and solvent in both the solution and the particle phases. The results further suggest the existence of two different kinetic regions: one at low conversions, where the reaction takes place primarily in the solution phase, and one at high conversions, where the reaction takes place primarily in the particle phase. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2907–2915, 1997     

Pickering miniemulsion polymerization using Laponite clay as a stabilizer

Solid-stabilized, or Pickering, miniemulsion polymerizations using Laponite clay discs as stabilizer are investigated. Free radical polymerizations are carried out using a variety of hydrophobic monomers (i.e., styrene, lauryl (meth)acrylate, butyl (meth)acrylate, octyl acrylate, and 2-ethyl hexyl acrylate). Armored latexes, of which the surfaces of the particles are covered with clay discs, are obtained, as confirmed by scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM). Overall polymerization kinetics of the Pickering miniemulsion polymerizations of styrene were investigated via gravimetry. Comparison with the bulk polymerization analogue clearly shows compartmentalization. Moreover, retardation effects up to intermediate monomer conversions are observed; they are more prominent for the smaller particles and are ascribed to the Laponite clay. A model is presented that allows for the prediction of the average particle size of the latexes produced as a function of the amounts of monomer and Pickering stabilizers used. It shows that under specific generic conditions the number of clay discs used correlates in a linear fashion with the total surface area of the latex particles. This is a direct result of the reversibility of the Laponite clay disc adhesion process under the emulsification conditions (i.e., sonication) used.     

In situ intercalative polymerization of conducting polypyrrole/montmorillonite nanocomposites

Conducting polypyrrole (PPy)‐montmorillonite (MMT) clay nanocomposites have been synthesized by the in situ intercalative polymerization method. The PPy‐MMT nanocomposites are characterized by field‐emission scanning electron microscopy (FE‐SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), ultraviolet–visible (UV–vis) spectroscopy, thermogravimetric analysis (TGA), and Fourier‐transform infrared (FTIR) spectroscopy. XRD patterns show that after polymerization by the in situ intercalative method with ammonium persulfate and 1 M HCl, an increase in the basal spacing from 1.2 to 1.9 nm was observed, signifying that PPy is synthesized between the interlayer spaces of MMT. TEM and SEM micrographs suggest that the coexistence of intercalated MMT layers with the PPy macromolecules. FTIR reveals that there might be possible interfacial interactions present between the MMT clay and PPy matrix. The study also shows that the introduction of MMT clay results in thermal stability improvement of the PPy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2279–2285, 2008