Development of oriented structure and properties on drawing of poly(vinylidene fluoride) by solid‐state coextrusion

Gel films of poly(vinylidene fluoride) (PVDF) consisting of α‐form crystals were drawn uniaxially by solid‐state coextrusion to extrusion draw ratios (EDR) up to 9 at an optimum extrusion temperature of 160 °C, about 10°C below the melting temperature (T_m). The development of an oriented structure and mechanical and electrical properties on coextrusion drawing were studied as a function of EDR. Wide‐angle X‐ray diffraction patterns showed that the α crystals in the original gel films were progressively transformed into oriented β‐form crystals with increasing EDR. At the highest EDR of 9 achieved, the drawn product consisted of a highly oriented fibrous morphology with only β crystals even for the draw near the T_m. The dynamic Young's modulus along the draw direction also increased with EDR up to 10.5 GPa at the maximum EDR of 9. The electrical properties of ferroelectricity and piezoelectricity were also markedly enhanced on solid‐state coextrusion. The D–E square hysteresis loop became significantly sharper with EDR, and a remanent polarization P_r of 100 mC/m² and electromechanical coupling factor along the thickness direction k_t of 0.27 were achieved at the maximum EDR of 9. The crystallinity value of 73–80% for the EDR 9 film, estimated from these electrical properties, compares well with that calculated by the ratio of the crystallite size along the chain axis to the meridional small‐angle X‐ray scattering (SAXS) long period, showing the average thickness of the lamellae within the drawn β film. These results, as well as the appearance of a strong SAXS maximum, suggest that the oriented structure and properties of the β‐PVDF are better explained in terms of a crystal/amorphous series arrangement along the draw axis. Further, the mechanical and electrical properties obtained in this work are the highest among those ever reported for a β‐PVDF, and the latter approaches those observed for the vinylidene fluoride and trifluoroethylene copolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1371–1380, 2001     

Effect of annealing on the structure and properties of poly(vinylidene fluoride) β‐form films

Oriented poly(vinylidene fluoride) (PVDF) films consisting of β crystals were prepared by the solid‐state coextrusion (SC) of a gel film near the melting temperature (T_m) and by conventional cold tensile drawing (TD) of a melt‐quenched film. These films were annealed over the temperature range of 75–190 °C (below and above the static T_m) while the sample length was kept constant or constant loads were applied. After annealing with the sample length kept constant, the dynamic Young's modulus markedly decreased because of the relaxation of oriented amorphous chains, as shown by infrared spectroscopy. In contrast, annealing under a constant load improved the chain orientation in both the crystalline and amorphous regions, resulting in an increase in the modulus from an initial 10.5 to 14.3 GPa for the SC and from an initial 3.3 to 4.8 GPa for the TD. The SC, annealed at 190 °C with a constant load corresponding to an initial tension of 200 MPa, exhibited an extreme crystalline‐chain orientation of 0.998 and a modulus of 14.3 GPa, among the highest values ever reported for PVDF. Although the remanent polarization (P_r) of the TD increased slightly from the initial 62 to 68 mC/m², P_r of the SC stayed constant at 100 mC/m² independently of the annealing conditions. This suggests that the P_r value of 100 mC/m² approached the equilibrium value for this PVDF sample containing 3.5 mol % structural defects. Therefore, although the modulus and P_r of the TD increased slightly with annealing, the maximum values achieved by annealing were markedly lower than those of the SC and annealed SC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1701–1712, 2003     

Crystal forms and ferroelectric properties of poly(vinylidene fluoride)/polyamide 11 blends prepared by high‐shear processing

Nanostructured poly(vinylidene fluoride) (PVDF)/polyamide 11 (PA11) blends have been melt‐processed using a high‐shear extruder. Uniaxially oriented blended films were fabricated by hot rolling to prepare ferroelectic films. The effects of rolling temperature and draw ratio on the crystal forms of both PVDF and PA 11 were investigated by means of Fourier transform infrared spectra (FTIR) and wide‐angle X‐ray diffraction (WAXD). It was shown that hot rolling in the range of 25–110 °C results in the crystal form transformation from the nonpolar α‐form into the polar β‐form for PVDF. The content and orientation function of β‐crystallites are strongly dependent upon the rolling temperature and the draw ratio. The highest content of well‐oriented β‐crystallites was achieved with a draw ratio of 4.0 upon rolling at 80 °C. At the same time, the content of the α‐form of PA11 in the blend was also found to decrease by hot rolling. The ferroelectric properties (D‐E hysteresis) of the oriented blended films were measured. The remanent polarization of the PVDF/PA11 = 90/10 blend is as high as 91 mC/m², which is about 1.2 times higher than that of pure PVDF. The D‐E hysteresis curves and the temperature dependence of the piezoelectric stress coefficients of the high‐shear‐processed sample suggested that the formation of nano‐dispersed structures resulted in the improvement of the remanent polarization and thermal characteristics at a temperature higher than 80 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2707–2714, 2007     

Phase transformation and enhancement of toughness in polyvinylidene fluoride by onium salts

We study the effect of onium salts (benzyl triphenyl phosphonium chloride, BTPC; tetrabutyl ammonium perchlorate, TAP) on the crystallization of polyvinylidene fluoride (PVDF) from a melt. The β phase of PVDF crystals is polar and has excellent piezoelectric properties, in contrast to the nonpolar α phase. Processing of PVDF results in the formation of predominantly α‐phase crystals. Different amounts of the onium salts were melt‐mixed into PVDF using a micro‐compounder. PVDF containing about 0.5 wt % of BTPC is found to have predominantly β‐phase crystals in compression molded PVDF films, with an increase in the melting temperature by about 7 °C. A significant increase in the toughness of PVDF is obtained by the addition of BTPC. Polarizing microscopy indicates that the onium salts act as nucleating agents and result in significant reduction in spherulite size. Similar results were observed for samples prepared with TAP. The results of the study indicate a facile method for producing β‐phase PVDF films. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1339–1344, 2011     

Superdrawing of polytetrafluoroethylene nascent powder by solid‐state coextrusion

A film of nascent powder of polytetrafluoroethylene (PTFE), compacted below the ambient melting temperature (T_m, 335 °C), was drawn by two‐stage draw techniques consisting of a first‐stage solid‐state coextrusion followed by a second‐stage solid‐state coextrusion or tensile draw. Although the ductility of extrudates was lost for the second‐stage tensile draw at temperatures above 150 °C due to the rapid decrease in strength, as previously reported, the ductility of extrudates increased with temperature even above 150 °C when the second‐stage draw was made by solid‐state coextrusion, reflecting the different deformation flow fields in a free space for the former and in an extrusion die for the latter. Thus, a powder film initially coextruded to a low extrusion draw ratio (EDR) of 6–20 at 325 °C was further drawn by coextrusion to EDRs up to ～?400 at 325–340 °C, near the T_m. Extremely high chain orientation (f_c = 0.998 ± 0.001), crystallinity (96.5 ± 0.5)%, and tensile modulus (115 ± 5 GPa at 24 °C, corresponding to 73% of the X‐ray crystal modulus) were achieved at high EDRs. Despite such a morphological perfection and a high modulus, the tensile strength of a superdrawn tape, 0.48 ± 0.03 GPa, was significantly low when compared with those (1.4–2.3 GPa) previously reported by tensile drawing above the T_m. Such a low strength of a superdrawn, high‐modulus PTFE tape was ascribed to the low intermolecular interaction of PTFE and the lack of intercrystalline links along the fiber axis, reflecting the initial chain‐extended morphology of the nascent powder combined with the fairly high chain mobility associated with the crystal/crystal transitions at around room temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3369–3377, 2006     

Morphology,crystalline structure,and properties of poly(vinylidene fluoride)/silica hybrid composites

Poly(vinylidene fluoride)/silica (PVDF/SiO₂) hybrid composite films were prepared via sol–gel reactions from mixtures of PVDF and tetraethoxysilane in dimethylacetamide. Their morphology, crystalline structure, and thermal, mechanical, and electrical properties were examined. For morphology measurements, scanning electron microscopy and optical microscopy were applied. X‐ray diffraction and infrared analyses showed that the crystalline structure of PVDF was not changed much by the addition of SiO₂, indicating that there was no interaction between PVDF and SiO₂. With increasing SiO₂ content, the melting temperature rarely changed, the degree of crystallinity and the dielectric constant decreased, and the decomposition temperature slightly increased. A PVDF/SiO₂ hybrid composite film with 5 wt % SiO₂ exhibited balanced mechanical properties without a severe change in the crystalline structure of PVDF, whereas for the hybrid composites with higher SiO₂ contents (>10 wt %), the mechanical properties were reduced, and the spherulite texture of PVDF was significantly disrupted by the presence of SiO₂ particles. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 19–30, 2002     

Conformational changes and phase transformation mechanisms in PVDF solution‐cast films

The supramolecular crystal structure in poly(vinylidene fluoride) (PVDF) solution‐cast films is studied through changing crystallization conditions in two solvents of different structures and polarities. The crystalline‐state chain conformations of isothermally solution‐crystallized PVDF in N, N‐dimethylacetamide (DMAc), and cyclohexanone are studied through the specific FTIR absorption bands of α, β, and γ phase crystals. There are no changes in the FTIR spectra of cyclohexanone solution‐crystallized films in the temperature range of 50–120 °C. In the case of DMAc solution‐crystallized films, low temperature crystallization mainly results in formation of trans states (β and γ phases), whereas at higher temperatures gauche states become more populated (α phase). This is due to the variations in solvent polarity and ability to induce a specific conformation in PVDF chains, through the changes in chain coil dimensions. This indicates that in spite of cyclohexanone solutions, the intermolecular interactions between PVDF and DMAc are temperature‐sensitive and more important in stabilizing conformations of PVDF in crystalline phase than temperature dependence of PVDF chain end‐to‐end distance <r²>. The high‐resolution ¹⁹F NMR spectroscopy also showed little displacement in PVDF characteristic chemical shifts probably due to changes in PVDF chain conformation resulting from temperature variations. Upon uniaxial stretching of the prepared films under certain conditions, contribution of trans state becomes more prominent, especially for the originally higher α phase‐containing films. Due to formation of some kink bands during film stretching and phase transformation, α phase absorption bands are still present in infrared spectra. Besides, uniaxial stretching greatly enhances piezoelectric properties of the films, maybe due to formation of oriented β phase crystals, which are of more uniform distribution of dipole moments. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3487–3495, 2004     

Preferential formation of electroactive crystalline phases in poly(vinylidene fluoride)/organically modified silicate nanocomposites

The role of organically modified silicate (OMS), Lucentite STN on the formation of β‐crystalline phase of poly(vinylidene fluoride) (PVDF) is investigated in the present study. The OMS was solution blended with PVDF and cast on glass slide to form PVDF‐OMS nanocomposites. Solution cast samples were subjected to various thermal treatments including annealing (AC‐AN), melt‐quenching followed by annealing (MQ‐AN), and melt‐slow cooling (MSC). Fourier‐transform infrared spectroscopy (FT‐IR), wide angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC) were used to investigate the crystalline structure of thermally treated samples. As a special effort, the combination of in situ thermal FT‐IR, WAXD, and DSC studies was utilized to clearly assess the thermal properties. FT‐IR and WAXD results of MQ‐AN samples revealed the presence of β‐phase of PVDF. Ion‐dipole interaction between the exfoliated clay nanolayers and PVDF was considered as a main factor for the formation of β‐phase. Melt‐crystallization temperature and subsequent melting point were enhanced by the addition of OMS. Solid β‐ to γ‐crystal phase transition was observed from in situ FT‐IR and WAXD curves when the representative MQ‐AN sample was subjected to thermal scanning. Upon heating, β‐phase was found to disappear through transformation to the thermodynamically stable γ‐phase rather than melting directly. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2173–2187, 2008     

Ferroelectric poly(vinylidene fluoride) PVDF films derived from the solutions with retainable water and controlled water loss

To obtain β‐phase dominant ferroelectric poly(vinylidene fluoride) (PVDF) homopolymer thin films on aluminum‐coated silicon substrates, the retaining and loss of water were manipulated by introducing several hydrated and hygroscopic chemicals in the precursor solutions, including aluminum nitrate nonahydrate, aluminum chloride hexahydrate, chromium nitrate nonahydrate, tetra‐n‐butylammonium chloride, and one hygroscopic but nonhydrated chemical, ammonium acetate. Their ability of retaining water during the thermal annealing of the films and the relationship between water retaining and the effects on promoting the β phase were investigated. The results showed an ideal scenario was that the added hydrated salts should be able to retain substantial amount of water during the PVDF crystallization to effectively promote the β phase but completely dehydrate or decompose at the further elevated annealing temperature in order to obtain β‐phase dominant PVDF film without substantially incorporating water and deteriorating the electrical properties. As one of the hydrated chemicals well satisfying the above requirements, Al(NO₃)₃·9H₂O, of different amounts was introduced to the PVDF precursor solutions and the optimal resulting β‐phase dominant ferroelectric PVDF thin films exhibited smooth morphology, low dielectric loss, high remnant polarization of 89 mC/m², and large effective piezoelectric coefficient d₃₃ of ?14.5 pm/V (under the clamping of the substrate). © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2410–2418, 2009     

Controlled melting of individual,nano‐meter‐sized,polymer crystals confined in a block copolymer mesostructure

We demonstrate a possibility to create custom‐made surface patterns on multiple length scales by melting selected nano‐meter‐sized polymer crystals confined in a highly ordered, spherical mesostructure of a hydrogenated poly(butadiene‐block‐ethylene oxide) (PB_h‐b‐PEO) block copolymer. With heatable probes of an atomic force microscope as a heat source, we succeeded to provide highly locally the thermal energy necessary to individually melt such crystals. Besides this possibility for modification of surface properties, we performed detailed in situ studies of thermally induced reorganization processes and subsequent melting of polymer crystals in confined volumes of a block copolymer mesostructure. Close to the melting point, the stability of the confined crystals could be improved by annealing. In addition, the crystal size increased at the expense of already‐molten crystals, indicating diffusion of PEO blocks across the highly incompatible PB_h matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1312–1320, 2004     

Oriented crystallization of poly(L‐lactic acid) in uniaxially oriented blends with poly(vinylidene fluoride)

This article describes the oriented crystallization of poly(L ‐lactic acid) (PLLA) in uniaxially oriented blends with poly(vinylidene fluoride) (PVDF). Uniaxially drawn films of PLLA/PVDF blend with fixed ends were heat‐treated in two ways to crystallize PLLA in oriented blend films. The crystal orientation of PLLA depended upon the heat‐treatment process. The crystal c‐axis of the α form crystal of PLLA was highly oriented in the drawing direction in a sample cold‐crystallized at T_c = 120 °C, whereas the tilt‐orientation of the [200]/ [110] axes of PLLA was induced in the sample crystallized at T_c = 120 °C after preheating at T_p = 164.5–168.5 °C. Detailed analysis of the wide‐angle X‐ray diffraction (WAXD) indicated that the [020]/ [310] crystal axes were oriented parallel to the drawing direction, which causes the tilt‐orientation of the [200]/ [110] axes and other crystal axes. Scanning electron microscopy (SEM) suggested that oriented crystallization occurs in the stretched domains of PLLA with diameters of 0.5–2.0 μm in the uniaxially drawn films of PVDF/PLLA = 90/10 blend. Although the mechanism for the oriented crystallization of PLLA was not clear, a possibility was heteroepitaxy of the [200]/[110] axes of the α form crystal of PLLA along the [201]/[111] axes of the β form crystal of PVDF that is induced by lattice matching of d₁₀₀(PLLA) ≈ 5d₂₀₁(PVDF). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1376–1389, 2008     

Superdrawing of polytetrafluoroethylene virgin powder above the static melting temperature

A new two‐stage draw technique was successfully applied to the superdrawing of polytetrafluoroethylene (PTFE) virgin powder. A film, compression‐molded from powder below the melting temperature (T_m = 335 °C), was initially solid‐state coextruded to an extrusion draw ratio (EDR) of 6–20 at 325 °C, about 10 °C below the T_m. These extrudates from the first‐stage draw were further drawn by a second‐stage pin draw in the temperature (T_d) range of 300–370 °C that covers the static T_m. The maximum achievable total draw ratio was ～60 at a T_d = 300 °C and increased rapidly with increasing T_d, reaching a maximum of 100–160 at a temperature window between 340 and 360 °C, depending on the initial EDRs. At yet higher T_d's, the ductility was lost as a result of melting. The high ductility of the PTFE extrudates at such high temperatures was ascribed to the improvement of interfacial adhesion and bonding between the deformed powder particles upon the first‐stage extrusion combined with the rapid heating of only a portion of the extrudate followed by the elongation at a high rate. The highly drawn fibers were highly crystalline (χ_c ≤ 87%) and showed high chain orientation (f_c ≤ 0.997) and a large crystallite size along the chain axis (D₀₀₁₅ ≤ 160 nm). The molecular draw ratio, estimated from the entropic shrinkage above the T_m, was close to the macroscopic deformation ratio independently of the initial EDRs. These results indicate that the draw was highly efficient in terms of chain extension, orientation, and crystallization. Thus, the maximum tensile modulus and strength achieved in this work were 102 ± 5 and 1.4 ± 0.2 GPa, respectively, at 24 °C. These tensile properties are among the highest ever reported on oriented PTFE. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1995–2004, 2001     

Computational analysis of bending strain in single chains of β‐PVDF

Hartree–Fock calculations on 20 carbon atom chains of β‐phase poly(vinylidene fluoride) (PVDF) were done as a function of bending strain. The results can be modeled in terms of a classical energy versus strain curve resulting in a pseudomodulus (310 GPa) comparable to the Young's modulus calculated for stretching along carbon atom chain (199 GPa). The model also shows that the minimum energy state of a single chain of the polymer is not linear in the all‐trans geometry and that a significant strain energy is stored in natural thin films. This suggests that energy can be captured from bending motions in β‐PVDF. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1493–1495, 2011     

Evaluation of piezoelectric poly(vinylidene fluoride) polymers for use in space environments. I. Temperature limitations

Smart materials, such as thin‐film piezoelectric polymers, are interesting for potential applications on Gossamer spacecraft. This investigation aims to predict the performance and long‐term stability of the piezoelectric properties of poly(vinylidene fluoride) (PVDF) and its copolymers under conditions simulating the low‐Earth‐orbit environment. To examine the effects of temperature on the piezoelectric properties of PVDF, poly(vinylidenefluoride‐co‐trifluoroethylene), and poly(vinylidenefluoride‐co‐hexafluoropropylene), the d₃₃ piezoelectric coefficients were measured up to 160 °C, and the electric displacement/electric field (D–E) hysteresis loops were measured from ?80 to +110 °C. The room‐temperature d₃₃ coefficient of PVDF homopolymer films, annealed at 50, 80, and 125 °C, dropped rapidly within a few days of thermal exposure and then remained unchanged. In contrast, the TrFE copolymer exhibited greater thermal stability than the homopolymer, with d₃₃ remaining almost unchanged up to 125 °C. The HFP copolymer exhibited poor retention of d₃₃ at temperatures above 80 °C. In situ D–E loop measurements from ?80 to +110 °C showed that the remanent polarization of the TrFE copolymer was more stable than that of the PVDF homopolymer. D–E hysteresis loop and d₃₃ results were also compared with the deflection of the PVDF homopolymer and TrFE copolymer bimorphs tested over a wide temperature range. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1310‐1320, 2005     

Crystal Transformation and Development of Tensile Properties upon Drawing of Poly(L-lactic acid) by Solid-State Coextrusion: Effects of Molecular Weight

Melt-crystallized films of poly(L -lactic acid) (PLLA) with M_v in the range of 3.8 ∼ 46 × 10⁴ consisting of α-form crystals were uniaxially drawn by solid-state coextrusion. The effects of M_v, extrusion draw ratio (EDR), and extrusion temperature (T_ext) on the crystal/crystal transformation from α- to β-form crystals and the resultant tensile properties of drawn products were studied. The crystal transformation proceeded with EDR and more rapidly for the higher M_v's. Furthermore, the crystal transformation proceeded most rapidly with EDR at a T_ext around 130 °C, independently of the M_v's. As a result of the optimum combination of processing variables influencing the the crystal transformation (M_v, T_ext, and drawability), highly oriented films consisting of β-form crystals alone were obtained by coextrusion of higher M_v samples at T_ext's slightly below the melting temperature (150 ∼ 170 °C) and at higher EDR's > 11. Both the tensile modulus and strength increased rapidly with EDR. The modulus at a given EDR was slightly higher for the samples with higher M_v's. In contrast, the strength at a given EDR was remarkably higher for the higher M _v's. The highest tensile modulus of 8.0 GPa and strength of 500 MPa were obtained with the sample of the highest M_v of 46 × 10⁴ coextruded at 170 °C to the highest EDR of 14.     

Thin poly(ionic liquid) and poly(vinylidene fluoride) blend films with ferro‐ and piezo‐electric polar γ‐crystals

Ferro‐ and piezo‐electric poly(vinylidene fluoride) (PVDF) thin film is reported to be obtained by using a poly(ionic liquid) (PIL) [poly(2‐(dimethylamino)ethyl methacrylate) methyl chloride quaternary salt] through solution route. The short range interactions between localized cationic ions of PIL and polar >CF₂ of PVDF are responsible for modified polar γ‐PVDF (T₃GT₃Ḡ) formation. Modification in chain conformation of PVDF is confirmed by FTIR, XRD, and DSC studies suggesting the miscible PVDF–PIL (PPIL) blend. Up to 40 wt % loading of PIL in PVDF matrix enhances relative intensity of γ‐phase up to 50% in the entire crystalline phase. The P‐E hysteresis loop of PVDF‐PIL blends at 25 wt % PIL loading (PPIL‐25) thin film at sweep voltage of ±50 V shows excellent ferroelectric property with nearly saturated high remnant polarization ∼6.0 µC cm⁻² owing to large proportion of γ‐PVDF. However, non‐polar pure PVDF thin film shows unsaturated hysteresis loop with 1.4 µC cm⁻² remnant polarization. The operation voltage decreases effectively because of the polar γ‐phase formation in PPIL blended film. High‐sensitivity piezo‐response force microscopy shows electromechanical switching property at low voltages in PPIL‐25 thin films through local switching measurements, making them potentially suitable as ferroelectric tunnel barriers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 795–802     

Preparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion

Melt‐crystallized, low molecular weight poly(L ‐lactic acid) (PLLA) consisting of α crystals was uniaxially drawn by solid‐state extrusion at an extrusion temperature (T_ext) of 130–170 °C. A series of extrusion‐drawn samples were prepared at an optimum T_ext value of 170 °C, slightly below the melting temperature (T_m) of α crystals (～180 °C). The drawn products were characterized by deformation flow profiles, differential scanning calorimetry (DSC) melting thermograms, wide‐angle X‐ray scattering (WAXD), and small‐angle X‐ray scattering as a function of the extrusion draw ratio (EDR). The deformation mode in the solid‐state extrusion of semicrystalline PLLA was more variable and complex than that in the extensional deformation expected in tensile drawing, which generally gave a mixture of α and β crystals. The deformation profile was extensional at a low EDR and transformed to a parabolic shear pattern at a higher EDR. At a given EDR, the central portion of an extrudate showed extensional deformation and the shear component became progressively more significant, moving from the center to the surface region. The WAXD intensities of the (0010)_α and (003)_β reflections on the meridian as well as the DSC melting thermograms showed that the crystal transformation from the initial α form to the oriented β form proceeded rapidly with increasing EDR at an EDR greater than 4. Furthermore, WAXD showed that the crystal transformation proceeded slightly more rapidly at the sheath region than at the core region. This fact, combined with the deformation profiles (shear at the sheath and extensional at the core), indicated that the crystal transformation was promoted by shear deformation under a high pressure rather than by extensional deformation. Thus, a highly oriented rod consisting of only β crystals was obtained by solid‐state extrusion of melt‐crystallized, low molecular weight PLLA slightly below T_m. The structure and properties of the α‐ and β‐form crystals were also studied. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 95–104, 2002     

Mechanical property and biodegradability of solution‐cast films prepared from amphiphilic polylactide‐grafted dextran

Polylactide (PLA)‐grafted dextran was synthesized with a trimethylsilyl protection method to produce novel biodegradable, biomedical materials. PLA‐grafted dextrans with various lengths and numbers of graft chains were synthesized. The properties of solution‐cast films prepared from PLA‐grafted dextrans were investigated with thermal and dynamic mechanical analyses. The graft‐copolymer films exhibited lower glass‐transition temperatures, melting temperatures (T_m's), and crystallinities as well as higher viscosity properties as compared with poly‐L ‐lactide film. The T_m and crystallinity and mechanical properties at 37 °C could be adjusted by controlling the molecular structure such as the lengths and numbers of graft chains. Furthermore, the biodegradability of PLA‐grafted dextran films was investigated through the weight change of film and the molecular weight change of polymer during the in vitro degradation test. PLA‐grafted dextrans exhibited different degradation behavior from poly‐L ‐lactide with the introduction of a polysaccharide segment and branched structure as well as the change of end‐functional group. The degradation rate of PLA‐grafted dextran and the cast film prepared from PLA‐grafted dextran could be adjusted by controlling the sugar content or the length of graft chains. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2462–2468, 2003     

Synthesis and properties of thermoplastic polyimides with ether and ketone moieties

A series of polyimides containing ether and ketone moieties were synthesized from 1,3‐bis(4‐fluorobenzoyl) benzene and several commercially available dianhydrides via a conventional two‐step polymerization. The inherent viscosities of Polyamide acids ranged from 0.46 to 0.73 dL/g. Thermal properties, mechanical properties, and thermalplasticity of the obtained polimide films were investigated by focusing on the chemical structures of their repeat units. These films were amorphous, flexible, and transparent. All films displayed low T_gs (184–225 °C) but also excellent thermal stability, the 5% weight loss temperature was up to 542 °C under nitrogen. The films showed outstanding mechanical properties with the modulus up to 3.0 GPa and the elongation at break in the range of 8–160%. The uniaxial stretching of PI‐a at high temperature was studied owing to its excellent flexibility. The PI‐a had an elongation at break up to 1600% at 245 °C and the uniaxially stretched film exhibited a much higher modulus (3.9 GPa) and strength (240 MPa) than undrawn film. The results indicated that PI‐a can potentially be used to prepare materials such as fiber, ultra‐thin film or ultra‐high modulus film. All the obtained films also demonstrated excellent thermoplasticity (drop of E′ at T_g > 10³) which made the polyimides more suitable for melt processing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2878–2884, 2010     

Physical and dielectric properties of poly(vinylidene fluoride)/polybenzimidazole functionalized graphene nanocomposites

Polymer‐based nanocomposites with good dielectric behavior have engrossed research devotion because of their distinctive benefits in electronic applications. An in situ synthetic process for the polybenzimidazole functionalized graphene oxide (GBI) and its nanocomposite with poly(vinylidene fluoride) (PVDF) is described. GBI shows good dispersion in the bulk PVDF matrix implying a strong interaction of polybenzimidazole with PVDF as evident from morphological and FTIR studies. A gradual increment of GBI in PVDF increases its piezoelectric β‐polymorph formation with a maximum of 73% for 10 wt % GBI in PVDF (GBF10) which also exhibits highest thermal stability. An exhaustive study of frequency dependent electrical properties of GBF10 indicates significantly higher dielectric constant (61), low dielectric loss (0.42), and low AC conductivity value of 1.17 × 10^?10 S/cm at 100 Hz which are the key properties of a suitable capacitor. GBF10 also shows hydrophobic behavior (water uptake 2.89%) and low swelling ratio (1.143), providing an opportunity to use the composite film in fuel cell application. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 189–201