Transport properties of anion exchange membranes prepared by the reaction of crosslinked membranes having chloromethyl groups with 4‐vinylpyridine and trimethylamine

The electrodialytic transport properties of new anion exchange membranes were evaluated that included the transport numbers of various anions, sulfate, bromide, fluoride, and nitrate ions, relative to chloride ions and current efficiency. The anion exchange membranes were prepared by the reaction of copolymer membranes crosslinked to different extents having chloromethyl groups with 4‐vinylpyridine to form a ladder‐like polymer in the membranes and then with trimethylamine to convert the remaining chloromethyl groups to benzyl trimethylammonium groups. The transport numbers of the sulfate and fluoride ions relative to the chloride ions were markedly less for the membranes that had been reacted with 4‐vinylpyridine and then with trimethylamine compared with those of the membranes that had been reacted only with trimethylamine. On the other hand, the selective permeation of nitrate and bromide ions through the membranes was enhanced by the reaction with 4‐vinylpyridine although the membranes became tighter by the reaction. The decrease in permeation of the sulfate ions was attributed to a synergistic effect involving the decrease in sulfate ions ion‐exchanged with the membranes and the decrease in mobility of the sulfate ions in the membranes with a low degree of crosslinking. Though the ion‐exchanged sulfate ion content was the lowest in the highly crosslinked membranes, the mobility ratio between the sulfate ions and chloride ions did not decrease in the membranes. However, the increase in the permeation of nitrate ions was based on the increase in the ion‐exchanged amount of nitrate ions with the membrane, and not the change in the mobility ratio between the nitrate and chloride ions. The formation of the ladder‐like polymer in the membrane matrix brought on a decrease in the hydrophilicity of the membranes due to pyridine groups and an increase in their tightness. The current efficiency of all membranes was greater than 99% during the electrodialysis of 0.50 N salt solutions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1773–1785, 1999     

Permselectivity between two anions in anion exchange membranes crosslinked with various diamines in electrodialysis

A membranous copolymer crosslinked with divinylbenzene reacted with N,N,N′,N′-tetra-methylethylenediamine, N,N,N′,N′-tetramethyl-1,3-propanediamine, and N,N,N′,N′-tetramethyl-1,6-hexanediamine to prepare highly crosslinked anion exchange membranes. More than 80% of both tertiary amino groups of the diamines reacted with chloromethyl groups of the membrane to form crosslinkage. After formation of the high crosslinkage of the membrane was confirmed with dialysis of a neutral molecule, electrochemical properties of the obtained membranes (mainly, relative transport number between two anions in electrodialysis) were evaluated: nitrate ions to chloride ions, sulfate ions to chloride ions, fluoride ions to chloride ions, and bromide ions to chloride ions. Though larger anions, in general, were difficult to permeate through the membranes due to high crosslinkage, the number of methylene groups of the diamines (which means the increase in hydrophobicity of anion exchange groups) also affected the relative transport number between two anions. The lower the hydration of anions, the higher the relative transport number of the anions through the membranes with the hydrophobic anion exchange groups. © 1996 John Wiley & Sons, Inc.     

Preparation and properties of anion exchange membranes having pyridinium or pyridinium derivatives as anion exchange groups

Anion exchange membranes with pyridinum groups and various pyridinium derivative groups were prepared from a copolymer membrane composed of chloromethylstyrene and divinylbenzene, and pyridine and pyridine derivatives. The anion exchange membranes obtained showed excellent electrochemical properties in electrodialysis. The transport numbers of sulfate ions, bromide ions, nitrate ions, and fluoride ions relative to chloride ions were evaluated in connection with the species of a substituent and the position of the substituent in the pyridinium groups. In general, when a hydrophilic substituent (methanol groups) existed at the 2-position of the pyridinium groups, nitrate ions and bromide ions, which are less hydrated, permeated through the membranes with difficulty, and sulfate ions permeated selectively through the membranes. On the other hand, when hydrophobic groups, for example, ethyl groups, existed at the 2-position of the pyridinium groups, bromide ions and nitrate ionspermeated selectively through the membranes and fluoride ions had difficulty permeating through the membranes. The carbon number of the alkyl chain of 4-alkyl pyridinium groups also affected permeation of nitrate ions and bromide ions due to the change in hydrophilicity of the membranes. Though the hydration of the anions and the species of the substituent at the 2-position of the pyridinium groups were related to selective permeation of the anion through the membranes, permeation of sulfate ions was not as sensitive to the hydrophilicity of the membranes. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 49–58, 1998     

Recent development of temperature‐responsive cell culture surface using poly(N‐isopropylacrylamide)

Poly(N‐isopropylacrylamide) (PIPAAm), which is a well‐known temperature‐responsive polymer, is modified on substrates by various methods. At 37 °C, PIPAAm modified surface is hydrophobic and allows cells to adhere to and proliferate on the surface. By reducing temperature below the lower critical solution temperature of PIPAAm, the surface turns to hydrophilic and allows cells to detach themselves from the surface spontaneously. With this technology, cell sheet engineering is established several years ago. This review focuses on the preparations and characteristics of PIPAAm‐modified surfaces, and discusses the effect of surface properties on cell adhesion and deadhesion. In addition, the recent improvement of PIPAAm‐modified surfaces for cell culture and the clinical applications of cell sheets harvested from the surfaces are also mentioned. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 917–926     

Synthesis of guanidinium‐based anion exchange membranes and their stability assessment

Alkaline fuel cells potentially offer improved conversion efficiency and the prospect of using non‐noble metal catalysts; however, low conductivity and fast degradation of anion exchange membranes (AEMs) prevent their widespread application. In this work, a series of novel composite AEMs were synthesized by incorporating guanidinium‐based polymers into a porous polytetrafluoroethylene (PTFE) film. The guanidinium‐based polymers were polymerized using a condensation process between a guanidinium salt and two different diamines so that the guanidinium cations were tethered to the polymer backbone to enhance both conductivity and durability. In addition, polymer crosslinking was conducted to further reinforce the mechanical strength of the membranes and interlock the guanidinium moieties to the porous PTFE. It was found that the ionic conductivity of the synthesized membrane reached up to approximately 80 mS cm^?1 at 20°C in deionized water. These membranes also exhibited superior stability compared to commercial quaternary ammonium AEMs after being exposed in 5 M KOH solution at 55°C for 50 h. Copyright © 2013 John Wiley & Sons, Ltd.     

Dual roles of alkyl alcohols as syndiotactic‐specificity inducers and accelerators in the radical polymerization of N‐isopropylacrylamide and some properties of syndiotactic poly(N‐isopropylacrylamide)

The effects of simple alkyl alcohols on the radical polymerization of N‐isopropylacrylamide in toluene at low temperatures were investigated. We succeeded in the induction of syndiotactic specificity and the acceleration of polymerization reactions at the same time by adding simple alkyl alcohols such as 3‐methyl‐3‐pentanol (3Me3PenOH) to N‐isopropylacrylamide polymerizations. The dyad syndiotacticity increased with a decrease in the temperature and an increase in the bulkiness of the added alcohol and reached up to 71% at ?60 °C in the presence of 3Me3PenOH. With the assistance of NMR analysis, it was revealed that the alcohol compounds played dual roles in this polymerization system; an alcohol compound coordinating to the N? H proton induced syndiotactic specificity, and that hydrogen‐bonded to the C?O oxygen accelerated the polymerization reaction. The effect of syndiotacticity on the properties of poly(N‐isopropylacrylamide)s was also examined in some detail. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4450–4460, 2006     

Effect of the crosslinking level on the properties of temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels

In this study, the effect of the level of crosslinking on the properties of poly(N‐isopropylacrylamide) (PNIPAAm) hydrogels was investigated in terms of their lower critical solution temperature (LCST), interior morphology, equilibrium swelling, and deswelling and swelling kinetics. The thermal analysis showed that PNIPAAm hydrogels, having a wide range of crosslinking levels, exhibited almost the same LCSTs, and this was different from what the conventional theory would have predicted. Scanning electron micrographs revealed that the interior network structure of the PNIPAAm matrix became more porous with an increase in the level of crosslinking. This more porous matrix provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external temperature changes during the deswelling process and the swelling process. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 582–593, 2003     

Effects of poly(N‐isopropylacrylamide) on the solution properties of hydrophobically modified acrylamide copolymer

The hydrophobic interaction between hydrophobically modified acrylamide copolymer (HMPAM) and poly(N‐isopropylacrylamide) (PNIPAM) in aqueous solutions was investigated. The results show that the solution properties of HMPAM are significantly influenced by the addition of PNIPAM. In dilute regime, the intrinsic viscosity of HMPAM in 0.025 wt % PNIPAM/0.1 M NaCl mixed solution is 17.52 dL g^?1, about 2 times 8.66 dL g^?1, that in 0.1 M NaCl solution, which is due to the attractive interaction between the hydrophobic parts of PNIPAM and HMPAM molecules. In semidilute regime, below the saturation concentration, the addition of PNIPAM can lead to both the apparent viscosity and the modulus of HMPAM solutions increasing, which is attributed to the number of aggregation junctions increasing, responsible for the increase of the contribution of the reversible network to the viscosity increase, the β value. In addition, a thermothickening behavior for the HMPAM/PNIPAM mixed solution is observed with increasing temperature over 15–30 °C, which is consistent with the large increase of the Huggins coefficient of HMPAM in the presence of PNIPAM from 1.95 to 7.59 as temperature increases from 25 to 30 °C. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 709–715, 2005     

Comb‐shaped guanidinium functionalized poly(ether sulfone)s for anion exchange membranes: Effects of the spacer types and lengths

A series of poly(ether sulfone)‐based anion exchange membranes (AEMs), tethering with guanidinium side chains with different spacers, were synthesized via azide‐alkyne cycloaddition, deprotection, and the subsequent ion exchange reactions. The designed polymer structures were verified by the ¹H NMR spectra. Because of the appropriate water uptake and formation of interconnected ionic clusters, the GPES‐3C with propyl spacer showed higher conductivity than the GPES‐1C and GPES‐9C, with methylene and nonyl spacers, respectively. Comparatively, the GPES‐EO AEM with two ethylene oxide (EO) spacers exhibited even higher conductivity, these can be interpreted by interconnectivity of ionic channels and hydrophilicity nature of the EO spacer. Additionally, although the GPES membranes displayed sufficient thermal stability, the chemical stability of as‐prepared materials needs to be much improved for fuel cell applications. Overall, these results demonstrated that the properties of “pendent‐type” AEM can be tuned facilely by the spacer types and lengths. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1313–1321     

The incorporation of carboxylate groups into temperature‐responsive poly(N‐isopropylacrylamide)‐based hydrogels promotes rapid gel shrinking

Aqueous gel deswelling rates for copolymer hydrogels comprising N‐isopropylacrylamide (IPAAm) and 2‐carboxyisopropylacrylamide (CIPAAm) in response to increasing temperatures were investigated. Compared with pure IPAAm‐based gels, IPAAm–CIPAAm gels shrink very rapidly in response to small temperature increases across their lower critical solution temperature (their volume is reduced by five‐sixths within 60 s). Shrinking rates for these hydrogels increase with increasing CIPAAm content. In contrast, structurally analogous IPAAm–acrylic acid (AAc) copolymer gels lose their temperature sensitivity with the introduction of only a few mole percent of AAc. Additionally, deswelling rates of IPAAm–AAc gels decrease with increasing AAc content. These results indicate that IPAAm–CIPAAm copolymer gels behave distinctly from IPAAm–AAc systems even if both comonomers, CIPAAm and AAc, possess carboxylic acid groups. Thus, we propose that the sensitive deswelling behavior for IPAAm–CIPAAm gels results from strong hydrophobic chain aggregation maintained between network polymer chains due to the similar chemical structures of CIPAAm and IPAAm. This structural homology facilitates aggregation of chain isopropylamide groups for both IPAAm and CIPAAm sequences with increasing temperature. The incorporation of AAc, however, shows no structural homology to IPAAm, inhibiting chain aggregation and limiting collapse. A functionalized temperature‐sensitive poly(N‐isopropylacrylamide) hydrogel containing carboxylic acid groups is possible with CIPAAm, producing rapid and large volume changes in response to smaller temperature changes. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 335–342, 2001     

Formation of pore‐filled ion‐exchange membranes with in situ crosslinking: Poly(vinylbenzyl ammonium salt)‐filled membranes

Robust, polyelectrolyte‐filled, microporous membranes were prepared by the introduction and crosslinking of a preformed polymer within the pores of a poly(propylene) host membrane. Specifically, poly(vinylbenzyl chloride) (PVBCl) was reacted with piperazine or 1,4‐diaminobicyclo[2.2.2]octane in an N,N‐dimethylformamide (DMF) solution contained in the pores of the microporous base membrane. The remaining chloromethyl groups were reacted with an amine, such as trimethylamine, to form positively charged ammonium sites. This simple two‐step procedure gave dimensionally stable, anion‐exchange membranes in which the degree of crosslinking and the mass loading were determined by the concentration of PVBCl and crosslinker in the starting DMF solution. The incorporated polyelectrolyte gel was evenly distributed within the pores of the host membrane with no surface layers present. The membranes are fully characterized. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 807–820, 2001     

Preparation and characterization of anion‐exchange membranes derived from poly(vinylbenzyl chloride‐co‐styrene) and intercalated montmorillonite

In this paper, three organic intercalating agents containing cations [hexadecyl trimethyl ammonium bromide (CTAB), poly(acrylamide‐co‐diallyldimethylammonium chloride), and quaternized polyethyleneimine] are used to prepare intercalated montmorillonites (MMT) by ion‐exchange method. Then the modified MMTs are doped with vinylbenzyl chloride and styrene copolymer [poly(vinylbenzyl chloride‐co‐styrene)] for fabricating composite anion‐exchange membranes (AEM). Fourier transform infrared, X‐raydiffraction, thermogravimetric analysis, scanning electron microscopy, and Mastersizer laser particle size analyzer are employed to characterize the structure and morphology of MMTs and AEMs. The successful intercalation of MMTs is approved, and the MMT intercalated by CTAB shows an interlayer distance of 2.31 nm. The properties of the composite membranes including water uptake, mechanical property, and ionic conductivity are investigated. Among all the AEMs, the composite membrane containing MMT sheets with CTAB demonstrates better compositive performances. It presents an ionic conductivity of 2.09 × 10^?2 S cm^?1 at 80°C and good alkaline solution stability. Copyright © 2016 John Wiley & Sons, Ltd.     

Electrodialytic transport properties of anion-exchange membranes in the presence of α-cyclodextrin

Electrodialysis of mixed salt solutions, sodium chloride and sodium sulfate, and sodium chloride and sodium nitrate, was carried out in the presence of α-cyclodextrin using commercial anion-exchange membranes. It was confirmed by several methods that the compound existed in the membrane matrix when the membrane had been immersed in its aqueous solution, though the molecular weight of α-cyclodextrin is relatively high. In electrodialysis, sulfate ions, large and strongly hydrated anions, easily permeated through the membranes and nitrate ions, less hydrated anions, permeated with difficulty through the membranes in the presence of α-cyclodextrin. Because α-cyclodextrin is a hydrophilic compound, which has many ether and alcoholic groups, the hydrophilicity of the anion-exchange membranes is thought to increase. Thus, sulfate ions easily permeate and nitrate ions permeate with difficulty. This proves that the hydrophilicity of the anion-exchange membranes controls permselectivity between anions through the membranes. Received: 8 August 2000 Accepted: 24 October 2000     

Synthesis,swelling properties,and network structure of new stimuli‐responsive poly(N‐acryloyl‐N′‐ethyl piperazine‐co‐N‐isopropylacrylamide) hydrogels

Poly(N‐acryloyl‐N′‐ethyl piperazine‐co‐N‐isopropylacrylamide) hydrogels were prepared by thermal free‐radical copolymerization of N‐acryloyl‐N′‐ethyl piperazine (AcrNEP) and N‐isopropylacrylamide (NIPAM) in solution using N, N′‐methylene bisacrylamide as the crosslinking agent. The gels were responsive to changes in external stimuli such as pH and temperature. The pH and temperature responsive character of the gels was greatly dependent on the monomer content, namely AcrNEP and NIPAM, respectively. The gels swelled in acidic (pH 2) and de‐swelled in basic (pH 10) solutions with a response time of 60 min. With increase in temperature from 23 to 80 °C the swelling of the gels decreased continuously and this effect was different in acidic and basic solutions. The temperature dependence of equilibrium water content of the gels was evaluated by the Gibbs–Helmholtz equation. Detailed analysis of the swelling properties of these new gels in relation to molecular heterogeneity in acidic (pH 2) and basic (pH 10) solutions were performed. Water transport property of the gels was studied gravimetrically. In acidic solution, the diffusion process was non‐Fickian (anomalous) while in basic solution, the diffusion was quasi‐Fickian. The effect was more evident in solution of pH 2 than in pH 10. Various structural parameters of the gels such as number‐average molar mass between crosslink (M_c), the crosslink density (ρ_c), and the mesh size (ξ) were evaluated. The mesh sizes of the hydrogels were between 64 and 783 Å in the swollen state in acidic solution and 20 and 195 Å in the collapsed state in basic solution. The mesh size increased between three to four times during the pH‐dependent swelling process. The amount of unbound water (free water) and bound water of the gels was also evaluated using differential scanning calorimetry. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Deswelling comparison of temperature‐sensitive poly(N‐isopropylacrylamide) microgels containing functional ?OH groups with different hydrophilic long side chains

Two monomers containing functional ? OH groups with different hydrophilic long side chains (viz., triethyleneglycol methacrylate (TREGMA) and polyethyleneglycol methacrylate (PEGMA)) were selected to modify the swelling/deswelling behavior of poly(N‐isopropylacrylamide) (pNIPAM) microgels. Dynamic scattering technique, turbidimetric method, and differential scanning calorimetry (DSC) were employed to investigate the deswelling behavior of the microgels. Experimental results show that the two series of microgels are identical in that incorporation of hydrophilic chains containing ? OH groups causes the volume‐phase transition temperature (VPTT) of pNIPAM microgels to shift to higher temperature; the more hydrophilic the side chains, the more the VPTTs shift. Although PEGMA are more effective in elevating the VPTTs of pNIPAM microgels than TREGMA, p(NIPAM‐co‐TREGMA) microgels show better deswelling properties than p(NIPAM‐co‐PEGMA) microgels, i.e., they have much larger deswelling ratios (α) and display less continuous volume‐phase transition. The VPTTs of the modified microgels can be modulated to well close to the normal body temperature of human beings. These characteristics along with the functional ? OH groups they contain make the microgels competitive candidates for biomaterials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3575–3583, 2005     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Thermoresponsive properties of porous poly(N‐isopropylacrylamide) hydrogels prepared in the presence of nanosized silica particles and subsequent acid treatment

Porous poly(N‐isopropylacrylamide) hydrogels were prepared by the free‐radical polymerization of its monomer and a suitable crosslinker in the presence of spherical silica particles of different sizes (74 and 1600 nm) and by the subsequent acid extraction of silica. The yields were 81–83%, and the yields were not affected by the silica content. Scanning electron microscopy observations revealed the porous structure of the hydrogels. Porous and nonporous hydrogels showed volume phase transitions from swelling states to deswelling states at approximately 30 °C, as analyzed by the ratio of the diameter of cylinder‐shaped hydrogels to that of the glass tube used for the hydrogel preparation at the corresponding temperature. Deswelling, which was analyzed by rapid changes in the temperature of the aqueous media from 20 to 40 °C, was facilitated by decreased silica particle size and increased silica content. The deswelling rate constant of the hydrogel prepared with 74‐nm silica at 10 v/v % (silica/solvent) was more than 1500 times greater than that of conventional hydrogels. Swelling was similarly analyzed through changes in the temperature from 40 to 20 °C and was independent of the pore structure. The deswelling–swelling cycle was repeatable with reasonable reproducibility. Moreover, the mechanical strength of the porous hydrogels was significantly maintained compared with that of conventional nonporous hydrogels. This method produced thermoresponsive hydrogels of suitable mechanical strength and remarkable deswelling properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4228–4235, 2002     

Effects of water nanochannel diameter on proton transport in proton‐exchange membranes

The effects of water nanochannel diameter on proton transport pathways and properties have been studied using reactive molecular dynamics simulations. The proton distributions and diffusivities have been evaluated using the cylinder model of water domains at various diameters that is the most typical proposed morphological model in proton‐exchange membranes. The proton distributions are analyzed to clarify proton pathways by classifying the water channel into two regions in parallel: an inner channel (free water) and an outer channel (bound water). For all the water contents, the nonmonotonic trends that show a peak at a certain diameter are found to be observed in the proton diffusivity, which is dominated by the proton diffusivity in the free water region and has a strong correlation with the proton distribution that is controlled by the balance between the volume fraction of free water and the surface density of sulfonate groups. The electroosmotic drag coefficients are found to increase monotonically with increasing channel diameter as a result of the increase in the volume fraction of free water. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 867–878     

Effect of chain architecture on the phase transition of star and cyclic poly(N‐isopropylacrylamide) in water

The heat‐induced phase transition of aqueous solutions of Poly(N‐isopropylacrylamide) (PNIPAM) in water is examined for a four‐arm PNIPAM star (s‐PNIPAM), a cyclic PNIPAM (c‐PNIPAM), and their linear counterparts (l‐PNIPAM) in the case of polymers (1.0 g L^?1) of 12,700 g mol^?1 < M_n < 14,700 g mol^?1. Investigations by turbidity, high‐sensitivity differential scanning calorimetry (HS‐DSC), and light scattering (LS) indicate that the polymer architecture has a strong effect on the cloud point (T_c: decrease for s‐PNIPAM; increase for c‐PNIPAM), the phase transition enthalpy change (ΔH decrease for s‐PNIPAM and c‐PNIPAM), and the hydrodynamic radius of the aggregates formed above T_c (R_H: c‐PNIPAM < s‐PNIPAM < l‐PNIPAM). The properties of s‐PNIPAM are compared with those of previously reported PNIPAM star polymers (3 to 52 arms). The overall observations are described in terms of the arm molecular weight and the local chain density in the vicinity of the core of the star, by analogy with the model developed for PNIPAM brushes on nanoparticles or planar surfaces. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2059–2068.