Amine-quinone polyurethanes. I. Preparation of polyurethane block copolymers containing 2,5–bis(N-2-hydroxyethyl-N-methylamino)-1,4–benzoquinone diol monomer

The amine-quinone monomer, 2,5–bis(N-2-hydroxyethyl-N-methylamino)-1,4-benzoqui-none (AQM-1), was prepared by the multiple-step condensation of 2-(N-methylam-ino)ethanol with benzoquinone in the presence of oxygen. This crystalline monomer was used to prepare a series of amine-quinone polyurethanes by condensation polymerization, either in the melt or in solution (THF or DMF), with a diisocyanate (MDI, TDI, or IPDI) and an oligomeric diol [poly(caprolactone) or poly(1,2-butylene glycol)]. The amine-quinone functional group was stable under the polymerization conditions, and was incorporated into the main chain, giving red-brown polyurethanes that had molecular weights in the range of 11,000–90,000 and were soluble in THF, MEK, DMF, and DMSO. The thermal properties were consistent with a two-phase morphology with an amorphous soft segment, containing the oligomeric diol, and a microcrystalline hard segment, containing AQM-1. The polymers having a low hard segment content (<50%) were rubbery (soft segment T_g <?25°C); polymers having a high hard segment content (>50%) were thermoplastic (hard segment T_g>150°C). © 1995 John Wiley & Sons, Inc.     

Preparation of sulfur‐quinone polyurethanes and their use to inhibit the corrosion of iron particles

A sulfur‐quinone diol monomer, 2,5‐bis‐(2‐hydroxyethylthio)‐1,4‐benzoquinone (SQM‐2), was prepared by the reaction of 2‐mercaptoethanol with benzoquinone. SQM‐2 and polycaprolactone diol (number‐average molecular weight = 1250) were condensed with toluene diisocyanate to give sulfur‐quinone polyurethanes. Two compositions were prepared, SQPU‐1 containing 7 mol % SQM‐2 and SQPU‐2 containing 35 mol % SQM‐2. These thermoplastic polyurethanes were soluble in solvents used in magnetic tape coating processes. The polymers were used to prepare magnetic coatings containing state‐of‐the‐art commercial iron particles. The sulfur‐quinone polyurethanes protected the iron particles against corrosion from a pH 2.0 aqueous buffer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3278–3283, 2000     

Synthesis of high‐performance polyurethanes with rigid 5‐6‐5‐fused ring system in the main chain from naturally occurring myo‐inositol

A bisketal of myo‐inositol was used as a diol‐type monomer for synthesis of polyurethanes. The monomer was obtained by treatment of myo‐inositol with 1,1‐dimethoxycyclohexane in the presence of p‐toluenesulfonic acid as a catalyst. The ketalization resulted in the formation of a 5‐6‐5‐fused ring system, which endowed the diol‐type monomer with high rigidity. The diol readily reacted with diisocyanate to give the corresponding polyurethane, which exhibited excellent heat resistance due to the rigid 5‐6‐5 system in the main chain. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3956–3963     

Free-radical synthesis of poly(urethane-g-N-vinyl pyrrolidone)

Relatively high-molecular-weight segmented polyurethanes based on methylene bis(4-phenyl-iso-cyanate), poly(propylene glycol), butane-1,4 diol, and cis-2-butene-1,4 diol have been synthesized and characterized. These unsaturated polyurethanes were successfully grafted using N-vinyl pyrrolidone as monomer and 2,2′-azobisisobutyronitrile as free-radical initiator. However, grafting experiments involving benzoyl peroxide as initiator were unsuccessful. The graft copolymers were isolated from the ungrafted polyurethane and poly(N-vinyl pyrrolidone) by selective solvent extraction. Elemental microanalysis, IR, NMR, thermogravimetric analysis, and equilibrium water sorption measurements were used to characterize the graft copolymers.     

Low- and high-conversion studies of the free radical copolymerization of 2-hydroxyethyl methacrylate with styrene in N,N′-dimethylformamide solution

2-Hydroxyethyl methacrylate (HEMA) and styrene (S) have been copolymerized in a 3 mol · L⁻¹N,N′-dimethylformamide (DMF) solution using 2,2′azobis (isobutyronitrile) (AIBN) as an initiator over a wide composition and conversion range. From low-conversion experiments and ¹H-NMR analysis, the monomer reactivity ratios were determined according to the Mayo–Lewis terminal model. The comparison of the obtained results with those previously reported for copolymerization in bulk and in toluene reveals a relatively small but noticeable solvent effect that can be qualitatively explained by the bootstrap model. Cumulative copolymer composition as a function of conversion is satisfactorily described by the integrated Mayo–Lewis equation; overall copolymerization rate increases with increasing the HEMA/S ratio, and individual monomer conversion is closely related to the monomer molar fraction in the feed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2941–2948, 1999     

Alkyne‐containing phthalonitrile resins: Controlling mechanical properties by selective curing

An alkyne‐containing multiple aromatic ether‐linked phthalonitrile has been synthesized and characterized. The oligomeric phthalonitrile monomer was prepared from the reaction of an excess amount of bisphenol A with 4,4′‐dibromotolane in the presence of K₂CO₃ in a N,N‐dimethylformamide/toluene solvent mixture, followed by end‐capping with 4‐nitrophthalonitrile in a two‐step, one‐pot reaction. After being cured in the presence of bis(4‐[4‐aminophenoxy]phenyl)sulfone, the polymeric properties of the alkyne‐ and non‐alkyne‐containing oligomeric phthalonitrile resins were compared. Rheometric measurements and thermogravimetric analysis showed that the alkyne‐containing oligomeric phthalonitrile resin had better mechanical properties than an analogous non‐alkyne‐containing resin cured under identical conditions and exhibited excellent thermal and oxidative properties. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4774–4778     

Synthesis and characterization of biodegradable poly(ϵ‐caprolactone urethane)s. I. Effect of the polyol molecular weight,catalyst, and chain extender on the molecular and physical characteristics

Biodegradable polyurethanes with potential for applications in medical implants were synthesized in bulk with aliphatic hexamethylene diisocyanate, isophorone diisocyanate, poly(?‐caprolactone) diols of various molecular weights, 1,4‐butane diol, 2‐amino‐1‐butanol, thiodiethylene diol, and 2‐mercaptoethyl ether chain extenders. The catalysts used were stannous octoate, dibutyltin dilaurate, ferric acetyl acetonate, magnesium methoxide, zinc octoate, and manganese 2‐ethyl hexanoate. The synthesis reactions were second‐order. All the materials had narrow, unimodal molecular weight distributions and polydispersity indices of 1.5–1.9. The chemical structures of the polyurethanes, as assessed from ¹H NMR and ¹³C NMR spectra, were in good agreement with the monomer stoichiometric ratios. The glass‐transition temperatures of the materials ranged from ?38 to ?57 °C and were higher for polymers based on isophorone diisocyanate and with higher hard‐segment contents. For polyurethanes with the same hard‐segment content, there was no effect of the material molecular weight on the thermal properties. The tensile strengths of the materials were 12–63 MPa, and the tensile moduli were 8–107 MPa. These increased with an increasing hard‐segment content. The least effective catalyst was magnesium methoxide, and the most effective was ferric acetyl acetonate. Stannous octoate and manganese 2‐ethyl hexanoate were less effective than dibutyltin dilaurate and zinc octoate. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 156–170, 2002     

Effect of polyester zigzag structure on the phase segregation of polyester-based polyurethanes

Polyester-based polyurethanes were synthesized from 4,4′-methylenebis(phenyl isocyanate) (MDI) with butanediol as a chain extender and low molecular weight polyester–diol as a soft segment. Two polyesters were used in the synthesis of polyurethanes. One of the polyesters was synthesized from adipic acid and 1,6-hexanediol, which had an even number of carbon atoms. The other polyester was synthesized from pimelic acid and 1,5-pentanediol, which had an odd number of carbon atoms. The effect of even carbon monomers and odd carbon monomers of polyester soft segments on the phase segregation of soft and hard segments was studied by DSC (differential scanning calorimetry) and FTIR (Fourier transform infrared spectroscopy). © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2095–2104, 1999     

Synthesis of heterocyclic monomers via Reissert chemistry

The chemistry of Reissert compounds has been used to synthesize activated difluorotetraketone monomers containing two coupled isoquinolyl moieties, linked at either the 1,1′‐ or 4,4′‐positions. These monomers offer routes to novel families of poly(heteroarylene ether)s. New 4,4′‐coupled bis(Reissert compound) 9 containing 4,4′‐diketo moieties failed to afford the desired difluorotetraketo monomer upon attempted rearrangement. However, analogous bis(Reissert compound) 19 containing 4,4′‐dibenzyl units did so, via aldehyde condensation, hydrolysis of the intermediate ester and oxidation of the four benzylic moieties to keto groups; thus the novel difluorotetraketone monomer 10 was prepared. Novel bis(Reissert compound)s 24 , 28 , and 35 were synthesized from diacid chlorides and 4‐(p‐fluorobenzyl)isoquinoline. Rearrangement of 24 to the diketone 29 , followed by oxidation of the 4‐benzyl moieties resulted in difluorotetraketone monomer 30 containing a 1,1′‐linked bisisoquinoline. The 1,1′‐linked bis(isoquinolylfluorodiketo) monomer 38 , isomeric with 10 , was prepared from 4‐(p‐fluorobenzyl) Reissert compound 36 by condensation with terephthaldehyde, ester hydrolysis to diol 37 , and oxidation. In the course of this effort, a number of new isoquinoline Reissert compounds were synthesized as model systems. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3856–3867, 2010     

Amine–quinone polyurethanes containing N‐alkylated amine–quinone monomers

A series of amine–quinone diol monomers, containing the 2,5‐diamino‐1,4‐benzoquinone group, were synthesized where the alkyl group on the amine was varied from methyl to ethyl to n‐propyl. Polyurethanes were prepared from these monomers by condensation polymerization in N,N‐dimethylformamide solution with toluene diiscyanate and poly(tetrahydrofuran) diol (M_n = 650). These amine–quinone polyurethanes were used as binders in metal particle tape. Samples were exposed to pH 2.0 aqueous buffer and the all amine–quinone polymers were shown to be superior in their ability to protect the iron particle against corrosion, relative to the commercial binders. There was no significant difference in the ability of the three amine–quinone polymers to inhibit corrosion. Clearly the increasing the steric bulk at the nitrogen did not affect their ability to inihibit corrosion. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3284–3292, 2000     

Solvent-induced self-organization approach for polymeric architectures of micropores,hexagons and spheres based on polyurethanes prepared via novel melt transurethane methodology

Solvent-induced self-organization approach was developed, for the first time, to produce polyurethane microporous templates and higher ordered morphologies such as micro or nanometer-sized polymeric hexagons and spheres. A novel melt transurethane methodology was designed and developed for synthesizing new class of cycloaliphatic polyurethanes under nonisocyanate and solvent-free conditions. In this new process, a diurethane monomer was polycondensed with equimolar amounts of diol in presence of Ti(OBu)₄ as catalyst with the removal of low boiling alcohol from the equilibrium. The hydrogen bonding of the polyurethanes are very unique to their chemical structure and they undergo selective phase-separation process in solution to produce hexagonally packed microporous templates. The increase of water content in the polymer solution enhances the phase-separation process and the micro pores coalesce to isolate the encapsulated polymer matrix into polymeric hexagons or densely packed solid spheres. The concentration-dependent solution FTIR and ¹H NMR of the polyurethanes revealed that the polymers possessing higher H-bonding association constants (K) have greater tendency to undergo solvent-induced self-organization phenomena. The mechanism of solvent-evaporation process indicated that only microporous polyurethanes have tendency to form higher ordered hexagons and spheres whereas others failed to show any new morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2351–2366, 2007     

Synthesis and characterization of new cardo polyimides prepared from 5,5-Bis[4-(4-aminophenoxy)phenyl]-4,7-methanohexahydroindane

A new cardo diamine monomer, 5,5-bis[4-(4-aminophenoxy)phenyl]-4,7-methanohexahydroindane (II), was prepared in two steps with high yield. The monomer was reacted with six different aromatic tetracarboxylic dianhydrides in N,N-dimethylacetamide (DMAc) to obtain the corresponding cardo polyimides via the poly(amic acid) precursors and thermal or chemical imidization. All the poly(amic acid)s could be cast from their DMAc solutions and thermally converted into transparent, flexible, and tough polyimide films which were further characterized by x-ray and mechanical analysis. All of the polymers were amorphous and the polyimide films had a tensile strength range of 89–123 MPa, an elongation at break range of 6–10%, and a tensile modulus range of 1.9–2.5 GPa. Polymers V_c, V_e, and V_f exhibited good solubility in a variety of solvents such as N-methyl-2-pyrrolidinone (NMP), DMAc, N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), pyridine, γ-butyrolactone, and even in tetrahydrofuran and chloroform. These polyimides showed glass-transition temperatures between 274 and 299°C and decomposition temperatures at 10% mass loss temperatures ranging from 490 to 521°C and 499 to 532°C in nitrogen and air atmospheres, respectively. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2815–2821, 1999     

Synthesis and thermal transition behavior of model thermoplastic polyurethanes containing MDI/butanediol‐based monodisperse hard segments

Amine‐terminated monodisperse hard segments (MDHSs) containing two to four 4,4′‐methylenebis (phenyl isocyanate) extended by 1,4‐butanediol have been synthesized using carboxybenzyl protecting‐deprotecting strategy. Pure MDHSs in large scale were obtained in good yield and their structures were confirmed by ¹H‐, ¹³C‐NMR spectroscopy and GPC‐MALLS. Differential scanning calorimetry (DSC) showed that as the hard segment (HS) size increased, the melting and glass transition temperature and the change of heat capacity at glass transition of ethyl capped MDHSs increased. Model thermoplastic polyurethanes (TPUs) were synthesized using the reaction of bischloroformate of poly (tetramethylene oxide) (PTMO) diol or polyisobutylene (PIB) diol with amine‐terminated MDHSs. X‐ray diffraction results indicated the amorphous structure of model TPUs. DSC revealed HS related endotherms, regardless of SS, which were attributed to the local ordering of the HSs. Additional endotherms in PTMO based model TPUs might arise from the dissociation of hydrogen bonding between PTMO and HSs. The lower T_g in model TPUs compared to the polydisperse analogues observed by dynamic mechanical analysis (DMA) indicated higher microphase separation of monodisperse HSs. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3171–3181     

Synthesis of hydroxyl‐bearing polyurethanes from naturally occurring myo‐inositol

A route from naturally occurring myo‐inositol to hydroxyl‐bearing polyurethanes has been developed. The diol prepared from the bis‐acetalization of myo‐inositol with 1,1‐dimethoxycyclohexane was reacted with a rigid diisocyanate, 1,3‐bis(isocyanatomethyl)cyclohexane to afford the corresponding polyurethane, of which glass transition temperature (T_g) was quite high as 192 °C. The polyurethane contains side chains inherited from the acetal moieties of the diol monomer and was treated with trifluoroacetic acid to hydrolyze the acetal moieties and afford the target polyurethane functionalized with hydroxyl groups. The presence of many hydroxyl groups in the side chains, which can form hydrogen bonds with each other, resulted in a high T_g, 186 °C. In addition, the hydroxyl groups were reacted with isocyanates to achieve further side‐chain modifications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1358–1364     

The effect of feed conditions in the emulsion catalytic chain transfer polymerization of alkyl methacrylates

([bis[μ-[(2,3-butanedione dioximato)(2-)-O:O′]] tetrafluorodiborato(2-)-N,N′,N″,N‴] cobalt), CoBF, has been used for the effective catalytic chain transfer of alkyl methacrylate homo- and copolymers under emulsion polymerization conditions. The catalytic chain transfer process reduces the rate of polymerization such that when the monomer is fed over 60 min the instantaneous conversion is low enough for the particle to be swollen with monomer, allowing diffusion of the catalysts between the aqueous and monomer phases. When the amount of the catalyst is reduced, the rate is increased, eventually leading to viscous, glassy particles that prevent catalyst mobility, which is observed as a breakdown in the polymerization mechanism. This can be circumvented by the addition of a 20% shot of monomer at the start of the reaction. The effective chain transfer coefficient decreases on increasing the length of the ester group of the methacrylate. The analysis of the polymers made by the technique described shows that the T_g of the polymers observe a broad transition due to the effect of chain length being pronounced at low molecular mass. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3549–3557, 1999     

Synthesis and properties of Ortho-linked aromatic polyamides based on 4,4′-(2,3-naphthalenedioxy) dibenzoic acid

A novel aromatic dicarboxylic acid monomer, 4,4′-(2,3-naphthalenedioxy)-dibenzoic acid ( 3 ), was prepared by the fluorodisplacement reaction of p-fluorobenzonitrile with 2,3-dihydroxynaphthalene in N,N-dimethylformamide (DMF) in the presence of potassium carbonate followed by alkaline hydrolysis of the intermediate dinitrile. A series of novel aromatic polyamides containing ortho-linked aromatic units in the main chain were synthesized by the direct polycondensation of diacid 3 and a variety of aromatic diamines using triphenyl phosphite and pyridine as condensing agents in the N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride. The resulting polyamides had inherent viscosities higher than 0.74 and up to 2.10 dL/g. All of these polyamides were soluble in polar solvents, such as NMP, DMF, N,N-dimethylacetamide (DMAc), and dimethyl sulfoxide. Transparent, flexible, and tough films could be cast from their DMAc or NMP solutions. The solvent-cast films had high tensile strengths and moduli. Extensions to break were relatively low, except for the polymers derived from 2,2-bis[4-(4-aminophenoxy)phenyl]hexafluoropropane and 3,4′-oxydianiline, which had elongations of 82 and 62%, respectively. Except for the polyamide based on p-phenylenediamine, all the other polyamides were amorphous in nature. All the polymers are thermally stable to temperatures in excess of 450°C in either air or nitrogen atmosphere. The polymers exhibited glass transition temperatures ranging from 183 to 260°C and decomposition temperatures (10% weight loss) ranging from 462–523°C in air and 468–530°C in nitrogen. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3385–3391, 1997     

Synthesis,polymerization, and curing of N‐substituted citraconimidyl acrylate

Several N‐(substituted phenyl) citraconimides containing phenolic hydroxyl groups (I) were prepared. I were esterified with acryloyl chloride producing the corresponding acrylate esters (II). II were free radically polymerized yielding linear polyacrylates (III). The citraconimidyl vinyls did not participate in the polymerization. The resulting polymers (III) were cured thermally or through the crosslinking agent N,N‐(p‐phenylene)dimaleimide. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 427–433, 1999     

Polyesters,polycarbonate, and polyurethanes from a novel monomer: α,α,α′,α′-tetramethyl-1,4-tetrafluorobenzenedimethanol

The novel diol monomer, α,α,α′,α′-tetramethyl-1,4-tetrafluorobenzenedimethanol, has been synthesized by a convenient route which involves the addition of acetone to 1,4-dilithiotetrafluorobenzene and can be purified by washing with hexanes. It does not directly undergo condensation polymerizations with diacid chlorides. Its disodium salt, prepared by its reaction with sodium hydride, similarly fails to undergo such polymerizations readily. However, the dilithium salt, prepared in situ by the reaction of the title diol with 2 equiv of n-butyllithium in tetrahydrofuran, is suitable for the preparation of various classes of condensation polymers. Four polyesters and one polycarbonate derived from the reactions of the dilithium salt of the diol with adipoly dichloride, sebacoyl dichloride, isophthaloyl dichloride, terephthaloyl dichloride, and phosgene and two polyurethanes derived from its reactions with tolylene-2,4-diisocyanate and methylene-di-1,4-phenyl diisocyanate were prepared. Each was fully characterized by GPC, NMR, IR, and UV-visible spectroscopies, and the results of these studies are reported herein. © 1993 John Wiley & Sons, Inc.     

Synthesis and thermal crosslinking of oxazolidine‐functionalized polyurethanes

A new oxazolidine derivative was obtained from phenol, 2‐amino‐2‐methylpropane‐1,3‐diol and paraformaldehyde. The reaction of this novel oxazolidine diol with phenylisocyanate lead to a urethane model compound which can be polymerized thermally by oxazolidine ring opening to give a Mannich bridge structure. Linear segmented polyurethanes were prepared by reaction of different ratios of oxazolidine diol and commercial polyethylenglycol (M_w ～ 400) with 4,4′‐methylenbis (cyclohexylisocyanate) (HMDI, 90% isomers mixture). The polyurethanes were thermally characterized and crosslinked by oxazolidine ring opening to obtain materials which showed improved thermal stability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4965–4973, 2007     

Synthesis and self‐assembly of stimuli‐responsive amphiphilic block copolymers based on polyhedral oligomeric silsesquioxane

A novel POSS‐containing methacrylate monomer (HEMAPOSS) was fabricated by extending the side chain between polyhedral oligomeric silsesquioxane (POSS) unit and methacrylate group, which can efficiently decrease the steric hindrance in free‐radical polymerization of POSS‐methacrylate monomer. POSS‐containing homopolymers (PHEMAPOSS) with a higher degree of polymerization (DP) can be prepared using HEMAPOSS monomer via reversible addition–fragmentation chain transfer (RAFT) polymerization. PHEMAPOSS was further used as the macro‐RAFT agent to construct a series of amphiphilic POSS‐containing poly(N, N‐dimethylaminoethyl methacrylate) diblock copolymers, PHEMAPOSS‐b‐PDMAEMA. PHEMAPOSS‐b‐PDMAEMA block copolymers can self‐assemble into a plethora of morphologies ranging from irregular assembled aggregates to core‐shell spheres and further from complex spheres (pearl‐necklace‐liked structure) to large compound vesicles. The thermo‐ and pH‐responsive behaviors of the micelles were also investigated by dynamic laser scattering, UV spectroscopy, SEM, and TEM. The results reveal the reversible transition of the assembled morphologies from spherical micelles to complex micelles was realized through acid‐base control. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2669‐2683