Interaction of the low-molecular weight salts with cationic polyelectrolytes

The interaction of several mono-, di-, and trivalent anions with cationic polyelectrolytes having different contents in N,N-dimethyl-2-hydroxypropylen ammonium chloride units (polymer A) or tertiary amine N-atoms and PEG (polymer PEGA) in the main chain was studied by viscosimetric and conductometric measurements. Both methods have shown a stronger interaction for tri- and bi- than for univalent counterions. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2571–2581, 1997     

Interval kinetic gravimetric sorption of acetone in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Interval sorption kinetics of acetone in solvent cast films of random poly(ethylene terephthalate)-co-(ethylene 2,6-naphthalate) (PET-co-PEN) are reported at 35°C and at acetone pressures ranging from 0 to 7.3 cm Hg. Polymer composition is varied systematically from 0% to 50% poly(ethylene 2,6-naphthalate). Equilibrium sorption is well described by the dual-mode sorption model. Interval sorption kinetics are described using a two-stage model that incorporates both Fickian diffusion and protracted polymer structural relaxation. The incorporation of low levels of PEN into PET significantly reduces the excess free volume associated with the glassy state and, for these interval acetone sorption experiments in ∼ 5 μm-thick films, decreases the fraction of acetone uptake controlled by penetrant-induced polymer structural relaxation. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2973–2984, 1999     

A new process for producing polyamide from polyester

A new process for producing polyamide from polyester and diamine was proposed. An attempt was made to produce polyamide 6T from polyethyleneterephthalate or dimethylterephthalate with hexamethylenediamine in water, o‐dichlorobenzene and sulfolane. Characterization of the products by IR, elemental analysis, solution viscosity and GPC were carried out. It became clear that high molecular polyamide 6T could be obtained from polyethyleneterephthalate and hexamethylenediamine in sulfolane. The reaction mechanism was discussed from the viewpoint of the polymer effect and solvent effect. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1413–1423, 1999     

Model of processing‐induced microstructure formation in polymeric materials

A general, mechanistic, kinetic model is presented to predict polymer microstructure formation during processing. Applications of the model are presented for three specific cases. The model represents polymer molecules as Kramers chains which may or may not have nucleated. Three forces (hydrodynamic, Brownian, and intermolecular) that act on polymer molecules during processing were considered, which resulted in the presentation of the model as a diffusion equation. The input parameters account for the rheological and thermal history of the polymer melt, the specific type of polymer molecule, and the initial morphology. The solution of the diffusion equation yields a probability distribution function from which the transient and equilibrium morphology can be determined. The three specific cases were chosen to illustrate the versatility of the model and include: the extensional flow‐induced growth of extended chain crystals; the orientation of stiff molecules in solution undergoing shear flow well above the crystallization temperature; and the formation of folded chain vs. extended chain crystals in an extensional flow. Data are available for the first two cases and agree favorably with the model predictions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2571–2585, 1999     

Coarsening of the phase structure in immiscible polymer blends. Coalescence or ostwald ripening?

The results of theories of the Ostwald ripening and coalescence applied to molten quiescent polymer blends with dispersed phase structure were analyzed. From a comparison of predictions of the theories with available experimental results follows that coarsening of the phase structure in quiescent polymer blends with medium or high interfacial tension is induced by the coalescence. Both the mechanisms play a role in coarsening of the phase structure in blends with low interfacial tensions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 181–187, 1999     

Synthesis of a novel epoxy resin containing naphthalene moiety and properties of its cured polymer with phenol novolac

A new epoxy resin (Bis-ENA) containing naphthalene structure linked with a 1,4-bis(isopropylidene)phenylene was synthesized and was confirmed by elemental analysis, infrared spectroscopy, and ¹H nuclear magnetic resonance spectroscopy. To estimate the effect of naphthalene moiety on the cured polymer, an epoxy resin (Bis-EP) having phenyl moiety was synthesized, and curing behaviors of Bis-ENA and Bis-EP with phenol novolac were evaluated by differential scanning calorimetry. The incorporation of naphthalene structure into the resin backbone increased the curing temperature and reduced the curing reactivity. Thermal properties of the cured polymers obtained from Bis-ENA and Bis-EP with phenol novolac were examined by thermomechanical analysis and dynamic mechanical analysis. Mechanical properties and moisture resistance were evaluated by flexural strength, flexural modulus, and moisture absorption measurements. The cured polymer obtained from Bis-ENA showed higher glass transition temperature, higher flexural modulus, lower thermal expansion, and lower moisture absorption than that from Bis-EP. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3063–3069, 1999     

Investigation of dipole alignments by swelling in poled thin films of a side-group polymer using second harmonic generation

This paper deals with relations between solvent diffusion and changes in second harmonic generation (SHG) in a side-group polymer with nonlinear optical (NLO) chromophores. The SHG signal of poled polymer thin films was measured as a function of time during the swelling process with methanol. The results indicated that the diffusion process was Fickian. The topographic results obtained by atomic force microscopy, together with the SHG data, also demonstrated the existence of the domain layer formed during poling that gave rise to the principal SHG intensity for this sample. Also, a noncentrosymmetric chromophore ordering was induced by swelling in the absence of a poling electric field. This time-varying SHG signal upon swelling was discussed in terms of dipolar and polar alignments of the side-group NLO chromophores. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 3108–3114, 1999     

Molecular surfaces: An advantageous starting point for the description of composition‐dependent viscosities applied to polymer solutions

The viscosity of polymer/solvent systems is modeled as a function of composition under the premises that the dissipation of energy is taking place at the molecular interfaces and that the friction between solvent and solute varies with composition due to a change in the flow mechanism (drainage of coils). The simple expression obtained in this manner contains three system‐specific parameters: a geometric factor γ, which accounts for the differences of the surface to volume ratios of the components; a hydrodynamic parameter α, which measures the friction between solute and solvent in the case of fully draining polymer coils; and β, which corrects for changes in the friction between unlike molecules resulting from collective motions owing to limited draining. Experimental data published for 12 poly(dimethylsiloxane)/pentamer mixtures can be represented quantitatively by this relation; moreover the knowledge of the three system‐specific parameters permits the calculation of intrinsic viscosities, and the molecular weight dependencies of γ and α yield the entangle molecular weight of the polymer. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2221–2228, 1999     

Chitosan‐based hydrogels: A new polymer‐based system with excellent laser‐damage threshold properties

Two types of chitosan hydrogel systems have been prepared that have a laser damage threshold (LDT) up to 35 times higher than commercial PMMA bulk materials. For these samples, the LDT increases with increasing water content. The mechanism of laser damage and the contribution of water to their high laser damage resistance have been examined. DSC measurements indicate water within the hydrogels exist in various states, each with different laser damage resistance properties. These various states play a key role in determining the LDT by controlling the dissipation of laser energy and providing a mechanism for self‐healing. This preliminary research shows that polymer hydrogels have potential for high power laser applications because they combine good mechanical integrity due to the polymer frame and good energy dissipation and healing characteristics due to the molecular mobility of water. These two traits allow for bulk shape‐retaining films with high laser damage thresholds and potential reversibility in damage processes. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 769–778, 1999     

Improved alternate deposition of biodegradable naturally occurring polymers onto a quartz crystal microbalance

The ultrathin polymer films that were composed of biodegradable and naturally occurring chitosan and poly(γ‐benzylglutamate) were stably deposited onto a quartz crystal microbalance (QCM) by alternate immersion of a QCM from their aqueous solutions in the presence of water‐soluble organic solvents as a USS soluble solvent. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 801–804, 1999     

Fast FTIR imaging: A new tool for the study of semicrystalline polymer morphology

The distribution of chemical species and the degree of orientation in semicrystalline polymer systems have been studied using fast Fourier transform infrared (FTIR) imaging. A variety of poly(ethylene glycol) systems, including pure polymer, high and low molecular weight blends, and blends with amorphous polymers, were studied. It is shown that fast FTIR imaging can be used to determine the distribution of species with different molecular weights and can be used to determine the degree of segregation of different components in blends with amorphous polymers. Additionally, by employing an infrared polarizer, the degree of orientation was determined in these systems by the generation of spatially‐resolved dichroic ratio images. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2353–2359, 1999     

Poly(methyl acrylate)/poly(hydroxyethyl acrylate) sequential interpenetrating polymer networks. Miscibility and water sorption behavior

Sequential poly(methyl acrylate)/poly(hydroxyethyl acrylate) interpenetrating polymer networks with different poly(hydroxyethyl acrylate) contents were prepared by free radical polymerization of hydroxyethyl acrylate inside the previously polymerized poly(methyl acrylate) network. Differential scanning calorimetry on dry samples shows that the interpenetrating polymer networks exhibit phase separation, and no differences are found between the glass transition temperatures of the two phases present in the interpenetrating polymer network and those of the pure components. Thermally stimulated depolarization current experiments were used to study the influence of water sorption on the mobility of the different molecular groups in the poly(hydroxyethyl acrylate) phase of the interpenetrating polymer network. Isothermal water sorption of the interpenetrating polymer networks and pure poly(methyl acrylate) and poly(hydroxyethyl acrylate) networks is analyzed with different theories to compare the behavior of the poly(hydroxyethyl acrylate) phase in the interpenetrating polymer networks with that of the pure poly(hydroxyethyl acrylate) network. Diffusion coefficients of water in the interpenetrating polymer networks are obtained by means of dynamic sorption experiments. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1587–1599, 1999     

Polymer solubility in mixed solvents

Modeling results indicate that polymer chains in mixtures of a good with a bad solvent exhibit preferential adsorption of the good solvent. That phenomenon is found to be strongly dependent on molecular weight and it increases with a decrease in chain length. These results have important consequences on polymer solubility. Thus, a low molecular weight chain in a solvent mixture behaves as if it were dissolved in the pure good solvent component, whereas the solubility of a longer chain is controlled by the average mixture composition. As a result, quenching a polydisperse system below the cloud point may induce molecular weight segregation between the two phases: the longer chains, which precipitate out first, tend to populate the polymer rich phase whereas the shorter chains, having greater solubility, remain in the solvent phase. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2782–2787, 1999     

In situ measurement of the thermal expansion behavior of benzocyclobutene films

In situ measurement techniques suitable for determination of the coefficient of thermal expansion (CTE) in thin, spin‐cast polymer films in both the in‐plane and through‐plane directions are presented. An examination of the thermal expansion behavior of cyclotene thin films has been performed. In particular, the effect of film thickness on the in‐plane and through‐plane CTE and in‐plane Young's modulus of spin‐coated cyclotene films was examined. It is shown that the mechanical response of in situ cyclotene films can be adequately described by isotropic film properties. It was also demonstrated that there is no thickness dependence on the free‐standing mechanical properties or on the resulting through‐plane thermal strain in an in situ film. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 311–321, 1999     

Synthesis of regiocontrolled polymer having 2-naphthol unit by CuCl-amine catalyzed oxidative coupling polymerization

Regiocontrolled polymer (2) having 2-naphthol unit was prepared by oxidative coupling polymerization of bis(2-naphthol) (1). Polymerizations were conducted in dichloromethane in the presence of [di-μ-hydroxo-bis(N,N,N′,N′-tetramethylethylenediamine)copper(II)] chloride [CuCl(OH)TMEDA] under air at room temperature, producing polymers with number-average molecular weights up to 12,000. The structure of polymer 2 was characterized by 270 MHz ¹H–NMR and 68.5 MHz ¹³C–NMR spectroscopies and was estimated to consist almost completely of 1,1′-linkage. The polymer was readily soluble in polar aprotic solvents and tetrahydrofuran at room temperature. Thermogravimetric analysis of polymer 2 showed 10% weight loss at 450°C in nitrogen. The model reactions were studied to clarify the applicability of CuCl(OH)TMEDA for coupling of naphthol derivatives. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3702–3709, 1999     

Polymer‐supported zirconocene catalyst for ethylene polymerization

The use of crosslinked poly(styrene‐co‐4‐vinylpyridine) having functional groups as the support for zirconocene catalysts in ethylene polymerization was studied. Several factors affecting the activity of the catalysts were examined. Conditions like time, temperature, Al/N (molar ratio), Al/Zr (molar ratio), and the mode of feeding were found having no significant influence on the activity of the catalysts, while the state of the supports had a great effect on the catalytic behavior. The activity of the catalysts sharply increased with either the degree of crosslinking or the content of 4‐vinylpyridine in the support. Via aluminum compounds, AlR₃ or methylaluminoxane (MAO), zirconocene was attached on the surface of the support. IR spectra showed an intensified and shifted absorption bands of C N in the pyridine ring, and a new absorption band appeared at about 730 cm⁻¹ indicating a stable bond Al N formed in the polymer‐supported catalysts. The formation of cationic active centers was hypothesized and the performance of the polymer‐supported zirconocene was discussed as well. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 37–46, 1999     

Luminescence studies of polymer matrices. III. Characterization and evaluation of acrylic acid‐based polymers as hosts for a phosphorescent coding system

The phosphorescence characteristics of naphthyl labelled poly(acrylic acid) film samples have been studied as a function of temperature, with a view to investigating the effect of matrix control on the level of triplet emission observed. Two relaxations, which serve to deactivate the excited triplet states have been detected from phosphorescence lifetime measurements: the α (or glass) and the βtransition (which can be associated with the onset of rotation of the carboxylic acid group). Investigation of the emission from 2‐benzoyl naphthalene dispersed within both an acrylic acid‐methyl methacrylate copolymer and a PAA film, respectively, has revealed that the more intense, longer‐lived phosphorescence results from the modified polymer. This is considered to reflect the existence of (i) hydrogen‐bonding interactions induced by the presence of carboxylic acid groups which serve to form a rigid matrix and (ii) intramolecular aggregates of methyl methacrylate units which create hydrophobic‐rich pockets, capable of sustaining intense phosphorescence at room temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2127–2136, 1999     

Near‐infrared spectroscopy for the quantitative determination of mass transfer and water absorption kinetics by a polymer solution

This article reports a new method to quantify the water absorption kinetics and the mass transfer in a polymer solution by using near‐infrared (NIR) spectroscopy and partial least‐squares (PLS) models, while it is exposed to a humid atmosphere. Polymer solutions used in this study were made with highly polar solvents exhibiting both a high affinity for water and a low volatility such as dimethylformamide, dimethylacetamide, and N‐methylpyrrolidone. Poly(ethersulfone) and poly(etherimide) were chosen as polymer models as the method could provide useful information for coating process and membrane fabrication monitoring. Whereas gravimetric kinetics yield data on the overall mass transfer, including both water absorption and solvent evaporation, in situ analyses using NIR can quantify separately the solvent and nonsolvent concentration change in the polymer solution. Quantitative models were developed using PLS regression to predict the local water, polymer, and solvent weight fractions in the polymer solution. The method was proved to be suitable for the different studied systems and allowed to infer mass transfers until the onset of the phase separation process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1960–1969, 2010     

Roughness correlation and interdiffusion in thin films of polymer chains

The surface morphology of thin bilayer polymer films on top of glass substrates was investigated. The bilayer consists of a blend film of protonated and deuterated polystyrene and an underlying deuterated polystyrene film. Choosing the thickness of the top film larger than 8 times and smaller than 2 times the radius of gyration of the chains enables the determination of film thickness and confinement effects. With diffuse neutron scattering at grazing incidence in the region of total external reflection, a depth sensitivity and a contrast even at the internal polymer–polymer interface was achieved. The underlying film is conformal to the substrate, and depending on the thickness of the top film two different types of roughness correlations are observed. Thin confined films nestle to the underlying polymer films, while the stiffness of thicker bulky films provides an independent morphology. In both cases, annealing above the glass-transition temperature yields an interdiffusion at the internal polymer–polymer interface, and the polymer–air surface remains essentially unchanged with respect to roughness correlations. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2862–2874, 1999     

Hydrogen-bonded supramolecular polymer networks

The strong dimerizing, quadruple hydrogen-bonding ureido-pyrimidone unit is used to obtain reversible polymer networks. A new synthetic route from commercially available starting materials is described. The hydrogen-bonding ureido-pyrimidone network is prepared using 3(4)-isocyanatomethyl-1-methylcyclohexyl-isocyanate (IMCI) in the regioselective coupling reaction of multi-hydroxy functionalized polymers with isocytosines. ¹H- and ¹³C-NMR, IR, MS, and ES-MS analysis, performed on a model reaction using butanol, demonstrated the formation of the hydrogen-bonding ureido-pyrimidone unit in a yield of more than 95%. The well-defined, strong hydrogen-bonding ureido-pyrimidone network is compared with a traditional covalently bonded polymer network, a multi-directional hydrogen-bonded polymer network based on urea units, and a reference compound. The advantage of the reversible, hydrogen-bonded polymer networks is the formation of the thermodynamically most favorable products, which show a higher “virtual” molecular weight and shear modulus, compared to the irreversible, covalently bonded polymer network. The properties of the ureido-pyrimidone network are unique; the well-defined and strong dimerization of the ureido-pyrimidone unit does not require any additional stabilization such as crystallization or other kinds of phase separation, and displays a well-defined viscoelastic transition. The ureido-pyrimidone network represents the first example of a truly reversible polymer network showing these features. Furthermore, the ureido-pyrimidone dimerization is strong enough to construct supramolecular materials possessing acceptable mechanical properties. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3657–3670, 1999