A.C. dielectric and TSC studies of constrained amorphous motions in flexible polymers including poly(oxymethylene) and miscible blends

Poly(OxyMethylene) (POM) and its miscible blends were studied by multifrequency A.C. dielectric and thermally stimulated currents (TSC). The blends contained small amounts of either poly(vinyl phenol), which is a high glass transition (T_g) diluent, or a styrene-co-hydroxy styrene oligomeric low T_g diluent. The variation of the 10°C “β” transition with blend composition proves that it is the glass transition, and that the −70°C “γ” transition is a local motion. Dielectrically the β transition is very weak in pure POM even in fast-quenched samples. The TSC thermal sampling method also detected two cooperative transitions, γ and β, in POM and its blends, and was used to directly resolve the γ transition into low and high activation energy components. If one considers the contribution of exclusion of the diluents from the crystal lamellae, it is shown that the blends behave like typical amorphous blends as a function of concentration. The effect of crystals on amorphous motions is examined in light of comparison with van Krevelen's³⁷ predictions of an “amorphous” T_g, and the transitions in POM are contrasted with those for other semicrystalline polymers. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2121–2132, 1997     

Lamellar thickening in nascent poly(acrylonitrile) upon annealing

No systematic study has been reported on the lamellar thickening in atactic poly(acrylonitrile) (PAN) upon annealing because PAN, in the form of solution‐cast films or their drawn products, generally shows no small‐angle X‐ray scattering (SAXS) maximum corresponding to the lamellar thickness. In this work, PAN crystals were precipitated during the thermal polymerization of acrylonitrile in solution. The nascent PAN film, obtained by the filtration of the crystal suspension, exhibited a clear SAXS maximum revealing the lamellar structure. The lamellar thickening upon annealing of the nascent PAN films was studied in the temperature range 100–180 °C, where the degradation was minimal, as confirmed by the absence of an IR absorption band at 1605 cm⁻¹ ascribed to the cyclized nitrile groups. Above 190 °C, the degradation of the samples was significant, and the SAXS became too broad to determine the scattering maximum. The long period was significantly affected by the annealing time (t_a) and the temperature (T_a). Depending on t_a, three stages were observed for the lamellar thickening behavior. The lamellar thickness stayed constant in stage I (t_a = 0.5–3 min, depending on T_a), rapidly increased in stage II (t_a = 0.5–8 min), and stayed at a constant value characteristic for each T_a at yet longer t_a's in stage III. The lamellar thickness characteristic for T_a increased rapidly with increasing T_a at 165 °C (or higher), which was 152 °C lower than the estimated melting temperature of PAN (T_m = 317 °C). A possible mechanism for such lamellar thickening in PAN far below the T_m is discussed on the basis of the enhanced chain mobility in the crystalline phase above the crystal/crystal reversible transition at 165–170 °C detected by differential scanning calorimetry and wide‐angle X‐ray diffraction. The structural changes associated with annealing are also discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2571–2579, 2000     

Time-resolved SAXS studies on crystallization behavior of polyõethylene isophthalate-co-ethylene terephthalatešs

Small-angle X-ray scattering measurements using synchrotron radiation were carried out for poly(ethylene terephthalate) and poly(ethylene isophthalate-co-ethylene terephthalate)s. In addition, differential scanning calorimetric measurements were conducted. Measurements were made both on polymers undergoing isothermal crystallization and during subsequent remelting. The primary and secondary crystallization behaviors are examined. Isophthalate units were found to be excluded from the crystals into amorphous layers during crystallization. No crystal thickening was observed during isothermal crystallization, which may be due to the relatively high chain rigidity. Secondary crystallization, detected predominantly at the later stages of crystallization, causes densification and shrinkage of the amorphous layer. Considering the results, it is proposed that secondary crystallization involves the formation of short-range molecular order in the amorphous layers of a lamellar stack as well as in the amorphous regions between lamellar stacks. This short-range-ordered phase has a lower density than the lamellar crystal formed by primary crystallization.     

Miscibility in crystalline/amorphous blends of poly(3-hydroxybutyrate)/DGEBA

A differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS) study of miscibility in blends of the semicrystalline polyester poly(3-hydroxybutyrate) (PHB) and amorphous monomer epoxy DGEBA (diglycidyl ether of bisphenol A) was performed. Evidence of the miscibility of PHB/DGEBA in the molten state was found from a DSC study of the dependence of glass transition temperature (T_g) as a function of the blend composition and isothermal crystallization, analyzing the melting point (T_m) as a function of blend composition. A negative value of Flory–Huggins interaction parameter χ_PD was obtained. Furthermore, the lamellar crystallinity in the blend was studied by SAXS as a function of the PHB content. Evidence of the segregation of the amorphous material out of the lamellar structure was obtained. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

MOLECULAR AND SUPRAMOLECULAR ORDERING IN CONFINED ENVIRONMENTS

Crystal and phase morphologies and structures determined by self-organization of crystalline-amorphous diblockcopolymers, crystallization of the crystallizable blocks, and vitrification of the amorphous blocks are reviewed through asystematic study on a series of poly(ethylene oxide)-b-polystyrene (PEO-b-PS) diblock copolymers. On the base ofcompetitions among these three processes, molecular and supramolecular ordering in confined environments can beinvestigated. In a concentration-fluctuation-induced disordered (D_(CF)) diblock copolymer, the competition between crystalli-zation of the PEO blocks and vitrification of the PS blocks is momtored by time-resolved simultaneous small angle X-rayscattering (SAXS) and wide angle X-ray diffraction (WAXD) techniques. In the case of T_c相似文献   

Crystallization and melting of poly(glycerol adipate)‐based graft copolymers with single and double crystallizable side chains

The crystallization and melting behavior of a series of poly(glycerol adipate) (PGA) based graft copolymers with either poly(ε‐caprolactone) (PCL), poly(ethylene oxide) (PEO), or PCL‐b‐PEO diblock copolymer side chains (i.e., PGA‐g‐PCL, PGA‐g‐PEO, and PGA‐g‐(PCL‐b‐PEO)) was studied using polarized light optical microscopy (POM), differential scanning calorimetry (DSC), small‐angle X‐ray scattering (SAXS), and wide‐angle X‐ray diffraction (WAXD). These results were compared with the behavior of the corresponding linear analogs (PEO, PCL, and PCL‐b‐PEO). POM revealed that spherulitic morphology was retained after grafting. However, spherulite radius as well as radial growth rate was significantly smaller in the graft copolymers. Evaluation of isothermal crystallization kinetics by means of the Avrami theory revealed that the nucleation density was much higher in the graft copolymers. The DSC results indicated that the degree of crystallinity decreased strongly upon grafting while the melting temperatures of PGA‐g‐PCL and PGA‐g‐PEO were found to be close to the values of neat PCL and PEO, respectively. This was attributed to the absence of specific thermodynamic interactions, and, additionally, to lamella thicknesses being similar to those of the homopolymers. The latter point was confirmed by SAXS measurements. In case of PCL‐b‐PEO diblock copolymers and PGA‐g‐(PCL‐b‐PEO) graft copolymers, the crystallization behavior and thus the resulting lamellar morphology is more complex, and a suitable model was developed based on a combination of DSC, WAXD, and SAXS data. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1581–1591     

Salt‐induced microphase separation of amorphous dendritic poly(ethylene oxide)‐block‐linear polystyrene copolymers

We prepared two block copolymers 1 and 2 consisting of a third‐generation dendron with poly(ethylene oxide) (PEO) peripheries and a linear polystyrene (PS) coil. The PS molecular weights were 2000 g/mol and 8000 g/mol for 1 and 2 , respectively. The differential scanning calorimetry (DSC) data indicated that neither of the block copolymers showed glass transition, implying that there was no microphase separation between the PEO and PS blocks. However, upon doping the block copolymers with lithium triflate (lithium concentration per ethylene oxide unit = 0.2), two distinct glass transitions were seen, corresponding to the salt‐doped PEO and PS blocks, respectively. The morphological analysis using small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM) demonstrated that a hexagonal columnar morphology was induced in salt‐doped sample 1‐Li⁺ , whereas the other sample ( 2‐Li⁺ ) with a longer PS coil revealed a lamellar structure. In particular, in the SAXS data of 2‐Li⁺ , an abrupt reduction in the lamellar thickness was observed near the PS glass transition temperature (T_g), in contrast to the SAXS data for 1‐Li⁺ . This reduction implies that there is a lateral expansion of the molecular section in the lamellar structure, which can be interpreted by the conformational energy stabilization of the long PS coil above T_g. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2372–2376, 2010     

Lamellar‐level morphology induced by combined crystallization and liquid–liquid demixing in a poly(ethylene terephthalate)/poly(ethylene‐2,6‐naphthalate) blend

The lamellar‐level morphology of an extruded poly(ethylene terephthalate) (PET)/poly(ethylene‐2,6‐naphthalate) (PEN) blend was investigated with small‐angle X‐ray scattering (SAXS). Measurements were made as a function of the annealing time in the melt and the crystallization temperature. The characteristic morphological parameters at the lamellar level were determined by correlation function analysis of the SAXS data. At a low crystallization temperature of 120 °C, the increased amorphous layer thickness was identified in the blend, indicating that some PEN was incorporated into the interlamellar regions of PET during crystallization. The blend also showed a larger lamellar thickness than pure PET. A reason for the increase in the lamellar thickness might be that the formation of thinner lamellar stacks by secondary crystallization was significantly restricted because of the increased glass‐transition temperature. At high crystallization temperatures above 200 °C, the diffusion rates of noncrystallizable components were faster than the growth rates of crystals, with most of the noncrystallizable components escaping from the lamellar stacks. As a result, the blend showed an interfibrillar or interspherulitic morphology. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 317–324, 2002     

Morphology development and crystallization behavior of poly(ethylene terephthalate)/phenoxy blend

The morphological development and crystallization behavior of a poly(ethylene terephthalate)/poly(hydroxyl ether of bisphenol A) (phenoxy) blend were studied with time‐resolved light scattering, optical microscopy, differential scanning calorimetry, and small‐angle X‐ray scattering (SAXS). During annealing at 280 °C, liquid–liquid phase separation via spinodal decomposition proceeded in the melt‐extruded specimen. After the formation of a domain structure, the blend slowly underwent phase homogenization by the interchange reactions between the two polymers. Specimens annealed for various times (t_s) at 280 °C were subjected to a temperature drop and the effects of liquid‐phase changes on crystallization were then investigated. The shifts in the position of the cold‐crystallization peaks indicated that the crystallization rate is associated with the composition change of the separated phases as well as the change of the sequence distribution in polymer chains during annealing. The morphological parameters at the lamellar level were determined by a correlation function analysis on the SAXS data. The crystal thickness (l_c) increased with t_s, whereas the amorphous layer thickness (l_a) showed little dependence on t_s. Observation of a constant l_a value revealed that a large number of noncrystallizable species formed by the interchange reactions between the two polymers were excluded from the lamellar stacks and resided in the interfibrillar regions, interspherulitic regions, or both. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 223–232, 2008     

Modulus and yield resistance of glassy blends containing diluents manifesting varying degrees of mobility: Polyphenylene ether/polystyrene/diluent mixtures

The glass temperatures, moduli, and yield stresses for shear failure have been characterized for homogeneous blends of poly(2,6-dimethyl-1,4-phenylene ether), homopolystyrene (1/1), and a number of diluents of T_gs from ?134 to +32°C. In a blend series based of a given diluent, the mechanical properties vary with blend T_g at rates that are characteristics of the particular diluent. These characteristic rates are found to depend strongly on the T_g of the neat diluent. Thus, for blends all with T_g = 90°C, for example, modulus and yield stress differ by as much as 50% over the range of diluents. Low-temperature relaxation measurements together with a number of previous dynamic spectroscopy studies of polymer/diluent systems at low temperatures suggest that many single-phase polymer/diluent blends may exhibit two primary relaxations—the depressed alpha relaxation of the resin and a somewhat elevated alpha relaxation of the diluent—at quite different temperatures. Both of these relaxations influence stiffness and strength properties at intermediate temperatures. The often-studied antiplasticization phenomena are viewed as a aberrations from a much more general influence of plasticizers on properties at temperatures below the alpha relaxation of the resin.     

Crystallization and chain conformation of semicrystalline and amorphous polymer blends studied by wide‐angle and small‐angle scattering

We examine the crystallization and chain conformation behavior of semicrystalline poly(ethylene oxide) (PEO) and amorphous poly(vinyl acetate) (PVAc) mixtures with wide‐angle X‐ray diffraction (WAXD), small‐angle X‐ray scattering (SAXS), and small‐angle neutron scattering (SANS) experiments. For blends with PEO weight fractions (wt_PEO) greater than or equal to 0.3, below the melting point of PEO, the WAXD patterns reveal that crystalline PEO belongs to the monoclinic system. The unit‐cell parameters are independent of wt_PEO. However, the bulk crystallinity determined from WAXD decreases as wt_PEO decreases. The scattered intensities from SAXS experiments show that the systems form an ordered crystalline/amorphous lamellar structure. In a combination of WAXD and SAXS analysis, the related morphological parameters are assigned correctly. With the addition of amorphous PVAc, both the average amorphous layer thickness and long spacing increase, whereas the average crystalline layer thickness decreases. We find that a two‐phase analysis of the correlation function from SAXS, in which the scattering invariant is linearly proportional to the volume fraction of lamellar stacks, describes quantitatively the crystallization behavior of PEO in the presence of PVAc. When wt_PEO is close to 1, the samples are fully spaced‐filled with lamellar stacks. As wt_PEO decreases from 1.0 to 0.3, more PVAc chains are excluded from the interlamellar region into the interfibrillar region. The fraction outside the lamellar stacks, which is completely occupied with PVAc chains, increases from 0 to 58%. Because the radius of gyration of PVAc with a random‐coil configuration determined from SANS is smaller than the average amorphous layer thickness from SAXS, we believe that the amorphous PVAc chains still persist with a random‐coil configuration even when the blends form an ordered structure. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2705–2715, 2001     

Poly(L-lactide) macrodiols (HOPLLAOH): Influence of linear alkyl diols as initiators: Synthesis and characterization

A series of α,ω-hydroxy telechelic poly(L-lactide)s (HOPLLAOHs) were synthesized by ring-opening polymerization (ROP) of L-lactide (L-LA) using tin octoate [Sn(Oct)₂] as catalyst and a family of linear alkyl diols as initiators [HO–[CH₂]_m–OH, where m = 2, 4, 6, 8, 10, and 12]. A systematic analysis of these HOPLLAOHs species in terms of their thermal properties was realized by DSC. In this sense, the linear alkyl group had an important influence on the glass transition temperature (T_g); a relatively high content of alkyl group on the HOPLLAOH increased the flexibility of the polyester, evidenced by a value of T_g inversely proportional to the weight percent of the alkyl group. Besides, the alkyl groups had an effect on the crystallization temperature (T_c), melting temperature (T_m), and crystallinity (x_i). Additionally, HOPLLAOHs were characterized by ¹H and ¹³C NMR, FT-IR, MALDI-TOF, and GPC.     

On the origin of the multiple melting behavior in poly(ethylene naphthalene‐2,6‐dicarboxylate): Microstructural study as revealed by differential scanning calorimetry and X‐ray scattering

In this article a study on the melting behavior and microstructure of semicrystalline poly(ethylene naphthalene‐2,6‐dicarboxylate) (PEN) prepared by crystallization from the glass under different annealing conditions is presented. The influence of the annealing temperature (T_a), annealing time (t_a), and the heating rate (R_h) at which T_a is reached on the endothermic behavior of the samples was investigated by means of differential scanning calorimetry (DSC). A dual melting behavior appeared for low R_h values (2 deg · min⁻¹) within the range of 145 °C < T_a < 250 °C and 1 min ≤ t_a. ≤ 16 h. Samples subjected to fast heating rates (R_h = 200 deg · min⁻¹) to reach a T_a ≥ 230 °C showed DSC traces in which a transition is observed from three peaks to a single melting peak when t_a increases in the 30–240 min range. On the basis of the DSC results, PEN samples were prepared displaying single or dual endothermic behavior. The microstructure of these samples was studied by wide (WAXS) and small‐angle X‐Ray scattering (SAXS) techniques. The SAXS data were analyzed using the correlation function and interface distribution function formalisms, respectively. In samples with a single melting behavior, microstructural parameters such as the long spacing, the amorphous and the crystalline phase thicknesses are consistent with a lamellar stacking model in which the thickness distributions of both phases are almost the same. For samples exhibiting two melting endotherms, a dual lamellar model, which is in agreement with the experimental results is proposed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1167–1182, 2000     

Effects of amorphous poly(vinyl acetate) on crystalline morphology of poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid)

The amorphous and crystalline phase behavior, spherulite morphology, and interactions between amorphous poly(vinyl acetate) (PVAc) and poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) (PHBV) were examined using differential scanning calorimetry, polarized-light optical and scanning electron, atomic-force microscopy (DSC, POM, SEM, AFM), and small-angle X-ray scattering (SAXS). The PHBV/PVAc blend was found to be miscible with an almost linear T _g-composition relationship, indicating perfect homogeneity. Interaction parameter by melting point depression is a negative value of χ = −0.32, suggesting quite favorable interaction strength. With the intimate interaction between the amorphous PVAc and crystalline PHBV polymers, effects of PVAc on the spherulitic morphology of PHBV are quite significant. Owing to the higher T _g of PVAc (than that of PHBV), the spherulite growth rate of PHBV was depressed by increasing PVAc content in blends. Neat PHBV exhibits ring-banded spherulites when crystallized at T_c = 60 ~ 110^° C {T_{\rm{c}}} = {6}0\sim {11}0^\circ {\hbox{C}} ; however, with increasing PVAc content in the blends, the temperature range at which the PHBV/PVAc blends exhibit ring-banded spherulites remains similar but the regularity increases, and the inter-ring spacing significantly decreases. In addition, the spherulite size and ring-band patterns therein are strongly dependent on T _max (190 vs. 220 °C, respectively, for erasing prior nuclei), from which the blends were quenched to a T _c (60–110 °C) for crystallization. For PHBV/PVAc blends crystallized at the same T _c from different T _max, higher T _max tends to erase nuclei, leading to larger spherulites. However, such larger spherulites owing to higher T _max are not necessarily packed with thicker lamellae.     

Glass transition,crystallization, and morphology relationships in miscible poly(aryl ether ketones) and poly(ether imide) blends

The relationships among glass transition, crystallization, melting, and crystal morphology of poly(aryl ether ketone) (PAEK)/poly(other imide) (PEI) blends was studied by thermal, optical and small-angle x-ray scattering (SAXS) methods. Two types of PAEK were chosen for this work: poly(aryl ether ether ketone), PEEK, and poly(aryl ether ketone ketone), PEKK, which have distinctly different crystallization rates. Both PAEKs show complete miscibility with PEI in the amorphous phase. As PAEK crystallizes, the noncrystallizable PEI component is rejected from the crystalline region, resulting in a broad amorphous population, which was indicated by the broadening and the increase of T_g over that of the purely amorphous mixture. The presence of the PEI component significantly decreases the bulk crystallization and crystal growth rate of PAEK, but the equilibrium melting temperature and crystal surface free energies are not affected. The morphology of the PEI segregation was investigated by SAXS measurements. The results indicated that the inter(lamellar-bundle) PEI trapping morphology was dominant in the PEEK/PEI blends under rapid crystallization conditions, whereas the interspherulitic morphology was dominant in the slow crystallizing PEKK/PEI blends. These morphologies were qualitatively explained by the expression δ=D/G, where G was the crystal growth rate and D was the mutual diffusion coefficient. © 1993 John Wiley & Sons, Inc.     

Relationship between morphology and glass transition temperature in solvent-crystallized poly(aryl ether ketones)

The relationship between semicrystalline morphology and glass transition temperature has been investigated for solvent-crystallized poly(ether ether ketone) (PEEK) and poly(ether ketone ketone) (PEKK). Solvent-crystallized specimens of both PEEK and PEKK displayed a sizeable positive offset in T_g compared to quenched amorphous specimens as well as thermally crystallized specimens of comparable bulk crystallinity; the offset in T_g for the crystallized samples reflected the degree of constraint imposed on the amorphous segments by the crystallites. Small-angle X-ray scattering studies revealed markedly smaller crystal long periods (d) for the solvent-crystallized specimens compared to samples prepared by direct cold crystallization. The strong inverse correlation observed between T_g and interlamellar amorphous thickness (l_A) based on a simple two-phase model was in excellent agreement with data reported previously for PEEK, and indicated the existence of a unique relationship between glass transition temperature and morphology in these poly(aryl ether ketones) over a wider range of sample preparation history and lamellar structure than was previously reported. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 65–73, 1998     

Study of the Crystallization of an Aromatic Poly-ether-ketone (PK99) by Calorimetric and X-ray Analysis

An analysis of the crystallization behaviour of a new poly(aryl-ether-ether-ketone-ketone), PK99, by differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD) is presented. Isothermal crystallization TG were obtained in the whole range between the glass transition temperature (T _g) and the melting temperature (T _m) as a consequence of the slow crystallization kinetics stemming from the closeness of these transitions. The calorimetric results, compared with WAXD data, were applied to determine the theoretical melting temperature and crystallization enthalpy. The DSC and WAXD data were combined in order to calculate the total amount of the crystallizable fraction of the polymer, and a model was proposed to explain the difference between the fractions of crystallinity observed with these techniques. The thermal and X-ray data were also correlated with different lamellar morphologies arising from the crystallization conditions. Finally, DSC experiments on the crystallized sample were used to detect the presence of a rigid amorphous phase which does not relax at T _g. This revised version was published online in July 2006 with corrections to the Cover Date.     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) and methoxy poly(ethylene glycol) blends

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHB‐HHx) and methoxy poly(ethylene glycol) (MPEG) blends were prepared using melt blending. The single glass transition temperature, T_g, between the T_gs of the two components and the negative χ value indicated that PHB‐HHx and MPEG formed miscible blends over the range of compositions studied. The Gordon–Taylor equation proved that there was an interaction between PHB‐HHx and MPEG in their blends. FTIR supported the presence of hydrogen bonding between the hydroxyl group of MPEG and the carbonyl group of PHB‐HHx. The spherulitic morphology and isothermal crystallization behavior of the miscible PHB‐HHx/MPEG blends were investigated at two crystallization temperatures (70 and 40 °C). At 70 °C, melting MPEG acted as a noncrystalline diluent that reduced the crystallization rate of the blends, while insoluble MPEG particles acted as a nucleating agent at 40 °C, enhancing the crystallization rate of the blends. However, no interspherulitic phase separation was observed at the two crystallization temperatures. The constant value of the Avrami exponent demonstrated that MPEG did not affect the three‐dimensional spherulitic growth mechanism of PHB‐HHx crystals in the blends, although the MPEG phase, such as the melting state or insoluble state, influenced the crystallization rate of the blends. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2852–2863, 2006     

α‐ and β‐Relaxations in neat and antiplasticized polybutadiene

Dielectric spectroscopy was carried out to measure the α‐relaxation (local segmental motion) and the higher frequency, secondary relaxation (β‐mode) in 1,4‐polybutadiene, both neat and containing a nonpolar diluent, mineral oil. The α‐relaxation shifted to lower frequencies (antiplasticization) in the presence of the diluent, suggesting the glass temperature of the latter is higher than the T_g of the polymer (i.e., >187K). The T_g of neat mineral oil cannot be determined directly, due to crystallization. While the diluent increased the magnitude of the α‐relaxation times, it had no effect on the β‐relaxation. Moreover, neither the shape of the α‐relaxation function nor its temperature dependence was influenced by the diluent. From this we conclude that the main effect of the mineral oil was to increase the local friction, without changing the degree of intermolecular cooperativity of the molecular motions. We also find that near the glass temperature, there is rough agreement between the time scale of the secondary relaxation process and the value of a noncooperative relaxation time estimated from theory. This approximate correspondence between the two relaxation times also holds for 1,2 polybutadiene. However, the β‐process cannot be identified with the noncooperative α‐relaxation, and the relationship between them is not quantitative. © 2000 John Wiley & Sons, Inc.* J Polym Sci B: Polym Phys 38: 1841–1847, 2000     

Synthesis and properties of novel aromatic poly(o-hydroxy amide)s and polybenzoxazoles based on the bis(ether benzoyl chloride)s from hydroquinone and its methyl-, tert-butyl-, and phenyl-substituted derivatives

Four series of poly(o-hydroxy amide)s were prepared by the low-temperature solution polycondensation of the bis(ether benzoyl chloride)s extended from hydroquinone and its methyl-, tert-butyl-, or phenyl-substituted derivatives with three bis(o-aminophenol)s. Most of the poly(o-hydroxy amide)s displayed an amorphous nature, were readily soluble in various polar solvents such as N,N-dimethylacetamide (DMAc), and could be solution-cast into flexible and tough films. These poly(o-hydroxy amide)s had glass transition temperatures (T_g) in the range of 152–185°C and could be thermally cyclodehydrated into the corresponding polybenzoxazoles approximately in the region of 200–400°C, as evidenced by the DSC thermograms. The thermally converted benzoxazole polymers exhibited T_gs in the range of 215–247°C and did not show significant weight loss before 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2129–2136, 1999