Complex‐radical terpolymerization of acceptor–donor–acceptor systems: Maleic anhydride (n‐butyl methacrylate)–styrene–acrylonitrile

Some features of radical ternary copolymerization of maleic anhydride (MA)–styrene (St)–acrylonitrile (AN) and n‐butyl methacrylate (BMA)–St–AN acceptor–donor–acceptor monomer systems have been revealed. The terpolymer compositions and kinetics of copolymerizations were studied in the initial and high conversion stages. The considerable divergence in the copolymer compositions was observed when a strong acceptor MA monomer was substituted with BMA having comparatively low acceptor character in the ternary system studied. Obtained results show that terpolymerization proceeded mainly through “complex” mechanism in the state of near binary copolymerization of St…MA (or BMA) and AN…St complexes only in the chosen ratios of complexed monomers. The terpolymers synthesized have high thermal stabilities (295–325 °C), which is explained by possible intermolecular fragmentation of AN‐units through cyclization and crosslinking reactions during thermotreatment in the isothermal heating conditions. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2652–2662, 2000     

Complex-radical terpolymerization of phenanthrene,maleic anhydride,and trans-stilbene

The radical terpolymerization of the donor-acceptor-donor monomer system, phenanthrene (P)—maleic anhydride (M)—trans-stilbene (S), was studied. These monomers are known to be nonhomopolymerizable. The terpolymerization was carried out in p-dioxane and/or toluene at 70°C in the presence of benzoyl peroxide used as the initiator. P and S were found to form charge transfer complexes (CTC) with M in p-dioxane at 35°C. The results obtained are discussed in terms of the free monomer and complex propagation models. It is shown that terpolymerization is carried out at a stage close to binary copolymerization of two complexomers. The reactivity ratio of P … M and S … M complexes was estimated by the Kelen-Tüdös method. Absorbance ratios at 1770 cm^?1 (v_C=0 of anhydride group), 764 cm^?1 (δ_CH in monosubstituted benzene of S), and 820 cm^?1 (δ_CH in disubstituted benzene of P) as a function of terpolymer composition were established. P—M—S terpolymers are shown to have high thermal stabilities. © 1995 John Wiley & Sons, Inc.     

Living radical copolymerization of styrene/maleic anhydride

Styrene/maleic anhydride (MA) copolymerization was carried out using benzoyl peroxide (BPO) and 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO). Styrene/MA copolymerization proceeded faster and yielded higher molecular weight products compared to styrene homopolymerization. When styrene/MA copolymerization was approximated to follow the first‐order kinetics, the apparent activation energy appeared to be lower than that corresponding to styrene homopolymerization. Molecular weight of products from isothermal copolymerization of styrene/MA increased linearly with the conversion. However products from the copolymerization at different temperatures had molecular weight deviating from the linear relationship indicating that the copolymerization did not follow the perfect living polymerization characteristics. During the copolymerization, MA was preferentially consumed by styrene/MA random copolymerization and then polymerization of practically pure styrene continued to produce copolymers with styrene‐co‐MA block and styrene‐rich block. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2239–2244, 2000     

Styrene-assisted melt free radical grafting of glycidyl methacrylate onto polypropylene

The free radical grafting reactivity of glycidyl methacrylate (GMA) onto polypropylene (PP) in the molten state is low. This article shows that adding styrene as a second monomer (or comonomer) increases both the rate and yield of GMA grafting and reduces PP chain scission. The proposed mechanism is that when St is added to the PP/GMA/peroxide grafting system, St reacts first with PP macroradicals to form stable styryl macroradicals. These latter then react (or copolymerize) with GMA to form GMA grafted PP. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1053–1063, 1998     

Ferrocene as an effective initiator for copolymerization of styrene with maleic anhydride

Ferrocene (Fc) was found to be an effective initiator for copolymerization of styrene (ST) with maleic anhydride (MAH). Copolymerization could be initiated by charge transfer complex formed between MAH as an electron acceptor and Fc as an electron donor. A good relationship between the formation of charge transfer complex and initiation activity was observed in the copolymerization of ST with MAH in various solvents. Overall energy of activation determined from an Arrhenius plot in dioxane was found to be 21.8 kJ/mol. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(styrene‐maleic anhydride)‐montmorillonite nanocomposite

Poly(styrene‐maleic anhydride)‐montmorillonite nanocomposites were prepared by intercalation of layered montmorillonite with the polymer ions. Synthetic approaches including polymerization and phosphonium salt formation have been used for polymer intercalation and dispersion of the host layers in the polymer matrix. The ratio of the mineral in the composites ranged 30–50%. Wide‐angle X‐ray diffraction (WAXD) disclosed that the d₍₀₀₁₎ spacing between the internal lamellar surface were only expanding to about 13 and 15 Å according to the type of phosphonium salt suggesting packing of polymer molecules between the layers. Examination of these materials by scanning and transmission electron microscopy showed spherical nano size particles of average diameter, 350 nm. Copyright © 2002 John Wiley & Sons, Ltd.     

Graft copolymerization of maleic anhydride/styrene onto isotactic polypropylene using supercritical CO2

The free‐radical grafting of maleic anhydride (MAH) and styrene (St) onto isotactic polypropylene (iPP) was studied by thermal decomposition of dicumyl peroxide (DCP) using supercritical CO₂ as a solvent and swelling agent. Several effects of molar ratio of monomer, soaking temperature and time, reaction time, and reaction pressure on the graft degree were discussed. It was found that the addition of St to the grafting system as a comonomer could significantly enhance the graft degree of the grafted PP. Under the optimal reaction condition, the maximum of iPP grafting MAH and St in supercritical CO₂ medium was 10.58%. The chemical structures and properties of grafting copolymers were characterized by Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The results showed that the supercritical CO₂ method had noticeable advantages over the existed method when compared, such as a lower temperature, a higher graft degree, easy separation, and environmentally benign. Copyright © 2007 John Wiley & Sons, Ltd.     

Controlled radical copolymerization of styrene and maleic anhydride and the synthesis of novel polyolefin‐based block copolymers by reversible addition–fragmentation chain‐transfer (RAFT) polymerization

Reversible addition–fragmentation chain transfer (RAFT) was applied to the copolymerization of styrene and maleic anhydride. The product had a low polydispersity and a predetermined molar mass. Novel, well‐defined polyolefin‐based block copolymers were prepared with a macromolecular RAFT agent prepared from a commercially available polyolefin (Kraton L‐1203). The second block consisted of either polystyrene or poly(styrene‐co‐maleic anhydride). Furthermore, the colored, labile dithioester moiety in the product of the RAFT polymerizations could be removed from the polymer chain by UV irradiation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3596–3603, 2000     

Self‐initiating performance of maleic anhydride on surface photografting polymerization

Maleic anhydride (MAH) was photografted onto low‐density polyethylene (LDPE) films with a grafting efficiency of about 70% in the absence of a photoinitiator. The self‐initiating performance was attributed to a mechanism of abstracting hydrogen atoms from LDPE chains by excited MAH dimers. The supporting experimental results were as follows: (1) the far‐UV radiation (200–300 nm) was indispensable for the graft polymerization and 2) the crosslinking reaction of LDPE inevitably accompanied the grafting of MAH. In addition, the initiation performance of MAH was further confirmed by surface photografting of acrylic acid in the presence of MAH, where MAH was used as the photoinitiator. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3246–3249, 2001     

Synthesis and metal complexation of dihydroxyphosphino‐functionalized crosslinked styrene/maleic anhydride copolymers

Crosslinked styrene (St)/maleic anhydride (MA) copolymers were synthesized, hydrolyzed with dicarboxylic acid, and converted to bear dihydroxyphosphino functionalities. The St–MA copolymers were prepared by azobisisobutyronitrile‐initiated polymerization in toluene at 90 °C in the presence of 2, 10, or 20% divinylbenzene crosslinker. The MA moiety was hydrolyzed into dicarboxylic acid to improve the hydrophilicity of the copolymers. The phenyl ring of St was phosphorylated with phosphorus trichloride in the presence of aluminum chloride and then hydrolyzed and oxidized with nitric acid at room temperature. The structures of the hydrolyzed and dihydroxyphosphino‐functionalized copolymers were confirmed by Fourier transform infrared spectroscopy and elemental analysis. The complexation behavior of these functionalized copolymers toward metal ions in 25 ppm aqueous solutions was observed over time periods of up to 7 h. The adsorption toward Pb(+2) was highest, followed by those of Cu(+2), Cr(+3), and Ni(+2). On the dihydroxyphosphino‐functionalized St–MA (20% divinylbenzene) copolymer, the adsorption of Pb(+2) showed a linear relationship with the concentrations and fit the Langmuir isotherm. The kinetics of Pb(+2) adsorption on this dihydroxyphosphino‐functionalized copolymer also fit the rate equation of the moving boundary model, t = [1 ? 3(1 ? X)^2/3 + 2(1 ? X)], where X is the fractional conversion. The metal‐ion adsorption kinetics of this copolymer appeared to be particle diffusion control, in which the moving boundary advanced from the surface toward the center. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 92–101, 2004     

Melt modification of poly(styrene‐co‐maleic anhydride) with alcohols in the presence of 1,3‐oxazolines

Various copolyesteramides were prepared by melt compounding at 220 °C involving reaction of poly(styrene‐co‐maleic anhydride), SMA, with 6, 17, and 28 wt % maleic anhydride content, and 1‐dodecanol, C12OH, in the presence of 2‐undecyl‐1,3‐oxazoline, C11OXA. Copolymer architectures were examined by means of ¹H NMR, FTIR, DSC, and TGA using model compounds prepared via solution reactions. While conversion of anhydride with alcohol was poor due to the thermodynamically favored anhydride ring formation, very high conversions were achieved when stoichiometric amounts of C11OXA were added. According to spectroscopic studies esteramide groups resulted from reaction of oxazoline with carboxylic acid intermediate. In the absence of alcohol, C11OXA reacted with anhydride to produce esterimides. Effective attachment of flexible n‐alkyl side chains via simultaneous reaction of C12OH and C11OXA resulted in lower glass‐transition temperatures of copolyesteramides. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1222–1231, 2000     

A study on free volume of acrylonitrile‐styrene copolymer and methyl methacrylate‐styrene copolymer by using positron annihilation

The o‐Ps lifetime τ₃ and the intensity I₃ of ST‐AN copolymers and ST‐MMA copolymers have been determined by using the positron annihilation technique. The average free volume hole radius R is estimated according to Tao's and Eldrup's model. The result shows that the average free volume hole size mainly attributes to lateral group volume and polarity of macromolecular chain as well as polymerizing temperature, and the o‐Ps intensity I₃ to the effect of the lateral group volume and the polarity. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 465–472, 1999     

Synthesis and application of modified poly (styrene‐alt‐maleic anhydride) networks as a nano chelating resin for uptake of heavy metal ions

A chelating resin based on modified poly (styrene‐alt‐maleic anhydride) with 3‐aminobenzoic acid was synthesized. This modified resin was further reacted by 1,2‐diaminoethane or 1,3‐diaminopropane in the presence of ultrasonic irradiation to prepare tridimensional chelating resin for the removal of heavy metal ions from aqueous solutions. The adsorption behavior of Fe(II), Cu(II), Zn(II) and Pb(II) ions was investigated by synthesized chelating resins in various pH. Among the synthesized resins, CSMA‐AB1 and CSMA‐AB2 demonstrated a high affinity for the selected metal ions compared to SMA‐AB, and the order of removal percentage changes as follow: Fe(II) > Cu(II) > Zn(II) > Pb(II). The adsorption of all metal ions in acidic medium was moderate, and it was favored at the pH value of 6 and 7. Also, the prepared resins were examined for removal of metal ions from industrial wastewater and were shown to have a very efficient adsorption in the case of Cu(II), Fe(II) and Pb(II); however, the adsorption of Zn(II) was lower than others. The resin was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X‐ray diffraction analysis and thermogravimetric analysis/derivative thermogravimetry. Copyright © 2012 John Wiley & Sons, Ltd.     

Cobalt complex bearing β‐ketoamine ligand: syntheses,structure, catalytic behavior for styrene and methyl methacrylate polymerization

Cobalt complex based on β‐ketoamine ligand [(Z)‐4‐((2,5‐dimethylphenylamino) (phenyl)methylene)‐3‐methyl‐1‐phenyl‐1H‐pyrazol‐5(4H)‐one] was successfully synthesized. The produced catalyst showed satisfactory activities in the cobalt‐mediated radical polymerization of styrene and methyl methacrylate with the common initiator of AIBN. The resulting polymerizations have the characteristics of living radical polymerization and displayed a nearly linear correlation between the number‐average molecular weight and monomer conversion. Low polydispersity was obtained for all polymerizations, and the polydispersity index decreased with the increase of conversion. These improvements facilitate the implementation of styrene and methacrylate cobalt‐mediated radical polymerization, and open the door to the scale‐up of the process. Copyright © 2014 John Wiley & Sons, Ltd.     

New potentially environmentally friendly copolymer of styrene and maleic acid—castor oil monoester

The maleic acid‐castor oil monoester (MACO) was synthesized and was used as monomer to synthesize a new potentially environmentally friendly copolymer of styrene and MACO (poly‐St/MACO) by suspension polymerization. Under the appropriate conditions, the poly‐St/MACO with yield of 81%, number average molecular weight of 44100 g/mol, and molecular weight distribution of 1.5 could be obtained. The chemical structures of the MACO and resulting copolymer were confirmed by Mass Spectrometry Infrared Spectroscopy and Nuclear Magnetic Resonance Spectroscopy H[1]. The results of thermogravimetric analysis and biodegradation test showed the poly‐St/MACO can be used as a new potentially environmentally friendly material with excellent thermal stability. Copyright © 2011 John Wiley & Sons, Ltd.     

Terpolymerization of methyl methacrylate, poly(ethylene glycol) methyl ether methacrylate or poly(ethylene glycol) ethyl ether methacrylate with methacrylic acid and sodium styrene sulfonate: determination of the reactivity ratios

Materials bearing ionic monomers were obtained through free radical terpolymerization of methyl methacrylate (MMA), poly(ethylene glycol) methyl ether methacrylate (PMEM) or poly(ethylene glycol) ethyl ether methacrylate (PEEM) with methacrylic acid (MA) and sodium styrene sulfonate (NaSS). The reactions were carried out in dimethyl sulfoxide using azobis(isobutyronitrile) as initiator. The reactivity ratios of the different couple of monomers were calculated according to the general copolymerization equation using the Finnemann-Ross, Kelen-Tüdos and Tidwell-Mortimer methods. The values of the reactivity ratios indicate that the different monomer units can be considered as randomly distributed along the chains for terpolymerizations of MMA, PMEM or PEEM with MA and NaSS. The average composition of the comonomers in the different terpolymers were calculated, showing a good agreement between the experimental and theoretical compositions. The instantaneous compositions are constant until about 70% of conversion. For higher conversions, the insertion of ionic monomers increases or decreases according to the system studied.     

Acrylonitrile–maleic anhydride copolymer membrane (II): effects of post‐treatment1

The effects of post‐treatment (including thermal treatment and base treatment) on the structure and performance of acrylonitrile–maleic anhydride (AN‐MA) copolymer membrane were investigated. The water flux decreased gradually (except the deviations when the temperature of thermal treatment was 50 °C or the time of thermal treatment was 50 min but rejection of bovine serum albumin increased slowly with increasing temperature or prolonging the time of thermal treatment. “The swelling effect of water in network” was proposed to explain the deviations. AN‐MA copolymer membrane is not resistant to a base. However, the performance of the membrane can be adjusted by treatment with a dilute base solution. Copyright © 2000 John Wiley & Sons, Ltd.