Polyaniline doped with different sulfonic acids by in situ doping polymerization

Doped polyaniline (PANI) was synthesized by an “in situ doping polymerization” method in the presence of different sulfonic acids, such as methanesulfonic acid (MSA), p‐methylbenzene sulfonic acid (MBSA), β‐naphthalenesulfonic acid (β‐NSA), α‐naphthalenesulfonic acid (α‐NSA), 1,5‐naphthalenedisulfonic acid (1,5‐NSA), and 2,4‐dinitronaphol‐7‐sulfonate acid (NONSA). Morphology, solubility in m‐cresol, and electrical properties of the doped PANI were measured with the variation of the molecular structure of the selected sulfonic acids. Granular morphology was obtained when the sulfonic acids without a naphthalene ring, such as MSA and MBSA, were used. Regular tubular morphology was obtained only when β‐NSA was used. The tubular morphology can be modified by changing the substitutes, the number, and location of sulfo‐group(SOH) on the naphthalene ring. These results indicated that naphthalene ring in the selected sulfonic acids plays an important role in forming the tubular morphology of the doped PANI by the “in situ doping polymerization” method. All resulting PANI salts were soluble in m‐cresol, with the solubility depending on the molecular structure of the selected dopants. Room‐temperature conductivity for the doped PANI ranges from 10⁻¹ to 10⁰S/cm. Temperature dependence of conductivity shows a semiconductor behavior, and it can be expressed by one dimenson Variable Range Hopping (VRH) model. 1 © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1277–1284, 1999     

盐酸掺杂聚苯胺的制备及性能研究

本文用溶液聚合法制备盐酸掺杂聚苯胺,测定了体系酸度对聚苯胺电导率的影响,及盐酸掺杂聚苯胺在不同条件下经过热处理后的电导率,采用TGA、XRD等方法,研究了热处理过程对聚苯胺结构的影响。结果表明,当热处理温度为90℃时,电导率高于初始值,当热处理温度高于100℃时,电导率开始下降,到达220℃时,电导率下降了约4个数量级。在氮气中聚苯胺电导率的衰减比空气中小,聚苯胺经热处理后在浓硫酸中的溶解性会明显降低。本文还探讨了去掺杂、氧化和化学交联等盐酸掺杂聚苯胺的热降解机理。     

In situ doping polymerization of polyaniline microtubules in the presence of β‐naphthalenesulfonic acid

Conducting microtubules of Polyaniline (PANI) were synthesized for the first time by the “in situ doping polymerization” method in the presence of β‐naphthal‐ enesulfonic acid (NSA) as dopant. Different doping methods, such as “immerse doping” and “grind doping,” and different synthetic conditions, such as molar ratio of aniline (An) to NSA (An/NSA), concentration of NSA in the polymerization media, reaction temperature, and time were investigated to understand the formation of microtubules. It was found that the PANI–NSA microtubules can be formed only by the “in situ doping polymerization” method, and the above synthetic conditions strongly affect the formation of the PANI–NSA microtubules, especially the molar ratio of An to NSA. An optimal condition was found under which tubules with 1–3 μm in diameter and 10–50 μm in length were obtained. The morphology of PANI–NSA tubules was proved by SEM and TEM, and their backbone structure was characterized by FTIR, UV‐VIS, XPS, and X‐ray diffraction. Results of these measurements showed that the molecular structures of the resulted PANI–NSA microtubules were identical to that of PANI–HCl synthesized by conventional method. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 151–157, 1999     

In situ polymerization and reduction to fabricate gold nanoparticle‐incorporated polyaniline as supercapacitor electrode materials

Nanocomposites of gold nanoparticles and polyaniline are synthesized by using HAuCl₄ and ammonium peroxydisulfate as the co‐oxidant involving in situ polymerization of aniline and in situ reduction of HAuCl₄. Through these in situ methods, the synthesized Au nanoparticles of ca. 20 nm embedded tightly and dispersed uniformly in polyaniline backbone. With the Au content in composite increasing from 4.20 to 24.72 wt.%, the specific capacitance of the materials first increased from 334 to 392 F g⁻¹ and then decreased to 298 F g⁻¹. Based on the real content of PANI in composite material, the highest specific capacitance is calculated to be 485 F g⁻¹ at the Au amount of 19.15 wt.%, which remains 55.6% after 5000 cycles at the current density of 2 A g⁻¹. Finally, the asymmetric supercapacitor of AuNP/PANI||AC and the symmetric supercapacitor of AuNP/PANI||AuNP/PANI are assembled. The asymmetric supercapacitor device shows a better electrochemical performance, which delivers the maximum energy density of 7.71 Wh kg⁻¹ with power density of 125 W kg⁻¹ and maximum power density of 2500 W kg⁻¹ with the energy density of 5.35 Wh kg⁻¹.     

Preparation of processable polyaniline doped and complexed with anionic surfactant

Processable polyaniline doped and complexed with dodecylbenzenesulfonic acid was obtained by one-step micellar chemical polymerization of aniline in the presence of dodecylbenzenesulfonic acid. Homogeneous transparent suspension could be made by dispersing processable polyaniline in m-cresol without any precipitation. Polyaniline composite film blended with polymethylmethacrylate (PMMA) exhibits relatively high levels of conductivity at low volume fractions of the polyaniline, while keeping good mechanical properties, equivalent to those of the PMMA. © 1998 John Wiley & Sons, Ltd.     

Conduction behavior of doped polyaniline films at high current density regime

The conduction behavior at high current density at room temperature and above of polyaniline (PANI) films doped with HCl and camphor sulfonic acid (HCSA), respectively, is reported. It is found that the current density deviates strongly from the linear relation with the electric field in high current density region, and a saturation of the current density is observed. The maximum current density J_m seems to be proportional to the conductivity of the sample and hence, for PANI doped with HCl, J_m is about 200 A/cm^2, whereas for HCSA doped samples, J_m can reach more than 1,200 A/cm². The saturation of current density is interpreted as being caused by space charge accumulation at the insulating barrier regions and a dedoping effect in the conduction domains due to the detraping of the ions under high fields. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2845–2850, 1999     

Structure and properties of plasma-polymerized thin films of polyaniline

Plasma polymerization of aniline and in-situ doping of polvaniline with iodine was carried out using radio frequency glow discharge. Thin films of polyaniline were deposited on platinum and glass. The infrared spectrum shows that the aromatic ring is retained under the plasma conditions. The electrical conductivity measurements indicate that the conductivity increases by more than seven orders of magnitude when the polyaniline is doped by iodine. The scanning electron microscopic studies reveal the formation of irregular pentagons on glass substrate while on platinum, polvaniline forms a fibrillar network. In both the cases a continuous film is obtained.     

Synthesis of core‐shell silver–polyaniline nanocomposites by gamma radiolysis method

Core‐shell silver (Ag)–polyaniline (PAni) nanocomposites have been synthesized by the in‐situ gamma radiation‐induced chemical polymerization method. Aqueous solution of aniline, a free‐radical oxidant, and/or silver metal salt were irradiated by γ‐rays. Reduction of the silver salt in aqueous aniline leads to the formation of silver nanoparticles which in turn catalyze oxidation of aniline to polyaniline. The resultant Ag‐PAni nanocomposites were characterized by using different spectroscopy analyses like X‐ray photoelectron, UV–visible, and infrared spectroscopy. The optical absorption bands revealed that the bands at about 400 nm are due to the presence of nanosilver and the blue‐shifted peak at ～ 555 nm is due to the presence of metallic silver within the PAni matrix. X‐ray diffraction pattern clearly indicates the broad amorphous polymer and the sharp metal peaks. Scanning electron microscopy and transmission electron microscopy of the nanocomposite showed a uniform size distribution with spherical and granular morphology. Thermogravimetric analysis revealed that the composites have a higher degradation temperature than polyaniline alone. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5741–5747, 2007     

Synthesis and characterization of polyaniline doped with organic acids

Spectroscopic [UV–visible and Fourier transform IR (FTIR)] and thermal properties of chemically synthesized polyanilines are found to be affected by varying the protonation media (acetic, citric, oxalic, and tartaric acid). The optical spectra show the presence of a greater fraction of fully oxidized insulating pernigraniline phase in polyaniline doped with acetic acid. In contrast, the selectivity in the formation of the conducting phase is higher in oxalic acid as a protonic acid media. The FTIR spectra of these polymers reveal a higher ratio of the relative intensities of the quinoid to benzenoid ring modes in acetic acid doped polyaniline. Scanning electron micrographs revealed a sponge‐like structure derived from the aggregation of the small granules in acetic acid and oxalic acid doped polyaniline. A three‐step decomposition pattern is observed in all the polymers, regardless of the protonic acid used for the doping. The second step loss related to the loss of dopant is found to be higher in the oxalic acid doped polymer. In accordance with these results the conductivity is also found to be higher in oxalic acid doped material. The temperature dependent conductivity measurements show the thermal activated behavior in all the polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2043–2049, 2004     

Optical sensing of HCl with phenol red doped sol-gels

A dye doped sol-gel for the sensing of hydrochloric acid in solution and/or gaseous phase is described. The sol-gel is obtained by acidic hydrolysis of tetraethoxysilane (TEOS) and phenyltriethoxysilane (Ph-TriEOS) in the presence of phenol red (PR) and further spin-coating onto glass slides. The sensitive response is based on an increase of the absorption band at 510 nm of phenol red entrapped in the sol-gel casting when exposed to HCl solution or gas, due to protonation of the dye. The detection limit of the sol-gel response to moisturized gaseous HCl is below 12 ppm, and its response to HCl in solution falls in the range of 0.01-6 M. The sol-gel coating has a response time of less than 40 s in steady-state, and life-time of more than a year. Weak acids such as acetic acid, benzoic acid, salicylate acid, citrate acid, and carbonic acid do not interfere the response. The responses in acid solutions are completely reversible. In the gaseous phase, response of HCl appears to be moisture sensitive.     

Preparation and characterization of polyaniline with high electrical conductivity

In the present paper, polyaniline (PANI) was polymerized by ammonium persulphate using a chemically oxidative process under mild tempertures ranging from ?5–20°C. Electrical conductivity of as synthesized PANI got enhanced gradually owing to the increase in molecular weight and crystallinity with decrease in synthesis temperature. Extraction with tetrahydrofuran (THF) was employed as the purification method of emeraldine base (EB) to enhance the electrical conductivity of PANI effectively attributed to the removal of the low molecular weight fractions and defective molecular chains. Methanesulfonic acid (MSA) was used to dope EB due to its strong acidity and small molecular size, and the amount of dopant versus EB was also optimized. Using a novel “synergistic doping” process with m‐cresol, electrical conductivity of PANI is further enhanced owing to more regular molecular chains which resulted in better interchain charge carriers' conduction. The emeraldine salts obtained finally have high electrical conductivity reaching up to 32.5 S cm^?1, which is much higher than that of the conventionally synthesized sample reported previously. Copyright © 2008 John Wiley & Sons, Ltd.     

A comparative study on the reaction mechanisms of Cp2MH2 (M = Cr,Mo, W) with HBF4

The reaction mechanisms of group 6 transition metal dihydride complexes, Cp₂MH₂ (M = Cr, Mo, and W), and HBF₄ were studied using M06‐L density functional theory. The chemical bond changes along the reaction pathway are analyzed by the topological analysis of electron density. The calculated results show that the interactions between the H atom of HBF₄ and Cp₂MH₂ are stronger than those between Cp₂MH₂ and BF₃; additionally, due to the low energy barriers in the subsequent reaction, all the title reactions can occur easily, and the yield rates of the Cp₂MH₂ + HBF₄ reactions are high. For M = Cr and Mo, the [Cp₂MH₃]⁺ in the product Cp₂MH₃·BF₄ is in the nonclassic dihydrogen‐hydride form ([Cp₂M(η²‐H₂)H]⁺). [Cp₂CrH₃]⁺ and [Cp₂MoH₃]⁺are unstable, and H₂ can be easily liberated from them. For M = W, the final product is Cp₂WH₃·BF₄, and [Cp₂WH₃]⁺ is stable in the classic trihydride form.     

Wide-range regulation of polyaniline conduction by interphase doping of a polyaniline film

The not-sufficient-enough conductance of semioxidized protonated polyaniline (PANI) is usually attributed to the presence of ordered quasi-metallic domains surrounded by a poorly conducting amorphous phase. The paper presents experimental results testifying to the existence, in semioxidized PANI, of multilevel redox heterogeneity that crucially effects the conductance magnitude in view of specific topology at which higher-oxidized (conducting) domains are surrounded by less oxidized (poorly conducting) domains and because the PANI conduction is extremely sensitive to the oxidation degree. It is shown experimentally that the interphase doping with metals and degenerate semiconductors of a semioxidized salt of PANI and poly(2-acrylamide-2-methyl-1-propanesulfonic acid) (PAMPSA) with a 1: 2 ratio between PANI and PAMPSA raises the PANI-PAMPSA conductivity by 3–8 orders of magnitude due to the formation near the interface of thin layers whose conductance depends on the work function of the material in contact with PANI-PAMPSA and in extreme cases substantially exceeds the conductance of gold and copper at room temperature.     

On the influence of electron energy on iodine‐doped polyaniline formation by plasma polymerization

The influences that both electron energy and density of a plasma bear on thin film formation are examined in the case of iodine‐doped polyaniline polymerization. The plasma was produced by means of 13.5‐MHz radiofrequency–generated glow discharges in low‐pressure (ca. 10⁻² mbar) air between electrodes. Four representative inner regions of the reactor were selected according to the electron incidence. Given the uneven energy distribution found on the inside of this kind of reactors, variations in the polymer structure formed in the presence of iodine were found and studied by elemental analysis, thermogravimetry, infrared spectroscopy, and X‐ray diffraction. The results indicate that the electric conductivity of polyaniline by plasma is a function of the iodine content and that such content is a function of the combined conditions of both reactor and plasma. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 175–183, 2001     

Synthesis and Characterization of Self-Assembled V2O5 Mesostructures Intercalated by Polyaniline

A new nanocomposite of vanadium pentoxide (V2O5) and polyaniline (PANI) were synthesized by in situ oxidative polymerization/intercalation on V2O5 powder at room temperature. The reaction was facile and topotactic, forming polyaniline as the emeraldine salt. It was indicated that V2O5 itself can catalyze the oxidative polymerization of aniline and that layered structure could make aniline intercalate into the V2O5 framework. It makes the in situ polymerization feasible to occur in the layer of V2O5 structure. XRD results showed PANI/V2O5 nanocomposite possessed lamellar mesostructure, which was determined by an X-ray diffraction peak at 6.5° and SEM photograph. And FT-IR spectrum suggested that there was interaction between PANI and V2O5. The hybrid had better thermal stability in N2 and air ambience.     

Charge transport in polyaniline doped with 3-nitro-1,2,4-triazol-5(4H)-one

Polyaniline (PANI) base was protonated in aqueous solutions of an organic acid, 3-nitro-1,2,4-triazol-5(4H)-one (NTO). The temperature dependence of DC conductivity of PANI-NTO seems to correspond to the theory of variable range hopping (VRH) in three dimensions. The frequency dependence of AC conductivity also reflects the hopping nature of mobile charges. The activation energy for the polymers with protonation degree above 0.12 remains constant with increasing dopant concentration and DC conductivity. The value of this constant may correspond to the energy needed for the ionization of dopant counterion. The fit of the electric relaxation function to the stretched exponential function ϕ(t) = exp[−(t/τ)^β] gives the stretch parameter β about 0.35, which shows that the distribution of relaxation times is broad and indicates a high inhomogeneity in the distribution of a dopant.     

Study of vibrational spectra of polyaniline doped with sulfuric acid and phosphoric acid

Vibrational spectra of insulator emeraldine base (EB) form of polyaniline and electrical conductive sulfuric acid-and phosphoric acid-doped emeraldine salts (ES) were studied in the region of 4000-400 cm⁻¹ at ambient temperature by Fourier transform infrared spectroscopy. Infrared transmittance spectra of EB and ES were investigated to understand the bonding behavior of different organic and inorganic groups present in the polymeric chains and their structural variations on protonation by sulfate or phosphate ion inclusion in the polymer salt network. These studies revealed the para-coupling of deformed disubstituted benzenoid (B) and quinoid (Q) rings with ends capped predominantly by (B4Q1) units. The deformation of B and Q rings was confirmed by the appearance of many weak bands, very weak bands, and satellite structures in strong transmittance peaks of polymeric chain-constituting groups. Protonation takes place at the nitrogen sites of Q rings and forms semiquinone radical ions in ES. The vibrational bands pertaining to B rings, Q rings, B4Q1 units, semiquinone segment, sulfate ions, and phosphate ions were observed and assigned from these measurements. The shift in peak position of some bands with gain or loss in intensity and appearance of some new bands were observed in sulfuric acid-and phosphoric acid-doped ES spectra. These variations are attributed to the formation of new structural groups in ES on protonation and a change in crystalline field by sulfate and phosphate ion doping for crosslinking the polymeric chains.     

Electrocatalytic synthesis of polyaniline on non-noble metal electrodes

Electrochemical synthesis (ES) of polyaniline (PAn) at the surface covered by an oxide film is realized at a significantly higher voltage than is needed for the formation of a nonoveroxidized polymer. The involvement of catalytic amounts of the salts of transition metals in ES of PAn essentially facilitates the process at Ti, Ta, Pb, Al and stainless steel electrodes. IrCI²⁻₆ anion was found to be an effective catalyst. During ES, IrCI²⁻₆ forms a complex with aniline, where Ir^IY oxidizes aniline to a radical cation. The formation of radical cation is a limiting stage ES PAn. It is realized in a moment in the presence of IrCI²⁻₆, thus providing a significant decrease of the induction period at a potentiostatic synthesis and the lowering of a working potential at a galvanostatic synthesis. It is shown that the composition of the complex includes Ir^III and 2 aniline molecules, which form a paramagnetic dimer inside a coordination sphere. © 1997 John Wiley & Sons, Ltd.     

Detection of acetaminophen using cyclic voltammetry on MnFe2O4/polyaniline

A novel sensing material, MnFe₂O₄/polyaniline (PANI), was fabricated by doping PANI to MnFe₂O₄ on a modified glassy carbon electrode (GCE). This sensing material was characterized using X‐ray diffraction (XRD), scanning electron microscopy (SEM), and high‐resolution transmission electron microscopy (HR‐TEM). Using a cyclic voltammetry electrochemical‐sensing method, we tested MnFe₂O₄/PANI, and an acetaminophen concentration of 0.0625–5 mM was recorded. Furthermore, the sensor responses were 2.05–22.44. The detection limit was 2.23 × 10^?7 M. Strong selectivity was observed for MnFe₂O₄/PANI, which is a possible sensing mechanism.     

四种方法合成单一手性聚苯胺纳米纤维研究

以过硫酸铵或2,3-二氯-5,6-二氰基-1,4-苯醌（DDQ）为氧化剂,单一手性樟脑磺酸作为诱导酸及掺杂剂,在有机溶剂、水-有机溶剂和水溶剂体系中,采用四种不同方法分别进行了单一手性聚苯胺纳米纤维合成研究。通过扫描电子显微镜（SEM）、紫外可见光谱（UV-VIS）、X射线衍射（XRD）和圆二色谱（CD）等手段对自组装法、界面聚合法、低聚物辅助法与二次掺杂法等四种方法制备得到聚苯胺纳米纤维的形貌、结构及光学活性进行表征,对比分析后发现四种方法合成的掺杂态聚苯胺纳米纤维形貌、结构相似,但溶剂体系会影响最终产物的光学活性：水溶剂、有机溶剂体系中,得到的聚苯胺纳米纤维光学活性相反。