Grafting of polymers onto and/or from silica surface during the polymerization of vinyl monomers in the presence of γ‐ray‐irradiated silica

The effects of radicals on silica surface, which were formed by γ‐ray irradiation, on the polymerization of vinyl monomers were investigated. It was found that the polymerization of styrene was remarkably retarded in the presence of γ‐ray‐irradiated silica above 60 °C, at which thermal polymerization of styrene is readily initiated. During the polymerization, a part of polystyrene formed was grafted onto the silica surface but percentage of grafting was very small. On the other hand, no retardation of the polymerization of styrene was observed in the presence of γ‐ray‐irradiated silica below 50 °C; the polymerization tends to accelerate and polystyrene was grafted onto the silica surface. Poly(vinyl acetate) and poly(methyl methacrylate) (MMA) were also grafted onto the surface during the polymerization in the presence of γ‐ray‐irradiated silica. The grafting of polymers onto the silica surface was confirmed by thermal decomposition GC‐MS. It was considered that at lower temperature, the grafting based on the propagation of polystyrene from surface radical (“grafting from” mechanism) preferentially proceeded. On the contrary, at higher temperature, the coupling reaction of propagating polymer radicals with surface radicals (“grafting onto” mechanism) proceeded to give relatively higher molecular weight polymer‐grafted silica. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2972–2979, 2006     

Hydroperoxide formation in irradiated polyethylene

Spectroscopic analysis for hydroperoxide in irradiated ultrahigh molecular weight polyethylene, on the basis of the formation of a nitrate derivative after exposure to dilute nitric oxide, is examined. Hydroperoxide is found to be an important intermediate in the oxidation of polyethylene and is believed to result from hydrogen abstraction reactions by peroxy radicals in a polyethylene matrix. During γ irradiation in air, the rates of bimolecular combination of peroxy radicals on the surface to form ketones or hydrogen abstraction to form hydroperoxides are similar. However, as a result of bimolecular combination, the concentration of peroxy radicals decreases. After irradiation and storage in ambient air, isolated peroxy radicals below the polymer surface induce a slow chain reaction leading to a long-term increase in hydroperoxides and carbonyls. Differences in hydroperoxide and oxygen content for samples irradiated in air or vacuum are primarily confined to or near the surface. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3309–3316, 1999     

Radiooxidation of fluoropolymers: Identification of oxidation products

Radiation effects on fluoropolymers induced by high‐energy irradiation were investigated. Poly(fluorovinylidene‐co‐hexafluoropropylene) [P(VDF‐HFP)] films were irradiated with γ rays in air. Peroxy radicals formed by irradiation in the presence of oxygen were partially converted into more stable products such as hydroperoxides, alcohols, and acids. These oxidation products were identified by Fourier transform infrared spectroscopy. Specific chemical treatments were carried out to identify and separate overlapping absorption bands. Model compounds were also used. On the basis of the results, a mechanism of degradation for γ‐irradiated P(VDF‐HFP) is proposed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1509–1517, 2003     

Structure,thermal stability,and photocrosslinking characterization of HDPE/LDH nanocomposites synthesized by melt‐intercalation

Structure, thermal properties, and influence of layered double hydroxide (LDH) fillers on photocrosslinking behavior of high‐density polyethylene (HDPE)/LDH nanocomposites have been studied in the present article. The X‐ray diffraction and transmission electron microscopy analysis demonstrate that the completely exfoliated HDPE/LDH nanocomposites can be obtained by controlling the organomodified LDH loading via melt‐intercalation. The data from the thermogravimetric analysis show that the HDPE/LDH nanocomposites have much higher thermal stability than HDPE sample. When the 50% weight loss was selected as a comparison point, the decomposition temperature of HDPE/LDH sample with 5 wt % LDH loading is ～40 °C higher than that of HDPE sample. The effects of UV‐irradiation on the HDPE/LDH nanocomposites show that the photoinitiated crosslinking can destroy the completely exfoliated structure to form the partially exfoliated structure, which decreased the thermal stability of the nanocomposites. However, the thermal stability of photocrosslinked samples can increase with increasing the UV‐irradiation time. The effect of LDH loading on the gel content of UV‐irradiated nanocomposites shows that the LDH materials can greatly absorb the UV irradiation and thus decrease the crosslinking efficiency. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3165–3172, 2006     

Patterned immobilization of biomolecules by using ion irradiation‐induced graft polymerization

A new method for biomolecular patterning based on ion irradiation‐induced graft polymerization was demonstrated in this study. Ion irradiation on a polymer surface resulted in the formation of active species, which was further used for surface‐initiated graft polymerization of acrylic acid. The results of the grafting study revealed that the surface graft polymerization using 20 vol % of acrylic acid on the poly(tetrafluoroethylene) (PTFE) film irradiated at the fluence of 1 × 10¹⁵ ions/cm² for 12 h was the optimum graft polymerization condition to achieve the maximum grafting degree. The results of the fluorescence microscopy also revealed that the optimum fluence to achieve the maximum fluorescence intensity was 1 × 10¹⁵ ions/cm². The grafting of acrylic acid on the PTFE surfaces was confirmed by a fluorescence labeling method. The grafted PTFE films were used for the immobilization of amine‐functionalized p‐DNA, followed by hybridization with fluorescently tagged c‐DNA. Biotin‐amine was also immobilized on the acrylic acid grafted PTFE surfaces. Successful biotin‐specific binding of streptavidin further confirmed the potential of this strategy for patterning of various biomolecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6124–6134, 2009     

The thermal desorption mass spectra of polytetrafluoroethylene modified under the action of radiation at elevated temperatures

The products of the pyrolysis of polytetrafluoroethylene (PTFE) in a vacuum modified under the action of gamma irradiation in the molten state were studied mass spectrometrically at various temperatures. Radiation modification was found to cause the appearance of an additional stage of the thermal decomposition of PTFE at decreased temperatures compared with not irradiated PTFE. The chemical composition of the gas components of thermal decomposition substantially changes after the irradiation of PTFE, which increases the molecular weight of decomposition products. A comparison with the results of an additional study of the thermal decomposition of tetrafluoroethylene copolymer with hexafluoropropylene is evidence of the formation of side CF₃ groups in PTFE under irradiation. Data on the composition of gaseous products of PTFE radiolysis under gamma irradiation were obtained.     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Surface studies of ultra‐high molecular weight polyethylene irradiated with high‐energy pulsed electron beams in air

Ultra‐high molecular weight polyethylene (UHMWPE) was irradiated in air with high‐energy (9 MeV), pulsed electron beams to doses ranging from 2.5 to 100 Mrad and subsequently heat treated at 120°C for a time period of 120 min. Surface characterization of the target side of irradiated UHMWPE samples was carried out both before and after the heat treatment by means of attenuated total reflection Fourier‐transform infrared (FTIR/ATR) spectroscopy and microhardness measurement. The obtained results provided further evidence supporting our earlier observation (Tretinnikov, O. N.; Ogata, S.; Ikada, Y. Polymer 1998, 39, 6115) that thermal decomposition of hydroperoxides formed upon irradiation of UHMWPE with high‐energy, pulsed electron beams in air leads to surface crosslinking, and the subsequent surface hardening of the irradiated polymer. Importantly, we found that this phenomenon has the highest contribution to the surface hardness enhancement of the polymer when the radiation dose is in the range of 10–30 Mrad. In addition, we found that this irradiation and subsequent heat treatment of UHMWPE in air does not lead to formation of carbonyl‐containing products unless the radiation dose exceeds 20 Mrad. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1503–1512, 1999     

Rotational vibration of poly(tetrafluoroethylene) chains by the electron spin resonance method

Temperature‐dependent electron spin resonance spectra of main‐chain free radicals, ? CF₂(β)? C · F(α)? CF₂(β)? , in poly(tetrafluoroethylene) (PTFE) were analyzed by the change in the hyperfine splitting due to β‐fluorines, which was a decreasing function of the observation temperature. The results were interpreted in terms of the rotational vibration around the C_α? C_β bond. The amplitude of the vibration was estimated on the assumption of its harmonic oscillation. The vibration of the PTFE chain was found to have a large amplitude in comparison with that of a polyethylene chain in single crystals. The vibration of the large amplitude was caused by a weak interchain interaction in the PTFE matrices. The amplitude of the vibration in crosslinked PTFE was much larger than that in noncrosslinked PTFE. This result indicated that the free radicals in crosslinked PTFE were trapped in the amorphous region, which had the disordered sites of crosslinking, whereas the free radicals in noncrosslinked PTFE were mainly trapped in the paracrystalline region. The decay reaction of the free radicals in the PTFE matrices was also related to the heterogeneity in the structure and the rotational vibration. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1539–1547, 2004     

Synthesis and thermal dissociation of polymers having hemiacetal ester moieties

Polymers having hemiacetal ester moieties in the side chain were synthesized and their thermal dissociation was examined. 1‐Alkoxyethyl methacrylates (1) were synthesized from methacrylic acid with alkyl vinyl ethers and their radical copolymerizations with butyl methacrylate were carried out at 80°C for 6.5 h using AIBN as an initiator to afford the corresponding copolymers having the hemiacetal ester moieties in the side chain. The hemiacetal ester moieties in the copolymers thermally converted to carboxyl groups with elimination of the corresponding vinyl ethers. The thermal dissociation of the hemiacetal ester moieties in the side chain obeyed first‐order kinetics at 140°C, and their reactivities were in the following order: 1‐(tert‐butoxy)ethyl > 1‐isopropoxyethyl > 1‐ethoxyethyl > 1‐butoxyethyl ester. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 609–614, 1999     

Radiation effects on the thermal degradation of poly(vinyl chloride) and poly(vinyl alcohol)

Radiation effects on the formation of conjugated double bonds in the thermal degradation of poly(vinyl chloride) (PVC) and poly(vinyl alcohol) (PVA) were investigated. Thin films of PVC and PVA were either irradiated with γ-rays at ambient temperature (pre-irradiation) and then subjected to thermal treatment, or irradiated at elevated temperatures (in situ irradiation). An extensive enhancement of the thermal degradation was observed for the pre-irradiation of the PVC films, which was more effective than the effect of the in situ irradiation at the same absorption dose. For the PVA degradation, however, the effect of the in situ irradiation was larger than that of the pre-irradiation. The results were explained and related mechanisms were discussed based on radiation-induced chemical reactions and their individual contributions to the thermal degradation behaviors of the two polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3089–3095, 1998     

Photocrosslinking system based on a poly(vinyl phenol)/thermally degradable diepoxy crosslinker blend

Photocrosslinkable systems with thermally cleavable properties based on blends of poly(vinyl phenol) (PVP) and diepoxides were investigated. Thermally cleavable diepoxides as crosslinkers were prepared and characterized. As a thermally cleavable linkage, a tertiary ester moiety was incorporated into the crosslinker molecule. PVP/crosslinker blended films containing photoacid generators (PAGs) became insoluble in solvents after UV irradiation and subsequent post‐exposure‐bake (PEB) treatment. With a rise in the PEB temperature, the insoluble fraction of the irradiated films increased, passed through a maximum value, decreased, and increased again at elevated baking temperatures. The insolubilization profiles of the irradiated films were complicated and strongly dependent on the type of PAG used, the structure of the crosslinkers, and the PVP/crosslinker ratio. A mechanism for the thermal degradation was studied with Fourier transform infrared spectroscopy. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3055–3062, 2002     

The grafting of acrylamide onto poly(ε‐caprolactone) and poly(1,5‐dioxepan‐2‐one) using electron beam preirradiation. III. The grafting and in vitro degradation of chemically crosslinked poly(1,5‐dioxepan‐2‐one)

Acrylamide was graft polymerized onto the surface of a chemically crosslinked and amorphous biodegradable polyester, poly(1,5‐dioxepan‐2‐one). Electron beam irradiation at a dose of 5 Mrad was used to generate the initiating species in the polyester. The degradation behavior in vitro at pH 7.4 and 37°C in a phosphate buffer solution was studied for untreated, irradiated, and acrylamide‐grafted polymer. Differences in weight loss performance were observed between virgin and treated polymers. The acrylamide‐grafted poly(1,5‐dioxepan‐2‐one) was totally degraded after 43 weeks as compared to 48 weeks for the irradiated and 55 weeks for the virgin polymer. On the other hand, the treated polymers showed a higher resistance to degradation in terms of weight loss during the intermediate part of the degradation, i.e., between about 5 and 35 weeks. After this period, the irradiated and particularly the acrylamide grafted poly(1,5‐dioxepan‐2‐one) degraded much more rapidly than the virgin polymer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1659–1663, 1999     

Phase behavior of crystalline blends of poly(tetrafluoroethylene) and of random fluorinated copolymers of tetrafluoroethylene

In the present article, we investigate by differential scanning calorimetry (DSC) the thermal behavior (melting, crystallization, and crystal–crystal transitions) far from equilibrium of blends constituted of two crystalline polymers. In particular, the following blends are examined: PTFE–PFMVE, PTFE–FEP, and FEP–PFMVE where PTFE is poly(tetrafluoroethylene), PFMVE is poly(tetrafluoroethylene‐co‐perfluoromethylvinylether), and FEP is poly(tetrafluoroethylene‐co‐hexafluoropropylene). The two last ones are random tetrafluoroethylene copolymers with small amounts of comonomer. Our results indicate that, under the experimental investigated conditions, the blends containing PTFE do not give cocrystallization on cooling from the melt, although under very rapid crystallization conditions, quenching, the presence of the copolymer would seem to slightly influence PTFE crystallization (lower peak temperatures are observed for the crystalline transitions and the melting with respect to those of the neat homopolymer). The behavior of the FEP–PFMVE blend is completely different; in fact, our results indicate the occurrence of cocrystallization, then miscibility in the crystalline phase, for almost all compositions and all investigated experimental conditions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 679–689, 1999     

Photochemical modification of polymer surface by the pendant photobase generator containing oxime‐urethane groups and its application to an image‐recording material

Copolymers containing oxime‐urethane groups were prepared by the copolymerization of methyl methacrylate and benzophenoneoximinocarbonylaminoethyl methacrylate (BCM), and their photochemical properties were examined from the UV and IR absorption spectral changes. The decomposed fraction of oxime‐urethane groups in the copolymer increased with irradiation time, but it decreased with the content of BCM units in the copolymer. Changes of the surface properties of the copolymer film on irradiation were studied by measurements of the contact angle and dyeing with an acid dye. The surface of the copolymer film changed to become more hydrophilic upon irradiation with 254 nm of UV light. After the irradiated copolymer films were treated with HCl or methanol, changes of the contact angle of water on irradiation were compared. The copolymer film was dyed by acid dyes after treatment of the irradiated film with HCl. The degree of dyeing increased with irradiation time and BCM units in the copolymer, but it was unaffected by the film thickness. Various colors were developed on the irradiated area depending on the acid dye as the developer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1200–1207, 2002     

Image formation by dyeing of copolymers bearing photogenerated acid and base groups with dye bath containing acid and basic dyes

Copolymers bearing photoacid generating groups and/or photobase generating groups were dyed after UV irradiation with a dye bath containing both an acid dye and a basic dye. Acetophenone O‐acryloyloxime (AAPO) was used as a monomer bearing acyloxyimino (AOI) group that generates a primary amino group upon irradiation, which is followed by hydrolysis. Phenacylsulfonylstyrene (PSSt) and 1,2,3,4‐tetrahydronaphthylideneamino p‐styrenesulfonate (NISS) were chosen as monomers having β‐keto sulfone (β‐KS) and iminosulfonate (IS) groups, respectively, which yielded acid groups when irradiated. Copolymers of AAPO and methyl methacrylate (MMA) were dyed with only the acid dye, and those of PSSt or NISS were dyed with only the basic dye after irradiation. AAPO‐PSSt‐MMA films became dyeable with the acid dye when irradiated for a short time and with the basic dye with further irradiation. However, AAPO‐NISS‐MMA copolymers showed the reverse dyeing behavior. IR spectra revealed that AOI groups were photochemically decomposed prior to the β‐KS groups for AAPO‐PSSt‐MMA, and AOI and IS groups decomposed simultaneously for AAPO‐NISS‐MMA. These results suggested the possibility of adsorption of different ionic dyes on the films by a change of irradiation time; in fact, color patterns could be obtained in a single staining process using the dye bath. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3043–3051, 2000     

ESR study on free radicals trapped in crosslinked polytetrafluoroethylene (PTFE)

Free radicals in crosslinked PTFE which formed by ⁶⁰Co γ-rays irradiaion at 77 K and at room temperature were studied by electron spin resonance (ESR) spectroscopy. The crosslinked PTFE specimens with different crosslinking density were prepared by electron beam irradiation in the molten state. The ESR spectra observed in the irradiated crosslinked PTFE are much different from those in non-crosslinked PTFE (virgin); a broad singlet component increases with increasing the crosslinking density, G-value of radicals is much higher in crosslinked PTFE than in non-crosslinked one. Free radicals related to the broad component are trapped in the non-crystalline region of crosslinked PTFE and rather stable at room temperature, whereas radicals trapped in amorphous non-crosslinked PTFE are unstable at room temperature. It is thought that most of free radicals trapped in the crosslinked PTFE are formed in the crosslinked amorphous region. The trapped radicals decays around 383 K (110°C) due to the molecular motion of -relaxation.     

Controlled radical polymerization of anthracene‐containing methacrylate copolymers for stimuli‐responsive materials

Novel reversible networks utilizing photodimerization of crosslinkable anthracene groups and thermal dissociation were investigated. Reversible addition‐fragmentation chain transfer polymerization yielded well‐defined copolymers with 9‐anthrylmethyl methacrylate (AMMA) and other alkyl methacrylates such as methyl methacrylate (MMA) and 2‐ethylhexyl methacrylate (EHMA) having different AMMA compositions. Well‐controlled block copolymerization of AMMA and alkyl methacrylates was also successfully accomplished using a trithiocarbonate‐terminated poly(alkyl methacrylate) macro‐chain transfer agent. The anthracene‐containing copolymers showed reversibility via crosslinking based on photodimerization with ultraviolet irradiation and subsequent thermal dissociation. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2302–2311     

Large enhancement of the ionic conductivity in an electron‐beam‐irradiated [poly(ethylene glycol)]xLiClO4 solid polymer electrolyte

The effect of electron‐beam (4–8 MeV) irradiation on the ionic conductivity of a solid polymer electrolyte, poly(ethylene glycol) complexed with LiClO₄, was studied. A large enhancement of the conductivity of nearly two orders of magnitude was observed for the highest dose of irradiation (15 kGy) used. The samples were characterized with differential scanning calorimetry, matrix‐assisted laser desorption/ionization, and electron spin resonance spectroscopy. Although no free radicals were present in the irradiated samples, a decrease in the glass‐transition temperature and an increase in the amorphous fraction were observed. Even though pure poly(ethylene glycol) underwent considerable fragmentation, unexpectedly, no significant fragmentation was observed in the polymer–salt complexes. The enhancement of the conductivity was attributed to an increase in the amorphous fraction of the systems and also to an increase in the flexibility of the polymer chains due to the irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1299–1311, 2004     

Pulsed‐laser–deposited and plasma‐polymerized polytetrafluoroethylene (PTFE)‐like thin films: A comparative study on PTFE‐specific properties

Glass‐like and structural first‐order phase transitions are investigated in polytetrafluoroethylene (PTFE) foils and PTFE‐like films prepared by pulsed‐laser deposition (PLD) and plasma polymerization (PP). A structural comparison of the investigated polymers is performed by infrared spectroscopy and dielectric dilatometry. It is shown that dielectric dilatometry (the measurement of the susceptance vs. temperature) provides a simple and elegant means for detecting volumetric transitions in thin nonpolar polymer films. In conventional PTFE foils, the known glass‐like and structural first‐order phase transitions are identified. The structure of pulsed‐laser deposited PTFE strongly depends on the target material, ranging from highly crystalline films showing only structural phase transitions to films strongly deviating from PTFE foils, with structural characteristics comparable to plasma‐polymerized fluorocarbons. The dielectric loss of the highly crystalline PLD films compares favorably with conventional PTFE foils, making the films attractive for new applications in miniature electret devices. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2115–2125, 1999