Catalytic chain transfer for molecular weight control in the emulsion homo- and copolymerizations of methyl methacrylate and butyl methacrylate

The behavior of catalytic chain transfer in semi-batch emulsion polymerization has been studied for two monomers, viz, methyl and n-butyl methacrylate. Two different catalytic chain transfer reagents were used with different water solubilities: cobaloxime boron fluoride (COBF), which was found to partition approximately equally between organic and aqueous phases, and tetra-phenyl cobaloxime boron fluoride (COPhBF), which was found to reside predominantly in the organic phase. The difference in hydrophilicity between the two transfer agents was found to affect the polymerization mechanism. COBF exhibited superior transfer behavior in all cases, whereas the restricted mobility of the COPhBF had a deleterious effect on the efficiency of the transfer mechanism. The best results were achieved under monomer flooded conditions using COBF. MALDI-TOF mass spectrometry analysis shows catalytic chain transfer to be the dominant mechanism initiating and stopping chain growth as none of the chains appear to have initiator fragment end groups. Analysis of copolymers by MALDI-TOF mass spectrometry reveals both molecular weight and composition data. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 859–878, 1997     

Cobalt‐mediated catalytic chain‐transfer polymerization (CCTP) in water and water/alcohol solution

This article describes the use of cobalt‐mediated catalytic chain transfer in aqueous solution under fed conditions for the preparation of macromonomers of acidic, hydroxy, and zwitterionic functional monomers. Use of a batch reaction leads to hydrolysis of catalyst, a mixture of mechanisms and poor control of the reaction. A feed process is described that adds catalyst as a solution in monomer over the course of the reaction. The feed process is applied to a range of monomers of methacrylic acid ( 2 ), 2‐aminoethyl methacrylate hydrochloride ( 3 ), 2‐hydroxyethyl methacrylate ( 4 ), 2‐methacryloxyethyl phosphoryl choline ( 5 ), glycerol monomethyl methacrylate ( 6 ), and 3‐O‐methacryloyl‐1,2:5,6‐di‐O‐isopropylidene‐D ‐glucofuranose ( 7 ). Use of the feed process for water‐soluble monomers in conjunction with 1 as a catalytic chain‐transfer agent gives high‐conversion, > 90%, water‐soluble macromonomers. The number‐average molecular mass (M_n was determined by integration of the ¹H NMR spectrum comparing the vinylic end group with the remainder of the backbone. Pseudo‐Mayo plots were constructed by measuring the M_n at high conversion as a function of [monomer]/[catalyst] to give observed chain‐transfer constants of 1120, 958, and 1058 for 4, 6, and 2, respectively. All products were obtained as relatively high‐solid, homogeneous, low‐viscosity aqueous solutions. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2378–2384, 2001     

Polar,functionalized diene‐based materials. V. Free‐radical polymerization of 2‐[(N‐benzyl‐n‐methylamino)methyl]‐1,3‐butadiene and copolymerization with styrene

2‐[(N‐Benzyl‐N‐methylamino)methyl]‐1,3‐butadiene (BMAMBD), the first asymmetric tertiary amino‐containing diene‐based monomer, was synthesized by sulfone chemistry and a nickel‐catalyzed Grignard coupling reaction in high purity and good yield. The bulk and solution free‐radical polymerizations of this monomer were studied. Traditional bulk free‐radical polymerization kinetics were observed, giving polymers with 〈M_n〉 values of 21 × 10³ to 48 × 10³ g/mol (where M_n is the number‐average molecular weight) and polydispersity indices near 1.5. In solution polymerization, polymers with higher molecular weights were obtained in cyclohexane than in tetrahydrofuran (THF) because of the higher chain transfer to the solvent. The chain‐transfer constants calculated for cyclohexane and THF were 1.97 × 10^?3 and 5.77 × 10^?3, respectively. To further tailor polymer properties, we also completed copolymerization studies with styrene. Kinetic studies showed that BMAMBD incorporated into the polymer chain at a faster rate than styrene. With the Mayo–Lewis equation, the monomer reactivity ratios of BMAMBD and styrene at 75 °C were determined to be 2.6 ± 0.3 and 0.28 ± 0.02, respectively. Altering the composition of BMAMBD in the copolymer from 17 to 93% caused the glass‐transition temperature of the resulting copolymer to decrease from 64 to ?7 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3227–3238, 2001     

Catalytic‐chain‐transfer polymerization of styrene revisited: The importance of monomer purification and polymerization conditions

The cobaloxime‐mediated catalytic‐chain‐transfer polymerization of styrene at 60 °C was studied with an emphasis on the effects of monomer purification and polymerization conditions. Commonly used purification methods, such as column chromatography and simple vacuum distillation, were not adequate for obtaining kinetic data to be used in mechanistic modeling. A purification regime involving inhibitor removal with basic alumina, followed by polymerization of the styrene in the presence of the cobaloxime and subsequent vacuum distillation, was found to be essential to this end. It was then possible to quantitatively investigate effects such as the initiator concentration and conversion dependencies of the apparent chain‐transfer constant that resulted from the occurrence of cobalt–carbon bond formation. A value of about 9 × 10³ was found for the true chain‐transfer constant to cobaloxime boron fluoride, that is, its value in the absence of cobalt–carbon bond formation. Furthermore, previous predictions were confirmed: the measured chain‐transfer constant decreased with increasing initiator concentration and conversion. Finally, it was confirmed that the presence of light increased the amount of free Co(II) catalyst in agreement with other studies. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 752–765, 2003     

Cu(0)/2,6‐bis(imino)pyridines catalyzed single‐electron transfer‐living radical polymerization of methyl methacrylate initiated with poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)

A series of 2,6‐bis(imino)pyridines, as common ligands for late transition metal catalyst in ethylene coordination polymerization, were successfully employed in single‐electron transfer‐living radical polymerization (SET‐LRP) of methyl methacrylate (MMA) by using poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) (P(VDF‐co‐CTFE)) as macroinitiator with low concentration of copper catalyst under relative mild‐reaction conditions. Well‐controlled polymerization features were observed under varied reaction conditions including reaction temperature, catalyst concentration, as well as monomer amount in feed. The typical side reactions including the chain‐transfer reaction and dehydrochlorination reaction happened on P(VDF‐co‐CTFE) in atom‐transfer radical polymerization process were avoided in current system. The relationship between the catalytic activity and the chemical structure of 2,6‐bis(imino)pyridine ligands was investigated by comparing both the electrochemical properties of Cu(II)/2,6‐bis(imino)pyridine and the kinetic results of SET‐LRP of MMA catalyzed with different ligands. The substitute groups onto N‐binding sites with proper steric bulk and electron donating are desirable for both high‐propagation reaction rate and C? Cl bonds activation capability on P(VDF‐co‐CTFE). The catalytic activity of Cu(0)/2,6‐bis(imino)pyridines is comparable with Cu(0)/2,2′‐bipyridine under the consistent reaction conditions. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4378–4388     

Chain‐transfer reaction in the radical polymerization of di‐n‐butyl itaconate at high temperatures

Radical polymerizations of di‐n‐butyl itaconate were investigated. Unexpected resonances (C resonances) were observed in ¹³C NMR spectra of C?O of poly(di‐n‐butyl itaconate)s [poly(DBI)s] obtained at temperatures higher than 60 °C, although two kinds of carbonyl groups showed splittings due to triad tacticities in the spectra of polymers obtained at lower temperatures. The poly(DBI)s formed by the different kinds of initiators or formed in the presence of chain‐transfer agents showed hardly any changes in the intensities of the C resonances; this indicated that the C resonances were not due to the structures formed through initiating and terminating reactions. The poly(DBI)s obtained at different yields showed only a slight increase in the intensities of the C resonances with the yield, which suggested that the C resonances were not attributable to the intermolecular chain‐transfer reaction to the monomer and/or polymer. However, the intensities of the C resonances significantly increased with a decreasing feed monomer concentration; this suggested that intramolecular chain‐transfer reactions took place at high temperatures. Furthermore, a Cu complex‐catalyzed atom transfer radical polymerization mechanism was revealed to be effective for suppressing the intramolecular chain‐transfer reaction at 60 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2415–2426, 2002     

Reversible addition‐fragmentation chain transfer polymerization of methacrylates containing hole‐ or electron‐transporting groups

The controlled/living radical polymerization of 2‐(N‐carbazolyl)ethyl methacrylate (CzEMA) and 4‐(5‐(4‐tert‐butylphenyl‐1,3,4‐oxadiazol‐2‐yl)phenyl) methacrylate (t‐Bu‐OxaMA) via reversible addition‐fragmentation chain transfer polymerization has been studied. Functional polymers with hole‐ or electron‐transfer ability were synthesized with cumyl dithiobenzoate as a chain transfer agent (CTA) and AIBN as an initiator in a benzene solution. Good control of the polymerization was confirmed by the linear increase in the molecular weight (MW) with the conversion. The dependence of MW and polydispersity index (PDI) of the resulting polymers on the molar ratio of monomer to CTA, monomer concentration, and molar ratio of CTA to initiator has also been investigated. The MW and PDI of the resulting polymers were well controlled as being revealed by GPC measurements. The resulting polymers were further characterized by NMR, UV‐vis spectroscopy, and cyclic voltammetry. The polymers functionalized with carbazole group or 1,3,4‐oxadiazole group exhibited good thermal stability, with an onset decomposition temperature of about 305 and 323 °C, respectively, as determined by thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 242–252, 2007     

Kinetic investigation of the RAFT polymerization of p‐acetoxystyrene

The kinetics of the RAFT polymerization of p‐acetoxystyrene using a trithiocarbonate chain transfer agent, S‐1‐dodecyl‐S′‐(α,α′‐dimethyl‐α″‐acetic acid)trithiocarbonate, DDMAT, was investigated. Parameters including temperature, percentage initiator, concentration, monomer‐to‐chain transfer agent ratio, and solvent were varied and their impact on the rate of polymerization and quality of the final polymer examined. Linear kinetic plots, linear increase of M_n with monomer conversion, and low final molecular weight dispersities were used as criteria for the selection of optimized polymerization conditions, which included a temperature of 70 or 80 °C with 10 mol % AIBN initiator in bulk for low conversions or in 1,4‐dioxane at a monomer‐to‐solvent volume ratio of 1:1 for higher conversions This study opens the way for the use of DDMAT as a chain transfer agent for RAFT polymerization to incorporate p‐acetoxystyrene together with other functional monomers into well‐defined copolymers, block copolymers, and nanostructures. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2517–2524, 2010     

Synthesis of Structurally Well‐Defined Telechelic Polymers by Organostibine‐Mediated Living Radical Polymerization: In Situ Generation of Functionalized Chain‐Transfer Agents and Selective ω‐End‐Group Transformations

Several organostibine chain‐transfer agents possessing polar functional groups have been prepared by the reactions of azo initiators and tetramethyldistibine ( 1 ). Carbon‐centered radicals thermally generated from the azo initiators were trapped by 1 to yield the corresponding organostibine chain‐transfer agents. The high yields observed in the synthesis of the chain‐transfer agents strongly suggest that distibines have excellent radicophilic reactivity. As the reactions proceeded under neutral conditions, functional groups that are incompatible with ionic conditions were incorporated into the chain‐transfer agents. The chain‐transfer agents were used in living radical polymerization to synthesize the corresponding α‐functionalized polymers. As the functional groups in the chain‐transfer agents did not interfere with the polymerization reaction, well‐controlled polymers possessing number‐average molecular weights (M_ns) predetermined by the monomer/transfer agent ratios were synthesized with low polydispersity indices (PDIs). The organostibanyl ω‐polymer ends were transformed into a number of different functional groups by radical‐coupling, radical‐addition, and oxidation reactions. Therefore, it was possible to synthesize well‐controlled telechelic polymers with the same and also with different functional groups at their α‐ and ω‐polymer ends. Distibine 1 was also found to increase PDI control in the living radical polymerization of styrene and methyl methacrylate (MMA) using a purified organostibine chain‐transfer agent. Well‐controlled poly(methyl methacrylate)s with M_n values ranging from 10 000 to 120 000 with low PDIs (1.05–1.15) were synthesized by the addition of a catalytic amount of 1 . The results have been attributed to the high reactivity of distibine 1 towards polymer‐end radicals, which are spontaneously deactivated to yield organostibine dormant species.     

Influence of Amine‐Based Cationic Gemini Surfactants on Catalytic Activity of α‐Chymotrypsin

The α‐chymotrypsin activity was tested in aqueous media with the presence of novel cationic amine–based gemini surfactant, with different spacer chain lengths and head group size, and also compared with the cationic cetyltrimethylammonium bromide (CTAB) and cetyltriphenylphosphonium bromide (CTPB) surfactants and aqueous buffer only. The p‐nitrophenyl acetate (PNPA) hydrolysis rate was monitored in the presence of the surfactant concentration at 30°C. Most of these gemini surfactants gave higher catalytic activity as compared to cationic CTAB and CTPB. The highest superactivity was measured in the presence of gemini 16‐12‐16, [dodecanediyl‐1,12‐bis(cetyldimethylammonium bromide)] surfactant at pH 7.5. The catalytic reaction follows the Michaelis–Menten mechanism. The catalytic rate constants, k_cat, show the same profile that the catalytic affinity; K_M being enhanced with increasing space chain length. The results are favorable for considering that the amine‐based gemini surfactant influences more than both the aqueous and cationic micellar media.     

Radical polymerization of diallylamine compounds: From quantum chemical modeling to controllable synthesis of high‐molecular‐weight polymers

We investigated the possibility to obtain high‐molecular‐weight (HMW) polymers from the monomers of the diallylamine (DAA) series using quantum chemical and experimental methods. Such monomers are known to polymerize into oligomeric products due to the reaction of the degradative chain transfer to the monomer. We studied potential energy profiles of the chain propagation and competing chain transfer reactions, viz., the free radical double bond addition and α‐hydrogen radical abstraction, respectively, for a number of polymerization processes. Calculations were carried in the framework of the polarized continuum solvent model utilizing the procedure based on the semiempirical MNDO‐PM3 background. It was found that the necessary condition for decreasing competitiveness of the chain transfer to the monomer is the availability of monomer molecules in only protonated form in the polymerizing system. Using these results, we developed the strategy for obtaining HMW polymers based on said monomers. We synthesized a monomer system (the equimolar salt of N,N‐diallyl‐N‐methylamine and trifluoroacetic acid) that fully corresponds to such requirements. Novel HMW polymers were then synthesized by radical polymerization of this salt at soft conditions. We established that chain termination is controlled by the bimolecular mechanism. We showed that the degradative chain transfer transforms into the effective chain transfer. The mechanisms of the observed phenomena are discussed. © 2002 Wiley Periodicals, Inc. Int J Quantum Chem, 2002     

End‐functionalized copolymers prepared by the addition–fragmentation chain‐transfer method: Vinyl acetate/methacrylonitrile system

Copolymers of vinyl acetate and methacrylonitrile were prepared by free‐radical polymerization in the presence of the chain‐transfer agent (CTA) ethyl‐α‐ (t‐butanethiomethyl)acrylate. Molecular weight measurements showed that the chain‐transfer constants increased with the vinyl acetate content of the comonomer mixture, ranging from 0.42 for methacrylonitrile to 6.3 for the copolymerization of a vinyl acetate‐rich monomer mix (89/11). The bulk copolymer composition was not appreciably affected by the amount of CTA used in the copolymerization. The efficiency of the addition–fragmentation mechanism in producing specifically end‐functionalized copolymers was investigated with ¹H NMR spectroscopy. Spectral peaks consistent with all the expected end groups were observed for all comonomer feeds. Peaks consistent with other end groups were also observed, and these were particularly prominent for copolymers made with lower CTA concentrations. At the highest concentrations used, quantitative measurements of end‐group concentrations indicated that 70–80% of the end groups were those expected on the basis of the addition–fragmentation chain‐transfer mechanism. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2911–2919, 2001     

Homopolymerization of methyl methacrylate and styrene: Determination of the chain‐transfer constant from the Mayo equation and the number distribution for n‐dodecanethiol

Chain‐transfer constants were evaluated for n‐dodecanethiol in the homopolymerization of styrene (S) and methyl methacrylate (MMA). The polymerizations were carried out in benzene at 50 °C with different amounts of 2,2′‐azobisisobutyronitrile as the initiator. The new chain length distribution (CLD) analytical method was used and compared to the traditional Mayo method. The chain‐transfer‐constant values were independent of the initiator concentration and slightly higher (by a factor of 1.1 for MMA and 1.2 for S) when obtained according to the CLD method compared to the Mayo method. The chain‐transfer constant for S was 20 times higher than for MMA. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 170–178, 2000     

Catalytic synthesis of styryl‐capped isotactic polypropylenes

Bis‐styrenic molecules, 1,4‐divinylbenzene (DVB) and 1,2‐bis(4‐vinylphenyl)ethane (BVPE), were successfully combined with hydrogen (H₂) to form consecutive chain transfer complexes in propylene polymerization mediated by an isospecific metallocene catalyst (i.e., rac‐dimethylsilylbis(2‐methyl‐4‐phenylindenyl)zirconium dichloride, I ) activated with methylaluminoxane (MAO), rendering a catalytic access to styryl‐capped isotactic polypropylenes (i‐PP). The chain transfer reaction took place in a unique way where prior to the ultimate chain transfer DVB/H₂ or BVPE/H₂ caused a copolymerization‐like reaction leading to the formation of main chain benzene rings. A preemptive polymer chain reinsertion was deduced after the consecutive actions of DVB/H₂ or BVPE/H₂, which gave the styryl‐terminated polymer chain alongside a metal‐hydride active species. It was confirmed that the chain reinsertion occurred in a regio‐irregular 1,2‐fashion, which contrasted with a normal 2,1‐insertion of styrene monomer and ensured subsequent continuous propylene insertions, directing the polymerization to repeated DVB or BVPE incorporations inside polymer chain. Only as a competitive reaction, the insertion of propylene into metal‐hydride site broke the chain propagation resumption process while completed the chain transfer process by releasing the styryl‐terminated polymer chain. BVPE was found with much higher chain transfer efficiency than DVB, which was attributed to its non‐conjugated structure with much divided styrene moieties resulting in higher polymerization reactivity but lower chain reinsertion tendency. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3709–3713, 2010     

Radical polymerization of vinyl thiocyanatoacetate: Participation of group‐transfer mechanism

Vinyl thiocyanatoacetate (VTCA) was synthesized, and its radical polymerization behavior was studied in acetone with dimethyl 2,2′‐azobisisobutyrate (MAIB) as an initiator. The initial polymerization rate (R_p) at 60 °C was expressed by R_p = k[MAIB]^0.6±0.1 [VTCA]^1.0±0.1 where k is a rate constant. The overall activation energy of the polymerization was 112 kJ/mol. The number‐average molecular weights of the resulting poly (VTCA)s (1.4–1.6 × 10⁴) were almost independent of the concentrations of the initiator and monomer, indicating chain transfer to the monomer. The chain‐transfer constant to the monomer was estimated to be 9.6 × 10^?3 at 60 °C. According to the ¹H and ¹³C NMR spectra of poly (VTCA), the radical polymerization of VTCA proceeded through normal vinyl addition and intramolecular transfer of the cyano group. The cyano group transfer became progressively more important with decreasing monomer concentration. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 573–582, 2002; DOI 10.1002/pola.10137     

Reversible addition–fragmentation chain transfer polymerization of 2‐naphthyl acrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

The reversible addition–fragmentation chain transfer (RAFT) polymerizations of 2‐naphthyl acrylate (2NA) initiated by 2,2′‐azobisisobutyronitrile were investigated with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN) as a RAFT agent at various temperatures in a benzene solution. The results of the polymerizations showed that 2NA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion. The polydispersities of the polymer were relatively low up to high conversions in all cases. The chain‐extension reactions of poly(2‐naphthyl acrylate) (P2NA) with methyl methacrylate and styrene successfully yielded poly(2‐naphthyl acrylate)‐b‐poly(methyl methacrylate) and poly(2‐naphthyl acrylate)‐b‐polystyrene block polymers, respectively, with narrow polydispersities. The P2NA obtained by RAFT polymerization had a strong ultraviolet absorption at 270 nm, and the molecular weights had no apparent effect on the ultraviolet absorption intensities; however, the fluorescence intensity of P2NA increased as the molecular weight increased and was higher than that of 2NA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2632–2642, 2005     

Block copolymers based on 2‐vinyl‐4,4‐dimethyl‐5‐oxazolone by RAFT polymerization: Experimental and computational studies

The ability of 2‐vinyl‐4,4‐dimethyl‐5‐oxazolone (VDM), a highly reactive functional monomer, to produce block copolymers by reversible addition fragmentation chain transfer (RAFT) sequential polymerization with methyl acrylate (MA), styrene (S), and methyl methacrylate (MMA) was investigated using cumyl dithiobenzoate (CDB) and 2‐cyanoisopropyl dithiobenzoate (CPDB) as chain transfer agents. The results show that PS‐b‐PVDM and PMA‐b‐PVDM well‐defined block copolymers can be prepared either by polymerization of VDM from PS‐ and PMA‐macroCTAs, respectively, or polymerization of S and MA from a PVDM‐macroCTA. In contrast, PMMA‐b‐PVDM block copolymers with controlled molecular weight and low polydispersity can only be obtained by using PMMA as the macroCTA. Ab initio calculations confirm the experimental studies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Viscosity effects in cobaloxime‐mediated catalytic chain‐transfer polymerization of methacrylates

The effect of bulk viscosity on the cobaloxime‐mediated catalytic chain‐transfer polymerization of methacrylates at 60 °C was investigated by both the addition of high molecular weight poly(methyl methacrylate) to methyl methacrylate polymerization and the dilution of benzyl methacrylate polymerization by toluene. The results indicate that the bulk viscosity is not directly linked to the chain‐transfer activity. The previously measured relationship between chain‐transfer‐rate coefficient and monomer viscosity therefore probably reflects changes at the molecular level. However, the results in this article do not necessarily disprove a diffusion‐controlled reaction rate because cobaloxime diffusion is expected to scale with the monomer friction coefficient rather than bulk viscosity. Considering the published data, to date we are not able to distinguish between a diffusion‐controlled reaction rate or a mechanism directly affected by the methacrylate substituent. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 782–792, 2002; DOI 10.1002/pola.10152     

Optimization of an α‐(Amino acid)‐N‐carboxyanhydride polymerization using the high vacuum technique: Examining the effects of monomer concentration,polymerization kinetics,polymer molecular weight,and monomer purity

l ‐Ornithine‐based poly(peptides) have been widely utilized in the field of drug delivery, however few studies have been conducted examining the details of polymerization. In this article, the effects of monomer concentration, polymerization kinetics, polymer molecular weight and monomer purity were investigated using l ‐carboxybenzyl (Cbz)‐ornithine as a model monomer. The mechanism of polymerization herein follows the normal amine mechanism to produce poly(peptides) having controlled molecular weights, known chain ends and a narrow polydispersity index (PDI). A preferred monomer concentration range was determined, which required minimal polymerization times and allowed for predictable and reproducible molecular weights with narrow PDIs. The impact of monomer purity on the polymerization was established and monomer purification conditions are reported, which produce high‐purity monomer after a single recrystallization. Additionally, the optimized polymerization conditions and monomer purification protocol were combined with a sequential monomer addition technique to produce high molecular weight poly(ornithine) with a narrow PDI and known chain ends. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1385–1391