Preparation and characterization of star ABC triblock copolymer of ethylene oxide,styrene and methyl methacrylate

A universally significant method,which combines the anionic polymerization with photoinduced charge transfer polymerization,for preparation of soluble star ABC triblock copolymer of ethylene oxide,styrene and methyl methacrylate,was described.The poly(ethylene oxide) (PEO) block was formed by initiation of phenoxy an-ions using p-aminophenol protected by Schiff's base as the parent compound Then the charge transfer system composed of PEO chains with deprotected-amino end groups and benzophenone initiated the polymerization of styrene and methyl metnacrylate sequentially under UV irradiation.The formed star triblock copolymer of styrene,ethylene oxide and methyl methacrylate could be purified by thin-layer chromatography (TLC) and characterized by IR,1H NMR,GPC (gel permeation chromatogrphy) and PGC (pyrolysis gas chromatography).     

Synthesis and characterization of linear ABC triblock copolymer of ethylene oxide,methyl methacrylate,and styrene

A well‐defined linear ABC triblock copolymer of ethylene oxide (EO), methyl methacrylate (MMA), and styrene (St) was prepared by sequential living anionic and photo‐induced charge transfer polymerization (CTP) using p‐aminophenol as parent compound. In the first step, the diblock copolymer of PEO‐b‐PMMA with a protected aniline end group at PEO end was prepared by initiating of phenoxo‐anion the polymerization of EO and MMA successively, then the diblock copolymer of PEO‐b‐PMMA via deprotection of aniline at PEO end constituted a binary initiation system with benzophenone (BP) by charge transfer complex mechanism to initiate the polymerization of St under UV‐irradiation. The GPC and NMR measurements support that in copolymerization, either in the first or second step, neither homopolymer nor side reactions, such as chain transfer or chain termination, was found. The effect of the concentration of PEO_a‐b‐PMMA and St, and the polarity of solvent on the polymerization rate (R_p) of CTP is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 825–833, 1999     

The micellization of the diblock copolymer of ethylene oxide and styrene in benzene and the effect on the preparation of the star ABC triblock copolymer of ethylene oxide, styrene and methyl methacrylate

In the preparation of the ABC star triblock copolymer of ethylene oxide, styrene and methyl methacrylate (MMA), the photo-induced charge-transfer complex (CTC) was used to initiate the polymerization of the third monomer MMA. The CTC was composed of the diblock copolymer of poly(ethylene oxide) (PEO) and polystyrene (PS), PEO-b _i -PS, with an aromatic imino group at the conjunction point and benzophenone (BP). It was confirmed that the kinetic behavior of this macromolecular initiation system is nearly the same with a general small radical initiator: the polymerization rate R _p ∝ [PEO-b _i -PS]^0.48[BP]^0.45[MMA]^0.97. Moreover, if the molecular weight of the PEO block is fixed, R _p is independent of the molecular weight of the PS block.  By means of measurements of viscosity and fluorescence, it was found that the micelles of the diblock copolymer PEO-b _i -PS were formed in benzene. The aromatic imino groups were located on the boundary surfaces of the micelles and were fully exposed, and so the BP and MMA molecules easily approached them and affected the charge-transfer polymerization of MMA. Received: 18 August 1998 Accepted in revised form: 25 November 1998     

Surface-induced morphologies of ABC star triblock copolymer in spherical cavities

The morphologies and phase diagrams exhibited by symmetric ABC star triblock copolymer nanoparticles are investigated on the basis of real-space self-consistent field theory. The ABC star triblock copolymers were chosen to be tiling-forming with fixed polymer parameter and the spherical boundaries were modeled using the masking technique. We first study a number of examples where the ABC triblock copolymers confined in spherical cavities with neutral surface. Then, two types of spherical cavity distinct preferential surfaces are considered, including both A-block attractive and repulsive preferential surfaces. We aim at the effects due to various spherical cavity diameters and the degree of interactions between the polymer and the spherical surface. A variety of morphologies, such as ring-like structures, concentric sphere, and irregular cylinder, were identified in phase diagrams. The results show that both the degree of interactions and spherical diameters can influence the formation of morphologies so that ring-like structures and other novel structures could be obtained.     

Synthesis and characterization of poly(ethylene oxide)/polylactide/poly(ethylene oxide) triblock copolymer

Poly(ethylene oxide/polylactide/poly(ethylene oxide) (PEO/PL/PEO) triblock copolymers, in which each block is connected by an ester bond, were synthesized by a coupling reaction between PL and PEO. Hydroxyl‐terminated PLs with various molecular weights were synthesized and used as hard segments. Hydroxyl‐terminated PEOs were converted to the corresponding acid halides via their acid group and used as a soft segment. Triblock copolymers were identified by Fourier transform infrared spectroscopy, ¹H NMR, and gel permeation chromatography. Differential scanning calorimetry (DSC) and X‐ray diffractometry of PEO/PL/PEO triblock copolymers suggested that PL and PEO blocks were phase‐separated and that the crystallization behavior of the PL block was markedly affected by the presence of the PEO block. PEO/PL/PEO triblock copolymers with PEO 0.75k had two exothermic peaks (by DSC), and both peaks were related to the crystallization of PL. According to thermogravimetric analysis, PEO/PL/PEO triblock copolymer showed a higher thermal stability than PL or PEO. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2545–2555, 2002     

Self-assembly of star ABC triblock copolymer thin films: self-consistent field theory

Microphase separation and morphology of star ABC triblock copolymers confined between two identical parallel walls (symmetric wetting or dewetting) are investigated with self-consistent field theory (SCFT) combined with the "masking" technique to describe the geometric confinement of the films. In particular, we examine the morphology of confined near-symmetric star triblock copolymers under symmetric and asymmetric interactions as a function of the film thickness and the surface field. Under the interplay between the degree of spatial confinement, characterized by the ratio of the film thickness to bulk period, and surface field, the confined star ABC triblock copolymers are found to exhibit a rich phase behavior. In the parameter space we have explored, the thin film morphologies are described by four primary classes including cylinders, perforated lamellae, lamellae, and other complex hybrid structures. Some of them involve novel structures, such as spheres in a continuous matrix and cylinders with alternating helices structure, which are observed to be stable with suitable film thickness and surface field. In particular, complex hybrid network structures in thin films of bulk cylinder-forming star triblock copolymers are found when the natural domain period is not commensurate with the film thickness. Furthermore, a strong surface field is found to be more significant than the spatial confinement on changing the morphology of star triblock copolymers in bulk. These findings provide a guide to designing novel microstructures involving star triblock copolymers via geometric confinement and surface fields.     

Preparation of styrene/methacrylic acid copolymer microspheres and their composites with metal particles

 Poly(styrene-co-methacrylic acid) [P(St-co-MAA)] microspheres were prepared by emulsifier-free emulsion copolymerization of St with MAA. Fourier transform IR spectroscopy and elemental analysis were used to study the change in the content of MAA in the microspheres. The results of X-ray photoelectron spectroscopy measurements indicated the presence of carboxylic functionality on the surface of the microspheres. The P(St-co-MAA) metal composite particles were prepared by chemical metal deposition. Transmission electron microscopy observation and X-ray diffraction measurement were used to study the distribution and structure of the metal particles deposited. Received: 15 September 1999 Accepted: 24 December 1999     

Synthesis and characterization of biocompatible, thermoresponsive ABC and ABA triblock copolymer gelators

The synthesis of doubly thermoresponsive PPO-PMPC-PNIPAM triblock copolymer gelators by atom transfer radical polymerization using a PPO-based macroinitiator is described. Provided that the PPO block is sufficiently long, dynamic light scattering and differential scanning calorimetry studies confirm the presence of two separate thermal transitions corresponding to micellization and gelation, as expected. However, these ABC-type triblock copolymers proved to be rather inefficient gelators: free-standing gels at 37 degrees C required a triblock copolymer concentration of around 20 wt%. This gelator performance should be compared with copolymer concentrations of 6-7 wt% required for the PNIPAM-PMPC-PNIPAM triblock copolymers reported previously. Clearly, the separation of micellar self-assembly from gel network formation does not lead to enhanced gelator efficiencies, at least for this particular system. Nevertheless, there are some features of interest in the present study. In particular, close inspection of the viscosity vs temperature plot obtained for a PPO43-PMPC160-PNIPAM81 triblock copolymer revealed a local minimum in viscosity. This is consistent with intramicelle collapse of the outer PNIPAM blocks prior to the development of the intermicelle hydrophobic interactions that are a prerequisite for macroscopic gelation.     

Preparation of intermediary layer crosslinked micelles from a photocrosslinkable amphiphilic ABC triblock copolymer

To prepare intermediary layer crosslinked micelles, a photocrosslinkable amphiphilic ABC triblock copolymer, poly(ethylene glycol)-b-poly(2-cinnamoyloxyethyl methacrylate)-b-poly(methyl methacrylate) (PEG-PCEMA-PMMA), was synthesized and its micellar characteristics were investigated. The triblock copolymer of PEG-b-poly(2-hydroxyethyl methacrylate)-b-PMMA (PEG-PHEMA-PMMA) (M_n = 9800 g/mol, M_w/M_n = 1.33) was first polymerized by activators generated by electron transfer (AGET) atom transfer radical polymerization (ATRP) using a PEG macroinitiator in a mixed solvent of anisole/2-isopropanol (3/1 v/v). The middle block of the copolymer was then functionalized with cinnamoyl chloride. The degrees of polymerization of the PEG, PHEMA, and PMMA blocks were 113, 18 and 21, respectively. The critical micelle concentration (CMC) of the PEG-PCEMA-PMMA was 0.011 mg/mL. The PEG-PCEMA-PMMA micelles were spherically shaped with an average diameter of 43 nm. The intermediary layer of the PEG-PCEMA-PMMA micelles was crosslinked by UV irradiation. Not all of the cinnamate groups underwent photocrosslinking probably due to a lack of other cinnamate groups in their immediate vicinity. However, the degree of photocrosslinking of the intermediary layer of the PEG-PCEMA-PMMA micelles was sufficient to give excellent colloidal stability, even in different external environments.     

Synthesis of a novel diblock copolymer of isoprene and methacrylic acid

A new diblock copolymer of isoprene (I) and methacrylic acid (MAA) was prepared by combination of an anionic mechanism with a charge transfer complex mechanism. In the first step, the polyisoprene (PI) macroanion formed by initiation with butyllithium was capped by p-dimethylaminobenzaldehyde (capped polyisoprene = PI_d); a dimeric coupling product was not detected. Then the binary system constituting of PI_d and benzophenone was used to initiate the polymerization of MAA under UV irradiation. The resulting diblock copolymer (PI-b-PMAA) was characterized by IR, NMR and gel permeation chromatography (GPC) in detail.     

环氧乙烷与苯乙烯两亲性聚合物的合成

Graft eopolymer eontaining poly(ethylene oxide)side chains on a polystyrene backbone were acrylamided. The amide groups in the copolymers were ionized by using potassium naphthalene, and grafting was achieved by utilizing the amide anions as initiator sites for the polymerization of ethylene oxide at 70℃. The graft copolymers was characterized with respect to molecule weight and composition using NMR, IR, GPC, and DSC. GPC result from the graft copolymer sample suggested a narrow size distribution.     

Self-assembly of ABC star triblock copolymer thin films confined with a preferential surface: a self-consistent mean field theory

The microphase separation and morphology of a nearly symmetric A(0.3)B(0.3)C(0.4) star triblock copolymer thin film confined between two parallel, homogeneous hard walls have been investigated by self-consistent mean field theory (SCMFT) with a pseudospectral method. Our simulation experiments reveal that under surface confinement, in addition to the typically parallel, perpendicular, and tilted cylinders, other phases such as lamellae, perforated lamellae, and complex hybrid phases have been found to be stable, which is attributed to block-substrate interactions, especially for those hybrid phases in which A and B blocks disperse as spheres and alternately arrange as cubic CsCl structures, with a network preferred structure of C block. The results show that these hybrid phases are also stable within a broad hybrid region (H region) under a suitable film thickness and a broad field strength of substrates because their free energies are too similar to being distinguished. Phase diagrams have been evaluated by purposefully and systematically varying the film thickness and field strength for three different cases of Flory-Huggins interaction parameters between species in the star polymer. We also compare the phase diagrams for weak and strong preferential substrates, each with a couple of opposite quality, and discuss the influence of confinement, substrate preference, and the nature of the star polymer on the stability of relatively thinner and thick film phases in this work.     

Multicompartment micelles from star and linear triblock copolymer blends

Dissipative particle dynamics simulations were performed on multicompartment micelles formed by blending star and linear triblock copolymers, in which the influences of blending options and blending ratio as well as copolymer chain compositions were studied systematically. The results show that blending of copolymers with different architectures is a promising strategy to control the morphology and structure of multicompartment micelles. This work revealed several new morphologies of multicompartment micelles by blending star and linear triblock copolymers, and the dynamic processes were elucidated at the molecular level by tracing the motions of copolymer chains. The results of this work provide deep insight into micro/mesoscopic details of the underlying mechanisms, contributing to a more complete understanding of multicompartment micelle formation and structural control.     

Synthesis and self-assembly properties of a novel [poly(ethylene glycol)]-fluorocarbon-phospholipid triblock copolymer

The synthesis of a novel poly(ethylene glycol)-fluorocarbon-phospholipid conjugate that self-assembles into hyper-stable micelles characterized by an internal fluorous phase is described. Physical characterization of the micelles formed by this polymer in aqueous solution is included. Dynamic light scattering (DLS) measurements indicate a mean diameter of 15 nm (±3 nm), while pyrene fluorescence studies show a critical micelle concentration (CMC) of only 0.65 μM.     

Morphology of ABC triblock copolymer/homopolymer blend systems

Morphological variations of ABC triblock copolymers through the blending of B or A/C homopolymers, all with short chain lengths, were studied experimentally. The samples were symmetric ISP triblock copolymers, where I, S, and P denote polyisoprene, polystyrene, and poly(2‐vinylpyridine), and component homopolymers. Microphase‐separated structures of the solvent‐cast films were observed with transmission electron microscopy and small‐angle X‐ray scattering. For an ISP/S system, the lattice constant of the tricontinuous gyroid structure (G‐structure) increased with an increase in the volume fraction of S (?_s) if the amount of added homopolymer was small, but it reached a certain limit, reflecting the fact that the midblock chain had a limit for chain stretching. For I/ISP/P blends, on the contrary, the lattice constant of the G‐structure continued increasing with decreasing ?_s. This result shows that the I and P domains did not have a limit for chain stretching because the two end blocks had free ends. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1135–1141, 2002     

Thermal and self-nucleation behavior of molecular complexes formed by p-nitrophenol and the poly(ethylene oxide) end block within an ABC triblock copolymer

We have been able to prepare a molecular complex between the poly(ethylene oxide) block of a poly(ethylene)-b-poly(ethylene-alt-propylene)-b-poly(ethylene oxide) triblock copolymer and p-nitrophenol (PNP). The composition of the copolymer employed was: 24% PE, 57% PEP and 19% PEO in weight percent. The pure copolymer exhibited a non-conventional thermal behavior since the PEO block displayed a fractionated crystallization process during cooling. The PEO block/PNP complex did not show any apparent crystallization during cooling, instead cold crystallization during heating was observed and an approximately 30°C increase in melting point as compared to the neat PEO block within the copolymer. This caused an overlap in the melting regions of the PE block and the PEO block/PNP complex. The self-nucleation of the PE-b-PEP-b-PEO/PNP complex is very different from that of the neat triblock copolymer. An increased capacity for self-nucleation of the PEO block was produced by the complexation with PNP and therefore the three self-nucleation domains were clearly encountered for both the PE block and for the PEO block/PNP complex. Self-nucleation was able to show that the two crystallizable blocks can be self-nucleated and annealed in an independent way, thereby ascertaining the presence of separate crystalline regions in the triblock copolymer. Through the use of PNP, both the crystallinity and the melting point of the PE-b-PEP-b-PEO block copolymer employed here can be substantially increased. Similar results were obtained by complexation of the same ABC triblock copolymer with resorcinol.     

两亲性杂臂星型嵌段共聚物胶束的制备、表征及载药性能研究

以溴代异丁酰溴与3,5-二羟基苯甲酸制备3,5-二(2-溴-2丙酰氧基)苯甲酸,再与聚乙二醇单甲醚酯化,合成含溴大分子引发剂PEG-Br2。以苯乙烯为单体,利用原子转移自由基聚合方法(ATRP)合成了两种不同亲疏水段比例的两亲性星型杂臂嵌段共聚物PEG-b-(PS)2。本实验利用FTIR、1H-NMR、GPC等技术对聚合物的分子结构及分子量进行表征,利用透析法制备聚合物胶束;采用AFM对聚合物胶束的纳米结构进行观察;采用荧光探针法测得其临界胶束浓度(CMC)分别为0.99 mg·L-1和0.59 mg·L-1;利用DLS测得聚合物胶束粒径为150 nm左右;以疏水型抗肿瘤药物氨甲喋呤(MTX)为模型药物,对载药胶束的体外释药行为进行了研究,测得聚合物胶束的载药量分别为为13.32%和10.00%,包封率分别为61.75%和46.82%。结果表明,随着疏水段的增大,星型杂臂嵌段共聚物胶束药物包载量及CMC随之降低,且在人体pH条件下药物释放较低;同时发现两种载药胶束在肿瘤细胞酸性条件下释药速率增加。综上,此类结构的聚合物胶束作为抗肿瘤药物MTX的载体分子具有很好的应用前景。