Strain‐induced crystallization and strength of elastomers. I. cis‐1,4‐polybutadiene

Crosslinked samples of cis‐1,4‐polybutadiene (BR) were crystallized at low temperatures and then slowly melted. From volume changes and differential scanning calorimetry measurements, the degree of crystallization in the unstrained state was estimated to be about 20%, much lower than for natural rubber (NR). Crystallization and melting were followed in stretched samples by corresponding changes in tensile stress. Crystallization was faster at higher strains, and the melting temperature was raised significantly on stretching but less than for NR, and the decrease in stress on crystallizing was smaller. Measurements of tensile strength were made over a wide temperature range and showed a marked drop with heating to temperatures of 40–60 °C, falling to values of only 1–2 MPa. A similar drop in strength occurred in NR vulcanizates at high temperatures and was attributed to failure to crystallize on stretching (A. G. Thomas & J. M. Whittle, Rubber Chem Technol 1970, 43, 222; A. N. Gent, S. Kawahara & J. Zhao, Rubber Chem Technol 1998, 71, 668). At ambient temperatures, where strain‐induced crystallization occurred, the strength of BR samples was only about one‐half of that of similar NR materials. This was attributed to less strain‐induced crystallinity in BR (verified by X‐ray studies), paralleling the lower amount developed at low temperatures. We speculate that the higher density of molecular entanglements in BR than in NR prevents BR from crystallizing to the same degree as NR. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 811–817, 2001     

Synthesis of cyclic polybutadiene via ring-opening metathesis polymerization: the importance of removing trace linear contaminants

The synthesis of cyclic polybutadienes using ring-opening metathesis polymerization (ROMP) was accomplished. A cyclic Ru alkylidene catalyst, where a terminal ligand was covalently linked to the Ru alkylidene, was used to polymerize either 1,5-cyclooctadiene (COD) or 1,5,9-trans-cis-trans-cyclododecatriene (CDT). Trace amounts of an acyclic impurity, 4-vinylcyclohexene, found in the COD led to samples which were contaminated with linear polymer. In contrast, CDT, which was free of the impurity, afforded pure cyclic polymer. These results provide a convenient method for discerning samples of pure cyclic polymer from those which contain trace to large amounts of linear polymer. Furthermore, they emphasize the need to use monomers that are free of acyclic impurities when preparing cyclic polymers using ROMP.     

Computational Study of Metathesis Degradation of Rubber, 3. Distribution of Cyclic and Linear Oligomers via Intermolecular Degradation of cis‐Poly(butadiene)

The molecular modeling of the product distributions for the intermolecular metathesis degradation of cis‐poly(butadiene) (cis‐PB) in the presence of ethylene as chain‐transfer agent (CTA) at 298.15 K using the B3LYP/6‐31G (d, p) level of theory reveals that chain–ring and chain‐chain equilibria are shifted toward the formation of 1,5‐hexadiene. The amount of cyclic oligomers at equilibrium with linear molecules is negligible. The α,ω‐vinyl‐terminated butadiene oligomers–1,5‐hexadiene equilibrium constant depends on the cis/trans isomer ratio in linear butadiene molecules. While the concentration of 1,5‐hexadiene at equilibrium with cis‐butadiene oligomers is 86 mol‐%, this value for trans‐butadiene oligomers corresponds to 50 mol‐% of 1,5‐hexadiene. The results of calculations are in reasonable agreement with recent experimental data on the intermolecular metathesis of 1,4‐cis‐PB with ethylene using a well‐defined ruthenium alkylidene catalyst. The calculations predict that cis‐butene as a CTA is more efficient in the metathesis depolymerization of cis‐PB compared with ethylene.     

Effect of chain structure on the glass transition temperature and viscoelastic property of cis‐1,4‐polybutadiene via molecular simulation

In this work, by adopting the united atom model of cis‐1,4‐poly(butadiene) (PB), we systemically investigate the effect of the chain structure on the glass transition temperature (T_g) and the viscoelastic property of PB system. First, we analyze the atom translational mobility, bond reorientation dynamics, torsional dynamics, conformational transition rate, and dynamic heterogeneity of the PB chains with different chain structures in detail by determining the corresponding T_g. In addition, our results clearly indicate that with the decrease of the amount of the free end atoms of PB via the end‐linking method, the mobility of the PB chains quickly decreases. As a result, the T_g of the PB chains gradually increases. Depending on the chain structure and the calculation method, the T_g of the PB chains varies from 154 to 240 K. In addition, the temperature dependence of the dynamic properties has different Arrhenius behaviors above and below T_g. The calculated activation energy varies from 7.37 to 16.37 KJ/mol for different chain structures above T_g, which can be compared with those for other polymers. In addition, through the end‐linking approach the strong interaction between the PB chains improves the storage modulus G′ and the loss modulus . Meanwhile, the immobility of the free end atoms effectively reduces the friction loss of the chains under the shear field, which is reflected by the low loss factor . In summary, this work can further help to understand the effect of the chain structure on the dynamic properties of the PB chains. Meanwhile, it provides an effective approach to reduce the energy loss during the dynamic periodic deformation, which can cut the fuel consumption via the end‐linking method. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1005–1016     

Infrared microspectroscopic study of the thermo-oxidative degradation of hydroxy-terminated polybutadiene/isophorone diisocyanate polyurethane rubber

Hydroxy-terminated polybutadiene/isophorone diisocyanate (HTPB/IPDI) polyurethane rubber which was aged in air at elevated temperatures has been studied by infrared microspectroscopy. Spectra were collected in transmission mode on microtomed samples. Analysis of sets of spectra taken across the sectioned material showed that most of the degradation occurred in the polybutadiene part of the polymer and that the urethane linkage was essentially unchanged. The trans isomer of the polybutadiene appears to be preferentially degraded compared with the vinyl isomer. The IR technique does not provide significant information about the cis isomer. The IR spectra indicated that likely degradation products included acids, esters, alcohols, and small amounts of other products containing a carbonyl functional group. Band area ratios, supported by a principal components analysis, were used to derive degradation profiles for the material. These profiles were steep-sided indicating an oxygen diffusion limited process.     

Many‐body interactions of carbon monoxide cyclic oligomers: A computational study

Structural properties and energetics for the optimized carbon monoxide cyclic oligomers are analyzed at the correlated ab initio second‐order Møller–Plesset (MP2) and density functional methods (B3LYP and mPW1PW), using Dunning's cc‐pVXZ (X = D, T, Q) basis set, augmented with diffuse functions. Many‐body interactions of the stable carbon monoxide cyclic oligomers, (CO)₄ and (CO)₅ are computed at the MP2/aug‐cc‐pVTZ level. Contributions of two‐ to five‐body terms to each of these oligomers for their interaction energies, including corrections for basis set superposition error (BSSE) are investigated by using function counterpoise and its generalized version. It has been found that three‐body terms are attractive in nature and essential in order to describe the cooperative effects in the stable cyclic CO oligomers. © 2005 Wiley Periodicals, Inc. Int J Quantum Chem, 2005     

Formation of higher cyclic oligomers in polyamide‐4,6

An example of morphology‐steered chemistry of cyclic oligomers with the example of polyamide‐4,6 (PA46) is discussed in this article. The cyclic oligoamide profiles of solid‐state post condensed PA46 show an unusual maximum for intermediate cycles consisting of 10 and 12 amide groups, which are formed in the initial stage of solid state post condensation. This is explained from the short chain length at the start of the post condensation, the preorganization of linear oligomers in the lamellar crystal structure, and the occurrence of amide units in the PA46 lamellar folds. Further the development of the cyclic oligomers up to the cyclic hexadecamide is followed on heating the base polymer in the melt at 310 °C, where it showed to react back to the theoretical Jacobsen and Stockmayer distribution. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of novel cyclic olefin polymers with excellent transparency and high glass‐transition temperature via gradient copolymerization of bulky cyclic olefin and cis‐cyclooctene

Novel cyclic olefin polymers (COPs) with excellent transparency and high glass‐transition temperature (T_g) synthesized from bulky norbornene derivative, exo‐1,4,4a,9,9a,10‐hexahydro‐9,10(1',2')‐benzeno‐l,4‐methanoanthracene (HBMN), and cis‐cyclooctene (COE) by ring‐opening metathesis copolymerization utilizing the “first‐generation Grubbs” catalyst, RuCl₂(PCy₃)₂(CHPh), and subsequent hydrogenation was reported herein. To get amorphous copolymers, it was of great importance to control the feed ratios and the polymerization time for gradient copolymerization. All these copolymers showed very high T_gs (141.1–201.2 °C), which varied with the content of HBMN. The films of the gradient copolymers with only one T_g were highly transparent. On the contrary, all the block copolymers synthesized through sequential addition showed two thermal transition temperatures, T_g and melt temperature (T_m), and the films of these block copolymers were opaque. The mechanical performances of the COPs were also investigated. It is the first report that transparent COP could be prepared from bulky norbornene derivative and monocyclic olefin. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3240–3249     

Determination of carboxyl content in carboxylated nitrile butadiene rubber (XNBR) after degradation via olefin cross metathesis

Carboxyl content in nitrile butadiene rubber (XNBR) has an impact on its application performance. However, its poor solubility makes it difficult to determine the carboxyl content in XNBR due to its high molecular weight. In the present work, olefin cross metathesis was used to degrade XNBR with acrylonitrile (AN) as chain transfer agent for the first time, to solve the solubility problem. After degradation under the optimized condition, with 2% AN and 0.2% catalyst at 60 °C for 30 min, the weight-average molecular weight (M_w) of the product decreased to 0.98 × 10⁴ with distribution (M_w/M_n) of 3.83. Such product was easy to be dissolved, so the carboxyl content in XNBR could be determined with the routine titrimetric analysis methods.     

Preparation and properties of nanocomposites based on acrylonitrile–butadiene rubber,styrene–butadiene rubber,and polybutadiene rubber

Nanocomposites were prepared with different grades of nitrile rubber with acrylonitrile contents of 19, 34, and 50%, with styrene–butadiene rubber (23% styrene content), and with polybutadiene rubber with Na‐montmorillonite clay. The clay was modified with stearyl amine and was characterized by X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM). The XRD studies showed an increase in the gallery gap upon the modification of the filler by stearyl amine. The intercalation of the amine chains into the clay gallery gap was confirmed by the presence of some extra peaks (2928, 2846, and 1553 cm^?1) in the FTIR spectra. The clay–rubber nanocomposites were characterized by TEM and XRD. The mechanical properties were studied for all the compositions. An improvement in the mechanical properties with the degree of filler loading up to a certain level was observed. The changes in the mechanical properties, with changes in the nature and polarity of the rubbers, were explained with the help of XRD and TEM results. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1573–1585, 2004     

Organocatalyzed ring‐opening polymerization of cyclic butylene terephthalate oligomers

In this study, various organic compounds, with different activation modes, have been tested as catalysts for the ring‐opening polymerization (ROP) of cyclic butylene terephthalate oligomers (CBT) in bulk at 210 °C, using tert‐butylbenzyl alcohol (tBnOH) as initiator. Among them, 1,3,5‐triazabicyclo[4.4.0]dec‐5‐ene (TBD) appeared to be the most efficient, achieving high monomer conversions in short reaction times (within minutes). Analysis by size‐exclusion chromatography (SEC) of the poly(butylene terephthalate) (PBT) synthesized using this catalyst also showed that the polymerization follows the expected theoretical M _n trend for molecular weights up to 50 kg·mol^?1. Chain‐end fidelity relatively to the alcohol initiator has been confirmed by MALDI‐TOF mass spectroscopy, which showed that all polymer chains possess the tert‐butylbenzyl moiety as chain‐end. Finally, to demonstrate the potential of this system for the synthesis of PBT‐based block copolymers, a monomethyl ether poly(ethylene glycol) (PEG) of 5000 g·mol^?1 has been employed as initiator for the ROP of CBT. A PEO‐b‐PBT block copolymer of 15,000 g·mol^?1 could thus been obtained, as confirmed by the shift of the SEC traces towards higher molecular weights and the same diffusion coefficient determined for ¹H NMR signals of the PEO block and the PBT block. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1611–1619     

Replacement of benzene with regulators for the catalyzed polymerization of 1,3‐butadiene to high cis‐1,4‐polybutadiene

The polymerization regulators mesitylene and 1,3,5‐trimethoxybenzene were investigated as suitable substitutes for benzene in the cobalt(II) octanoate/diethylaluminum chloride/water‐catalyzed polymerization of 1,3‐butadiene to high cis‐1,4‐polybutadiene. The propagation rates were reduced by 50% with the inclusion of 18 mM mesitylene or 0.17 mM trimethoxybenzene. Mesitylene was found to be an inefficient polymerization regulator because it reduced the propagation rate by a combination of regulation and destruction of the active catalyst complex. Not only did trimethoxybenzene reduce the propagation rate by effective regulation at low concentration, it also increased the percentage activity of cobalt to 200%, indicating that two polymer chains were propagating simultaneously from each active center. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2244–2255, 2001     

Synthesis of thiophene/phenylene co‐oligomers. II [1]. Block and alternating co‐oligomers

We report the synthesis of block and alternating thiophene/phenylene co‐oligomers that is based either on the Suzuki coupling reaction or on the Grignard reaction. These reaction schemes enable us to obtain the target compounds at reasonably high yields. The resulting materials have been fully characterized through the solid‐state ¹³C nmr and Fourier‐transform ir as well as the ¹H nmr. Of these, the solid‐state ¹³C nmr and ir are particularly useful in characterizing the materials of higher molecular weight, since those materials are difficult to dissolve in organic solvents.     

Synthesis of polybutadiene‐based particles via dispersion ring‐opening metathesis polymerization

Latex particles based on 1,4‐polybutadiene were synthesized via dispersion ring‐opening metathesis copolymerization of 1,5‐cyclooctadiene with a α‐norbornenyl poly(ethylene oxide) macromonomer. Stable but polydisperse colloidal dispersions in the 50 nm to 10 μm size range were obtained. In this work, particular attention was paid to the effects of the kinetics of copolymerization on the structure of the graft copolymers formed and on the onset of turbidity. Strategies to prepare monodisperse polybutadiene particles were also designed through the growth of a polybutadiene shell from a well‐defined polynorbornene seed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1154–1163, 2004     

Synthesis of POSS‐terminated polycyclooctadiene telechelics via ring‐opening metathesis polymerization

In this contribution, we reported the synthesis of a series of POSS‐terminated polycyclooctadiene (PCOD) telechelics via ring‐opening metathesis polymerization (ROMP) approach. Toward this end, 1,4‐diPOSS‐but‐2‐ene was synthesized via copper‐catalyzed Huisgen cycloaddition reaction (i.e., click chemistry); it was then used as a chain transfer agent (CTA) for the ROMP of cyclooctadiene. The ROMP was carried out with Grubbs second generation catalyst and the POSS‐terminated PCOD telechelics with variable lengths of PCOD were obtained by controlling the molar ratios of CTA to cyclooctadiene. All the POSS‐terminated PCOD telechelics in bulks were microphase‐separated; the morphologies were quite dependent on the lengths of PCOD midchains. The POSS end groups can promote the crystallization of PCOD chains at room temperature, which was in marked contrast to the case of plain PCOD. Compared to the plain PCOD, the POSS‐terminated PCOD telechelics displayed improved thermal stability and surface hydrophobicity. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 223–233     

Synthesis of telechelic anthraquinone‐functionalized polybutadiene via ROMP and study of its photo‐oxidation and UV crosslinking behaviors

Telechelic anthraquinone‐functionalized polybutadiene (AQ‐PB‐AQ) was synthesized by ring opening metathesis polymerization to achieve homogeneous dispersion of AQ groups in the polymer matrix. It was observed that the AQ end groups act as a sensitizing group resulting in photo‐induced crosslinking and oxidation reaction at the olefin groups in the PB. The process was confirmed by comparing the polymer's mass loss and Fourier transform infrared (FTIR) spectra with those of telechelic diacetoxy‐functionalized PB (AcO‐PB‐OAc) which did not show any difference before and after ultraviolet irradiation. Homogeneity of the AQ groups in PB matrix results in rapid crosslinking of PB in a short period of time (<4 min) while a simple blend of AQ methyl ester in AcO‐PB‐OAc matrix did not show such behavior. Photo‐oxidative reaction has concurrently occurred during the crosslinking reaction. Generation of  OH,  OOH, and carbonyl groups in the matrix during the photo‐oxidation was verified by FTIR, elemental analysis, and water contact angle measurements. A plausible mechanism for the process was proposed in which the photo‐sensitized AQ groups abstract hydrogen from the PB chain to yield reactive radical species, initiating oxidative crosslinking, and degradation of PB or reduction of AQ to hydroanthraquinone species. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1249–1258     

Stereoselective Synthesis of cis‐2,5‐Disubstituted Pyrrolidines via Copper‐Catalyzed Cyclization of Alkenes

An efficient methodology for the stereoselective synthesis of cis‐2,5‐disubstituted pyrrolidines using copper catalyst was developed. The corresponding cis‐2,5‐disubstituted pyrrolidines could be obtained in reasonable yields and with good stereoselectivities in the presence of 4,4′‐di‐tert‐butyl‐2,2′‐bipyridine as ligand and 1‐methyl‐2‐pyrrolidinone as solvent.