Microwave Assisted Extraction of Polycyclic Aromatic Hydrocarbons and their Determination by Gas Chromatography–Mass Spectrometry: Validation of the Method and Application to Marine Sediments

Microwave-assisted extraction of sixteen polycyclic aromatic hydrocarbons and their gas chromatographic mass spectrometric detection are presented herein. An efficient extraction was achieved in 15 minutes using 10 mL of 1:1 n-hexane-acetone while a clean-up step was developed studying the elution curves on solid phase extraction silica cartridges. The analytical method was optimized and validated using a certified reference marine sediment; satisfactory figures of merit were obtained with limits of detection in the range 0.001–0.004 µg/g, precision within 6%, and good linearity (regression coefficients generally higher than 0.998, in the concentration range 0.010–1.000 µg/mL). The developed method was successfully applied to the determination of polycyclic aromatic hydrocarbons in real marine sediments collected in two coastal areas of Italy exposed to different anthropic impact: three tourist sites of Liguria and the Venetian Lagoon. The total concentration of the analytes in the samples was in the range 1.027–3.827 µg/g and the use of common markers suggested their probable pyrolytic origin.     

A comparison of direct thermal desorption with solvent extraction for gas chromatography-mass spectrometry analysis of semivolatile organic compounds in diesel particulate matter

Direct thermal desorption-gas chromatography-mass spectrometry (DTD-GC-MS) is a technique that is finding application in the characterisation of the semivolatile organic carbon fraction of ambient and combustion source particulate matter (PM) collected on filters. In this study, three DTD-GC-MS methods were assessed and compared to a conventional solvent extraction method for analysis of a mixture of target analytes in solution and of diesel PM collected on quartz filters. The target analytes included n-alkanes, hopanes, steranes and polycyclic aromatic hydrocarbons. This study showed that while the three DTD-GC-MS methods were generally comparable to the solvent extraction method, (1) the choice of calibration strategy and calibration materials has a significant impact on the measured accuracy of a method; (2) very large variations were seen in all methods for the more volatile compounds such as C₁₀ to C₁₃ n-alkanes and naphthalene; (3) accuracy, defined as difference from the known concentration of a liquid sample, ranged from 5% to 32%; (4) precision, defined as the relative standard deviation, ranged from 4% to 16%. The average difference of DTD-GC-MS results from the solvent extraction results for the diesel PM filters ranged from 20% to 40%. This difference was driven by the large number of target analytes present at relatively low concentrations (<25 pg/mm²) and their corresponding higher variability. Differences in performance among the compound classes were noted. Minimum detection limits for the DTD-GC-MS methods were on the order of 0.1 to 1 pg/mm² and were as good as or better than those obtained for the solvent extraction method.     

Micelle formation for improvement of continuous subcritical water extraction of polycyclic aromatic hydrocarbons in soil prior to high-performance liquid chromatography-fluorescence detection

A new method for the extraction-individual separation-determination of polycyclic aromatic hydrocarbons (PAHs) in soil is reported. The method is based on the integration of three steps: continuous subcritical extraction, solid-phase clean-up/preconcentration, and HPLC separation with post-column fluorimetric determination. Sodium dodecyl sulfate (SDS) was added to the water for favouring the extractability of the low-polarity analytes. Soil samples spiked with the target PAHs were subjected to static-dynamic extraction with SDS-water at 50 bar, 150 degrees C, for 15 min of static extraction and 10 min dynamic extraction at a flow-rate of 3 ml/min. Recoveries from 73.6 to 110.4% were obtained in the presence of SDS versus 30 to 80% obtained with water as extractant. The calibration graphs provided by HPLC-fluorimetric detection were run between 0.031 and 0.375 microg/ml for each analyte with regression coefficients between 0.917 and 0.999 and precision, expressed as RSD, between 1.2 and 11.5%. The method was applied to a certified reference material [CRM 524, BCR (Community Bureau of Reference), industrial soil/organic] for validation and the results obtained were in agreement with the certified values.     

A liquid chromatography tandem mass spectrometry method for simultaneous analysis of 46 atmospheric particulate-phase persistent organic pollutants and comparison with gas chromatography/mass spectrometry

A novel multi-analyte method for the simultaneous determination of 46 compounds of environmental concern, most of them belonging to the category of persistent organic pollutants, was developed using high-performance liquid chromatography and the results were compared to those obtained by gas chromatography. This study was performed in perspective of a cumulative exposure assessment of substances of health concern in environments where high levels, relatively to airborne particulate matter, can be found. The target compounds included polychlorinated biphenyls, brominated flame–retardants and derivatives of polycyclic aromatic hydrocarbons.

The multi-analyte method was evaluated in air particulate matter in terms of reproducibility, linearity, recovery, limits of detection and quantification and matrix effect. The recovery was above 70% for all the analytes, whereas limits of quantification ranged between 23 and 390 pg?m^?3 in liquid chromatography and less than ten times in gas chromatography–mass spectrometry.

Matrix effect was generally negligible for both the techniques, except the case of the detection of oxygenated derivatives of polycyclic aromatic hydrocarbons by gas chromatography.

In order to demonstrate the efficacy and to assess the method performances (accuracy and precision), both the techniques were applied to standard reference materials, and the results were compared, discussing their advantages and disadvantages.

The method was finally applied to a real sample of indoor airborne particulate matter with aerodynamic diameter ≤4 μm (PM₄).

We demonstrated that liquid chromatography was the only technique able to analyse the 46 compounds, including thermally degradable ones, with a single chromatographic run without derivatisation steps. On the other hand, gas chromatography still presents higher sensitivity for the detection of some of the investigated compounds. This study can be considered only explorative and further improvements can be expected with new-generation LC-MS instruments (10–100 times more sensitive).     

Solid-phase clean-up in the liquid chromatographic determination of polycyclic aromatic hydrocarbons in edible oils

A solid-phase extraction (SPE) method for sample clean-up, followed by reversed-phase high-performance liquid chromatography (HPLC) with fluorescence detection is reported for the determination of polycyclic aromatic hydrocarbons (PAHs) in edible oils. The effects of experimental variables, such as washing and elution solvents, sample solvent and drying time have been studied using C18 cartridges. Recoveries and selectivity using other sorbent materials (C8, C2, CH, PH and NH2) were also examined, with C18 being the best one. The recoveries ranged between 50 and 103% depending on the molecular mass of the PAH. The limits of quantitation were lower than 1 ng/g for most PAHs and good precision was achieved. The method was validated using certified reference materials.     

Development of a method for simultaneous analysis of PCDDs, PCDFs, PCBs, PBDEs, PCNs and PAHs in Antarctic air

The development of a unique analytical method for the determination of five classes of persistent organic pollutants (POPs) in atmospheric gas and the particle phase through gas chromatography coupled to high-resolution mass spectrometry is presented. Every step of the pre-analytical and analytical optimization process is described. Great effort was put into simplifying the traditional techniques, with reference to EPA and literature methods. Automated instruments were used for sample extraction and cleanup in order to enhance repeatability and reduce contamination risks. Unlike most common approaches, no separation of the analytes was performed before the GC analysis in order to avoid sample fractionation and to save time and materials. This allowed low instrumental and method detection limits (pg to sub-pg) to be achieved. Accuracy and precision were tested by fortifying the matrix and analysing standard reference materials (NIST SRM 1649b Urban Dust and 2585 Organic Contaminants in House Dust). The method was applied to five samples from Terra Nova Bay, Antarctica. Concentrations of polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs), polychlorinated biphenyls (PCBs), polychlorinated naphthalenes (PCNs), polybrominated diphenyl ethers (PBDEs) and polycyclic aromatic hydrocarbons (PAHs) are presented. Lighter compounds dominate the distribution and are mainly present in the gaseous phase. The observed pattern may be attributable to long-range transport. Results are in general agreement with literature data, where available.     

Analysis of organic pollutants in water at trace levels using fully automated solid-phase extraction coupled to high-performance liquid chromatography

Summary A method has been developed for the determination of trace levels of 32 pesticides, 19 explosives and 16 polycyclic aromatic hydrocarbons (PAH) in water in three individual steps. Solid-phase enrichment (SPE) is coupled to high-performance liquid chromatography (HPLC) with a fully automated system. The organic pollutants are enriched on reusable cartridges packed with adsorbent materials: pesticides and explosives on a mixed bed of divinylbenzene-ethylvinylbenzene copolymers (LiChrolut EN^?) and perfluorinated polyethylene (PolyF^?), and polycyclic aromatic hydrocarbons on C₁₈-modified silica (Zorbax^? ODS1). Thermally assisted desorption (TAD) has been shown to increase the recovery of analytes significantly. As all enriched analytes are transferred to the detector, only fifty millilitres of sample is needed for each single on-line analysis, compared with at least a litre for conventional methods. The separation of the enriched organic analytes is performed on specialized HPLC columns based on reversed-phase materials. The limits of detection of the system employed were found to be below 100 ng L⁻¹. Use of fluorescence detection for the polycyclic aromatic hydrocarbons resulted in limits of detection in the upper pg L⁻¹ range. Thek values, number of theoretical plates, the recovery rates and the limits of detection of this method for fast screening of organic pollutants from three fifty-millilitre aqueous samples are described. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Optimization of solid‐phase microextraction using Taguchi design to quantify trace level polycyclic aromatic hydrocarbons in water

This article introduces a simple, rapid, and reliable solid‐phase microextraction (SPME) method coupled with GC‐MS for the quantitative determination of 16 polycyclic aromatic hydrocarbons in water. In this study, the Taguchi experimental design was used to optimize extraction conditions of polycyclic aromatic hydrocarbons using SPME method to obtain highly enriched analytes. Consequently, quantitative determination of polycyclic aromatic hydrocarbons in water was achieved by GC‐MS technique. The selected parameters affecting enrichment of polycyclic aromatic hydrocarbons were sample extraction time, stirring speed, temperature, ionic strength, and pH. The study revealed that optimal operating conditions were found to be 90‐min extraction time, 1400 rpm stirring speed, and 60°C sample temperature. The effect of ionic strength and pH were shown to be insignificant. Optimized conditions were also reevaluated by placing the 16 polycyclic aromatic hydrocarbons into several subgroups based on their molecular weight. The extraction efficiency of polycyclic aromatic hydrocarbons with low molecular weight was shown to be a function of only the extracting temperature. Satisfactory results were obtained for linearity (0.983–0.999), detection limits (2.67–18.02 ng/L), accuracy (71.2–99.3%), and precision (4.3–13.5%). The optimum conditions reported by other design approaches were evaluated and generalized optimum conditions were suggested.     

Mesoporous titanium oxide with high‐specific surface area as a coating for in‐tube solid‐phase microextraction combined with high‐performance liquid chromatography for the analysis of polycyclic aromatic hydrocarbons

Stainless‐steel wires coated with mesoporous titanium oxide were placed into a polyether ether ketone tube for in‐tube solid‐phase microextraction, and the coating sorbent was characterized by X‐ray diffraction and scanning electron microscopy. It was combined with high‐performance liquid chromatography to build an online system. Using eight polycyclic aromatic hydrocarbons as the analytes, some conditions including sample flow rate, sample volume, organic solvent content, and desorption time were investigated. Under optimum conditions, an online analysis method was established and provided good linearity (0.03–30 μg/L), low detection limits (0.01–0.10 μg/L), and high enrichment factors (77.6–678). The method was applied to determine target analytes in river water and water sample of coal ash, and the recoveries are in the range of 80.6–106.6 and 80.9–103.5%, respectively. Compared with estrogens and plasticizers, extraction coating shows better extraction efficiency for polycyclic aromatic hydrocarbons.     

Application of sunflower stalk‐carbon nitride nanosheets as a green sorbent in the solid‐phase extraction of polycyclic aromatic hydrocarbons followed by high‐performance liquid chromatography

A green biocomposite of sunflower stalks and graphitic carbon nitride nanosheets has been applied as a solid‐phase extraction adsorbent for sample preparation of five polycyclic aromatic hydrocarbons in different solutions using high‐performance liquid chromatography with ultraviolet detection. Before the modification, sunflower stalks exhibited relatively low adsorption to the polycyclic aromatic hydrocarbons extraction. The modified sunflower stalks showed increased adsorption to the analytes extraction due to the increase in surface and existence of a π–π interaction between the analytes and graphitic carbon nitride nanosheets on the surface. Under the optimal conditions, the limits of detection and quantification for five polycyclic aromatic hydrocarbons compounds could reach 0.4–32 and 1.2–95 ng/L, respectively. The method accuracy was evaluated using recovery measurements in spiked real samples and good recoveries from 71 to 115% with relative standard deviations of <10% have been achieved. The developed method was successfully applied for polycyclic aromatic hydrocarbons determination in various samples—well water, tap water, soil, vegetable, and barbequed meat (kebab)—with analytes contents ranging from 0.065 to 13.3 μg/L. The prepared green composite as a new sorbent has some advantages including ease of preparation, low cost, and good reusability.     

Determination of polycyclic aromatic hydrocarbons in water by a novel mesoporous‐coated stainless steel wire microextraction combined with HPLC

A novel mesoporous‐coated stainless steel wire microextraction coupled with the HPLC procedure for quantification of four polycyclic aromatic hydrocarbons in water has been developed, based on the sorption of target analytes on a selectively adsorptive fiber and subsequent desorption of analytes directly into HPLC. Phenyl‐functionalized mesoporous materials (Ph‐SBA‐15) were synthesized and coated on the surfaces of a stainless steel wire. Due to the high porosity and large surface area of the Ph‐SBA‐15, high extraction efficiency is expected. The influence of various parameters on polycyclic aromatic hydrocarbons extraction efficiency were thoroughly studied and optimized (such as the extraction temperature, the extraction time, the desorption time, the stirring rate and the ionic strength of samples). The results showed that each compound for the analysis of real water samples was tested under optimal conditions with the linearity ranging from 1.02×10^?3 to 200 μg/ L and the detection limits were found from 0.32 to 2.44 ng/ L, respectively. The RSD of the new method was smaller than 4.10%.     

Total concentration analysis of polycylic aromatic hydrocarbons in aqueous samples with high suspended particulate matter content

The European water framework directive (WFD) requires priority pollutants to be measured in the whole water sample and not only in the dissolved phase. However, it does not give clear definitions on how to achieve this. To overcome this limitation, a new methodology of sample preparation procedure for the analysis of polycyclic aromatic hydrocarbons on the basis of extraction disks is introduced here. The automatable procedure includes a “one-step” extraction of the analytes both dissolved in the liquid phase of the sample and sorbed to suspended particulate matter. The latter is extracted concurrently with the solid-phase extraction (SPE) material within the elution step of the procedure. Separation, identification, and quantification of the analytes is performed by GC–MS. Results from surface water samples spiked with certified sediment up to 1000 mg/l are presented in this work and compared with results derived from liquid–liquid extraction (LLE). Most measured values are within or at least near certified uncertainty limits of the sediment. The SPE disk method shows much higher recoveries and better precision (relative standard deviations between 2% and 11%) than the standard LLE method. For all substances under investigation, the limits of quantification achieved range between 0.001 and 0.005 μg/l.     

Preparation of a reference mussel tissue material for polycyclic aromatic hydrocarbons and trace metals determination

Due to high cost of certified reference materials (CRMs), reference materials (RMs) are preferred to check the method performance in environmental analysis. In this work, a laboratory reference material (LRM) was prepared and characterised to carry out the quality control in monitoring analysis of eight polycyclic aromatic hydrocarbons (PAHs) and nine trace metals in mussel tissue. Mussels were collected in a naturally polluted area. Before the reference material was bottled, the mussel tissue was stabilised by freeze-drying, ground and sieved. For the material characterisation, several statistical tests were applied to check the homogeneity of the analytes in the tissue, and a stability test was performed to study the effect of the storage temperature in the analyte concentration. Other characteristics such as specific density, moisture and lipid contents as well as particle size distribution of the material were determined. Although the LRM had a homogeneous distribution for all PAHs and almost all metals, the stability study showed different results at both storage temperatures studied. For both PAHs and trace metals, the material was suitable to assure the quality control of the analysis.     

Fluidized-bed extraction of polycyclic aromatic hydrocarbons from contaminated soil samples

Summary Due to the carcinogenity and ubiquity of polycyclic aromatic hydrocarbons in the environment they are of ongoing interest to analytical chemistry. In this study, a comparison of the classic Soxhlet extraction and, fluidized-bed extraction, has been conducted. The extraction of polycyclic aromatic hydrocarbons by this technique has been optimized considering as experimental variables the variation of the number of extraction cycles and the holding time after reaching the heating temperature by means of a surface response design. The significance of the operational parameters of the fluidized-bed extraction on the performance characteristics has been investigated. For the determination of the analytes a selective clean-up of the extracts followed by a fast gas chromatography method with mass spectrometric detection was used, resulting in low limits of detection (0.2 pg μL⁻¹). The accuracy of the complete analytical method was established by extraction and analysis of reference materials.     

Validated analytical strategy for the determination of polycyclic aromatic compounds in marine sediments by liquid chromatography coupled with diode-array detection and mass spectrometry

The aim of this work was to optimise and validate the experimental conditions for the analysis of 20 polycyclic aromatic compounds (PACs) [19 polycyclic aromatic hydrocarbons (PAHs) and dibenzothiophene as polycyclic aromatic sulphur heterocycle (PASH)] in marine sediments by reversed-phase high-performance liquid chromatography (LC) coupled to photodiode array detection (DAD) and to mass spectrometry (MS). The LC-MS interface used was atmospheric pressure chemical ionization (APCI) in the positive ion mode. The operational parameters of the APCI interface and MS detection, such as organic modifier, fragmentation voltage, gain, vaporizer temperature, corona current, capillary voltage, drying gas (N2) and nebulizer pressure, were studied. The sediments were subjected to microwave-assisted solvent extraction (MAE) and clean-up by solid-phase extraction (SPE). The relevance of the selected PACs lies in the fact that 16 PACs are classified by the US Environmental Protection Agency as priority pollutants; 17 PACs are detected in the Prestige oil spill; and 8 PACs are included in the priority substance list of the EU water policy. Recoveries from 47% to 102% were obtained for SRM 1944 certified reference sediment. The limits of quantitation were lower than 100 ngg(-1) dry weight for most PACs, and good precision was achieved.     

Minimising the risk of some systematic errors by the use of the single vessel principle for cold vapour atomic absorption spectrometric determination of mercury in biological solids

The suitability of the single vessel principle (performing all steps of an analytical procedure in one vessel) for cold vapour atomic absorption spectrometric determination of mercury in biological solids was evaluated. The single vessel method gave a lower mean blank level with better precision, hence lower detection limits, as compared to the conventional method. The determination of total mercury in biological standard reference materials by the single vessel method also produced significantly higher mercury values and better precision than the conventional method. However, the mercury concentrations obtained in certified reference materials by the use of both methods were close to the mean certified values. Moreover, the use of the single vessel method is cost effective, rapid and environment friendly. The use of the single vessel technique is therefore recommended for accurate and reliable determination of mercury in biological solids.     

Simplified procedures for the analysis of polycyclic aromatic hydrocarbons in water, sediments and mussels

We describe in this paper simple and robust analytical protocols to determine the 16 polycyclic aromatic hydrocarbons (PAHs) of the US Environmental Protection Agency priority list in water, sediment and mussels. For water samples, eight different solid-phase extraction (SPE) sorbents have been compared and among them, C18 provided highest recoveries and limits of detection of 0.3-15 ng/L. For lyophilized sediments, Soxhlet and ultrasonic extraction were compared, and the last one permitted to recover all analytes with highest repetitivity and was validated by analysing a certified reference material. Finally, the analysis of mussels was undertaken using Soxhlet, ultrasonic and pressurized liquid extraction (PLE) and the performance of several clean-up steps are compared. Whereas for the former two, incomplete recovery or losses of some analytes were evidenced, PLE permitted a more efficient extraction and although alkaline digestion was necessary to remove coextracted compounds, the method gave acceptable recoveries and limits of detection of 0.5-7.7 microg/kg dry mass, as for sediments. In all cases, analysis was performed by gas chromatography coupled to mass spectrometry and internal standard quantification was performed using five deuterated PAHs. Each method performance is discussed for the three matrices analysed and the paper reports advantages and disadvantages of each for their routine application in monitoring programs.     

Loading controlled magnetic carbon dots for microwave‐assisted solid‐phase extraction: Preparation,extraction evaluation and applications in environmental aqueous samples

An adsorbent of carbon dot@poly(glycidyl methacrylate)@Fe₃O₄ nanoparticles has been developed for the microwave‐assisted magnetic solid‐phase extraction of polycyclic aromatic hydrocarbons in environmental aqueous samples prior to high‐performance liquid chromatography with UV/visible spectroscopy detection. Poly(glycidyl methacrylate) was synthesized by atom transfer radical polymerization. The chain length and amount of carbon dots attached on them can be easily controlled through changing polymerization conditions, which contributes to tunable extraction performance. The successful fabrication of the nano‐adsorbent was confirmed by transmission electronic microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and vibrating sample magnetometry. The extraction performance of the adsorbent was evaluated by using polycyclic aromatic hydrocarbons as model analytes. The key factors influencing the extraction, such as microwave power, adsorption time, desorption time and desorption solvents were investigated in detail. Under the optimal conditions, the microwave‐assisted method afforded magnetic solid‐phase extraction with short extraction time, wide dynamic linear range (0.02–200 μg/L), good linearity (R² ≥ 98.57%) and low detection limits (20–90 ng/L) for model analytes. The adsorbent was successfully applied for analyzing polycyclic aromatic hydrocarbons in environmental aqueous samples and the recoveries were in the range of 86.0–124.2%. Thus, the proposed method is a promising candidate for fast and reliable preconcentration of trace polycyclic aromatic hydrocarbons in real water samples.     

Headspace single drop microextraction combined with HPLC for the determination of trace polycyclic aromatic hydrocarbons in environmental samples

A new method by combining headspace single drop microextraction (HS-SDME) with HPLC fluorescence detection for the determination of trace polycyclic aromatic hydrocarbons (PAHs) in environmental samples was developed. Aqueous solution of saturated beta-cyclodextrin was used as extraction solvent and five PAHs were employed as target analytes. The factors affecting the extraction efficiency were studied in detail and the optimal extraction conditions were established. Beta-cyclodextrin was found to play two important roles, one is the improvement of extraction efficiency of target analytes and the other is the enhancement of their fluorescence intensities in HPLC fluorescence detection. The detection limits for the target analytes were found to be in the range of 0.004-0.247ng/ml and the relative standard deviations (R.S.D.s) of 5.1-7.1% were obtained. The proposed method was applied to the analysis of trace PAHs in environmental samples with satisfactory results.     

Determination of Polycyclic Aromatic Hydrocarbons in Mosses by Ultrasonic-Assisted Extraction and Gas Chromatography–Tandem Mass Spectrometry

A facile method for the determination of polycyclic aromatic hydrocarbons in mosses is reported using ultrasonic-assisted extraction and gas chromatography–tandem mass spectrometry. The efficiency of ultrasonic-assisted extraction and the reagents was optimized. Tandem mass spectrometry with selective reaction monitoring was used to enhance the selectivity to reduce matrix interferences and simplify the purification protocol. The detection limits were from 0.1 to 2.0?ng/mL. The linear calibration range was two orders of magnitude and the coefficients of linear correlation exceeded 0.9992 for all analytes. The relative standard deviations within 1 day and 3 days were less than 9.0%. Recoveries from 56.8 to 109.0% were obtained in fortified mosses. The rapid, low solvent gas chromatography–tandem mass spectrometry method was used to determine polycyclic aromatic hydrocarbons in mosses.