爆炸闪光脉冲波形实时采集与存储系统

介绍了一种针对爆炸时刻的测量而设计的爆炸波形实时采集与存储系统.该系统通过可编程逻辑阵列控制模数转换器的时序来完成数据实时采集,同时将采集到的数据实时存储到闪速存储器中.数据采集存储结束后,后系统通过PC/104总线传至PC/104计算机以便进行数据的后续处理获得完整的爆炸波形来判断爆炸时刻.     

基于FPGA高速数据采集与存储系统的设计

对高速数据采集系统进行了研究,基于其采集速率的问题,提出了一种基于FPGA的高速数据采集系统。利用FPGA实现对12bit的A/D转换器ADC12D800的控制,使用其1.6Gsps双沿采样工作模式完成对400MHz以下高频信号的数据采集。通过设计数据存储方式来降低数据传输速率,使数据经USB传至PC机来实现高频信号地实时采集与存储。实验结果表明它可以实时、高效地完成数据采集,可以应用到雷达、通信、电子对抗等领域。     

基于OMAPL138 FPGA构架的PC104主板检测系统

为了对PC104主板进行自动检测,分析了PC104主板工作原理及其总线时序,提出了一种基于ARM FPGA的嵌入式检测系统的设计方案。该方案采用德州仪器(TI)双核架构的高性能芯片OMAPL138中的ARM核来实现检测系统的应用管理,DSP核实现数据的处理,并利用FPGA技术来实时采集PC104总线数据。检测系统在Linux操作系统下,通过人机交互方式实现了PC104主板的各种功能的自动检测。实验结果显示该检测快速可靠,为PC104主板的自动检测提供了一种有效的方法。     

基于OMAPL138和FPGA构架的PC104主板检测系统

为了对PC104主板进行自动检测,分析了PC104主板工作原理及其总线时序,提出了一种基于ARM+FPGA的嵌入式检测系统的设计方案;该方案采用德州仪器(TI)双核架构的高性能芯片OMAPL138中的ARM核来实现检测系统的应用管理,DSP核实现数据的处理,并利用FPGA技术来实时采集PC104总线数据;检测系统在Linux操作系统下,通过人机交互方式实现了PC104主板的各种功能的自动检测;实验结果显示该检测快速可靠,为PC104主板的自动检测提供了一种有效的方法。     

基于DSP+FPGA的实时信号采集系统设计与实现

为了提高对实时信号采集的准确性和无偏性,提出一种基于DSP+FPGA的实时信号采集系统设计方案。系统采用4个换能器基阵并联组成信号采集阵列单元,对采集的原始信号通过模拟信号预处理机进行放大滤波处理,采用TMS32010DSP芯片作为信号处理器核心芯片实现实时信号采集和处理,包括信号频谱分析和目标信息模拟,由DSP控制D/A转换器进行数/模转换,通过FPGA实现数据存储,在PC机上实时显示采样数据和DSP处理结果。通过仿真实验进行性能测试,结果表明,该信号采集系统能有效实现实时信号采集和处理,抗干扰能力较强。     

一种便携式多生理参数采集系统的设计

本文设计了一种便携式多生理参数采集系统。该系统可以实现对人体呼吸、指脉、动作、皮电、血压、心电等六个体征参数的采集;该系统利用串口转USB传输可以实现采集到的人体生理参数与PC间的相互传输,测量结果和分析报告可以在PC 机进行实时显示和存储或者可以通过Internet向远程医疗服务中心进行数据的上传、备份、分析与反馈。所以,利用该系统可以实现对人体体征参数实时、连续的采集与监测。     

基于线阵CCD的高速光谱信息采集系统的研究

针对爆炸时刻光谱信息量大、存在时间短的特点,设计了一款基于线阵CCD高速光谱信息采集系统.系统以FPGA作为主控芯片不仅为CCD提供工作时序,同时还控制着信号调理、模数转换和光谱信息的存储与传输.最后,通过USB串行总线将采集到的光谱信息传输至上位机进行后续处理.结果表明,利用该系统可在一次爆炸过程的100ns时间内完成四个时刻爆轰温度的测量,具有较高的测量精度和速度,可实现爆轰过程中高速动态光谱信息的采集与存储,并可应用于其它瞬态信息的获取领域.     

基于LabVIEW的电流信号采集系统的设计和实现

在机电设备、精密器件等研发工作和电路校准、传感器应用等日常实验中,数字多用表常被用于微弱信号的测量,但数字多用表只能实时显示采集到的信号,不能存储信号,在实验和应用中无法将检测到的波形、数据和实验状态实时对应,只能通过人工肉眼估计读取,给实验和应用带来了一定的困扰。为了解决该问题,开发了一个基于LabVIEW的电流信号采集系统,该系统可以将采集到的波形实时显示在面板上,同时将检测到的准确电流数据和读取时间存储到PC机。实验结果表明,该系统可以更好地显示电流信号,同时可以进行信号的存储,避免了肉眼读取数字多用表的误差,增强了读取数据的准确性。     

基于FT245RL和FPGA的6路数据采集系统设计

针对大规模数据采集过程中存在数据量大与传输速度慢的矛盾,本文设计了基于FT245RL和FPGA的6路数据采集系统。该设计采用Xilinx公司的FPGA作为整个系统的核心,控制A/D转换器实现6路模拟数据的同步采集,并将转换后的数字信号存储到Flash中,最终通过USB2.0转换芯片将数据传输到上位机。试验表明,该数据采集系统能够满足对大容量数据实时采集、存储和上传的要求,具有工作稳定,可靠性高,传输速度快的特点,能够广泛应用于大规模数据的采集。     

基于GPRS的下水道气体远程监测系统设计

为了提高城市下水道气体监测的实时性和可靠性,本文设计了基于GPRS的下水道气体远程监测系统。该系统主要包括前端气体采集模块、GPRS数据无线传输模块、数据接收模块及监控中心;气体采集模块由气体传感器和数据采集单片机组成;单片机实时采集气体传感器中的数据,并将采集到的数据通过GPRS无线传输模块进行实时上传;数据接收模块把接收到的数据传送至监控中心服务器,由服务器对数据进行处理、显示、存储和统计等。通过对18个监测点的监测实验效果表明,该系统运行稳定可靠,能实现对下水道气体远程采集、无线传输和实时监测的目的。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.